UPDATE: Nothing worked, finally went to service center and they changed motherboard , it took 8 days but my ray is back #THANKUWARRANTY
This thread is not a question thread, i am posting here to warn all xperia ray users.
My Story:
Yesterday i installed ICS Pureness rom but i didnt used sirkay kernel with that instead i used .431 stock kernel (I think here is the problem).
After that i used it 20-30 mins and went back to stock .62 GB using flashtool.
I got news that stable CM9 is available, so i installed latest stable Cyanogenmod9 (cm-9.0.0-urushi.zip downloaded from official CM site), used it 5-10 mins
I dont like it either so i returned to GB .62 using cwm backup made before installing CM. Everything worked fine but my phone was not charging , just showing that its charging.
That time battery percentage was 12% it was constantly decreasing although phone was showing its charging. After few mins it turned off and i tried to turn on but phone didnt started , red led blinked 3 times and went off.
I tried another battery and phone works fine but battery still not charging. (it is showing charging but battery percentages are decreasing)
I Also charged my old battery with other phone and tried still no luck phone is unable to charge battery.
I flashed .62 firmware again , still no luck
Left my phone in charging around 5+ hours, still not charging.
Since my phone is unable to charge battery , i am charging it using a direct battery charger, by 15 mins of charging it gives me 10-12% battery. (this is only way to boot my phone and test repairing methods)
UPDATE: Tried method by emosis , Flashed stock .431 using flashtool then flashed sirkay's XRay V7.3.431 kernel but still no luck
These guys are facing same problem too.
1. http://forum.xda-developers.com/showthread.php?t=1808552
2. http://forum.xda-developers.com/showthread.php?t=1831935
Note: I think its software problem but i dont know how to fix it. Basically i am stuck.
So ray users you have been warned , dont try stable CM9.0 over .62 GB firmware otherwise you will lose your phone.
Dont forget to share to aware users, its a very big problem and If you have any suggestion please reply (#seriously so we can make this thread helpful)
If there is really no way To fix it, then maybe get one of these?http://pages.ebay.com/link/?nav=item.view&id=320777472336 I got one and love it. Comes in handy.
Sent from my PARANOID ANDROID
xperia ray said:
Note: I am 1000% sure its software problem but i dont know how to fix it , f**k you sony and Cyanogenmod team.
Click to expand...
Click to collapse
Bravo for the beautiful language. Punks like u dont deserve any help whatsoever.
Bro
Try to do what i say..
Use a charged battery..
Put out battery 1 minute.. Then turn on phone and get fastboot screen and flash sirkay latest kernel 2 times..when flash finished turn off phone and again put out battery 1 minutes turn on phone and get recovery screen - fastboot screen - flash sirkay kernel again.. then turn off phone disconnect phone from computer and connect it to charger after see charging screen turn on ur phone normally and say us the result
Are you talking about this kernel ?? = http://forum.xda-developers.com/showpost.php?p=29739291&postcount=1962
For your information= My phone is currently on GB .62 stock (i charged my phone battery separately without phone >> reinserted battery >> flash .62 stock using flashtool)
EDIT: Tried sirkay kernel not working.
When things go totally out of hand, I usually reinstall the stock ROM with Sony Ericsson Update Service with "software update+factory reset: option. In 99.5% cases it works.
(Well it might not be helpful if it SEUS does not recognize phones with unlocked bootloader.)
Its ok do it with sirkay latest kernel and install pureness you used before bro.. factory reset wipe data and dalvik cache..
Sent from my ST18i using xda app-developers app
tintin100 said:
When things go totally out of hand, I usually reinstall the stock ROM with Sony Ericsson Update Service with "software update+factory reset: option. In 99.5% cases it works.
(Well it might not be helpful if it SEUS does not recognize phones with unlocked bootloader.)
Click to expand...
Click to collapse
Problem is beyond that, i installed stock rom using flashtool but not working.
emosis said:
Its ok do it with sirkay latest kernel and install pureness you used before bro.. factory reset wipe data and dalvik cache..
Sent from my ST18i using xda app-developers app
Click to expand...
