Related
Guys, i was upgrading the ROM but this time i used this software, UNIFLASH , it showed some cmd windows, later phone automatically booted to cwm, and then turned off! since then its not turning on neither blinking any LED! guys, please show me a ray , help me! phone is not getting recognized by flashtool either :'( and same with seus
try to hold down power + volume up at the same time until you get the phone to vibrate 3 times, after that try to boot or get it into flashmode with flashtool..
remember.. flashtool is the way to go !
kindly report back or even pm me
realfelix said:
try to hold down power + volume up at the same time until you get the phone to vibrate 3 times, after that try to boot or get it into flashmode with flashtool..
remember.. flashtool is the way to go !
kindly report back or even pm me
Click to expand...
Click to collapse
already tried that, googled a lot already, nothing is helping!
also tried doing what you said with USB connected through my pc, windows kept playing that system sound which comes up when we plus out a device! in particular time intervals, like 3 4 seconds.
bhuvangaur said:
already tried that, googled a lot already, nothing is helping!
also tried doing what you said with USB connected through my pc, windows kept playing that system sound which comes up when we plus out a device! in particular time intervals, like 3 4 seconds.
Click to expand...
Click to collapse
have you tried the fastboot method, it´s in android development, "all you need to know..."
try to flash official stock fw like .452 or .45 with flashtool..try to connect the phone in flashmode....hopefully everything will be alright...
PEACE
guys, phone is not able to boot in any mode, it be fastboot or flashmode! its completely dead thats what i meant earlier. After a lot of researching the whole night, i was able to figure out that the bootloader is that the UNIFLASH corrupted the bootloader. So how to fix that?
try this: make sure you have enough charge and the drivers of your phone are installed correctly. (flashtool drivers)
power+volume up wait till vibrates three times,
then connect your phone to pc.
run the flashtool and prepare the firmwares youre going to flash,
a screen will appear and says turn off your phone....etc
hold power button + volume up wait till vibrates three times
then quickly hold power button + volume down.
it will flash the firmware.
just keep on trying.
mharckk said:
try this: make sure you have enough charge and the drivers of your phone are installed correctly. (flashtool drivers)
power+volume up wait till vibrates three times,
then connect your phone to pc.
run the flashtool and prepare the firmwares youre going to flash,
a screen will appear and says turn off your phone....etc
hold power button + volume up wait till vibrates three times
then quickly hold power button + volume down.
it will flash the firmware.
just keep on trying.
Click to expand...
Click to collapse
its simply not vibrating! i held that combination for like 5 minutes continuous last night, phone has to enter either fastboot or flashmode for flashtool to detect! none of them is coming up, and no LED again when its on charging. complete dead complete mess!
By the way, anyone knows how service center people update the phone's software?
bhuvangaur said:
its simply not vibrating! i held that combination for like 5 minutes continuous last night, phone has to enter either fastboot or flashmode for flashtool to detect! none of them is coming up, and no LED again when its on charging. complete dead complete mess!
By the way, anyone knows how service center people update the phone's software?
Click to expand...
Click to collapse
Go to repair center or phone shop! These guys know how to rewrite ur bootloader through JTAG! Don't worry, u'll get it back once it's done!
Sent From my Lt26i, Hit thank whenever u like!
I think you hard bricked your device... Go to service centre ...
Sent from my LT22i using xda premium
i appreciate you guys for your replies! gave the phone to them yesterday, good to hear about JTAG, will surely revert here and let ya'll know about it! this might happen with any one in future, might help him too!
PS, since the company is no more ericsson based, new service center are SONY one only, where all sony products are welcomed, really good service center now! earlier it was sh*tty since years! i loved the experience this time
bhuvangaur said:
i appreciate you guys for your replies! gave the phone to them yesterday, good to hear about JTAG, will surely revert here and let ya'll know about it! this might happen with any one in future, might help him too!
Click to expand...
Click to collapse
would you please enplane what is JTAG and how it works ?
Had the same problem yesterday!
Maybe a noob advice but here what was my mistake: after switch off the phone with volume up, wait for like 30 second before trying to connect in flash mode. Though my phone was dead but just had to wait a little bit before trying the flash mode. Flashtool heal it!
