Related
I tried to install a custom rom on my x10 mini using x recovery and the phone fully rooted, I downloaded a 2.2 custom rom to my sd card entered xrec and after backing up my stock rom installed the new one, when finished the phone shut down automaticly and restarted but froze on the white sony ericsson logo (writing only no image) for about 30 seconds or so then shut down and restarted, and the same again and again untill battery is drained. I tried to use seus but it gets to about 49% then says failed , I then tried flash tool wich tries to send the first file and frezzez until I unplug the phone and I am still left with the same problem this also happens when I try to charge the phone. Please please please can somebody help I will be most greatfull thanx
Sent from my U20i using XDA App
That is called a bootloop, so first use SEUS in order to restore the original SE eclair and then try again.
Forgive me if I'm wrong but, isn't your phone a Mini Pro, 'cause your tapatalk signature says U20i and that's a Mini Pro, if it is you gotta download a Mini Pro ROM, a Mini ROM won't work on your phone.
No my friend diffrent phone the x10 mini wont do anything and for some reason I can put the phone in flash mode and use SEUS but it says failed when it reaches 49%. So I cant restore the stock rom. Any other ideas would be helpfull and I shall try SEUS again thanx
Sent from my U20i using XDA App
I have faced exactly the same problem in my x10 mini. What I done is, drained the battery that the phone can be switched off, then charged the phone for 15 minute (It remains off). Then I flashed the phone with Flash Tool not SEUS. Now it is alright.
Downloading stops or installing stops?
Before flashing make following steps :
1. Full Wipe,
2. Wipe Cache Partition,
3. Clear cache,
4. Clear dalvik cache.
Then flash the Rom. It will normaly work.
Just plug in your phone with usb cable to the computer and let it charge for two or more hour . By the time you shouldn't do anything with your phone . And also dont run seus . Let the phone be charged sufficiently . During this time the phone would not turn on and you can do nothing with your phone during this time. You will only see the red led . After two hours of charging disconnect and run seus and Follow the onscreen instruction. I followed the above mentioned procedure and I got my mini back .
Sent from my X10mini using XDA Premium App
Sent from my X10mini using XDA Premium App
Thank you all its done and im now running minicm6. I had to wait quite a while for the batt to drain but it worked so thank you for all your help I just now have the problem that running minicm6 my mini will no longer recive apk files via bluetooth from my mini pro but all other file types will work. Thanx again for all your input
Sent from my U20i using XDA Premium App
Hi when i use my xperia x10 on charge the fone gets warm and reaches temp of 43 degrees what could be the problem cheers waj
yes it was my problem too before... did you factory reset or repair from PC companion or updated your rom if so you must root your phone install xrecovery and wipe batterystats.bin.. thats how i got the solution and bring to normal charging with my phone.
and also install battery calibration to calibrate your battery and phone again..
Is your phone updated to gingerbread?
If not you may have an old baseband, if so you should get it updated with the rooted version in the development area or update using SEUS or PC companion.
Nucleus55 said:
and also install battery calibration to calibrate your battery and phone again..
Click to expand...
Click to collapse
That might be the reason for the overheating, make sure you don't switch batteries on the x10, I did that recently because the USB port of a friend's phone was broken, now my battery acts all weird and when i first put my battery back into my phone it got hot aswell, for the first time ever.
Nucleus55 said:
yes it was my problem too before... did you factory reset or repair from PC companion or updated your rom if so you must root your phone install xrecovery and wipe batterystats.bin.. thats how i got the solution and bring to normal charging with my phone.
^
ok tanx mate will try and tell you what happens
and also install battery calibration to calibrate your battery and phone again
already tryed that mate thanks
TheRuan said:
Is your phone updated to gingerbread?
If not you may have an old baseband, if so you should get it updated with the rooted version in the development area or update using SEUS or PC companion.
Click to expand...
Click to collapse
i have baseband 71
Click to expand...
Click to collapse
So, sort of long story, i'll cut it short
-Got an old X10, had stock 2.3.3
-Rooted it
-Did not unlock bootloader, got kinda scared.
