Hi
Please assist in this regard, I rooted my device and installed Rom Manager, and tried to flash MIUI Rom. My devices rebooted but were stuck on the Moto boot screen. I tried system recovery by holding down volume+- & power button, and it indicated my device were locked. My battery is flat and I'm unable to charge the battery at all. firmware 65.1.40.XT910.MERetail.en.06 Android Ver : 2.3.6. How do I get my device to work again amd where can I find the original Rom to flash with RSD lite ???
You feedback would be much appreciated.
Regards.
http://forum.xda-developers.com/showthread.php?t=1539192
This should get you started. You can try an old school battery pull (yes it is possible to remove the back, just have to pry like hell)
EDIT: Found a video on youtube for exactly this scenario.
http://m.youtube.com/#/watch?featur...ch?v=QfT2Bejkcdk&feature=youtube_gdata_player
Good luck mate
Sent from my XT912 using xda premium
Team black hat adapter
shop.teamblackhat.info/Factory-Adapters-motadapt.htm
I recommend getting a tbh adapter. It lets you power the phone directly from USB even with a dead battery. After that you need to use RSD liter or a similar tool to fastboot he phone back to stock.
Resolved Problem !!!
Thanks a lot guys, i manage to fixx the problem, i made my own factory cable charge for 1 hour and flashed a stock ROM with RSD lit 5.7, works fine
Bricked Razr XT910
My razr xt910 is bricked,whenever i turn it on it goes to fastboot with the following message:Ap Fastboot Flash Mode (flash failure)
Battery Low(No matter how much i hcarge it) ,Please Need Help,
Bought From London
arendshp said:
Thanks a lot guys, i manage to fixx the problem, i made my own factory cable charge for 1 hour and flashed a stock ROM with RSD lit 5.7, works fine
Click to expand...
Click to collapse
lol... Am I high or did you just shoved 5v on your Razr 3.7v battery directly from the usb port?
please help me,the razr is bricked ,it says locked and rsd is not detecting it,ive been trying to unbrick for the last 4 hours.pleas help
arendshp said:
Thanks a lot guys, i manage to fixx the problem, i made my own factory cable charge for 1 hour and flashed a stock ROM with RSD lit 5.7, works fine
Click to expand...
Click to collapse
Your picture inspired me so I just made a factory cable, pretty easy.
Bricked MOTOROLA xt910s
Dear concerns,
I was using MOTO xt910s Korean, during the software updating its bricked and I didn’t take any recovery backup. 1st my phone start and struck on LOGO and also go to recovery mode, but after that I discussed with one developer and he has changed the KERNAL of my mobile, now it only on in AP fastboot Mode. I am so worried about my phone, please give me solid solution. And 1 thing more during all that its battery also dead, I am also searching new battery.
I am waiting for your best and earlier response.
Thanks & Regards,
Usman
usman.yousaf said:
Dear concerns,
I was using MOTO xt910s Korean, during the software updating its bricked and I didn’t take any recovery backup. 1st my phone start and struck on LOGO and also go to recovery mode, but after that I discussed with one developer and he has changed the KERNAL of my mobile, now it only on in AP fastboot Mode. I am so worried about my phone, please give me solid solution. And 1 thing more during all that its battery also dead, I am also searching new battery.
I am waiting for your best and earlier response.
Thanks & Regards,
Usman
Click to expand...
Click to collapse
Wipe cid with fastboot.Use CMD to flash a EU Jellybean.
Sent from my XT910 using xda app-developers app
Need Solution of bricked MOTO XT910S
我顶你个肺隔膜 said:
Wipe cid with fastboot.Use CMD to flash a EU Jellybean.
Sent from my XT910 using xda app-developers app
Click to expand...
Click to collapse
Dear i am not a developer, i am a noob, please provide me easy way to flash my phone. please support me i am so worried
usman.yousaf said:
Dear i am not a developer, i am a noob, please provide me easy way to flash my phone. please support me i am so worried
Click to expand...
Click to collapse
Maybe english is too bad to explain this..
http://pan.baidu.com/share/link?shareid=1379604126&uk=4010743545
Rember to wipe your Cid first.
Download this,extract all the files content inside to where your extraxted EU Fastboot file is.And run the 运行我.bat,this will flash the EU ROM to your phone.This thing may damge your phone(Im using it with no problem),I wont pay any responsibility to any damge to your data,hardware or anything.
Sent from my XT910 using xda app-developers app
How Did You Do This?
arendshp said:
Thanks a lot guys, i manage to fixx the problem, i made my own factory cable charge for 1 hour and flashed a stock ROM with RSD lit 5.7, works fine
Click to expand...
