Headphone jack problems... - AT&T Samsung Galaxy Note I717

I got new headphones about a week ago (shure se535) and had been using them with my note for at least twenty hours already. Yesterday while walking to work I was using them with my note and they were working just fine, and same with right after. Then when I was getting ready for bed I wanted to listen to some music so I popped them in and picked a song and only the left side worked! so I threw them in my laptop and they both worked. Tried them in the note.. only the left works.
When I push on the headphone jack slightly to one side, the signal returns to the other ear.. I checked for lint in the hole but it still looked brand new. It seems as if the little connector inside the jack for the right side has somehow become almost flush with the rest of the jack, if not pushed in somehow. The weird thing is, when I tried it with the stock headphones with mic, both sides worked! wtf!. It doesn't make any sense lol.
What should I do? Send phone in for warranty repair? Has anyone else had similar problems?

It happens to me too. But it's random.
ParaNOTE Android

I had the same issue with my old Shure headphones the other day. The Samsung headset works fine with the Note. The Shures work fine with my laptop. It's intermittent though with the Note.

This is discouraging to hear. 3.5mm jacks have been in use for so freaking long that you'd think there wouldn't be any problems...
I'm worried that if I do go to Telus and get a repair done that they will say there is no problem and not even touch it. I wonder why my $500 shures out of the blue lost connection, yet the cheapo OEM headphones work lol. I'm very careful to not let anything put pressure on the jack when plugged in..
Sigh.
Sent from my SAMSUNG-SGH-I717 using Tapatalk 2

Related

[Q] Atrix thinks wired headset button is CONSTANTLY BEING PUSHED

Music plays fine out of the wired headset...it always has. The headset has functioned properly until about two weeks ago. At that time, my Atrix began to think that I was pressing the headset button. Constantly. Over and over. Any time the screen is on with the headset in, it redials automatically. When the screen is off, it does it too, because when I turn the screen on, it gives me the vlingo vs. voice command box. Also, when I make a call with the headset plugged in, the other person can somehow not hear me at all, until they call me back, and it's fine. The phone thinks the headset button is being pressed once every few seconds. THIS IS INCREDIBLY ANNOYING.
I know it's not the headset, because I've tried three different headsets (two by Motorola, both the 'official' wired headsets of the Atrix, and one third-party), all with the same result. Also, it's not just my phone! Oddly enough, I replaced my Atrix with AT&T's warranty, and THE NEW PHONE HAD THE SAME PROBLEM.
Has anyone else experienced this, or have the slightest clue what is going on? I've looked around the internet for weeks now and I haven't seen a single instance of it. Pleeeeease. This is brutal.
My headset with mic and button does not have any issues. Its the bose MIE2 mobile phone headset.
Yes I have experienced this as well and it is super annoying I will prob swap it out and hope I don't get another messed up one. Sometimes when I am in my car and connected to my bluetooth handsfree it'll do the same thing and start a song playing and I don't even push anything!!! Hope someone figures this one out.
theres defo something funny about the atrix headphone jack and remote controls.
At first my nexus one remote worked fine with it, but it started doing funny things, then flat out would go crazy (issuing commands without me touching it etc.)
Gave up and went wireless, now I only use wired @ the gyma dn they're just dumb headphones w/out remote
ME TOO!!
Yes, yes, and yes on having this problem. I use my headphones (SkullCandy FMJ) sometimes when riding my bike and yesterday all I kept hearing was "please say a command...did you say...I'm sorry please try again" over and over...hard to deal with at 70MPH!!! Hope this gets fixed, I thought it was my headphones, but it sounds like another GB issue. I don't have any problems when using my SENA SMH10 Bluetooth inside the helmet.
I had this same problem, mine got randomly solved. You could find how the wiring world for the Atrix and block that connection or cut off the controller on the headphone and solder your headphones back together.
Sent from my MB860 using XDA App
Thanks for the feedback, but a)I'm not looking to do any soldering or rewiring (I'm good with software mods, but not hardware mods), and b) it never happened until recently, then I swapped out the phone for a new Atrix, and it happened right off the bat - again with all three headsets. Tried a bluetooth, worked fine, no problem.
I tried a new headset (skull candy something-or-other) and it's been working so far, inexplicably.
I made a voodoo doll of my Atrix and poked it a bunch of times in its little voodoo headphone jack. Seems to have done the trick. I'd recommend that method.
I have this problem too with my headphones from my Sony x1, or x10. I cant remember which one. But as soon as I plug them in the phone goes nuts!
Which really sucks because they are they best headset/ headphones I have ever used for my funny shaped ears.
I think mine fixed after I dropped it and the headphones came out Anyways as long as its resolved that's awesome.
Sent from my MB860 using XDA App
Anyone having the problem using the pure music widget, by any chance? Uninstalled that and hasn't happened since with any headset.
Sent from my MB860 using XDA Premium App
i also started to experience this issues.At first i thought it is kernel or ROM issue but then after multiple test and experiment it is the Atrix 3.5mm headset jack is the culprit.If im not mistaken it is due to pressure contact sensor inside headphone jack.Please anyone know how to rectify this kind of problem do post your solutions for us.TQ
rknight68 said:
Yes, yes, and yes on having this problem. I use my headphones (SkullCandy FMJ) sometimes when riding my bike and yesterday all I kept hearing was "please say a command...did you say...I'm sorry please try again" over and over...hard to deal with at 70MPH!!! Hope this gets fixed, I thought it was my headphones, but it sounds like another GB issue. I don't have any problems when using my SENA SMH10 Bluetooth inside the helmet.
Click to expand...
Click to collapse
You bike at 70MPH? Holy.
so no one found a real fix or solution for this problem? Maybe we need to make a petition and submit to motorola
I had the same problem with a BB9700. It ended up being a damaged headphone jack. I figure some crap from my pocket had been in the jack when I plugged in the head set. Which jammed everything into it wrecking the receiving end of things.
Luckily I had a spare housing which came with a new jack. I'm not sure if it's as easy to replace on the Atrix since I haven't had the opportunity to tear it apart yet.
Power amp has settings that fix my controls and it works great.
Sent from my MB860 using XDA Premium App
Still no one ever face this kind of problem?
Can anyone confirm that this could fix our problem? http://forum.xda-developers.com/showthread.php?t=1301998
I have same problem too. But I have this problem on stock ROM and CM10.1 (with 3.1 kernel) ROM. I don't have this problem with any other ROM.