-Tried to install FeraLab custom ROM, it failed probably because of sdcard permissions; i accidentally wipe /system /data /cache
-stuck at first Sony Ericsson screen
-Somehow managed to flash a 2.1 stock rom with flashtool, after an hour of different combinations of enterring flash mode and pulling the battery
-Tried to install FeraLab again, this time it went through
-After install, rebooted, phone shut down during boot up process
-Will not turn on at all. Even when plugged into a PC, wall, not plugged in, pulling battery, etc.
I think what happened is that FeraLab needed a newer baseband than the 2.1 stock rom had. Does anyone have any suggestions on how to get this sucker to even turn on? Not a single LED is on when plugged in, giving me the impression that it's not charging.
If the battery has drained out, it might take some time before it kicks in and indicates that it is charging.
If the ROM has failed somehow, it might not show that it is charging at all, but might be charging.
Either way: Let it charge "blindly" for a while, and see what happens.
Once it does boot up to some level or shows life-signs, let it charge fully before you'l attempt a ROM flash.
The flash/recovery mode needs a full battery, and reason is that the external power isn't used even when connected while in flash/recovery mode.
If you happen to be in bad luck, and the ROM failed as a result of a drained battery, you might have to charge the battery externally. Use an external battery charger made for 3.6 volts Lithium Polymer batteries, and make sure to align the + and - terminals properly.
I can recommend the multicharger from Powerbase, called C-734U:
http://www.powerbasehk.com/product.php?id=148
Using it myself to charge the X10 battery, as well as other batteries from other devices I have.
EDIT:
(For some reason, powerbase has taken back that it'll charge Lipo batteries, but when I bought mine, it was described as a li-ion, li-poly and Ni-MH charger, and it't ability to charge li-poly batteries was the very one reason to why I bought it.
I suspect PowerBase does not want to take responsibility if anything happens to the li-poly-batteries, as they are known to be more dangerous than other types.)
I've left it on the wall charger all night, no response or anything. Luckily, I bought a new battery a few days ago, so when that comes in, hopefully it will be charged enough for this thing to boot.
Do me a favour are u able to take screebshot of settings, about phone menu and post it here? Need to see ur baseband and kernel
Sent from my X10i using XDA
laneyofdeath said:
Do me a favour are u able to take screebshot of settings, about phone menu and post it here? Need to see ur baseband and kernel
Sent from my X10i using XDA
Click to expand...
Click to collapse
Dude his phone wont start up. How come he'll be able to take a screenshot
Sent from my LT26i using xda premium
king-iyokan said:
Dude his phone wont start up. How come he'll be able to take a screenshot
Sent from my LT26i using xda premium
Click to expand...
Click to collapse
Yeah, i'm not sure what he expected. But, good news! Now for some reason my phone started blinking red whenever I tried to turn it on! I guess the battery completely ran out or something. It also blinks every now and then when plugged in, so I guess it's charging. The previous owner of this phone said that it had some battery problems, so that's why I ordered that new battery. I'll let it charge for awhile and let you guys know what happens.
Okay, after getting my new battery, the phone will still not turn on. I think i've figured out two behaviors:
1. If the battery is nearly completely out of charge, it will flash a red light
2. If the battery has charge, it will not do anything at all.
Anyone know how to fix this?
While trying to turn on the phone, after long-press power button, do you get a flash from status led & short vibration?
From my XPERIA X10S v8.2 on kCernel @ 1.19ghz
ToledoJab said:
While trying to turn on the phone, after long-press power button, do you get a flash from status led & short vibration?
From my XPERIA X10S v8.2 on kCernel @ 1.19ghz
Click to expand...
Click to collapse
No vibration, the red LED flashes three times, and that is , as I said before, what happens when the battery seems to not have any charge. If I have a charged battery it does absolutely nothing.