Click to collapse
Thanks a lot for your reply, i am downloading pureness again , actually deleted it.
If you can also explain why you are saying to use pureness rom ?? any technical reason behind it ??
No i said that cuz i thought u have it.. but do this :ut out battery 1 minute then recovery menu and fastboot mode use fastboot mode for flashin the kernel 2 times and put out battery again 1 minute then turn on recovery screen factory reset and wipe dalvik cache and install the rom and restart phone and say result i did this to solve mine and it worked ( dont reset battery stats)
Sent from my ST18i using xda app-developers app
@emosis bro , i am booting to fastboot like we normally do (switch off phone>>hold volume up and connect to pc)
is there any different method too, as you are saying - "recovery menu and fastboot mode"
I also tried , booted in recovery then selected reboot in fastboot mode but phone started normally.
Thanks a lot.
Note: I am not a noob, in fact a developer kinda geek, but this problem made me sick and tired , i surrendered. seems like hardware problem.
If possible please tell me what happened with your phone, did you faced exact problem like i did ?
In sirkay kernel reboot in fastbootmode or while using phone settings application develop usb debugging on..and use flashtool reboot in fastboot mode phone led must be blue.. if it s ok flash the kernel 2 times and do what i said bro.
Sent from my ST18i using xda app-developers app
flash .72 baseband and reflash xkernel v7.3.431 again
sirkay said:
flash .72 baseband and reflash xkernel v7.3.431 again
Click to expand...
Click to collapse
i flashed .431 so it have .72 baseband already. Should i flash xkernel v7.3.431 once more ?
yes, then go into recovery
- wipe data / factory reset
- wipe dalvik-cache
- wipe battery stats
- flash rom
- boot into rom
Strange, I had no problems when going back to .62 from CM9 stable...
I've heard that you can wipe EVERYTHING from the phone memory, leaving only basic programs and protocols like flashmode and fastboot by taking the battery out and charging the phone without for some time. Maybe it should help, though I never used this method and I don't know if it's safe or will it ever work...
I had battery %0 problem before can't charge phone.. i had it cuz battery stats was so low i flashed a kernel and used clear battery stats and installed a new rom.. ...... tried many thing to solve so i solved this problem the way i explained..hope you can solve it too..
Sent from my ST18i using xda app-developers app
emosis said:
I had battery %0 problem before can't charge phone.. i had it cuz battery stats was so low i flashed a kernel and used clear battery stats and installed a new rom.. ...... tried many thing to solve so i solved this problem the way i explained..hope you can solve it too..
Sent from my ST18i using xda app-developers app
Click to expand...
Click to collapse
my phone is not showing 0% all the time, it shows 10-11% battery and when i connect it, instead of charging it start to discharge.
Since my phone is unable to charge battery , i am charging it using a direct battery charger, by 15 mins of charging it gives me 10-12% battery. (this is only way to boot my phone and test repairing methods)
So could you try the way i said?
Sent from my ST18i using xda app-developers app
sirkay said:
yes, then go into recovery
- wipe data / factory reset
- wipe dalvik-cache
- wipe battery stats
- flash rom
- boot into rom
Click to expand...
Click to collapse
tried but not working, i think its hardware problem in phone. (Except charging battery everything is working fine)
Battery is working (i charge it using external charger)
Related
So i was trying to flash basebrand .55 from basebrand .54 onto my x10 using the 0.2.9.1 flashtool and then it said error turn on usb debugging. When i go to turn it on my phone doesnt start back up. I tried flashing the 2.1.1.435 firmware to see if i could fix it somehow but it gets stuck on "Flashing loader" then says to turn on usb debugging? Am i screwed here. I cant boot my phone!
Try doing a repair through SEUS. It will say that you have the latest firmware, but install it anyway.
just reflashed the basebrand again. It seems to work now? Thank goodness it it did bc SEUS couldnt read it. Thank you though =)
Hmmm....everything is working smoothly...but my battery is increasing slowly? instead of decreasing(it is not plugged in!)...should i be concerned i just wiped battery stats and its still increasing
It's a glitch that will correct itself, once your battery gets to its actual level it will start to decrease again.
