Cannot root stock 4.0.4 - AT&T Samsung Galaxy Note I717

Had my device replaced by AT&T and came with 4.0.4 and I cannot root it. The non-counter increasing method says it's only for GB so I am left with the Odin method of flashing CWM.
But it's not working. I click start and all it does is say this :
<ID:0/014> Added!!
<ID:0/014> Odin v.3 engine (ID:14)..
<ID:0/014> File analysis..
<ID:0/014> SetupConnection..
<ID:0/014> Initialzation..
<ID:0/014> Get PIT for mapping..
<ID:0/014> Firmware update start..
<ID:0/014> recovery.img
And continues no further.
Can any one offer any ideas?

rootgalaxynote dot com go there very easy method.
Sent from my SAMSUNG-SGH-I717 using xda premium

magecca said:
Had my device replaced by AT&T and came with 4.0.4 and I cannot root it. The non-counter increasing method says it's only for GB so I am left with the Odin method of flashing CWM.
But it's not working. I click start and all it does is say this :
<ID:0/014> Added!!
<ID:0/014> Odin v.3 engine (ID:14)..
<ID:0/014> File analysis..
<ID:0/014> SetupConnection..
<ID:0/014> Initialzation..
<ID:0/014> Get PIT for mapping..
<ID:0/014> Firmware update start..
<ID:0/014> recovery.img
And continues no further.
Can any one offer any ideas?
Click to expand...
Click to collapse
http://forum.xda-developers.com/showthread.php?t=1740367
are you using the correct ver first, see thread above for Rooting tools, k

bigjoe2675 said:
http://forum.xda-developers.com/showthread.php?t=1740367
are you using the correct ver first, see thread above for Rooting tools, k
Click to expand...
Click to collapse
That would have been my guess too-wrong version.
Sent from my SAMSUNG-SGH-I717 using Tapatalk 2

That is the thread I referred to when attempting my root.
Wrong version of CWM?

magecca said:
That is the thread I referred to when attempting my root.
Wrong version of CWM?
Click to expand...
Click to collapse
not the wrong version, but maybe a bad copy of it ??
The PC environment is critical to this process, and often times, the files have conflicts..
Temporary shut down of any anti-virus software, HTC sync, etc. will help in the process.
Also, make sure you are using a powered rear USB port on the PC, and the factory cable if possible.
If problems still persist, re-download the files again, Odin included....g

magecca said:
That is the thread I referred to when attempting my root.
Wrong version of CWM?
Click to expand...
Click to collapse
This is the version Bigjoe was pointing you to.
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Is that what you used?
Usb debugging on phone checked?
Stock charging cable?
Phone in download mode?

Yes, that was the file I used.
It must have been something computer specific because I downloaded the same files to my office computer and it worked; come to think of it, I've always done it from my office computer.
Thank you all for your help!

I knew It !!!.....LOL
Congratulations !!
your rockin the note now !!....g

You Guys Rock!
gregsarg said:
......
Click to expand...
Click to collapse
rangercaptain said:
......
Click to expand...
Click to collapse

I just knocked my monitor onto the floor...
those internet high fives are wicked !!....LOL

gregsarg said:
I just knocked my monitor onto the floor...
those internet high fives are wicked !!....LOL
Click to expand...
Click to collapse
Lmao!
Sent from my GNote using Forum Runner, on Black ★.

Related

adb says my device is offline.

I've isntalled the 64 bit samsung drivers adb sdk odlin, rebooted a hand full of times. But adb wont recognize my device as being online. Its there it shows in adb but its offline. What do I do now...
ludeboye said:
I've isntalled the 64 bit samsung drivers adb sdk odlin, rebooted a hand full of times. But adb wont recognize my device as being online. Its there it shows in adb but its offline. What do I do now...
Click to expand...
Click to collapse
lude youve been at this a while now . Did you check USB debbuging in settings , applications , USB setting ?
Sometimes this happens to me and I have to switch usb ports then it will recognize the phone. Out reboot your computer.
Sent from my SGH-T959 using XDA App
AgentFour20 said:
lude youve been at this a while now . Did you check USB debbuging in settings , applications , USB setting ?
Click to expand...
Click to collapse
Yes debugging on, going to switch usb ports now.
I think plugging it into the 3.0 usb port in the back worked. The front once didnt
I've done it, if when I get rich ill buy a hooker for everyone that helped me. YAYAYAYA!
Wow I think I ****ed up this is what it said after getting in download mode and trying to connect to odlin for ji6 update.
<ID:0/005> Added!!
<ID:0/005> Odin v.3 engine (ID:5)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> cache.rfs
<ID:0/005> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/005> Removed!!
Phone wont power up now...
I got a phone to computer icon with a acclimation mark in the middle.
I can still get in download mode but when I try to update the new ji6 same error, I am on com port 4 too...
This is what I have
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Alright I got into download mode again and tried to upload the ji6 again on com3 everything went ok the phone boots up fine now. That scared the **** out of me
ludeboye said:
Alright I got into download mode again and tried to upload the ji6 again on com3 everything went ok the phone boots up fine now. That scared the **** out of me
Click to expand...
Click to collapse
Congrats
Sent from my SGH-T959 using XDA App

