Hi all. I was following the video to do the NC5 update. I loaded the zip on my ext sd, and the super su update. On my PC i have odin 3.09 and the tar files from the forum post. Everything was going fine until i got to ODIN.
I rebooted to download mode from safe strap as per directions. Connected USB, drivers found the phone and odin showed it connected. I choose the AP file and the CP file in the proper places, and choose start. The bar started on the phone, but has not moved past the first nub, and the odin window didnt update the box like it normally does with progress bars and activity... however the messages window at the bottom did update with this:
Code:
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> AP_VZW_I545VRUFNC5_I545VZWFNC5_1151670_REV06_user_low_ship_MULTI_CERT.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> CP_VZW_I545VRUFNC5_I545VZWFNC5_1151670_REV06_user_low_ship_MULTI_CERT.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> SingleDownload.
<ID:0/003> boot.img
So, it seems to be stalled here and im not sure what to do now. Its been like this for 15 minutes or so at least.
I have attached a screenshot of the odin window. Still no activity....
So what should i do now? Thanks for the help!
EDIT------------------------
To resolve this, i unplugged the USB, closed ODIN, pulled the battery let it sit for a while, hooked my usb into the computer (back USB port). Put battery in and booted to download mode by buttons (Vol DWN + HOME + Power). Re ran odin after the drivers settled up and ran the flash again and it proceeded properly. all appears to boot now.
Related
So Samsung released an update for this phone last night, and I very stupidly hit install and I was rooted.
Now the only thing it boots to is clockwork recovery.
I downloaded the latest stock rom but odin won't flash it.
Think I got to flash the stock recovery to flash the rom, how do I do this?
Also, how do I root this again after updating?
You don't need the stock recovery to flash the ROM. Odin should flash it. What problem is it giving you when you try to flash? Do you have the right odin package?
GazaIan said:
You don't need the stock recovery to flash the ROM. Odin should flash it. What problem is it giving you when you try to flash? Do you have the right odin package?
Click to expand...
Click to collapse
Odin package? Don you mean the taar.md5? It's S7500XXLH3_S7500BTULH1_S7500XXLH1_HOME.tar.md5
I'm trying to flash it with Odin 1.85 with it loaded as a PDA
Yep, the tar.md5. What happens when you try to flash it? do one of the boxes at the top say "FAIL" or does it just freeze?
GazaIan said:
Yep, the tar.md5. What happens when you try to flash it? do one of the boxes at the top say "FAIL" or does it just freeze?
Click to expand...
Click to collapse
Just freezes left it for 15 minutes.
Log below
Code:
<ID:0/005> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> S7500XXLH3_S7500BTULH1_S7500XXLH1_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Odin v.3 engine (ID:5)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
droobey said:
Just freezes left it for 15 minutes.
Log below
Code:
<ID:0/005> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> S7500XXLH3_S7500BTULH1_S7500XXLH1_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Odin v.3 engine (ID:5)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
Click to expand...
Click to collapse
Update: OK turns out recovery and download are two completely different things.
Recovery Mode: volume up+ volume down + home + power (what it was booting to by itself)
Download Mode: volume down + home + power
Everything is working now!
as per title, i'm trying to flash with repartitioning using a pit file but odin gets stuck at the do not turn off target message.
printout:
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9100_APBOOT_I9100XXLPH_CL118559_REV02_user_low_ship.tar.md5 is valid.
<OSM> I9100_CODE_I9100XXLPH_CL118559_REV02_user_low_ship.tar.md5 is valid.
<OSM> MODEM_I9100XXLPH_REV_02_CL1104396.tar.md5 is valid.
<OSM> GT-I9100-MULTI-CSC-OXALPH.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Set PIT file..
<ID:0/003> DO NOT TURN OFF TARGET!!
there is no progress bar on both odin and my phone as well. any ideas?
Pull the plug and see if the phone will boot. If odin never started writing to the phone you will be back where you started. Then just flash straight to next rom. Odin sometimes acts up and a reboot of computer, different port, change of cable, or just trying again seems to normally fix the issue though.
