So Samsung released an update for this phone last night, and I very stupidly hit install and I was rooted.
Now the only thing it boots to is clockwork recovery.
I downloaded the latest stock rom but odin won't flash it.
Think I got to flash the stock recovery to flash the rom, how do I do this?
Also, how do I root this again after updating?
You don't need the stock recovery to flash the ROM. Odin should flash it. What problem is it giving you when you try to flash? Do you have the right odin package?
GazaIan said:
You don't need the stock recovery to flash the ROM. Odin should flash it. What problem is it giving you when you try to flash? Do you have the right odin package?
Click to expand...
Click to collapse
Odin package? Don you mean the taar.md5? It's S7500XXLH3_S7500BTULH1_S7500XXLH1_HOME.tar.md5
I'm trying to flash it with Odin 1.85 with it loaded as a PDA
Yep, the tar.md5. What happens when you try to flash it? do one of the boxes at the top say "FAIL" or does it just freeze?
GazaIan said:
Yep, the tar.md5. What happens when you try to flash it? do one of the boxes at the top say "FAIL" or does it just freeze?
Click to expand...
Click to collapse
Just freezes left it for 15 minutes.
Log below
Code:
<ID:0/005> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> S7500XXLH3_S7500BTULH1_S7500XXLH1_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Odin v.3 engine (ID:5)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
droobey said:
Just freezes left it for 15 minutes.
Log below
Code:
<ID:0/005> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> S7500XXLH3_S7500BTULH1_S7500XXLH1_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Odin v.3 engine (ID:5)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
Click to expand...
Click to collapse
Update: OK turns out recovery and download are two completely different things.
Recovery Mode: volume up+ volume down + home + power (what it was booting to by itself)
Download Mode: volume down + home + power
Everything is working now!
Related
I've searched everywhere, I am not a noob when it comes to root/flashing/odin, but I am at a dead end here.
I picked up my phone today to see it at the Samsung i-9300 boot screen, just sitting there. I popped the battery and tried to reboot, no go. Tried to boot to recovery, won't go past that Samsung screen. I can boot to download mode, and odin recognizes the phone, but when I try to flash anything to the phone, odin freezes at SetupConnection.
Does anyone have any ideas?
Output from odin
<ID:0/004> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> KIES_HOME_I9300XXDLJ4_I9300OXADLJ4_368423_REV00_user_low_ship.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Odin v.3 engine (ID:4)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
This is a stock firmware downloaded from SamMobile. I have tried just a twrp recovery to try to boot to recovery and that does not work either. I found a few .pit files and tried to re partition with those, hoping that would help, but no luck. Running windows 8, also tried windows 7 with no luck. Has anyone ever run into this?
Hi all. I was following the video to do the NC5 update. I loaded the zip on my ext sd, and the super su update. On my PC i have odin 3.09 and the tar files from the forum post. Everything was going fine until i got to ODIN.
I rebooted to download mode from safe strap as per directions. Connected USB, drivers found the phone and odin showed it connected. I choose the AP file and the CP file in the proper places, and choose start. The bar started on the phone, but has not moved past the first nub, and the odin window didnt update the box like it normally does with progress bars and activity... however the messages window at the bottom did update with this:
Code:
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> AP_VZW_I545VRUFNC5_I545VZWFNC5_1151670_REV06_user_low_ship_MULTI_CERT.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> CP_VZW_I545VRUFNC5_I545VZWFNC5_1151670_REV06_user_low_ship_MULTI_CERT.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> SingleDownload.
<ID:0/003> boot.img
So, it seems to be stalled here and im not sure what to do now. Its been like this for 15 minutes or so at least.
I have attached a screenshot of the odin window. Still no activity....
So what should i do now? Thanks for the help!
EDIT------------------------
To resolve this, i unplugged the USB, closed ODIN, pulled the battery let it sit for a while, hooked my usb into the computer (back USB port). Put battery in and booted to download mode by buttons (Vol DWN + HOME + Power). Re ran odin after the drivers settled up and ran the flash again and it proceeded properly. all appears to boot now.
Sorry, currently a new member but being the noob I am- it seems I flashed my International I9300 to a different device (SGH-I747)...
My device is stuck on the Samsung start-up (no biggie), and I believe it's soft-bricked but currently I have no idea what to do.
I've been on Odin and followed many guides to get it back to stock but to no avail. It all fails. I believe something with the MTP failing to install is also a problem. I've done the CMD command and went into regedit and a number of other things.