Sent from my X10i TripNMiUI using XDA Premium App
Try wiping battery stats via x recovery.
aval1392 said:
Hmmm....everything is working smoothly...but my battery is increasing slowly? instead of decreasing(it is not plugged in!)...should i be concerned i just wiped battery stats and its still increasing
Click to expand...
Click to collapse
Sent from my Xperia Arc using XDA Premium App
So, sort of long story, i'll cut it short
-Got an old X10, had stock 2.3.3
-Rooted it
-Did not unlock bootloader, got kinda scared.
-Tried to install FeraLab custom ROM, it failed probably because of sdcard permissions; i accidentally wipe /system /data /cache
-stuck at first Sony Ericsson screen
-Somehow managed to flash a 2.1 stock rom with flashtool, after an hour of different combinations of enterring flash mode and pulling the battery
-Tried to install FeraLab again, this time it went through
-After install, rebooted, phone shut down during boot up process
-Will not turn on at all. Even when plugged into a PC, wall, not plugged in, pulling battery, etc.
I think what happened is that FeraLab needed a newer baseband than the 2.1 stock rom had. Does anyone have any suggestions on how to get this sucker to even turn on? Not a single LED is on when plugged in, giving me the impression that it's not charging.
If the battery has drained out, it might take some time before it kicks in and indicates that it is charging.
If the ROM has failed somehow, it might not show that it is charging at all, but might be charging.
Either way: Let it charge "blindly" for a while, and see what happens.
Once it does boot up to some level or shows life-signs, let it charge fully before you'l attempt a ROM flash.
The flash/recovery mode needs a full battery, and reason is that the external power isn't used even when connected while in flash/recovery mode.
If you happen to be in bad luck, and the ROM failed as a result of a drained battery, you might have to charge the battery externally. Use an external battery charger made for 3.6 volts Lithium Polymer batteries, and make sure to align the + and - terminals properly.
I can recommend the multicharger from Powerbase, called C-734U:
http://www.powerbasehk.com/product.php?id=148
Using it myself to charge the X10 battery, as well as other batteries from other devices I have.
EDIT:
(For some reason, powerbase has taken back that it'll charge Lipo batteries, but when I bought mine, it was described as a li-ion, li-poly and Ni-MH charger, and it't ability to charge li-poly batteries was the very one reason to why I bought it.
I suspect PowerBase does not want to take responsibility if anything happens to the li-poly-batteries, as they are known to be more dangerous than other types.)
I've left it on the wall charger all night, no response or anything. Luckily, I bought a new battery a few days ago, so when that comes in, hopefully it will be charged enough for this thing to boot.
Do me a favour are u able to take screebshot of settings, about phone menu and post it here? Need to see ur baseband and kernel
Sent from my X10i using XDA
laneyofdeath said:
Do me a favour are u able to take screebshot of settings, about phone menu and post it here? Need to see ur baseband and kernel
Sent from my X10i using XDA
Click to expand...
Click to collapse
Dude his phone wont start up. How come he'll be able to take a screenshot
Sent from my LT26i using xda premium
king-iyokan said:
Dude his phone wont start up. How come he'll be able to take a screenshot
Sent from my LT26i using xda premium
Click to expand...
Click to collapse
Yeah, i'm not sure what he expected. But, good news! Now for some reason my phone started blinking red whenever I tried to turn it on! I guess the battery completely ran out or something. It also blinks every now and then when plugged in, so I guess it's charging. The previous owner of this phone said that it had some battery problems, so that's why I ordered that new battery. I'll let it charge for awhile and let you guys know what happens.
Okay, after getting my new battery, the phone will still not turn on. I think i've figured out two behaviors:
1. If the battery is nearly completely out of charge, it will flash a red light
2. If the battery has charge, it will not do anything at all.
Anyone know how to fix this?
While trying to turn on the phone, after long-press power button, do you get a flash from status led & short vibration?
From my XPERIA X10S v8.2 on kCernel @ 1.19ghz
ToledoJab said:
While trying to turn on the phone, after long-press power button, do you get a flash from status led & short vibration?