Hello, i'm a XDA noob and i have a Problem with my i9100.
I figuered out that i have a Soft Brick and thanks to the Guide i fixed that one.
The battery was full when i went sleeping. And half an hour ago everything seems to be fine. 95% battery, phone is working. I had flight mode activated and just deactivated it. I got an Error that the SMS app was closed, but everything was still fine. I locked the Screen, 5 minutes later i came back and it Soft Bricked again. (The first Soft Brick came from out of nowhere, too).
i Had the Original Samsung Stock 4.0.3 (the download from in the Guide) installed. It worked fine after Step 4.
Symptoms:
Does not boot
No Recovery
Download mode works if connected with USB
Loading works partially, the symbol apears, but after 9 seconds it disapears and after 6 seconds it apears again...
If i try to enter Download mode with low battery and no USB conection, i get a Screen warning that Battery is low
I Randomly get a Screen flicker which lasts about 0.1 - 0.5 seconds. The 0.5 ones show the Andorid logo who is installing something . I Think the 0.1 second ones show the same thing but i'm not sure.
Odin Flash works ! Here's the log
Code:
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9100_APBOOT_I9100XXLPH_CL118559_REV02_user_low_ship.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9100_CODE_I9100XXLPH_CL118559_REV02_user_low_ship.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> MODEM_I9100XXLPH_REV_02_CL1104396.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> GT-I9100-MULTI-CSC-OXALPH.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Added!!
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> boot.bin
<ID:0/003> NAND Write Start!!
<ID:0/003> Sbl.bin
<ID:0/003> param.lfs
<ID:0/003> boot.bin
<ID:0/003> Sbl.bin
<ID:0/003> param.lfs
<ID:0/003> zImage
<ID:0/003> factoryfs.img
<ID:0/003> data.img
<ID:0/003> cache.img
<ID:0/003> hidden.img
<ID:0/003> modem.bin
<ID:0/003> Transmission Complete..
<ID:0/003> Now Writing.. Please wait about 2 minutes
<ID:0/003> Receive Response from boot-loader
<ID:0/003> cache.img
<ID:0/003> RQT_CLOSE !!
<ID:0/003> RES OK !!
<ID:0/003> Removed!!
<ID:0/003> Remain Port .... 0
<OSM> All threads completed. (succeed 1 / failed 0)
After Odin it wont boot directly nor Recovery works, but if i wait a few minutes and change battery ( i have 2 batterys ) multiple times, it somehow starts to show the same old "andoird is working" screen and then boots in a nice stock Android 4.0.3.
Additional Information
I had installed CM 10.1 (with CWM) before. And it worked fine for months.
Someday the battery usage became extrem (there is a Problem with the SD card, because it's always saying the SD was removed and installed, checking for errors, and that costs a lot of battery power...
I deleted all the data/data manually and some system folders --> Boot Loop , so i decided to swich back to Stock Android 4.2.2. That worked fine, Memory usage is high too if using with a SD card. But OS was stable, till yesterday...
I neither connected my phone with Google yesterday, nor did i sign up with Samsung services, nor did i changed anything, nor did i installed apps.
Now my Question is:
What should i do to get a stable system? Is there any option to get my phone back to factory status? (no i don't mean factory reset, because this only change a few folders but not all on the phone...)
Thank you.
Search for a nuke script in order to get rid of previous ROMs leftovers.
Sent from the little guy
That seemed to work.
I installed CWM and CM 10.1, then i ran the script and after that reinstalled the newest version of CM10.1.
mac.2013 said:
That seemed to work.
I installed CWM and CM 10.1, then i ran the script and after that reinstalled the newest version of CM10.1.
Click to expand...
Click to collapse
Please add [SOLVED] to the title of ur post then.
"To err is human, to forgive is divine"
Sent from my SGS II
Sorry, currently a new member but being the noob I am- it seems I flashed my International I9300 to a different device (SGH-I747)...