Have you removed sim & sd card and tried. I know it sounds dumb but when I flashed a bad kernel I had to try to connect flash mode like 10 times. Finally I left the phone unplugged from pc, started flashtool and started flashing. I only put battery in phone just before holding back key. I never connected USB until tool said to dis-connect phone and connect in flashmode.
i wish you luck, I know how I felt when it went wrong
From my XPERIA X10S v8.2 on kCernel @ 1.19ghz
FireFreek said:
So, sort of long story, i'll cut it short
-Got an old X10, had stock 2.3.3
-Rooted it
-Did not unlock bootloader, got kinda scared.
-Tried to install FeraLab custom ROM, it failed probably because of sdcard permissions; i accidentally wipe /system /data /cache
-stuck at first Sony Ericsson screen
-Somehow managed to flash a 2.1 stock rom with flashtool, after an hour of different combinations of enterring flash mode and pulling the battery
-Tried to install FeraLab again, this time it went through
-After install, rebooted, phone shut down during boot up process
-Will not turn on at all. Even when plugged into a PC, wall, not plugged in, pulling battery, etc.
I think what happened is that FeraLab needed a newer baseband than the 2.1 stock rom had. Does anyone have any suggestions on how to get this sucker to even turn on? Not a single LED is on when plugged in, giving me the impression that it's not charging.
Click to expand...
Click to collapse
Try to flash any latest kernel via flashtool . Go for doomkernel . I think its software issue . Try this first .
Almost same here please help..
Last night battery ran out of charge & phone switched off.. then i plugged the charger it doesn't charge.. after some time i tried turning on.. Vibrates with the green LED but nothing happens then..
Note: This is not the 1st time i'm letting my phone drain, but facing this problem for the 1st time..
Rom : Spikelabs GB Gaming rom
Kernel : Ferakernel v23 beta6
I tried another battery, charger, data cable.. Tried flashing stock & spikelabs kernel., but of no use..
Any help is greatly appreciated..
Thanks in advance.. :good:
Something like that happened to me not long ago!
I was trying to flash some ROMs and I messed up then my phone wouldn't turn on!
But Miracously, I could flash a Stock 2.3.3 which fixed the problem!
At first, I used Sony PC Companion, which helped a lot- and after I screwed it for the second time, I used FlashTool-
I don't know if this was helpful, but I hope your x10 will be fixed soon!
yeah try the PC Companion first, it helped me too a couple of weeks ago
No luck...
Hi friends..
Tried to repair using PC companion, but was able to connect only in flash mode, unable to proceed software update..
I previously tried flashing stock GB using flashtool thrice. Still couldn't switch on the phone.. What else may i try..
Thanks friends..
ashok weird said:
Hi friends..
Tried to repair using PC companion, but was able to connect only in flash mode, unable to proceed software update..
I previously tried flashing stock GB using flashtool thrice. Still couldn't switch on the phone.. What else may i try..
Thanks friends..
Click to expand...
Click to collapse
try flashing kernel other than spikelabs (e.g. feravolt,doom,achotjan,zkernel..etc.)
sanababitz said:
try flashing kernel other than spikelabs (e.g. feravolt,doom,achotjan,zkernel..etc.)
Click to expand...
Click to collapse
Tried Ferakernel, Stock GB kernel, etc bro.. No luck..
Flashed Stock GB firmware more than 3 times still no luck :crying:
SEUS not working _ couldn't connect to network..
SUS does not have x10 enlisted
Went to 3 service shops at - Ritchie street, Chennai. They simply said harware issue (Short in board) and gave back the phone.
Now given at a better service centre. Will get back on monday it seems. Will update the status friends..
Thanks..
Here also they said the same reason friends.. Short in board..
Is there any way i could recover the phone???
Okay, I was told to go here since people on AndroidForums.com had no clue on what to do.
Okay, here are my problems -
I received this Android from my mom and it was running Android 2.1. When I first got it, I turned it on without charging it. It booted up, came to the lockscreen, then about a second later turned off and now refuses to boot. I have tried flashing it with generic Android 2.1 and Stock ATT Android 2.1. But it refuses to do nothing but flashes a green light and vibrates. But that all it does. And PC Companion, SEUS, FlashTool have done nothing! So what do I do now? It accepts Flashes and restores, but it's like the Boot Files are corrupted. And I cannot JTAG, so is there any other options?