Right now Kies can't even do an Emergency Firmware Recovery won't pick it up.
Also when I get it in Recovery Mode it exits out and turns to a black screen after a couple of seconds.
I follow this : http://forum.xda-developers.com/galaxy-s3/help/solved-pit-bricked-dead-problem-gt-t2535367
As the PIT seems to PASS but from there all the other PDA's I try to start fail.
---
I can get it into Odin Mode.
And currently has
Product Name : SGH-I747
Custom Binary Download: Yes (7 counts)
Current Binary : Custom
System Status : Official
QualComm SecureBoot: Enable
---
Help would be much appreciated.
How did this occur? Well actually, I just did a Factory Reset when it worked and then it got stuck loading for hours... Then tried to flash something in... Apparently got the wrong one. And here I am.
simonheros said:
Sorry, currently a new member but being the noob I am- it seems I flashed my International I9300 to a different device (SGH-I747)...
My device is stuck on the Samsung start-up (no biggie), and I believe it's soft-bricked but currently I have no idea what to do.
I've been on Odin and followed many guides to get it back to stock but to no avail. It all fails. I believe something with the MTP failing to install is also a problem. I've done the CMD command and went into regedit and a number of other things.
Right now Kies can't even do an Emergency Firmware Recovery won't pick it up.
Also when I get it in Recovery Mode it exits out and turns to a black screen after a couple of seconds.
I follow this : http://forum.xda-developers.com/galaxy-s3/help/solved-pit-bricked-dead-problem-gt-t2535367
As the PIT seems to PASS but from there all the other PDA's I try to start fail.
---
I can get it into Odin Mode.
And currently has
Product Name : SGH-I747
Custom Binary Download: Yes (7 counts)
Current Binary : Custom
System Status : Official
QualComm SecureBoot: Enable
---
Help would be much appreciated.
How did this occur? Well actually, I just did a Factory Reset when it worked and then it got stuck loading for hours... Then tried to flash something in... Apparently got the wrong one. And here I am.
Click to expand...
Click to collapse
it seems I flashed my International I9300 to a different device (SGH-I747)??? what does this mean? flashed SGH-I747 firmware in I9300? just want to make sure that what i understood is right because your post is making some confusion..
Can you tell me if your device is 16GB or 32GB or 64GB? pit file for all three of them is different. if you will use correct one than this should not fail.. i dont think that mtp has to do anything with odin but if it does than uninstall all the drivers that are currently install(your device drivers) and download and install samsung drivers from here: http://www.mediafire.com/?7iy79emc0bf1fb4 and then try to connect the device again.. I hope this helps you..
suyash1629 said:
it seems I flashed my International I9300 to a different device (SGH-I747)??? what does this mean? flashed SGH-I747 firmware in I9300? just want to make sure that what i understood is right because your post is making some confusion..
Can you tell me if your device is 16GB or 32GB or 64GB? pit file for all three of them is different. if you will use correct one than this should not fail.. i dont think that mtp has to do anything with odin but if it does than uninstall all the drivers that are currently install(your device drivers) and download and install samsung drivers from here: ----------- and then try to connect the device again.. I hope this helps you..
Click to expand...
Click to collapse
Thank you for the response.
Yes I flashed I747 firmware in I9300. I apologize for the poor wording. My device is 16 GB. The one from the thread I linked is said to be used by 16 GB variant, so I believe it works. (Passes)
I don't get that MTP driver error anymore, but now when I try to put a Bootloader in it says that it's an unsupported dev type.
A person got a similar problem here : s3forums.com/forum/galaxy-s3-help/5772-stuck-download-mode-diffrent-device-type-9300-sgh-i747 ( can't post link) but it appears to be bricked flat out...
simonheros said:
Sorry, currently a new member but being the noob I am- it seems I flashed my International I9300 to a different device (SGH-I747)...
My device is stuck on the Samsung start-up (no biggie), and I believe it's soft-bricked but currently I have no idea what to do.
I've been on Odin and followed many guides to get it back to stock but to no avail. It all fails. I believe something with the MTP failing to install is also a problem. I've done the CMD command and went into regedit and a number of other things.
Right now Kies can't even do an Emergency Firmware Recovery won't pick it up.
Also when I get it in Recovery Mode it exits out and turns to a black screen after a couple of seconds.