Headphone bug? uneven volume

I plugged my headphones in for the first time today and i realized that the left side was quieter than the right. And I unplugged it and replugged it in and it was fine. Then I tried it again and the left side was lower again. I'm not sure what's causing this or if my tablet is defective. But it seems like a hit or miss on getting even volume from both sides.
Anyone else having this problem or can test it out?
I have te same issue and it happens every time I plug in headphones and its annoying.
For me this only happened when I use my SGS2 headphones on Nook.
Actually, I found that SGS2 headphones only work well on the SGS2. With my laptop they have tons of noise, on nook sometimes I have uneven volume.
Although on SGS2 they have the best sound I've ever heard in headphones..
Have you guys tried other headphones?
I only have the one pair of head phones and they are a generic brand from dollar general and they dont have any issues when i use them with either my pc or psp or phone for that matter
Montisaquadeis said:
I only have the one pair of head phones and they are a generic brand from dollar general and they dont have any issues when i use them with either my pc or psp or phone for that matter
Click to expand...
Click to collapse
My 5$ noise isolation headphones work just fine? O_O
Montisaquadeis said:
I have te same issue and it happens every time I plug in headphones and its annoying.
Click to expand...
Click to collapse
This.
Every single time.
no issues here.
No issues here.
Headphone bug
Yes I too have that problem. Glad to see that it's not just me & mine.
Stupid question - for those having issues, have you tried wiggling or rotating the plug once it is plugged in? Sometimes I find if I have a spot of oxidization on the plug it will cause said uneven volume. It could explain the difference that occurs when you unplug/plug back in.
Another thing to try would be to plug them in when the device is asleep to see if that helps. If there is anything that tries to reduce the "pop" of the sound of plugging in the headphones it *might* affect how they sound after the fact.
Just grasping at straws here based on my experience with other devices.
I was having this problem until I realized I only had my headphones plugged in half way. Don't mean to be a jerk, but have you tried plugging your headphones in just a little further?
Sent from my DROID BIONIC using Tapatalk
no amount of fiddling with the plug helped me at all still have the issue and its annoying since the speaker isnt loud enough when I am out and about.
Another thing to consider - another issue I've had with certain device/headphone combos is that some headphone jacks either don't have a long enough plug or the plastic jacket of the jack interferes just enough with the plug in the device to affect sound (essentially related to downsay's comment). Try a cheap pair of 'phones from the dollar store with a simple jack and see if the problem persists. If so, perhaps the device is defective...
These are a cheap pair of head phones from dollar general lol.
Edit: Plugging the headphones in while the device was asleep seems to have fixed the issue for me for now. Sound is equal in both cans now
I have tried 4 different earphones, they have been plugged in all the way. Some people have no problem, so I'm beginning to think this is a hardware defect. I'm going to exchange mine and will let you guys know if there is a difference. I'll also try out the display model and see if it suffers from this problem.
Glad to hear you got them to work. Please do let us know how it goes with returning the nook tablet.
Sent from my DROID BIONIC using Tapatalk
I replaced my Nook twice partially due to this issue. Same problem on all three and it's always the left channel that is not connecting properly. I have found that I can get a good connection by plugging the jack in slowly. I think this is more a software issue than a hardware issue.
Yea just exchanged my tablet as well and the same issue is there as well as the one at the store. Plugging in slowly does help. Just before it engages the last click, if you hear both channels you're golden. Hopefully this is a software issue because it seems to be random. Unfortunately the one I exchanged has a creaking case, so now back to exchange again.
I stopped by Radio Shack this afternoon and purchased a $5 female to male 1/4" stereo connector. It seems to have solved the problem. I had similar problem years back with an iPaq PocketPC. Due to the shape of the hole on the iPaq/Nook, the headphone/earphone connector isn't inserting deeply enough.
Another solution would be to use something like a Dremel Mototool and shave away some of the excess material on the headphone/earphone adapter, so it can insert a little bit deeper.
ibgap said:
I think this is more a software issue than a hardware issue.
Click to expand...
Click to collapse
What is everyone testing their audio on? The stock media player? Video (what program)? Is it on every application you try?
I haven't had any issues with audio in games, websites or MX player at all other than a loudish pop when some programs start up, but I'm using a set of Denon stereo headphones (so, good (large/long, gold) headphone plugs on it, jiggling the connection does nothing).