From my XPERIA X10S v8.2 on kCernel @ 1.19ghz
Click to expand...
Click to collapse
No vibration, the red LED flashes three times, and that is , as I said before, what happens when the battery seems to not have any charge. If I have a charged battery it does absolutely nothing.
Have you removed sim & sd card and tried. I know it sounds dumb but when I flashed a bad kernel I had to try to connect flash mode like 10 times. Finally I left the phone unplugged from pc, started flashtool and started flashing. I only put battery in phone just before holding back key. I never connected USB until tool said to dis-connect phone and connect in flashmode.
i wish you luck, I know how I felt when it went wrong
From my XPERIA X10S v8.2 on kCernel @ 1.19ghz
FireFreek said:
So, sort of long story, i'll cut it short
-Got an old X10, had stock 2.3.3
-Rooted it
-Did not unlock bootloader, got kinda scared.
-Tried to install FeraLab custom ROM, it failed probably because of sdcard permissions; i accidentally wipe /system /data /cache
-stuck at first Sony Ericsson screen
-Somehow managed to flash a 2.1 stock rom with flashtool, after an hour of different combinations of enterring flash mode and pulling the battery
-Tried to install FeraLab again, this time it went through
-After install, rebooted, phone shut down during boot up process
-Will not turn on at all. Even when plugged into a PC, wall, not plugged in, pulling battery, etc.
I think what happened is that FeraLab needed a newer baseband than the 2.1 stock rom had. Does anyone have any suggestions on how to get this sucker to even turn on? Not a single LED is on when plugged in, giving me the impression that it's not charging.
Click to expand...
Click to collapse
Try to flash any latest kernel via flashtool . Go for doomkernel . I think its software issue . Try this first .
Almost same here please help..
Last night battery ran out of charge & phone switched off.. then i plugged the charger it doesn't charge.. after some time i tried turning on.. Vibrates with the green LED but nothing happens then..
Note: This is not the 1st time i'm letting my phone drain, but facing this problem for the 1st time..
Rom : Spikelabs GB Gaming rom
Kernel : Ferakernel v23 beta6
I tried another battery, charger, data cable.. Tried flashing stock & spikelabs kernel., but of no use..
Any help is greatly appreciated..
Thanks in advance.. :good:
Something like that happened to me not long ago!
I was trying to flash some ROMs and I messed up then my phone wouldn't turn on!
But Miracously, I could flash a Stock 2.3.3 which fixed the problem!
At first, I used Sony PC Companion, which helped a lot- and after I screwed it for the second time, I used FlashTool-
I don't know if this was helpful, but I hope your x10 will be fixed soon!
yeah try the PC Companion first, it helped me too a couple of weeks ago
No luck...
Hi friends..
Tried to repair using PC companion, but was able to connect only in flash mode, unable to proceed software update..
I previously tried flashing stock GB using flashtool thrice. Still couldn't switch on the phone.. What else may i try..
Thanks friends..
ashok weird said:
Hi friends..
Tried to repair using PC companion, but was able to connect only in flash mode, unable to proceed software update..
I previously tried flashing stock GB using flashtool thrice. Still couldn't switch on the phone.. What else may i try..
Thanks friends..
Click to expand...
Click to collapse
try flashing kernel other than spikelabs (e.g. feravolt,doom,achotjan,zkernel..etc.)
sanababitz said:
try flashing kernel other than spikelabs (e.g. feravolt,doom,achotjan,zkernel..etc.)
Click to expand...
Click to collapse
Tried Ferakernel, Stock GB kernel, etc bro.. No luck..
Flashed Stock GB firmware more than 3 times still no luck :crying:
SEUS not working _ couldn't connect to network..
SUS does not have x10 enlisted
Went to 3 service shops at - Ritchie street, Chennai. They simply said harware issue (Short in board) and gave back the phone.
Now given at a better service centre. Will get back on monday it seems. Will update the status friends..
Thanks..
Here also they said the same reason friends.. Short in board..
Is there any way i could recover the phone???