I follow this : http://forum.xda-developers.com/galaxy-s3/help/solved-pit-bricked-dead-problem-gt-t2535367
As the PIT seems to PASS but from there all the other PDA's I try to start fail.
---
I can get it into Odin Mode.
And currently has
Product Name : SGH-I747
Custom Binary Download: Yes (7 counts)
Current Binary : Custom
System Status : Official
QualComm SecureBoot: Enable
---
Help would be much appreciated.
How did this occur? Well actually, I just did a Factory Reset when it worked and then it got stuck loading for hours... Then tried to flash something in... Apparently got the wrong one. And here I am.
Click to expand...
Click to collapse
I think mate you should check if your bootloader in locked or unlocked. As you mention above about QualComm Secure boot :Enable. may be before you was using gt-i9300 firmware it must be unlocked but after you flashed wrong firmware may be your bootloader got locked.
try to download complete stock 4.3 firmware from sammobile.com for correct variant i.e GT-I9300.
Download it and extract it and you will get .tar files
download latest Odin ( google it ) and open it.
put your phone in download mode by pressing volume down + home key + power key for few deconds until download mode screen appear.
press volume up key to goto download mode. connect your phone to your computer and wait till it install all the necessary driver. if you drivers are not installed properly then you have to manually installe the driver for your phone. download galaxy toolkit for s3 from xda and install it. search for the folder name galaxy toolkit in your computer. basically it will be in c:/ drive. open that folder and you will find driver folder under it. Inside the driver folder there will .exe file of driver. but before installing disconnect your phone computer and then install the driver. after the installation of your driver plug in again and wait till it install all the drivers.
Inside odin you must have to see that there is COM ID in 1st box and below it is written attached. if you dont see that then your driver are not installed correctly. uninstall and install it again.
after the driver install click on AP and select the AP .tar file that we extracted after downloading. select the appropriate file associated with it.
click on start and wait few minutes till the process gets complete.
If all things goes right you may get your phone back again.
Mustakim_456 said:
I think mate you should check if your bootloader in locked or unlocked. As you mention above about QualComm Secure boot :Enable. may be before you was using gt-i9300 firmware it must be unlocked but after you flashed wrong firmware may be your bootloader got locked.
try to download complete stock 4.3 firmware from sammobile.com for correct variant i.e GT-I9300.
Download it and extract it and you will get .tar files
download latest Odin ( google it ) and open it.
put your phone in download mode by pressing volume down + home key + power key for few deconds until download mode screen appear.
press volume up key to goto download mode. connect your phone to your computer and wait till it install all the necessary driver. if you drivers are not installed properly then you have to manually installe the driver for your phone. download galaxy toolkit for s3 from xda and install it. search for the folder name galaxy toolkit in your computer. basically it will be in c:/ drive. open that folder and you will find driver folder under it. Inside the driver folder there will .exe file of driver. but before installing disconnect your phone computer and then install the driver. after the installation of your driver plug in again and wait till it install all the drivers.
Inside odin you must have to see that there is COM ID in 1st box and below it is written attached. if you dont see that then your driver are not installed correctly. uninstall and install it again.
after the driver install click on AP and select the AP .tar file that we extracted after downloading. select the appropriate file associated with it.
click on start and wait few minutes till the process gets complete.
If all things goes right you may get your phone back again.
Click to expand...
Click to collapse
Thank you for the response.
Drivers work and it's been able to connect to ODIN but it fails regardless of the stock firmware I flash via PDA.
I get this :
<ID:0/006> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9300XXBLH1_I9300OLBBLH1_I9300DXLH1_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/006> Odin v.3 engine (ID:6)..
<ID:0/006> File analysis..
<ID:0/006> SetupConnection..
<ID:0/006> Initialzation..
<ID:0/006> Get PIT for mapping..
<ID:0/006> Firmware update start..
<ID:0/006> system.img
<ID:0/006> NAND Write Start!!
<ID:0/006> FAIL!
<OSM> All threads completed. (succeed 0 / failed 1)
For Bootloader
<ID:0/006> Removed!!
<ID:0/006> Added!!
<ID:0/006> Odin v.3 engine (ID:6)..
<ID:0/006> File analysis..
<ID:0/006> SetupConnection..
<ID:0/006> Initialzation..
<ID:0/006> Get PIT for mapping..
<ID:0/006> Firmware update start..
<ID:0/006> sboot.bin
<ID:0/006> NAND Write Start!!