Sorry for my poor english, I'm french and this is my first post, but I follow xda since a long time!
Bye!
Napolee said:
would you please enplane what is JTAG and how it works ?
Click to expand...
Click to collapse
It a type of connector that is use to connect directly to the phone mainboard. It use to transfer some specific data such as bootloader!
Sent From my Lt26i, Hit thank whenever u like!
this is hilarious!!! a replacement! brand new xperia s! yay!
Trying to Survive my LT26i
I have rooted my phone
put recovery and flashed my rom to xxperience
so everything was ok
using for 2days
so i saw how to overclocked to 1.8ghz and flash via cwm the kernel
after restart from cwm not either the screen turn on
just green light when i put cable on
and when i tried to flash via flash tool given error for error
so i done as say here to hold power + volume up, and the same
so i waited for a little time and try again and its flashing now...
hope it works
So i was transfering some files to my xperia p and all of a sudden i noticed that the transfer was hold up,at that point i tried waking up my phone but it wouldnt,i tried pressing the power button,the camera button and all that are avalible but to no success.So i tried to reboot the phone via the combination of Power+Volume UP buttons,and thats it.nothing else happens.It does not respond and so i tried to remove and reinsert the battery,and then the phone lit up with the sony logo and its been there for over and hour and ahalf.
PLEASE SOMEONE HELP ME!!!
k0k0t0 said:
So i was transfering some files to my xperia p and all of a sudden i noticed that the transfer was hold up,at that point i tried waking up my phone but it wouldnt,i tried pressing the power button,the camera button and all that are avalible but to no success.So i tried to reboot the phone via the combination of Power+Volume UP buttons,and thats it.nothing else happens.It does not respond and so i tried to remove and reinsert the battery,and then the phone lit up with the sony logo and its been there for over and hour and ahalf.
PLEASE SOMEONE HELP ME!!!
Click to expand...
Click to collapse
I think u need to flash stock ROM from flashtool first
Than use this app for transfering files
http://forum.xda-developers.com/showthread.php?t=1606940
merhan94 said:
I think u need to flash stock ROM from flashtool first
Than use this app for transfering files
http://forum.xda-developers.com/showthread.php?t=1606940
Click to expand...
Click to collapse
The problem is that the phone wont respond to anything.
PS: i cant unlock the bootloader,so i cant root and im on 4.1.2
k0k0t0 said:
The problem is that the phone wont respond to anything.
PS: i cant unlock the bootloader,so i cant root and im on 4.1.2
Click to expand...
Click to collapse
Did u try hold power button and volume up until phone vibrate 3 times?
No need for bootloader unlocked or root for flash new stock rom
merhan94 said:
Did u try hold power button and volume up until phone vibrate 3 times?
No need for bootloader unlocked or root for flash new stock rom
Click to expand...
Click to collapse
As i said in the first one,i tried it,sorry for not saying about the where it vibrates 2 with an interval of about 3-4 sec,and then 3 burst vibrations!
k0k0t0 said:
As i said in the first one,i tried it,sorry for not saying about the where it vibrates 2 with an interval of about 3-4 sec,and then 3 burst vibrations!
Click to expand...
Click to collapse
I don't know how to flash stock rom without power off the device.
Sorry I can't help you
http://forum.xda-developers.com/showthread.php?t=2081876
I unbricked my phone with this guide. my phone was in a OS bootloop but it works, in your case, a Kernel Bootloop. Its a very good guide. You DO NOT need to root your phone. When flashing, instead of pressing back you press volume down. The phone should be able to enter what it is called, flash mode regardless of what problems. After flashing ALL DATA WILL BE LOST. Just follow the guide.
AndroidNoob69 said:
http://forum.xda-developers.com/showthread.php?t=2081876
I unbricked my phone with this guide. my phone was in a OS bootloop but it works, in your case, a Kernel Bootloop. Its a very good guide. You DO NOT need to root your phone. When flashing, instead of pressing back you press volume down. The phone should be able to enter what it is called, flash mode regardless of what problems. After flashing ALL DATA WILL BE LOST. Just follow the guide.
Click to expand...