My device is stuck on the Samsung start-up (no biggie), and I believe it's soft-bricked but currently I have no idea what to do.
I've been on Odin and followed many guides to get it back to stock but to no avail. It all fails. I believe something with the MTP failing to install is also a problem. I've done the CMD command and went into regedit and a number of other things.
Right now Kies can't even do an Emergency Firmware Recovery won't pick it up.
Also when I get it in Recovery Mode it exits out and turns to a black screen after a couple of seconds.
I follow this : http://forum.xda-developers.com/galaxy-s3/help/solved-pit-bricked-dead-problem-gt-t2535367
As the PIT seems to PASS but from there all the other PDA's I try to start fail.
---
I can get it into Odin Mode.
And currently has
Product Name : SGH-I747
Custom Binary Download: Yes (7 counts)
Current Binary : Custom
System Status : Official
QualComm SecureBoot: Enable
---
Help would be much appreciated.
How did this occur? Well actually, I just did a Factory Reset when it worked and then it got stuck loading for hours... Then tried to flash something in... Apparently got the wrong one. And here I am.
simonheros said:
Sorry, currently a new member but being the noob I am- it seems I flashed my International I9300 to a different device (SGH-I747)...
My device is stuck on the Samsung start-up (no biggie), and I believe it's soft-bricked but currently I have no idea what to do.
I've been on Odin and followed many guides to get it back to stock but to no avail. It all fails. I believe something with the MTP failing to install is also a problem. I've done the CMD command and went into regedit and a number of other things.
Right now Kies can't even do an Emergency Firmware Recovery won't pick it up.
Also when I get it in Recovery Mode it exits out and turns to a black screen after a couple of seconds.
I follow this : http://forum.xda-developers.com/galaxy-s3/help/solved-pit-bricked-dead-problem-gt-t2535367
As the PIT seems to PASS but from there all the other PDA's I try to start fail.
---
I can get it into Odin Mode.
And currently has
Product Name : SGH-I747
Custom Binary Download: Yes (7 counts)
Current Binary : Custom
System Status : Official
QualComm SecureBoot: Enable
---
Help would be much appreciated.
How did this occur? Well actually, I just did a Factory Reset when it worked and then it got stuck loading for hours... Then tried to flash something in... Apparently got the wrong one. And here I am.
Click to expand...
Click to collapse
it seems I flashed my International I9300 to a different device (SGH-I747)??? what does this mean? flashed SGH-I747 firmware in I9300? just want to make sure that what i understood is right because your post is making some confusion..
Can you tell me if your device is 16GB or 32GB or 64GB? pit file for all three of them is different. if you will use correct one than this should not fail.. i dont think that mtp has to do anything with odin but if it does than uninstall all the drivers that are currently install(your device drivers) and download and install samsung drivers from here: http://www.mediafire.com/?7iy79emc0bf1fb4 and then try to connect the device again.. I hope this helps you..
suyash1629 said:
it seems I flashed my International I9300 to a different device (SGH-I747)??? what does this mean? flashed SGH-I747 firmware in I9300? just want to make sure that what i understood is right because your post is making some confusion..
Can you tell me if your device is 16GB or 32GB or 64GB? pit file for all three of them is different. if you will use correct one than this should not fail.. i dont think that mtp has to do anything with odin but if it does than uninstall all the drivers that are currently install(your device drivers) and download and install samsung drivers from here: ----------- and then try to connect the device again.. I hope this helps you..
Click to expand...
Click to collapse
Thank you for the response.
Yes I flashed I747 firmware in I9300. I apologize for the poor wording. My device is 16 GB. The one from the thread I linked is said to be used by 16 GB variant, so I believe it works. (Passes)
I don't get that MTP driver error anymore, but now when I try to put a Bootloader in it says that it's an unsupported dev type.