<ID:0/006> FAIL!
<OSM> All threads completed. (succeed 0 / failed 1)
----
It would help to mention that I have a second i9300 that works and hasn't been touched or anything. Can I do something with that?
edit* It says unsupported dev type on my screen when it fails..
simonheros said:
Thank you for the response.
Drivers work and it's been able to connect to ODIN but it fails regardless of the stock firmware I flash via PDA.
I get this :
<ID:0/006> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9300XXBLH1_I9300OLBBLH1_I9300DXLH1_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/006> Odin v.3 engine (ID:6)..
<ID:0/006> File analysis..
<ID:0/006> SetupConnection..
<ID:0/006> Initialzation..
<ID:0/006> Get PIT for mapping..
<ID:0/006> Firmware update start..
<ID:0/006> system.img
<ID:0/006> NAND Write Start!!
<ID:0/006> FAIL!
<OSM> All threads completed. (succeed 0 / failed 1)
For Bootloader
<ID:0/006> Removed!!
<ID:0/006> Added!!
<ID:0/006> Odin v.3 engine (ID:6)..
<ID:0/006> File analysis..
<ID:0/006> SetupConnection..
<ID:0/006> Initialzation..
<ID:0/006> Get PIT for mapping..
<ID:0/006> Firmware update start..
<ID:0/006> sboot.bin
<ID:0/006> NAND Write Start!!
<ID:0/006> FAIL!
<OSM> All threads completed. (succeed 0 / failed 1)
----
It would help to mention that I have a second i9300 that works and hasn't been touched or anything. Can I do something with that?
edit* It says unsupported dev type on my screen when it fails..
Click to expand...
Click to collapse
Looks like your Nand maybe corrupt try flashing the rescue firmware >> http://forum.xda-developers.com/showpost.php?p=30087735 <<
tallman43 said:
Looks like your Nand maybe corrupt try flashing the rescue firmware >> http://forum.xda-developers.com/showpost.php?p=30087735 <<
Click to expand...
Click to collapse
<ID:0/006> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> BOOTLOADER_I9300XXEMG4_1314436_REV00_user_low_ship.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> CODE_I9300XXEMG4_1314436_REV00_user_low_ship.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> MODEM_I9300XXEMG4_1314436_REV00_user_low_ship.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> CSC_I9300OXAEMG4_KOR_FACTORY_user_low_ship.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/006> Odin v.3 engine (ID:6)..
<ID:0/006> File analysis..
<ID:0/006> SetupConnection..
<ID:0/006> Initialzation..
<ID:0/006> Set PIT file..
<ID:0/006> DO NOT TURN OFF TARGET!!
<ID:0/006> Get PIT for mapping..
<ID:0/006> Firmware update start..
<ID:0/006> sboot.bin
<ID:0/006> NAND Write Start!!
<ID:0/006> FAIL!
<OSM> All threads completed. (succeed 0 / failed 1)
SECURE CHECK FAIL : PIT
Unsupport: dev_type
---
None of the PIT's work now... And pretty much none of the files passed... D:
simonheros said:
<ID:0/006> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> BOOTLOADER_I9300XXEMG4_1314436_REV00_user_low_ship.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> CODE_I9300XXEMG4_1314436_REV00_user_low_ship.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> MODEM_I9300XXEMG4_1314436_REV00_user_low_ship.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> CSC_I9300OXAEMG4_KOR_FACTORY_user_low_ship.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/006> Odin v.3 engine (ID:6)..
<ID:0/006> File analysis..
<ID:0/006> SetupConnection..
<ID:0/006> Initialzation..
<ID:0/006> Set PIT file..
<ID:0/006> DO NOT TURN OFF TARGET!!
<ID:0/006> Get PIT for mapping..
<ID:0/006> Firmware update start..
<ID:0/006> sboot.bin
<ID:0/006> NAND Write Start!!
<ID:0/006> FAIL!
<OSM> All threads completed. (succeed 0 / failed 1)
SECURE CHECK FAIL : PIT
Unsupport: dev_type
---
None of the PIT's work now... And pretty much none of the files passed... D:
Click to expand...
Click to collapse
Any progress??
suyash1629 said:
Any progress??
Click to expand...
Click to collapse
None what so-ever. I hit a dead end and had to get a replacement.
I'm just not going to mess with the new one anymore...