Thanks in Advanced,
NetworkLabs
NetworkLabs said:
Okay, I was told to go here since people on AndroidForums.com had no clue on what to do.
Okay, here are my problems -
I received this Android from my mom and it was running Android 2.1. When I first got it, I turned it on without charging it. It booted up, came to the lockscreen, then about a second later turned off and now refuses to boot. I have tried flashing it with generic Android 2.1 and Stock ATT Android 2.1. But it refuses to do nothing but flashes a green light and vibrates. But that all it does. And PC Companion, SEUS, FlashTool have done nothing! So what do I do now? It accepts Flashes and restores, but it's like the Boot Files are corrupted. And I cannot JTAG, so is there any other options?
Thanks in Advanced,
NetworkLabs
Click to expand...
Click to collapse
Plug in the charger while its off its most likely reallt dead!!!!
sent from my x10 using xda premium
stephenhiscock98 said:
Plug in the charger while its off its most likely reallt dead!!!!
sent from my x10 using xda premium
Click to expand...
Click to collapse
No, because I charged it all night and tried to turn it on with no success. So that isn't the problem...
Flash 2.3 firmware then do root,recovery(just in case you don't have it) and a kernel.
Sent from my Desire HD using xda premium
Here is the firmware, thank the logic please.http://forum.xda-developers.com/showthread.php?t=1749426
Sent from my Desire HD using xda premium
My only fear is after restore/flash to 2.3, it will most likely sit there forever. The screen doesn't even light up! So if is to happen, what do I do?
NetworkLabs said:
My only fear is after restore/flash to 2.3, it will most likely sit there forever. The screen doesn't even light up! So if is to happen, what do I do?
Click to expand...
Click to collapse
No it wont if you flash stock 2.3 it will wotk!
sent from my x10 using xda premium
I had quite the similar issue with my x10i. One day it just decided to stop working completely. No lights no nothing, tried everything, just dead. So I contacted SE and they said they could do nothing if the software had been tampered with, no matter how much I assured them if was a hardware related fault.. So I went to my carrier and they sent me to a phone repairing company (Fonemenders here in Ireland), who try fix the phone themselves by getting parts in from the manufacturers. If they deem your phone irreparable they will get you a new replacement. This is exactly what happened me. So the other day I received an email saying that seeing as my x10 couldn't be fixed, I'd be receiving a Sony Arc as a replacement! So i'm happily waiting for the Arc to get here while I use my moms old x8.
So my best advice if nothing is working, go to your carrier and hopefully they can get you through to a phone repairing place, and I wish you as good luck as my own
Well, I cannot replace the Phone since I am not really using it as a Phone. It will not be activated, it's just to mess around with. And I really don't want to buy a Samsung Galaxy Player just so I don't have to deal with this. So I'm going to try the Stock ROM now and see if it works. Do I have to wait for boot up or something?
Try to flash with SE Companion. It will work.
Well, I restored using SEUS because it's the only one that recognized the phone, other than FlashTool. After it restored, it said Unplug the phone and wait for first time. It will take a while. So I am currently doing that. Hope it turns on!
Well, I've restored it and it still sits here. What's next?
I am going to try to flash it using s1tool and see if that helps. Also, can someone please respond with what they think is wrong?
Okay, here's another question - In order to load the firmware you told me, does my Bootloader have to be UNLOCKED? If so, how do I do that without ROOT... Because I cannot do anything with the Phone.
NetworkLabs said:
Okay, here's another question - In order to load the firmware you told me, does my Bootloader have to be UNLOCKED? If so, how do I do that without ROOT... Because I cannot do anything with the Phone.
Click to expand...
Click to collapse
Nooo to flash a stock firmware you don't need unlocked bootloader
sent from my x10 using xda premium
Well, it won't let it. It either doesn't recognize the device or it returns a error... =/
I cannot flash the firmware that you suggested! It get's to system.sin and then aborts with no error information...
Any additional help?
NetworkLabs said:
I cannot flash the firmware that you suggested! It get's to system.sin and then aborts with no error information...
Click to expand...