How can i downgrade to 2.3.6 from 4.0.3 Using ODin

Iv rooted and flashed my S2 Using Odin. And now unable too connect to PC via USB. is there anyway of reflashing the phone to 2.3.6 from 4.0.3 Using Odin in Download Mode.
b33v3r said:
Iv rooted and flashed my S2 Using Odin. And now unable too connect to PC via USB. is there anyway of reflashing the phone to 2.3.6 from 4.0.3 Using Odin in Download Mode.
Click to expand...
Click to collapse
Yes
But how are you going to flash if you have no USB mode .
Search might help .
jje
I can get in into DOWNLOAD Mode using ODIN and the phone will connect
b33v3r said:
I can get in into DOWNLOAD Mode using ODIN and the phone will connect
Click to expand...
Click to collapse
Flash a stock rom as per all the threads posts faqs and guides .
jje
<ID:0/009> Odin v.3 engine (ID:9)..
<ID:0/009> File analysis..
<ID:0/009> SetupConnection..
<ID:0/009> Initialzation..
<ID:0/009> Set PIT file..
<ID:0/009> DO NOT TURN OFF TARGET!!
<ID:0/009> Can't open the specified file. (Line: 1876)
b33v3r said:
<ID:0/009> Odin v.3 engine (ID:9)..
<ID:0/009> File analysis..
<ID:0/009> SetupConnection..
<ID:0/009> Initialzation..
<ID:0/009> Set PIT file..
<ID:0/009> DO NOT TURN OFF TARGET!!
<ID:0/009> Can't open the specified file. (Line: 1876)
Click to expand...
Click to collapse
Try this guide and download the right firmware you need. http://forum.xda-developers.com/showthread.php?t=1075278
Cheers!
b33v3r said:
<ID:0/009> Odin v.3 engine (ID:9)..
<ID:0/009> File analysis..
<ID:0/009> SetupConnection..
<ID:0/009> Initialzation..
<ID:0/009> Set PIT file..
<ID:0/009> DO NOT TURN OFF TARGET!!
<ID:0/009> Can't open the specified file. (Line: 1876)
Click to expand...
Click to collapse
This sounds like the .tar file you are using is corrupted maybe. You may need to re-download it.
What file did you download and where did you get it from? What guide are you following?
Problem sorted yay
wisconsindesi said:
Try this guide and download the right firmware you need. http://forum.xda-developers.com/showthread.php?t=1075278
Cheers!
Click to expand...
Click to collapse
ahah silly me was trying to flash using i9000 stock sorted now using the right stock rom
b33v3r said:
ahah silly me was trying to flash using i9000 stock sorted now using the right stock rom
Click to expand...
Click to collapse
Yikes. You're lucky you didn't do some serious damage to your phone.
For doing this downgrade, do you need to use the PIT or something else?
Or just the standard ODIN config?
Is just this or more (http://forum.xda-developers.com/showthread.php?t=1075278):
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Also, could I just use CWM to flash... lets say CheckROM (http://checkrom.com/download/)?
this is my first post.
how do i flash using Odin the file that i have downloaded which is superatmos_kernel_v2.2.tar. do i open the file with PDA only and flash it? or there are some other ways...
any inputs will be appreciated... sorry for noob question.. im just new here... and hoping somebody could help me.
adelbertheaven said:
this is my first post.
how do i flash using Odin the file that i have downloaded which is superatmos_kernel_v2.2.tar. do i open the file with PDA only and flash it? or there are some other ways...
any inputs will be appreciated... sorry for noob question.. im just new here... and hoping somebody could help me.
Click to expand...
Click to collapse
Your question is really way off topic.
Are you first sure the .tar is correct for your phone?
You should ask and read the instalation instructions from the developer first.