Click to collapse
tried didnt work so i just sent it for the waranty!
So I was trying to put a custom Rom on my Xperia and It bricked it, I unlocked the bootloader and installed cwm but I ****ed it up some how when installing the ROM. It won't turn on, nothing happens when i push the on button. doesn't vibrate or anything. When I plug it into my charger there is a red light but it goes away after about 15 minutes. I'm pretty sure its hard bricked, is there anything I can do? Suggestions are welcom. Should i send it to sony?
dagarnothmax said:
So I was trying to put a custom Rom on my Xperia and It bricked it, I unlocked the bootloader and installed cwm but I ****ed it up some how when installing the ROM. It won't turn on, nothing happens when i push the on button. doesn't vibrate or anything. When I plug it into my charger there is a red light but it goes away after about 15 minutes. I'm pretty sure its hard bricked, is there anything I can do? Suggestions are welcom. Should i send it to sony?
Click to expand...
Click to collapse
First of all: Sony will probably not help you since you unlocked the bootloader.
Next: Have you tryed to to connect to a computer using Flashtool?
TheSoleBulge said:
First of all: Sony will probably not help you since you unlocked the bootloader.
Next: Have you tryed to to connect to a computer using Flashtool?
Click to expand...
Click to collapse
Yeah, computer isn't detecting it or anything. just the red light
dagarnothmax said:
Yeah, computer isn't detecting it or anything. just the red light
Click to expand...
Click to collapse
Ok.. Holding down power button and volume up at the same time?
TheSoleBulge said:
Ok.. Holding down power button and volume up at the same time?
Click to expand...
Click to collapse
I've tried that and still nothing.
did you solve the problem?
Hi, i have problem with zenfone 5. My brother tried to install new android using wireless update in phone(auto update function). So the update downloaded just fine and phone was turned off like its gonna install update but never turned on after this, i tried everything but cant turn it on. I cant even get asus logo, absolutly nothing. When i turn it on charger led dosent show up, tried to enter droidmode(vol up + power) for 10min but nothing. My first guess will be dead MBO but its really weird that this is happen in same time the update was, so probably is something software related.
Bump
Sent from my iOCEAN X7 using Tapatalk
asus zenfone 5 wont turn on
we have same problem, I tried to wipe cache partition for battery consumption purposes but i cancelled it, it seems to long to process erasing the cache so i cancelled it by holding power button + volume up then, wont turn on, itried to charge it, while holding power button + volume up the asus logo appear after that, the battery logo display appear (white side and black battery)
exzzy said:
Hi, i have problem with zenfone 5. My brother tried to install new android using wireless update in phone(auto update function). So the update downloaded just fine and phone was turned off like its gonna install update but never turned on after this, i tried everything but cant turn it on. I cant even get asus logo, absolutly nothing. When i turn it on charger led dosent show up, tried to enter droidmode(vol up + power) for 10min but nothing. My first guess will be dead MBO but its really weird that this is happen in same time the update was, so probably is something software related.
Click to expand...
Click to collapse
hi i am having the exactly same problem, could you tell how did you solve it??
Please i need help.
thank you
Start the phone by pressing power key + volume up and then select the option reboot worked for me!!
Thank you..
It worked for me also, :good:
That's bootloop dude. You need to flash your phone using fastboot. Flash the latest firmware .60 lollipop
Cannot start the phone
AkcezzInc said:
That's bootloop dude. You need to flash your phone using fastboot. Flash the latest firmware .60 lollipop
Click to expand...
Click to collapse
Whats 'the latest firmware .60'? can explain to me how to install it.
Facing the same problem(zenfone 5 not gettting started after update)
Even fastboot is not working for reboot
Pls help...!!!!
Thanx...!!!
skm14747 said:
Even fastboot is not working for reboot
Pls help...!!!!
Thanx...!!!
Click to expand...
Click to collapse
U need to flash it with new rom via fastboot with adb command... flash recovery.img first then flash new rom... .. whatever u want to flash jb,kk or loli but i recommend u to jb 4.3 .
Hi hendikj
hendikj said:
U need to flash it with new rom via fastboot with adb command... flash recovery.img first then flash new rom... .. whatever u want to flash jb,kk or loli but i recommend u to jb 4.3 .