Click to collapse
I have a question for you... is the phone rooted ? If not then try following
1) start your PC companion and select update software
2) if software say, your phone is up to date then use here will be repair option you need to select it.
3) once you select repair it will download stock GB 2.3.3 and after download it will ask you to plug you phone in flash mode
4) remove phones battery and connect the phone to your laptop.
5) now place the battery back while holding down the back button (3rd button from left) { this step is important as this will get your phone into flash mode.
6) above steps should get your phone back onto stock unrooted ROM...
if you want then use flash tool to root it again but be careful with kernels and bootloader
Set from my Transforer TF101 using xda app-developers app
Well, I think I have tried that and it still won't boot. But I will try again. (PS - Sorry for this old thread, but I just needed a break on working on it! I am going to try again and see if it works!)
UPDATE: Nothing worked, finally went to service center and they changed motherboard , it took 8 days but my ray is back #THANKUWARRANTY
This thread is not a question thread, i am posting here to warn all xperia ray users.
My Story:
Yesterday i installed ICS Pureness rom but i didnt used sirkay kernel with that instead i used .431 stock kernel (I think here is the problem).
After that i used it 20-30 mins and went back to stock .62 GB using flashtool.
I got news that stable CM9 is available, so i installed latest stable Cyanogenmod9 (cm-9.0.0-urushi.zip downloaded from official CM site), used it 5-10 mins
I dont like it either so i returned to GB .62 using cwm backup made before installing CM. Everything worked fine but my phone was not charging , just showing that its charging.
That time battery percentage was 12% it was constantly decreasing although phone was showing its charging. After few mins it turned off and i tried to turn on but phone didnt started , red led blinked 3 times and went off.
I tried another battery and phone works fine but battery still not charging. (it is showing charging but battery percentages are decreasing)
I Also charged my old battery with other phone and tried still no luck phone is unable to charge battery.
I flashed .62 firmware again , still no luck
Left my phone in charging around 5+ hours, still not charging.
Since my phone is unable to charge battery , i am charging it using a direct battery charger, by 15 mins of charging it gives me 10-12% battery. (this is only way to boot my phone and test repairing methods)
UPDATE: Tried method by emosis , Flashed stock .431 using flashtool then flashed sirkay's XRay V7.3.431 kernel but still no luck
These guys are facing same problem too.
1. http://forum.xda-developers.com/showthread.php?t=1808552
2. http://forum.xda-developers.com/showthread.php?t=1831935
Note: I think its software problem but i dont know how to fix it. Basically i am stuck.
So ray users you have been warned , dont try stable CM9.0 over .62 GB firmware otherwise you will lose your phone.
Dont forget to share to aware users, its a very big problem and If you have any suggestion please reply (#seriously so we can make this thread helpful)
If there is really no way To fix it, then maybe get one of these?http://pages.ebay.com/link/?nav=item.view&id=320777472336 I got one and love it. Comes in handy.
Sent from my PARANOID ANDROID
xperia ray said:
Note: I am 1000% sure its software problem but i dont know how to fix it , f**k you sony and Cyanogenmod team.
Click to expand...
Click to collapse
Bravo for the beautiful language. Punks like u dont deserve any help whatsoever.
Bro
Try to do what i say..
Use a charged battery..
Put out battery 1 minute.. Then turn on phone and get fastboot screen and flash sirkay latest kernel 2 times..when flash finished turn off phone and again put out battery 1 minutes turn on phone and get recovery screen - fastboot screen - flash sirkay kernel again.. then turn off phone disconnect phone from computer and connect it to charger after see charging screen turn on ur phone normally and say us the result
Are you talking about this kernel ?? = http://forum.xda-developers.com/showpost.php?p=29739291&postcount=1962
For your information= My phone is currently on GB .62 stock (i charged my phone battery separately without phone >> reinserted battery >> flash .62 stock using flashtool)
EDIT: Tried sirkay kernel not working.
When things go totally out of hand, I usually reinstall the stock ROM with Sony Ericsson Update Service with "software update+factory reset: option. In 99.5% cases it works.