Hi there. First of all, sorry about my english, but i'm spanish
I was reading a lot, and i cant find a solution to my phone. It sudently becomes a brick just when charging (with anothers phone charger) and the battery was lower than 10%
It doesn't work, and don't response to any of all solutions i've read (Take out SIM, SD card, remove battery and wait... ) no way... Screen never come back to iluminate again. Just, when pushing power buttom, the phone's vibrates.
So tired of the brick, i've arrived at this page. And I read this post:
http://forum.xda-developers.com/showthread.php?t=1568792
And try to become my phone back...
At least, the phone enter in flashmode, and i can flash with flashtools... but the phone never come back... just the brick
I tryed to flash with the Xperia_2011_FreeXperia_ALL.ftf file and OK
Afther that, take out the USB and flash again with one ROM i get from here:
Xperia Mini Pro (SK17i)
4.0.2.A.0.42 - http://www.mediafire.com/?hevz3x5w9pqt24q
4.1.B.0.431 - http://www.mediafire.com/?j0bdx06zz5skvzt
But the phone never works. One time afther flashing with 4.0.2.A.0.42 i noticed, that trying to power on the phone, the red led shyne 3 times, and thats supposed to be the battery. But i don't know if the battery now is charged. I've left it hours charging, and hours too to the USB...
Supposedly, i cant flash without battery in the phone, but flashtools finish correctly
So... any idea?
There is something i can do?
Thank all of you who read this!
Its probably battery empty. recharge battery or get a friends and try
Sent from my X8 using Tapatalk 2
First make sure that your battery is really fine. Try another one.
If that fails, see if you can get your device into flash mode?(Switched off+Vol Down + USB cable)
If yes, try flashing a custom ROM. For example, download CyanogenMod from here, use Flashtool (guide) to flash the kernel provided in the downloaded ROM's ZIP file. Then, boot again into Clockword Mod Recovery(Keep pressing Vol DOwn button while boot or google for how to enter recovery for your phone). Copy the downloaded Cyanogenmod ZIP to SD card and install it via ClockwordMod recovery.
See if the above works.
bandarigoda123 said:
Its probably battery empty. recharge battery or get a friends and try
Sent from my X8 using Tapatalk 2
Click to expand...
Click to collapse
But, if it was problem of battery, i suppose, that i can't finish flashing with flashtoolts. Not?
Milven said:
But, if it was problem of battery, i suppose, that i can't finish flashing with flashtoolts. Not?
Click to expand...
Click to collapse
Try booting up your phone with the USB connector plugged in the PC (maybe it will charge the battery then)
Milven said:
But, if it was problem of battery, i suppose, that i can't finish flashing with flashtoolts. Not?
Click to expand...
Click to collapse
At least my phone (LWW WT19i does not work without the battery with Flashtool. I'm not sure about your device.
Anyway try flashing a custom ROM like I said. Try unlocking bootloader first though from here
U said that red light show when try to on the phone.
Just try another battery.. It should work
Sent from my X8 using Tapatalk 2
You said LED blinks 3 times so if the color of LED is RED then it indicates empty battery..
Hey, my problem wasnt the same as yours, but it helped for me when i got only service logo on screen.
On this link you find a "Play_v1.01_TA brick fix UPDATE" zip.
Download, unpack and flash it.
http://forum.xda-developers.com/showthread.php?t=1126358&page=10
I hope it will help u.
Milven said:
Hi there. First of all, sorry about my english, but i'm spanish
I was reading a lot, and i cant find a solution to my phone. It sudently becomes a brick just when charging (with anothers phone charger) and the battery was lower than 10%
It doesn't work, and don't response to any of all solutions i've read (Take out SIM, SD card, remove battery and wait... ) no way... Screen never come back to iluminate again. Just, when pushing power buttom, the phone's vibrates.
So tired of the brick, i've arrived at this page. And I read this post:
http://forum.xda-developers.com/showthread.php?t=1568792
And try to become my phone back...