Click to expand...
Click to collapse
Could you please explain how to do this tasks as i am new to all these words. pls.
U need to charge u r device Press power + up volume boot into boot loader...unlock bootloader then reboot from fastboot mode...it works for me..
fastboot is not getting open
hendikj said:
U need to flash it with new rom via fastboot with adb command... flash recovery.img first then flash new rom... .. whatever u want to flash jb,kk or loli but i recommend u to jb 4.3 .
Click to expand...
Click to collapse
i'm not able to open fastboot after update
Thanks. It Worked for me !
williamzerner said:
Start the phone by pressing power key + volume up and then select the option reboot worked for me!!
Click to expand...
Click to collapse
wont turn on..
does anyone has a problem phone wont turn on even pressing power key + volume up.you hear the sound when you connected to pc...like your phone is restarted.you only hear the sound but no display.no led light.no vibration.
this problem came when i unlock bootloader then i restart my phone then it didnt turn it on..sory for my bad english
davidjay26 said:
wont turn on..
does anyone has a problem phone wont turn on even pressing power key + volume up.you hear the sound when you connected to pc...like your phone is restarted.you only hear the sound but no display.no led light.no vibration.
this problem came when i unlock bootloader then i restart my phone then it didnt turn it on..sory for my bad english
Click to expand...
Click to collapse
same here! :crying:
Same problem here
davidjay26 said:
wont turn on..
does anyone has a problem phone wont turn on even pressing power key + volume up.you hear the sound when you connected to pc...like your phone is restarted.you only hear the sound but no display.no led light.no vibration.
this problem came when i unlock bootloader then i restart my phone then it didnt turn it on..sory for my bad english
Click to expand...
Click to collapse
Same over here too, did you solve your problem?
Hi, guys
Flashed the unofficial Lineage 14.1 and by mistake SuperSUClassic for 6.0. Now it is bricked
No bootloader, just 2 buzzes after 10 sec when you pressing the power button.
Are there any means to restore the boot record?
Try to keep Vol Up and press Power button to go to recovery. Or if not, at least into Fastboot with Vol Down and Power. Once you are in TWRP, you know what to do.
valy_cta said:
Try to keep Vol Up and press Power button to go to recovery. Or if not, at least into Fastboot with Vol Down and Power. Once you are in TWRP, you know what to do.
Click to expand...
Click to collapse
Tried that - no luck.
Will try again...
pgavril said:
Tried that - no luck.
Will try again...
Click to expand...
Click to collapse
What about battery, was it above 50% at least?
Edit: Try also https://forum.xda-developers.com/le-max-2/how-to/guide-hard-brick-fix-qualcomm-hs-usb-t3492949
valy_cta said:
What about battery, was it above 50% at least?
Edit: Try also https://forum.xda-developers.com/le-max-2/how-to/guide-hard-brick-fix-qualcomm-hs-usb-t3492949
Click to expand...
Click to collapse
Thanks
definitely will try that
You cant brick a qualcomm device. Like said above, just put the CPU in qdloader mode. It will flash directly to the nand memory.
Started flashing , but accidentally USB cable got disconnected - now can't quit the QFL mode, probably bricked it finally, Still waiting for the battery to discharge
pgavril said:
Started flashing , but accidentally USB cable got disconnected - now can't quit the QFL mode, probably bricked it finally, Still waiting for the battery to discharge
Click to expand...
Click to collapse
Have you kept the Power button pressed for about 1 minute to exit this mode?
If the above doesn't work, why don't you flash it again? Still your into the QFL mode.
valy_cta said:
Have you kept the Power button pressed for about 1 minute to exit this mode?
If the above doesn't work, why don't you flash it again? Still your into the QFL mode.
Click to expand...
Click to collapse
Power button does not respond, device manager shows QFD device,
Flash says 7:31:24: {ERROR: OpenPort:4197 It took 10.01500000 seconds to open port. Which is longer than 3.000. This indicates your target is not stable
..
https://www.gizmochina.com/2016/11/20/leeco-x820-max-2-super-unbrick-guide/