A person got a similar problem here : s3forums.com/forum/galaxy-s3-help/5772-stuck-download-mode-diffrent-device-type-9300-sgh-i747 ( can't post link) but it appears to be bricked flat out...
simonheros said:
Sorry, currently a new member but being the noob I am- it seems I flashed my International I9300 to a different device (SGH-I747)...
My device is stuck on the Samsung start-up (no biggie), and I believe it's soft-bricked but currently I have no idea what to do.
I've been on Odin and followed many guides to get it back to stock but to no avail. It all fails. I believe something with the MTP failing to install is also a problem. I've done the CMD command and went into regedit and a number of other things.
Right now Kies can't even do an Emergency Firmware Recovery won't pick it up.
Also when I get it in Recovery Mode it exits out and turns to a black screen after a couple of seconds.
I follow this : http://forum.xda-developers.com/galaxy-s3/help/solved-pit-bricked-dead-problem-gt-t2535367
As the PIT seems to PASS but from there all the other PDA's I try to start fail.
---
I can get it into Odin Mode.
And currently has
Product Name : SGH-I747
Custom Binary Download: Yes (7 counts)
Current Binary : Custom
System Status : Official
QualComm SecureBoot: Enable
---
Help would be much appreciated.
How did this occur? Well actually, I just did a Factory Reset when it worked and then it got stuck loading for hours... Then tried to flash something in... Apparently got the wrong one. And here I am.
Click to expand...
Click to collapse
I think mate you should check if your bootloader in locked or unlocked. As you mention above about QualComm Secure boot :Enable. may be before you was using gt-i9300 firmware it must be unlocked but after you flashed wrong firmware may be your bootloader got locked.
try to download complete stock 4.3 firmware from sammobile.com for correct variant i.e GT-I9300.
Download it and extract it and you will get .tar files
download latest Odin ( google it ) and open it.
put your phone in download mode by pressing volume down + home key + power key for few deconds until download mode screen appear.
press volume up key to goto download mode. connect your phone to your computer and wait till it install all the necessary driver. if you drivers are not installed properly then you have to manually installe the driver for your phone. download galaxy toolkit for s3 from xda and install it. search for the folder name galaxy toolkit in your computer. basically it will be in c:/ drive. open that folder and you will find driver folder under it. Inside the driver folder there will .exe file of driver. but before installing disconnect your phone computer and then install the driver. after the installation of your driver plug in again and wait till it install all the drivers.
Inside odin you must have to see that there is COM ID in 1st box and below it is written attached. if you dont see that then your driver are not installed correctly. uninstall and install it again.
after the driver install click on AP and select the AP .tar file that we extracted after downloading. select the appropriate file associated with it.
click on start and wait few minutes till the process gets complete.
If all things goes right you may get your phone back again.
Mustakim_456 said:
I think mate you should check if your bootloader in locked or unlocked. As you mention above about QualComm Secure boot :Enable. may be before you was using gt-i9300 firmware it must be unlocked but after you flashed wrong firmware may be your bootloader got locked.
try to download complete stock 4.3 firmware from sammobile.com for correct variant i.e GT-I9300.
Download it and extract it and you will get .tar files
download latest Odin ( google it ) and open it.
put your phone in download mode by pressing volume down + home key + power key for few deconds until download mode screen appear.
press volume up key to goto download mode. connect your phone to your computer and wait till it install all the necessary driver. if you drivers are not installed properly then you have to manually installe the driver for your phone. download galaxy toolkit for s3 from xda and install it. search for the folder name galaxy toolkit in your computer. basically it will be in c:/ drive. open that folder and you will find driver folder under it. Inside the driver folder there will .exe file of driver. but before installing disconnect your phone computer and then install the driver. after the installation of your driver plug in again and wait till it install all the drivers.
Inside odin you must have to see that there is COM ID in 1st box and below it is written attached. if you dont see that then your driver are not installed correctly. uninstall and install it again.
after the driver install click on AP and select the AP .tar file that we extracted after downloading. select the appropriate file associated with it.
click on start and wait few minutes till the process gets complete.