Hey guys, I have this Verizon Fascinate that I used to use when I was wayyy younger. Back then I was using it, deleted a wrong folder when I was browsing through the My Files app, and it hasn't turned on since. If I try to power it on, all I get is a white screen that continues to flash. I've looked at all of the other threads about resetting the Fascinate to stock with Odin and Heimdall, and I've tried the steps given there, but it hasn't helped. I can still set it to download mode, and I can still charge it with the charging battery screen, but no recovery/boot up what so ever. I tried flashing multiple stock firmwares in Odin with the stock pit file or the atlas pit file, but this is all I get:
<ID:0/004> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> CI500_VZW_EH03_GB_CM.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Odin v.3 engine (ID:4)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<OSM> All threads completed. (succeed 0 / failed 1)
The phone wasn't rooted before and didn't have any sort of custom rom on it. Any help would be greatly appreciated by those still browsing these forums.
MexicanBRUHH said:
Hey guys, I have this Verizon Fascinate that I used to use when I was wayyy younger. Back then I was using it, deleted a wrong folder when I was browsing through the My Files app, and it hasn't turned on since. If I try to power it on, all I get is a white screen that continues to flash. I've looked at all of the other threads about resetting the Fascinate to stock with Odin and Heimdall, and I've tried the steps given there, but it hasn't helped. I can still set it to download mode, and I can still charge it with the charging battery screen, but no recovery/boot up what so ever. I tried flashing multiple stock firmwares in Odin with the stock pit file or the atlas pit file, but this is all I get:
<ID:0/004> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> CI500_VZW_EH03_GB_CM.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Odin v.3 engine (ID:4)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<OSM> All threads completed. (succeed 0 / failed 1)
The phone wasn't rooted before and didn't have any sort of custom rom on it. Any help would be greatly appreciated by those still browsing these forums.
Click to expand...
Click to collapse
To do it, get this file.
https://gofile.io/?c=tJd0Pd
Then get odin v1.85
https://gofile.io/?c=WHkZHO
Launch odin with admin powers (sudo/su for linux, or whatever).
Then click PDA and select the tar.md5 file and start.
Anyone getting this error when trying to update to BRE2? Odin will flash ARA2 without a problem.
Never Mind. Didn't realize there's a newer version of odin, 3.13.1
jd1639 said:
Anyone getting this error when trying to update to BRE2? Odin will flash ARA2 without a problem.
Never Mind. Didn't realize there's a newer version of odin, 3.13.1
Click to expand...
Click to collapse
You just updated the ODIN? Then it's ok now? I have similar problems with yours.. unsupported dev
Biosystematics said:
You just updated the ODIN? Then it's ok now? I have similar problems with yours.. unsupported dev
Click to expand...
Click to collapse
Yes. The compression format for the firmware changed on Oreo and it needs an update Odin to run.
Sent from my [device_name] using XDA-Developers Legacy app
jd1639 said:
Anyone getting this error when trying to update to BRE2? Odin will flash ARA2 without a problem.
Never Mind. Didn't realize there's a newer version of odin, 3.13.1
Click to expand...
Click to collapse
Hello every one
I have Samsung galaxy C7 Pro (SM-C7010), I wished to install custom recovery TWRP and root my mobile.
After flashing custom recovery TWRP using odin 3.12.7 and samsung USB driver, my Mobile starts rebooting again and again,
I tired all suggestion given by XDA experts and you tubers, flash newer version of TWRP for samsung C7, wipe cache/delvik, factory rest, mout system etc.,
After all above mess, I decided to flash samsung offial firmware stock recovery ( using 4 file, BL, AP, CP,CSC) but during flashing I have this error "Unsupport dev_type"
This is the code, please help where the problem is?
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Added!!
<ID:0/003> Removed!!
<ID:0/003> Added!!
<ID:0/003> Odin engine v(ID:3.1207)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Set PIT file..
<ID:0/003> DO NOT TURN OFF TARGET!!
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> NAND Write Start!!
<ID:0/003> SingleDownload.
<ID:0/003> aboot.mbn.lz4
<ID:0/003> FAIL!
<ID:0/003>
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
You need 3.13.1 version of odin. You're using an older version.
jd1639 said:
Anyone getting this error when trying to update to BRE2? Odin will flash ARA2 without a problem.
Never Mind. Didn't realize there's a newer version of odin, 3.13.1
Click to expand...
Click to collapse
Yeah, just update Odin. It works for me.
Thank bro.