Click to collapse
I'm in the same situation and need to charge my bricked XT910. If I can only do it the way you did, I could take it from from there with returning to stock ROM. Please show me how you did this. Thanks!
Daddyoyah said:
I'm in the same situation and need to charge my bricked XT910. If I can only do it the way you did, I could take it from from there with returning to stock ROM. Please show me how you did this. Thanks!
Click to expand...
Click to collapse
Motorola Fastboot/Factory Programming Cables Links
Sent from my XT907 using Tapatalk
Related
Before some of you gets upset with me posting the same kind of question, please know that I looked at the forum everywhere plus some other forums and tried almost everything. Here's the summary.
I recently got Droid Razr Asia version and I upgraded to EU Retail rom n rooted it.
There was one problem that I noticed that only bluetooth was not working.
Checked online, and found out that it's the radio mismatch b/w EU and Asia version.
So I downloaded RAZRX rom and was trying to flash it again with bootstrap.
So the process started and in 10 seconds it failed.
So I tried to search other forums ...
at some place i found that ... after Hard Resetting, clearing catche; I am also supposed to format the system.
So I followed the whole procedure, and turns out that again it does not get FLASHED. So I downloaded the ASIA version again and tried to format. It did not work. I tried with EU version, it did not work.
So after getting tired, I tried with RSDLite to flash through PC.
That's when I found out that ...
It detects the phone ... but the phone has no EMEI, software version or any other details. Everything is n/a.
Still I tried, and it said "fastboot installation failed" or somethin like that.
And now my phone is stuck on red motorola logo.
I tried to power off and go to bootloader fastboot ...
and it says "Fastboot Locked ... Press power button to power down."
I tried with the DroidRazrUtility1.4 also ...
But it does not detect the phone.
I tried other few things I found online. But nothing worked.
I also drained the battery by keeping it aside to see if the fastboot gets unlocked, but it didn't work.
However, I haven't removed the battery yet. Cause I do not have the tools.
Please can somebody tell me step by step approach how to do this?
Because I haven't found out where I am going wrong in the given methods. and btw, I have followed everything exactly step by step.
Really appreciate any kind of help.
Thank you very much.
Try to flash with RSD Alternative
http://forum.xda-developers.com/showthread.php?t=1453660
Thanks a ton.
But will it still work if my AP FATBOOT mode says that "Device is Locked"
And the battery is on low?
samthehell said:
Thanks a ton.
But will it still work if my AP FATBOOT mode says that "Device is Locked"
And the battery is on low?
Click to expand...
Click to collapse
Probably not. I read on one of the forums there might be a way around the battery being low. I think it was here in xda. Do a search for fast boot install or battery, something like that. If you find that doesn't work you would have to make the tbh cable which allows power to the phone without a battery, or in your case a near dead battery.
Sent from my Droid Razr using Tapatalk
"Device is locked" is natural, (almost) all of our bootloaders are locked. Nothing to do with flashing official ROMs.
You'll need to make a factory cable if the battery is low, search the development forum for a guide.
Sent from my XT910 using xda premium
Thank you all ... Just ordered the cable. Hope it works.
Appreciate all the help.
samthehell said:
Thank you all ... Just ordered the cable. Hope it works.
Appreciate all the help.
Click to expand...
Click to collapse
Here is where u can find full 2.3.6 Asian fastboot file, so you can use rsd for flashing 2.3.6 but for flashing 2.3.5 you have to use Alternative rsd because of bl version
http://forum.xda-developers.com/showthread.php?p=22821170
Sliced by my Razr on Tapatalk
hello, yesterday i wanted to flash a new rom.
i made full wipe, deleted cache and dalvik cache.
and i made a restart before flashing the new rom.
now i get the message: device is locked, status code:0
battery ok
ok to program
transfer mode:
usb connected
what can i do to rescue the phone ? it has been bought 3 weeks ago in germany for 489 euro.
All razrs currently have the locked status, it's referring to the boot loader which moto has declined to unlock.
Sent from my XT910 using xda premium
is there no way to get it unlocked ?
489 has been paid 3 weeks ago. the phone is only 3 weeks old. it has been used for 1 week ((
kirmizibasliklioglan said:
is there no way to get it unlocked ?
489 has been paid 3 weeks ago. the phone is only 3 weeks old. it has been used for 1 week ((
Click to expand...
Click to collapse
Can you charge the battery?
It's normal, nothing wrong happened.