[Q] headphone issue

Received my rezound last week, and today I decided to go running with my rezound. Plugged in my headphones (Skullcandy) and noticed only my left headphone would work. I thought it could be the phones, so I plugged them into my fiancee's ipod and they worked perfectly. I tried switching roms to see if that would make a difference. It did not. Is it a fairly common issue? anyone else having this problem?
Thanks
Drew
If sound is coming from only one side then most likely one of the leads is not making contact. Ensure you pushed it in all the way. If still not working call Verizon for a replacement phone as its possible that the contacts in the headphone jack are messed up.
vzw sending me a replacement. Should be here today. Will see if its that or a deeper problem. Thanks
kingofyo1 said:
vzw sending me a replacement. Should be here today. Will see if its that or a deeper problem. Thanks
Click to expand...
Click to collapse
Just so you know, I have skullcandy earbuds and on mine, there's another 3.5mm jack up by the middle of the cord. This connection on my headphones causes an issue with different outputs. Speakers on my computer only put out to one bud, but if I mess with that jack and pull it out about halfway, I get both buds working.
Just make sure you 'isolate the fault' by using different headphones on your old phone, also. Could just be coincidence that when you plug your 'phones into your Rezound, they short out.

[Q] Headphone Jack

Is it just me or is the headphone jack, somewhat tight and also sensitive to changes in position? I mean that it takes a bit more effort than usual in order to plug them in, and yet if you pull them out even slightly, the phone will show that they have been disconnected. Is this normal for HTC Amazes or is it just mine in particular?
Although it isn't an extremely terrible problem yet, I'm worried that the jack will loosen and my headphone plugs will be able to move more freely, which would cause it to disconnect often.
Is this normal and should I be concerned?
P.S. I also seem to have an issue with the camera, it occasionally gives me completely blank/black photos when the flash stalls, as in the LEDs stay on for a few seconds before it takes a picture, and then provides me with a black picture. Is anyone else noticed this as well? I'm using Mobilicity Stock ICS, unrooted and S-On.
Sent from my HTC Amaze 4G using Tapatalk 2
I agree. When I got my amaze I was goign to return it thinking the headphone jack was broken. After an hour I realized I had to apply hulk strength to get it in properly.
skugpezz said:
I agree. When I got my amaze I was goign to return it thinking the headphone jack was broken. After an hour I realized I had to apply hulk strength to get it in properly.
Click to expand...
Click to collapse
Yep. Same here.
skugpezz said:
I agree. When I got my amaze I was goign to return it thinking the headphone jack was broken. After an hour I realized I had to apply hulk strength to get it in properly.
Click to expand...
Click to collapse
ApokrifX said:
Yep. Same here.
Click to expand...
Click to collapse
Does it eventually loosen up after prolonged use?
No it doesnt losen up. I ended up buying Bluetooth earphones.
skugpezz said:
No it doesnt losen up. I ended up buying Bluetooth earphones.
Click to expand...
Click to collapse
Ah, okay. That's good, because I use the headphone jack all the time. Does it also disconnect if you pull it out slightly?
It takes alot to of energy to pull out also.
If you pull out slightly only the left ear will work.
skugpezz said:
It takes alot to of energy to pull out also.
If you pull out slightly only the left ear will work.
Click to expand...
Click to collapse
Yeah, I know it takes a lot of energy to pull it out, but it would be annoying if the jack loosens up and it comes out slightly to the point where it would normally still be connected on normal devices, which would make it disconnect on the Amaze.
MidnightXZ said:
Yeah, I know it takes a lot of energy to pull it out, but it would be annoying if the jack loosens up and it comes out slightly to the point where it would normally still be connected on normal devices, which would make it disconnect on the Amaze.
Click to expand...
Click to collapse
I dont think there is anything that can losen it up lol.
It feels like something locks on to it.
With the force it takes to put in the jack and take it out. I was scared one day I would break it. So I bought a bluetooth headset.
Sucks that beats audio doesnt work over bluetooth.
skugpezz said:
I dont think there is anything that can losen it up lol.
It feels like something locks on to it.
With the force it takes to put in the jack and take it out. I was scared one day I would break it. So I bought a bluetooth headset.
Sucks that beats audio doesnt work over bluetooth.
Click to expand...
Click to collapse
What annoys me though, is that between fully connected and half connected, the the jack will show up as disconnected. It shows as connected when fully in and half way in (with part audio) which intrigues and worries me.
EDIT: Can anyone else verify that the phone shows that headphones are disconnected if they are plugged in between fully plugged in and plugged in halfway?