At least, the phone enter in flashmode, and i can flash with flashtools... but the phone never come back... just the brick
I tryed to flash with the Xperia_2011_FreeXperia_ALL.ftf file and OK
Afther that, take out the USB and flash again with one ROM i get from here:
Xperia Mini Pro (SK17i)
4.0.2.A.0.42 - http://www.mediafire.com/?hevz3x5w9pqt24q
4.1.B.0.431 - http://www.mediafire.com/?j0bdx06zz5skvzt
But the phone never works. One time afther flashing with 4.0.2.A.0.42 i noticed, that trying to power on the phone, the red led shyne 3 times, and thats supposed to be the battery. But i don't know if the battery now is charged. I've left it hours charging, and hours too to the USB...
Supposedly, i cant flash without battery in the phone, but flashtools finish correctly
So... any idea?
There is something i can do?
Thank all of you who read this!
Click to expand...
Click to collapse
Hi Milven,
I got the same problem with you yesterday. Few hours sitting in front of my PC and hopeless.
I tried everything same as yours, finally I found and solve the case.
Install this http://www.sonymobile.com/global-en/tools/update-service/
And let it update your phone.
Done. It's back to brand new.
Hope you read this.
frdnoer said:
Hi Milven,
I got the same problem with you yesterday. Few hours sitting in front of my PC and hopeless.
I tried everything same as yours, finally I found and solve the case.
Install this http://www.sonymobile.com/global-en/tools/update-service/
And let it update your phone.
Done. It's back to brand new.
Hope you read this.
Click to expand...
Click to collapse
That's true. Try fixing it by using sony repairment. I did it and it worked for my phone. I hope it does for you
Sent from my Xperia, Asri Aisyah El Zahra
i've the same problem as you. charge your battery with desktop charger. not too long, i put the battery and flash firmware in flashtool. and it work. when the flashing done and the device on, my battery just 3% lol. flashing with flashtool only takes a few minutes
I have Neo V, Unlocked Bootloader, Suave v6 kernel, Xperia Ultimate HD Rom.
Battery Discharges while charging... It shows charging but it does not it drains as usual.
Tried wiping battery stats. (No Success)
Tried reflashing rom. (No Success)
Tried changing kernel and rom as a fresh install... (No Success)
Then tried Battery Calibration App (NO Success)
Charger works fine tried on Xperia Ray.
One solution that works is by restoring cwm backup, then it charges... So the problem is when ever i want charging i need to restore from cwm
What may be the problem ????:crying:
Did u try to flash stock ics firmware with full wipe?
Sent from my MT11i using Tapatalk 2
Samak46 said:
Did u try to flash stock ics firmware with full wipe?
Sent from my MT11i using Tapatalk 2
Click to expand...
Click to collapse
nope. will I lose root???
can I flash stocl firmware with custom kernel that is suave kernel and can I flash stock after 0% battery after switched off also???
Yes, you'll loose root. But if the battery is 0%, flash will not work.
session20 said:
nope. will I lose root???
can I flash stocl firmware with custom kernel that is suave kernel and can I flash stock after 0% battery after switched off also???
Click to expand...
Click to collapse
Yes u will loose root..
Nope, u cant flash after battery got died..
Do one thing, restore nandroid & charge ur phone to minimum 50%, then flash stock ftf using flashtool with full wipe..
Sent from my MT11i using Tapatalk 2
Samak46 said:
Yes u will loose root..
Nope, u cant flash after battery got died..
Do one thing, restore nandroid & charge ur phone to minimum 50%, then flash stock ftf using flashtool with full wipe..
Sent from my MT11i using Tapatalk 2
Click to expand...
Click to collapse
Flashing stock ftf also No sucess. Now it doesn't charge all last
I have lost root and now cant go to nandriod...
How to root... now.... and have unlocked booloder.
session20 said:
Flashing stock ftf also No sucess. Now it doesn't charge all last
I have lost root and now cant go to nandriod...
How to root... now.... and have unlocked booloder.
Click to expand...
Click to collapse
What if told you that you are now need to change the battery
Saingpor said:
What if told you that you are now need to change the battery
Click to expand...