At this time you can flash a new compatibile rom via RSD
hello, i can charge the battery. there is no problem. but i can not find a compitable rom. i have tried 2 different roms, unsuccesfull. i always get an error message after a few steps. the phone is connected, drivers are installed, but there is no compitable rom do you have a link for me ?
kirmizibasliklioglan said:
hello, i can charge the battery. there is no problem. but i can not find a compitable rom. i have tried 2 different roms, unsuccesfull. i always get an error message after a few steps. the phone is connected, drivers are installed, but there is no compitable rom do you have a link for me ?
Click to expand...
Click to collapse
Go Motorola Suport Website and look for Warranty. Provide your IMEI number and you'll get the service provider (carrier) you phone is attached. Then you'll know wich rom to flash.
Motorola Support - Warranty Status
hi thank you for the link. motorola germany can not help me because the device has been rooted, they told.
now i can not charge the battery. battrery low is to see on the display
i can connect my phone to pc but i dont know how and which rom i can flash
kirmizibasliklioglan said:
hi thank you for the link. motorola germany can not help me because the device has been rooted, they told.
now i can not charge the battery. battrery low is to see on the display
i can connect my phone to pc but i dont know how and which rom i can flash
Click to expand...
Click to collapse
But can you normally reboot your phone now?
You need to recharge before attempting to flash.
If you can't do this, try this link. I don't know if it works
http://forum.xda-developers.com/showthread.php?t=1549625
I think you can flash 651.167.26 or .19/20. You can find it on Motorola official roms thread
http://www.android-hilfe.de/root-hacking-modding-fuer-motorola-razr/232299-factory-adapter.html
5€ and your Phone will be fine...
To charge your phone: Click the link
To load a stock ROM: Click the link
If you still have questions, there's usually someone here.
okay, i believe i have solved this problem.
i have opened the back cover, cut the usb cable (from my old htc)
connected black to minus
connecten red to plus and plugged in to power...
after 5 minutes battery was ok, instead of "battery low"
i have uninstalled the old rsd lite
downloaded rsd lite v5.6
downloaded "SPDREM_U_01.6.5.1-167_SPU-15-M2_SIGNEuropeAustraliaEMEA_USASPDRRTGB_HWp2b_Service1FF_fastboot.xml" sorry, i don´t know the link
i have pressed volume down, volume up and power button.
selected fastboot mode.
started rsd lite
selected the "spdrem_u_..." file
and pressed start. it took about 15 minute
i will upload a few photos tonight
thank you for your help
kirmizibasliklioglan said:
hi thank you for the link. motorola germany can not help me because the device has been rooted, they told.
now i can not charge the battery. battrery low is to see on the display
i can connect my phone to pc but i dont know how and which rom i can flash
Click to expand...
Click to collapse
Get your IMEI in sdcard door of your razr then visit motorola support website I posted and you'll know wich rom to flash. You'll need to flash it with a factory cable as said above.
Good luck!
Sent from my XT910 using Tapatalk 2
kirmizibasliklioglan said:
okay, i believe i have solved this problem.
i have opened the back cover, cut the usb cable (from my old htc)
connected black to minus
connecten red to plus and plugged in to power...
after 5 minutes battery was ok, instead of "battery low"
i have uninstalled the old rsd lite
downloaded rsd lite v5.6
downloaded "SPDREM_U_01.6.5.1-167_SPU-15-M2_SIGNEuropeAustraliaEMEA_USASPDRRTGB_HWp2b_Service1FF_fastboot.xml" sorry, i don´t know the link
i have pressed volume down, volume up and power button.
selected fastboot mode.
started rsd lite
selected the "spdrem_u_..." file
and pressed start. it took about 15 minute
i will upload a few photos tonight
thank you for your help
Click to expand...
Click to collapse
nice to hear it worked. Cheers
Sent from my XT910 using Tapatalk 2
so i have spent hours trying to install a new rom from stock on 2.3.5.
I have bricked it loads and arrived at moto sunfire 2.3.5 using rsd.
i know that it is quite hard to flash a new rom install to the photon but i managed to complete install using an AOKP rom but after install a restart and then brick so back to the sunfire, I was wondering if someone can have a look at the install log and tell me what is going on and if there is a way of making it work? The bootloader is locked but installing using droid x2 recovery
THanks.
spindoctaa said:
so i have spent hours trying to install a new rom from stock on 2.3.5.