I have a similar problem. The headphone jack is so tight that if I plug it in my stereo at home or in the car, it will randomly make a pop sound and stop playing music if I so much as touch it. Very irritating. It doesn't do that with headphones, but the jack is so small that I have to cram my headphones in haha. Then again, we should be thankful it's tight and not loose and awful like my old SGSII...
MidnightXZ said:
Is it just me or is the headphone jack, somewhat tight and also sensitive to changes in position? I mean that it takes a bit more effort than usual in order to plug them in, and yet if you pull them out even slightly, the phone will show that they have been disconnected. Is this normal for HTC Amazes or is it just mine in particular?
Although it isn't an extremely terrible problem yet, I'm worried that the jack will loosen and my headphone plugs will be able to move more freely, which would cause it to disconnect often.
Is this normal and should I be concerned?
P.S. I also seem to have an issue with the camera, it occasionally gives me completely blank/black photos when the flash stalls, as in the LEDs stay on for a few seconds before it takes a picture, and then provides me with a black picture. Is anyone else noticed this as well? I'm using Mobilicity Stock ICS, wetunrooted and S-On.
Sent from my HTC Amaze 4G using Tapatalk 2
Click to expand...
Click to collapse
I posted a thread about this same issue about two weeks ago
justin lamantia said:
I posted a thread about this same issue about two weeks ago
Click to expand...
Click to collapse
Which issue?
Sent from my HTC Amaze 4G using Tapatalk 2
I hate the headphone jack, it's always halfway unplugging if it's barely jostled or touched. It's the one thing I can't stand about this phone design...for awhile I wanted to return it, but T-Mobile doesn't have a phone I'd rather have, haha.
Sent from my HTC_Amaze_4G using Tapatalk 2
eliasadrian said:
I hate the headphone jack, it's always halfway unplugging if it's barely jostled or touched. It's the one thing I can't stand about this phone design...for awhile I wanted to return it, but T-Mobile doesn't have a phone I'd rather have, haha.
Sent from my HTC_Amaze_4G using Tapatalk 2
Click to expand...
Click to collapse
Yeah, lol. At least the good thing about the headphone jack is that the jack is really tight so it keeps the headphones in. I'm just hoping that the jack doesn't loosen up over time.
Sent from my HTC Amaze 4G using Tapatalk 2
stereo jack hulk strength
skugpezz said:
I agree. When I got my amaze I was goign to return it thinking the headphone jack was broken. After an hour I realized I had to apply hulk strength to get it in properly.
Click to expand...
Click to collapse
lol hulk strength, nice. made me laugh. You're right though, anyone having suspected probs with the stereo jack should try to jam it in there. I was about to get a warranty exchange and be without a phone for 3 weeks. I read this forum, and used my hulk strength to jam the jack in there. My case was also slightly making teh jack not all the way go in.
Works okay now, thanks for sharing!
shiftylock said:
I have a similar problem. The headphone jack is so tight that if I plug it in my stereo at home or in the car, it will randomly make a pop sound and stop playing music if I so much as touch it. Very irritating. It doesn't do that with headphones, but the jack is so small that I have to cram my headphones in haha. Then again, we should be thankful it's tight and not loose and awful like my old SGSII...
Click to expand...
Click to collapse
Hey, I know this is old, but my phone does the same thing. I always plug it into my FM transmitter while in my car, but if I spin the 3.5mm cord around in the jack (which I got used to doing, being a very fidgety person), it stops playing immediately. Is this what you've experienced? Has anyone found any information on it?
Thanks.
The headphone jacks at first are a bit stiff but after listening to music so much, they actually loosen up. It takes time to break it in. I don't think it will get too loose though unless you damage the phone.
Sent from my HTC_Amaze_4G using xda app-developers app
sound Jack ...!
Hi everyone. Urgent replies are more appreciated. I'm having a bit issue regarding to head phone jack. All appeared just yesterday night . Now whenever I plugged in headphone I have to continuously push it to b able to listen from both ear pieces otherwise after simply putting in like normally v do , only left earpiece is working. Plz tell. What to do. Its X715e unlocked version. Plz tell. But if I plug it in half way just when headphone sign shows it is working fin but when I completely plug in so it works only with left earpiece. While another head phone HTC desire c .that is working fine and nice.
Make sure you don't have lint in it if you do a safety pin works wonders with a flashlight. Still don't work. Like in mine get different headphones. The stock iPhone headphones keep the connection but my other zagg headphones seems the plug is to long and doesn't keep a connection very tight. Only happens with headphones that have microphones. Hope that helps.