Click to collapse
I have tried that too... my cousin has xperia ray which has BA 700 same as Neo V BA 700 so replaced my neo battery to ray and ray battery to Neo....
So the results are now the neo battery that was not charging its now charging in ray and ray battery which in neo not charging, and shows wrong percentage..if 64% in neo then replacing to ray it show 57% and the ray which was 28% now shows 33% in my neo...
session20 said:
I have tried that too... my cousin has xperia ray which has BA 700 same as Neo V BA 700 so replaced my neo battery to ray and ray battery to Neo....
So the results are now the neo battery that was not charging its now charging in ray and ray battery which in neo not charging, and shows wrong percentage..if 64% in neo then replacing to ray it show 57% and the ray which was 28% now shows 33% in my neo...
Click to expand...
Click to collapse
Have to try a soft cloth cleaning the battery pin ? Or else go to service center :silly:
What abot replacing charging cable or charger? My friend has issue with galaxy s3. He replaced cable and now all is ok.
Sent from my GT-I9300 using xda app-developers app
Saingpor said:
Have to try a soft cloth cleaning the battery pin ? Or else go to service center :silly:
Click to expand...
Click to collapse
As i have unlocked bootloader will they accept for paid service...
But i don't understand after restoring to cwm backup its charging like normal and after using some battery percentage then again i plug the charger then it doesn't charge.
Again when i restore to cwm backup then again it charges...
b1tux said:
What abot replacing charging cable or charger? My friend has issue with galaxy s3. He replaced cable and now all is ok.
Sent from my GT-I9300 using xda app-developers app
Click to expand...
Click to collapse
Ray charges fine with the charger presently using.
session20 said:
As i have unlocked bootloader will they accept for paid service...
But i don't understand after restoring to cwm backup its charging like normal and after using some battery percentage then again i plug the charger then it doesn't charge.
Again when i restore to cwm backup then again it charges...
Click to expand...
Click to collapse
Just relock the bootloader using relock bootloader ftf file, then goto service center... Its maybe a hardware issue...
Sent from my MT11i using Tapatalk 2
Samak46 said:
Just relock the bootloader using relock bootloader ftf file, then goto service center... Its maybe a hardware issue...
Sent from my MT11i using Tapatalk 2
Click to expand...
Click to collapse
Can u provide link to relock bootloader ftf file.. I actually unlocked bootloader with official sony method.
Hey mate
Just try another rom. U wont get that battery discharging while charging. Try a simple rom not the rom which u currently using. If u use uhd suppose try another rom like pureness, supernova etc jst some simple rom and then see. A friend of mine had flashed latest uhd 3.0.2 he also noticed the same thing. He flashed pureness and everything is alrite now.:good:
session20 said:
Can u provide link to relock bootloader ftf file.. I actually unlocked bootloader with official sony method.
Click to expand...
Click to collapse
IF you ever want to relock your BL ! Then here is a tut :
1.You must have flashtool installed !
2.Download this ftf http://www33.zippyshare.com/v/61382627/file.html
3.Once download done ! Copy that ftf to Flashtool/firmwares
4.Open flashtool and select the lightning icon and select flashmode and then select Xperia Relock BL and hit enter
5.Now turn off your device and hold back key and connect it to your PC
6.Wait till finish
7.Done
Now you have your BL Relock but still your drm lost
koradiavatsal said:
Hey mate
Just try another rom. U wont get that battery discharging while charging. Try a simple rom not the rom which u currently using. If u use uhd suppose try another rom like pureness, supernova etc jst some simple rom and then see. A friend of mine had flashed latest uhd 3.0.2 he also noticed the same thing. He flashed pureness and everything is alrite now.:good:
Click to expand...
Click to collapse
I tried that too... but not the roms u mentioned. I tried Zelly cream and smart xperia rom and Xperia T v7.0.2 all got same problem...
But today morning flashed stock .587 ftf and then flash suave v6 kernel then rooted, restored the cwm backup ie UHD then charged to 100% then used battery calibration app from playstore.
waiting for complete discharge or atleast till 12-20% then will try recharging. Hope it works.. :fingers-crossed:
Will respond after battery discharge and trying to recharge..:fingers-crossed:
Can you tell how much time does its takes 1% battery drain when idle for example 90% to 89% how many minutes does it takes for you all.