If all things goes right you may get your phone back again.
Click to expand...
Click to collapse
Thank you for the response.
Drivers work and it's been able to connect to ODIN but it fails regardless of the stock firmware I flash via PDA.
I get this :
<ID:0/006> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9300XXBLH1_I9300OLBBLH1_I9300DXLH1_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/006> Odin v.3 engine (ID:6)..
<ID:0/006> File analysis..
<ID:0/006> SetupConnection..
<ID:0/006> Initialzation..
<ID:0/006> Get PIT for mapping..
<ID:0/006> Firmware update start..
<ID:0/006> system.img
<ID:0/006> NAND Write Start!!
<ID:0/006> FAIL!
<OSM> All threads completed. (succeed 0 / failed 1)
For Bootloader
<ID:0/006> Removed!!
<ID:0/006> Added!!
<ID:0/006> Odin v.3 engine (ID:6)..
<ID:0/006> File analysis..
<ID:0/006> SetupConnection..
<ID:0/006> Initialzation..
<ID:0/006> Get PIT for mapping..
<ID:0/006> Firmware update start..
<ID:0/006> sboot.bin
<ID:0/006> NAND Write Start!!
<ID:0/006> FAIL!
<OSM> All threads completed. (succeed 0 / failed 1)
----
It would help to mention that I have a second i9300 that works and hasn't been touched or anything. Can I do something with that?
edit* It says unsupported dev type on my screen when it fails..
simonheros said:
Thank you for the response.
Drivers work and it's been able to connect to ODIN but it fails regardless of the stock firmware I flash via PDA.
I get this :
<ID:0/006> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9300XXBLH1_I9300OLBBLH1_I9300DXLH1_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/006> Odin v.3 engine (ID:6)..
<ID:0/006> File analysis..
<ID:0/006> SetupConnection..
<ID:0/006> Initialzation..
<ID:0/006> Get PIT for mapping..
<ID:0/006> Firmware update start..
<ID:0/006> system.img
<ID:0/006> NAND Write Start!!
<ID:0/006> FAIL!
<OSM> All threads completed. (succeed 0 / failed 1)
For Bootloader
<ID:0/006> Removed!!
<ID:0/006> Added!!
<ID:0/006> Odin v.3 engine (ID:6)..
<ID:0/006> File analysis..
<ID:0/006> SetupConnection..
<ID:0/006> Initialzation..
<ID:0/006> Get PIT for mapping..
<ID:0/006> Firmware update start..
<ID:0/006> sboot.bin
<ID:0/006> NAND Write Start!!
<ID:0/006> FAIL!
<OSM> All threads completed. (succeed 0 / failed 1)
----
It would help to mention that I have a second i9300 that works and hasn't been touched or anything. Can I do something with that?
edit* It says unsupported dev type on my screen when it fails..
Click to expand...
Click to collapse
Looks like your Nand maybe corrupt try flashing the rescue firmware >> http://forum.xda-developers.com/showpost.php?p=30087735 <<
tallman43 said:
Looks like your Nand maybe corrupt try flashing the rescue firmware >> http://forum.xda-developers.com/showpost.php?p=30087735 <<
Click to expand...
Click to collapse
<ID:0/006> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> BOOTLOADER_I9300XXEMG4_1314436_REV00_user_low_ship.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> CODE_I9300XXEMG4_1314436_REV00_user_low_ship.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> MODEM_I9300XXEMG4_1314436_REV00_user_low_ship.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> CSC_I9300OXAEMG4_KOR_FACTORY_user_low_ship.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/006> Odin v.3 engine (ID:6)..
<ID:0/006> File analysis..
<ID:0/006> SetupConnection..
<ID:0/006> Initialzation..
<ID:0/006> Set PIT file..
<ID:0/006> DO NOT TURN OFF TARGET!!
<ID:0/006> Get PIT for mapping..
<ID:0/006> Firmware update start..