Audio issue via AUX connection

Whenever I connect my phone to my car stereo via AUX, I'll have to unplug/re-plug the cable multiple times for it to register. Basically, it'll continue to play through the phone speaker(s) instead of coming through the stereo. I've tried multiple music players & even tested the cable itself on my old Rezound & iPod and it's working fine with them(it's not the cable).
Is there some setting to fix this?
May sound stupid, but do you have a case that may be keeping the plug from going all the way in.
Sent from my HTC6435LVW using xda app-developers app
there are no stupid questions here my friend.
and no, it's a soft case with enough room around the jack. the cable plugs in securely.
When mine is connected with no case I get a constant fuzzy static noise unless I hold the side where the red grill is then it goes away
What Rom are you running? Is it stock unrooted or a custom Rom, if rooted what kernel are you running?
Sent from my HTC6435LVW using Tapatalk 2
I should have mentioned... just got the phone a few days ago. It's still stock everything(haven't bothered unlocking/rooting/etc yet)
I had this same issue two months back. I did two things, i don't remember which did it.
Take a cotton swab and put a tiny bit of rubbing alcohol on it. Stick it in the aux port. Don't overuse the alcohol. Next, blow into the aux port. I had a small hair inside the port, causing the headphone jack/aux to not register.
I tried flashing several roms before i found out the simple issue lol. Let me know if this helps, my friend.
I had this problem and then I took the ota and it disappeared...
Sent from my HTC6435LVW using xda app-developers app
kushmacdaddy said:
I had a small hair inside the port, causing the headphone jack/aux to not register.
Click to expand...
Click to collapse
I think this is it. My phone did it yesterday and today. Both times I unplugged it, blew in the aux hole and on the stereo cable, and then it worked. Probably small piece of hair or dust in there.
This shouldn't be a problem with a new phone, but on previous phones/mp3 players I owned (ones that actually fit into a pocket) I ended up having to clean the inside of the aux plug with a paper clip (or any small thin object that wont break in there) from all the pocket lint that gathered in it.
well i tried cleaning the slot but it didn't help.
i have noticed that if i leave the screen on, plug in the cable & wait a few seconds, it registers.
any other way and it doesn't really work well/at all.
I just had this problem happen to me too...
My headphone jack has been fine since I bought the phone on release day, well yesterday after a walk, I pulled the headphone plug from the jack and noticed my music was still playing but through the phone speaker... weird.
well in my friends car I wanted to use her aux input and it didn't register (aka show the headset icon in status bar), nor did it play through the car, only the phone speakers...
same thing when I tried in my car. Also tried again with the iBeats I used when it first happened... nothing.
I tried the cotton swab thing (most cotton swabs are too think though xD) and used compressed air to blow any hairs or specs out of it...
I can get headphones to register now, but I have to plug it in veerryy sloowwllyy ... :/
thing that sucks is I don't have a warranty... I mean maybe the stock HTC one but no verizon or 3rd party warranty

Categories

Resources