For me it takes approx5-6 mins as I use my phone too heavily.
Try ice cream pureness rom use normally dont flash any mods. And see the drain. Theres an app called battery repair as suggested by some one I read I never tried bt will soon. U can try.
Recharge to 100% full after phone gets off. Charge at a strech from 0% to 100%
koradiavatsal said:
For me it takes approx5-6 mins as I use my phone too heavily.
Try ice cream pureness rom use normally dont flash any mods. And see the drain. Theres an app called battery repair as suggested by some one I read I never tried bt will soon. U can try.
Recharge to 100% full after phone gets off. Charge at a strech from 0% to 100%
Click to expand...
Click to collapse
and now phone charged up to 100% at around 3:00PM and now 7:45PM it is to 80% after a 2 min call and then some 5-10 mins of gameplay and then few slides in settings and homescreen checking time frequently that is pressing power button to look at the time and then pressing again to sleep.
it took 20% of battery in 4 hours 45 mins... is this normal??? One more thing i checked it takes 1% of battery 15-20 mins in idle.
and about completely discharge i have a fear if it goes completely 0% then i cant get cwm backup to recharge again if does not charge after complety discharge.
Here a solution. Ever tried this fact. Remove ur battery. Connect charger to phone dont insert battery. It will boot up without battery bt as soon as u disconnect ur charger it will switch off. So dont worry ur phone will always charge even if its 0% and do u do too much flashing/rebooting? If yes 15-20 mins ideal state 1% drain is normal. Bt bro stop flashing too much. Chose a rom and stay on it fr a period of time say 2-3 weeks. One more tip: let ur phone discharge to 0% till it switches off and charge till 100% at a strech then use ur phone nd occasionally say in a week when phone is charged fully cwm> wipe battery stats .. In dis way maybe in a month or two u wont hv battery problems
Hi
Today my XZ2 gone very hot and battery drained from 100% to 30% in 3 hrs. So i decided to make factory reset and.. Phone turned off and nothing. Flashmode was working so I tried to flash rom via flashtool. Tried 23.5.A.0.575 Customized_NCB and... stuck at flashing data (system.sin). I was waiting for 30 minutes and then decided to shut down flashtool. Second attempt is 23.4.A.1.264 Customized CE1. Now FlashTool stucks at reading device information. What's going on? Plz help...:crying::crying:
Have you updated to the latest flashtool? There's a note in the changelog:
* 0.9.22.1
Bad compute of maxpackesize (hangs on some sin files)
System was where it hung on me as well and after updating I flashed .575 with no problem.
Bruce666 said:
Hi
Today my XZ2 gone very hot and battery drained from 100% to 30% in 3 hrs. So i decided to make factory reset and.. Phone turned off and nothing. Flashmode was working so I tried to flash rom via flashtool. Tried 23.5.A.0.575 Customized_NCB and... stuck at flashing data (system.sin). I was waiting for 30 minutes and then decided to shut down flashtool. Second attempt is 23.4.A.1.264 Customized CE1. Now FlashTool stucks at reading device information. What's going on? Plz help...:crying::crying:
Click to expand...
Click to collapse
Why did the phone turned off and nothing after factory reset?
i think it is related to the battery. have you charged the phone before using flashtool.
maybe the main issue for the drain was the battery itself and not software related. and if so the battery could drain when using flashtool which isn't recognizing the phone now as it is stuck on reading phone information
michel090428 said:
Why did the phone turned off and nothing after factory reset?
i think it is related to the battery. have you charged the phone before using flashtool.
maybe the main issue for the drain was the battery itself and not software related. and if so the battery could drain when using flashtool which isn't recognizing the phone now as it is stuck on reading phone information
Click to expand...
Click to collapse
It was about 70% during resetting. I put it on charger and after an hour conected to flashtool. Now works, I downloaded KitKat 4.4.4 and everything works fine. Seems that downloaded files were corrupted. thanxx for help