<ID:0/006> sboot.bin
<ID:0/006> NAND Write Start!!
<ID:0/006> FAIL!
<OSM> All threads completed. (succeed 0 / failed 1)
SECURE CHECK FAIL : PIT
Unsupport: dev_type
---
None of the PIT's work now... And pretty much none of the files passed... D:
simonheros said:
<ID:0/006> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> BOOTLOADER_I9300XXEMG4_1314436_REV00_user_low_ship.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> CODE_I9300XXEMG4_1314436_REV00_user_low_ship.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> MODEM_I9300XXEMG4_1314436_REV00_user_low_ship.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> CSC_I9300OXAEMG4_KOR_FACTORY_user_low_ship.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/006> Odin v.3 engine (ID:6)..
<ID:0/006> File analysis..
<ID:0/006> SetupConnection..
<ID:0/006> Initialzation..
<ID:0/006> Set PIT file..
<ID:0/006> DO NOT TURN OFF TARGET!!
<ID:0/006> Get PIT for mapping..
<ID:0/006> Firmware update start..
<ID:0/006> sboot.bin
<ID:0/006> NAND Write Start!!
<ID:0/006> FAIL!
<OSM> All threads completed. (succeed 0 / failed 1)
SECURE CHECK FAIL : PIT
Unsupport: dev_type
---
None of the PIT's work now... And pretty much none of the files passed... D:
Click to expand...
Click to collapse
Any progress??
suyash1629 said:
Any progress??
Click to expand...
Click to collapse
None what so-ever. I hit a dead end and had to get a replacement.
I'm just not going to mess with the new one anymore...
I have a Samsung s7 stuck on the front page with frp lock, I made a mistake while installing a custom rom. I am trying to install a stock rom: but all I get is odin cant get through serial port or Complete write operation failed. The most common response is it cant get through the serial(com) port. FAILED.(Many Many Many times) I have tried different usb port, reinstalled usb drives, don't have kies do it cant clash with that The last one I did came up with this.
SM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Added!!
<ID:0/003> Odin engine v(ID:3.1301)..
<ID:0/003> File analysis..
<ID:0/003> Total Binary size: 4195 M
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Set PIT file..
<ID:0/003> DO NOT TURN OFF TARGET!!
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> NAND Write Start!!
<ID:0/003> SingleDownload.
<ID:0/003> sboot.bin
<ID:0/003> FAIL!
<ID:0/003>
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/003> Odin engine v(ID:3.1301)..
Can you help. I am beginning to think I will have to buy a new phone. I have all version on odin from 6 to 13. Several verions of stock firmware for samssung s7 sm-g930f and many twrp.
WHat am I doing wrong?????????????????????????????
Hi , you can try one of this steps : )
1. Reset COM ports:
http://blog.cognitioninfotech.com/2009/01/how-to-clear-or-reset-com-port.html
2. Uninstall all drivers for your device like Android , MTP driver , adb driver , etc....
Use USBDeview toll to uninstall hidden drivers .
32 bit:
https://www.nirsoft.net/utils/usbdeview.zip
64 bit:
https://www.nirsoft.net/utils/usbdeview-x64.zip
3. Download latest version of ODIN
https://odindownload.com/download/Odin3_v3.13.1.zip
4. Make sure that Windows Update is Avtivated and also make sure that PC drivers for usb is updated or just reinstall them.
5. Disable Antivirus protection , and Reset Windows Firmware to Default settings .
6. Use Original cable , and usb 2.0 ports from back .
7. If you was using Android 7 with security patch from April 2018 , flash this combination firmware once your COM port is show up.
https://drive.google.com/uc?export=download&id=1M9T2tii3JcYZQ1YbP54dPiQI8hNrytOx
An example of how it should look:
https://www.youtube.com/watch?v=aCDgGF7VvY8
7. If that doesn't help you make sure you are using Latest stock firmware , otherwise flashing with always fail !
To make sure you are using right firmware send me 7 and 8 number from IMEI number : ) .
Good luck