[Q] Can't install official ROM missing pit file

Okay so here's the thing:
I installed clockworkmod 10.1 on my Samsung Galaxy S3 (UK version) the other day it worked fine however it then froze. I turned it off and then when I proceeded to turn it back on I was greeted with a white screen. I have tried to access recovery mode however the same white screen is just shown.
Although I cannot access recovery mode download mode is accessible however when I try to use Odin to flash a rom an error is shown saying
<ID:0/004> Added!!
<ID:0/004> Odin v.3 engine (ID:4)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Set PIT file..
<ID:0/004> DO NOT TURN OFF TARGET!!
<ID:0/004>
<ID:0/004> Re-Partition operation failed.
I have tried many different pit files and I don't know whether I have just got the wrong one!
Please help!
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Can you get into recovery?
I can't get into anything except download mode!
If you can't may I suggest you try flashing one of the low ship formatted from this thread, it should put you back to your stock original firmware
http://forum.xda-developers.com/showthread.php?t=1796062
Low ship I9300 firmware for flashing with PIT. (three files firmware)
Calumt6 said:
Okay so here's the thing:
I installed clockworkmod 10.1 on my Samsung Galaxy S3 (UK version) the other day it worked fine however it then froze. I turned it off and then when I proceeded to turn it back on I was greeted with a white screen. I have tried to access recovery mode however the same white screen is just shown.
Although I cannot access recovery mode download mode is accessible however when I try to use Odin to flash a rom an error is shown saying
<ID:0/004> Added!!
<ID:0/004> Odin v.3 engine (ID:4)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Set PIT file..
<ID:0/004> DO NOT TURN OFF TARGET!!
<ID:0/004>
<ID:0/004> Re-Partition operation failed.
I have tried many different pit files and I don't know whether I have just got the wrong one!
Please help!
Click to expand...
Click to collapse
Your phone is basically screwed mate
stupidly will be met by sarcasm
Have you tried flashing a parted firmware with a pit file?
http://forum.xda-developers.com/showpost.php?p=30087735&postcount=6
If one of those don't work, then I don't know.
Correct me if i am wrong but im prerty sure flashing an incorrect pit file bricks the phone. You can take it to a service centre but its a paid for repair.
Vengeance
Sent from my GT-I9300 using xda app-developers app
correct
please guide me I have an i9300 it doesnt enter to recovery mode but it enter to downloading mode
It doesnt show gt-i9300 in front of product name
aminrezaya said:
please guide me I have an i9300 it doesnt enter to recovery mode but it enter to downloading mode
It doesnt show gt-i9300 in front of product name
Click to expand...
Click to collapse
I assume flashing a stock ROM with a pit file didn't work? nothing you can do
aminrezaya said:
please guide me I have an i9300 it doesnt enter to recovery mode but it enter to downloading mode
It doesnt show gt-i9300 in front of product name
Click to expand...
Click to collapse
SDS imho. Nothing you can do about. Send it to Service Point.
Sent from my GT-I9305 using xda app-developers app
djembey said:
SDS imho. Nothing you can do about. Send it to Service Point.
Sent from my GT-I9305 using xda app-developers app
Click to expand...
Click to collapse
I live in a country which has no service point... what can I do?
Any solution ? no product name when it enter to downloading mode
aminrezaya said:
I live in a country which has no service point... what can I do?
Any solution ? no product name when it enter to downloading mode
Click to expand...
Click to collapse
have you tried flashing anything with odin or not? if it fails, there is nothing you can do
Yes I tried 4.1.2 one file but it shows there is no PIT partition
so have you tried flashing a pit file?
Okay so I tried everything and nothing worked!
I thought I'd risk it and send it to Samsung to fix.
They collected on Tuesday, fixed on Wednesday, then returned on Thursday, I was amazed!
Thanks for all your replies and suggestions though