(Well it might not be helpful if it SEUS does not recognize phones with unlocked bootloader.)
Its ok do it with sirkay latest kernel and install pureness you used before bro.. factory reset wipe data and dalvik cache..
Sent from my ST18i using xda app-developers app
tintin100 said:
When things go totally out of hand, I usually reinstall the stock ROM with Sony Ericsson Update Service with "software update+factory reset: option. In 99.5% cases it works.
(Well it might not be helpful if it SEUS does not recognize phones with unlocked bootloader.)
Click to expand...
Click to collapse
Problem is beyond that, i installed stock rom using flashtool but not working.
emosis said:
Its ok do it with sirkay latest kernel and install pureness you used before bro.. factory reset wipe data and dalvik cache..
Sent from my ST18i using xda app-developers app
Click to expand...
Click to collapse
Thanks a lot for your reply, i am downloading pureness again , actually deleted it.
If you can also explain why you are saying to use pureness rom ?? any technical reason behind it ??
No i said that cuz i thought u have it.. but do this :ut out battery 1 minute then recovery menu and fastboot mode use fastboot mode for flashin the kernel 2 times and put out battery again 1 minute then turn on recovery screen factory reset and wipe dalvik cache and install the rom and restart phone and say result i did this to solve mine and it worked ( dont reset battery stats)
Sent from my ST18i using xda app-developers app
@emosis bro , i am booting to fastboot like we normally do (switch off phone>>hold volume up and connect to pc)
is there any different method too, as you are saying - "recovery menu and fastboot mode"
I also tried , booted in recovery then selected reboot in fastboot mode but phone started normally.
Thanks a lot.
Note: I am not a noob, in fact a developer kinda geek, but this problem made me sick and tired , i surrendered. seems like hardware problem.
If possible please tell me what happened with your phone, did you faced exact problem like i did ?
In sirkay kernel reboot in fastbootmode or while using phone settings application develop usb debugging on..and use flashtool reboot in fastboot mode phone led must be blue.. if it s ok flash the kernel 2 times and do what i said bro.
Sent from my ST18i using xda app-developers app
flash .72 baseband and reflash xkernel v7.3.431 again
sirkay said:
flash .72 baseband and reflash xkernel v7.3.431 again
Click to expand...
Click to collapse
i flashed .431 so it have .72 baseband already. Should i flash xkernel v7.3.431 once more ?
yes, then go into recovery
- wipe data / factory reset
- wipe dalvik-cache
- wipe battery stats
- flash rom
- boot into rom
Strange, I had no problems when going back to .62 from CM9 stable...
I've heard that you can wipe EVERYTHING from the phone memory, leaving only basic programs and protocols like flashmode and fastboot by taking the battery out and charging the phone without for some time. Maybe it should help, though I never used this method and I don't know if it's safe or will it ever work...
I had battery %0 problem before can't charge phone.. i had it cuz battery stats was so low i flashed a kernel and used clear battery stats and installed a new rom.. ...... tried many thing to solve so i solved this problem the way i explained..hope you can solve it too..
Sent from my ST18i using xda app-developers app
emosis said:
I had battery %0 problem before can't charge phone.. i had it cuz battery stats was so low i flashed a kernel and used clear battery stats and installed a new rom.. ...... tried many thing to solve so i solved this problem the way i explained..hope you can solve it too..
Sent from my ST18i using xda app-developers app
Click to expand...
Click to collapse
my phone is not showing 0% all the time, it shows 10-11% battery and when i connect it, instead of charging it start to discharge.
Since my phone is unable to charge battery , i am charging it using a direct battery charger, by 15 mins of charging it gives me 10-12% battery. (this is only way to boot my phone and test repairing methods)
So could you try the way i said?
Sent from my ST18i using xda app-developers app
sirkay said:
yes, then go into recovery
- wipe data / factory reset
- wipe dalvik-cache
- wipe battery stats
- flash rom
- boot into rom
Click to expand...
Click to collapse
tried but not working, i think its hardware problem in phone. (Except charging battery everything is working fine)
Battery is working (i charge it using external charger)