[Q] yellow triangle issue

i was updating my mobile in download mode.in the odin software it freezed on setup connection and then it shown me fail then i removed the usb cable and i couldnt shutdown my mobile from download mode i remove the battery after that when i get my phone on there's a yellow triangle between the symbols of a cellphone and PC.
please help.
yeah...you just dont remove the usb during a flash....
That's forced download, plug the device to the pc and flash a ROM meant for your device.
We don't even know what model you own neither what you're trying to flash.
Sent from the little guy
gastonw said:
yeah...you just dont remove the usb during a flash....
That's forced download, plug the device to the pc and flash a ROM meant for your device.
We don't even know what model you own neither what you're trying to flash.
Sent from the little guy
Click to expand...
Click to collapse
i removed the usb cable after the failed warning of odin. and my mobile model number is i9100g and the rom supported farsi language.i mean the mobile was for middle east
Maybe this would help:
http://forum.xda-developers.com/showthread.php?t=2251618
Any I9100G ROM is good for you, just make sure it's meant for I9100G.
Sent from the little guy
i was updating the original rom to the official jellybean of samsung for i9100g.
by the way i tried again and the log of odin is :
<ID:0/003> Added!!
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> boot.bin
<ID:0/003> NAND Write Start!!
<ID:0/003>
<ID:0/003> Complete(Write) operation failed.
<ID:0/003> Added!!
<OSM> All threads completed. (succeed 0 / failed 1)
shoud i flash with stock rom?
because i tried that with official jelly bean again
please help me
Check this thread. http://forum.xda-developers.com/showthread.php?t=2243231
Notice that the device with issues is an I9100. Pay attention to the suggestions in on how to get odin to pass, NOT on what FILES to flash.
Get your I9100G gear ( I9100G ROMs and kernels and flash those instead).
Sent from the little guy
gastonw said:
Check this thread. http://forum.xda-developers.com/showthread.php?t=2243231
Notice that the device with issues is an I9100. Pay attention to the suggestions in on how to get odin to pass, NOT on what FILES to flash.
Get your I9100G gear ( I9100G ROMs and kernels and flash those instead).
Sent from the little guy
Click to expand...
Click to collapse
ok.thank you very much but the last question.
im not in the download mode and i told you about that symbols can i flash when im not in the download mode or these symbols are from download
could you get my meaning?
Those symbols mean that your phone is practically begging you to flash something. It's called forced download.
Sent from the little guy
so i have driver issue.
i google every where on the internet but they are all lame.
could you give me the link of galaxy s2 usb driver.:good:
get latest kies.
It might be a bad ROM flash tho.
Those threads are meant to ve a guide.
You need to get your pc to see the device, then flash a proper stock I9100G ROM.
Sent from the little guy
Forced download mode:
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Download mode:
Both can be used to flash via Odin.
Posted here just in case someone reading this thread has any doubts.
"To err is human, to forgive is divine"
Sent from my SGS II

[Q] Odin Bootloop VZW i545 after TWRP flash from goo manager

can be deleted. resolved!
daign said:
So I am stuck in Odin Bootloop into the downloading screen. I am trying to refllash the stock firmware
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
The message log from odin says:
Enter CS for MD5..
Check MD5.. Do not unplug the cable..
Please wait..
SCH-I545_MDK_562219_Stock_Restore.tar.md5 is valid.
Checking MD5 finished Sucessfully..
Leave CS..
Added!!
Odin v.3 engine (ID:15)..
File analysis..
SetupConnection..
All threads completed. (succeed 0 / failed 1)
Removed!!
Added!!
Odin v.3 engine (ID:15)..
File analysis..
SetupConnection..
Initialzation..
Erase...
Set PIT file..
DO NOT TURN OFF TARGET!!
Get PIT for mapping..
Firmware update start..
sbl1.mbn
NAND Write Start!!
sbl2.mbn
sbl3.mbn
rpm.mbn
aboot.mbn
FAIL! (Auth)
I have tried rebooting the phone into recovery and it always goes into Odin. So I've got a bricked phone until I can figure this out.
Thanks for any advice you may be able to go give!
-D
Click to expand...
Click to collapse
You cant flash a custom recovery on me7. I would read a little bit next time I think this has been posted three times today. Youll have to flash the stock me7 image to get back the stock recovery. Everytime you try to boot to recovery youll get put in download mode. You can boot normally by using the button combo for download mode and then denying it.
You also dont flash a stock restore file under bootloader you flash it under pda.
Sent from my SCH-I545 using Tapatalk 2
hexitnow said:
You cant flash a custom recovery on me7. I would read a little bit next time I think this has been posted three times today. Youll have to flash the stock me7 image to get back the stock recovery. Everytime you try to boot to recovery youll get put in download mode. You can boot normally by using the button combo for download mode and then denying it.
You also dont flash a stock restore file under bootloader you flash it under pda.
Sent from my SCH-I545 using Tapatalk 2
Click to expand...
Click to collapse
Thanks. Got that resolved a while ago! :good:

Categories

Resources