I have bricked it loads and arrived at moto sunfire 2.3.5 using rsd.
i know that it is quite hard to flash a new rom install to the photon but i managed to complete install using an AOKP rom but after install a restart and then brick so back to the sunfire, I was wondering if someone can have a look at the install log and tell me what is going on and if there is a way of making it work? The bootloader is locked but installing using droid x2 recovery
THanks.
Click to expand...
Click to collapse
you cant install a custom ROM on a phone with 2.3.5
foxsdaddy67 said:
you cant install a custom ROM on a phone with 2.3.5
Click to expand...
Click to collapse
yeah i can't get back to stock either. and have no gsm capabilities. i need some direction or help with where to go next.
i'm up to using the sunfire sbf and cannot flash a kernel etc. i have used droid x2 recovery which allowed an install using aroma installer. then it hard bricks and needs an rsd reset, then back to sunfire, but there is not a 2.3.5 official update from motorola or android that has worked either.
You can't install custom kernels or installers on locked 2.3.5. This is how to unbrick it back to sprint. Other than that you are pretty much out of luck. http://forum.xda-developers.com/showthread.php?t=1798145
ok i have tried that, now no charge on phone at all, it doesn't charge when plugging into the wall, when plugging it in to laptop with battery get just a green light, without get a white light, the noise to say device plugged in and then installing driver software for microboot. Any way forwards from this?
oh yeah, im in the UK so no warranty or anything.
Thanks
spindoctaa said:
ok i have tried that, now no charge on phone at all, it doesn't charge when plugging into the wall, when plugging it in to laptop with battery get just a green light, without get a white light, the noise to say device plugged in and then installing driver software for microboot. Any way forwards from this?
oh yeah, im in the UK so no warranty or anything.
Thanks
Click to expand...
Click to collapse
Look up USB wall charger hack. I can't remember which thread it's in. But essentially you're going to need a 5v usb wall charger and any old usb cable that you dont care about cutting and splicing. There will be 4 cables inside your usb cable. But you only need the Black and Red I think. Then you will need to directly connect the appropriate wires directly to the battery terminals t the correct polarity. I had to do it awhile ago when I bricked my phone and let the battery die. It works, trust me. Just gotta leaving it charging for a few hours. NM found the thread for you. http://forum.xda-developers.com/showthread.php?t=376299
hello everyone,
guys I am "desperate".
well, I was using the rom LiquidSmooth v2.4 on my razr XT910 was two weeks and everything was fine, so that before yesterday stopped recognizing my usb cable. I made several tests and ended up deleting my internal and external memory (pure stupidity), along with my backup. Now my phone does not pass the motorola logo screen, and I can only enter the Native motorola recovery.
My cel is not being recognized by the usb cable, or in fastboot, ie, do not have to use RSD.
With that, I wish someone, a good soul, can provide a nandroid of a rom to be performed via native razr recovery. (remembering that the rom I used was 4.2.2 jb and my cel is retail.en.eu)
Man, already tried everything, so I have left it. I can not lose this cel, I have no money to buy another (student is a sh all poor. Hehe)
if anyone has another idea of how to fix my cel is welcome.
if you can help me thank you very much ...
ps: very good initial video for noobs, kkkkk
ps ²: do not speak English very well, so I used google translator, sorry an error.
Rafael_Slomski said:
hello everyone,
guys I am "desperate".
well, I was using the rom LiquidSmooth v2.4 on my razr XT910 was two weeks and everything was fine, so that before yesterday stopped recognizing my usb cable. I made several tests and ended up deleting my internal and external memory (pure stupidity), along with my backup. Now my phone does not pass the motorola logo screen, and I can only enter the Native motorola recovery.
My cel is not being recognized by the usb cable, or in fastboot, ie, do not have to use RSD.
With that, I wish someone, a good soul, can provide a nandroid of a rom to be performed via native razr recovery. (remembering that the rom I used was 4.2.2 jb and my cel is retail.en.eu)
Man, already tried everything, so I have left it. I can not lose this cel, I have no money to buy another (student is a sh all poor. Hehe)
if anyone has another idea of how to fix my cel is welcome.
if you can help me thank you very much ...
ps: very good initial video for noobs, kkkkk
ps ²: do not speak English very well, so I used google translator, sorry an error.
Click to expand...
Click to collapse
I'm not sure if this will fix your problem, but do you have the proper drivers installed on your computer? Try installing them (https://motorola-global-portal.custhelp.com/app/answers/detail/a_id/88481) and then plugging it in. If it works, you can use Matt's Utility (http://forum.xda-developers.com/showthread.php?t=2192467) to restore to stock.
life isgood said:
I'm not sure if this will fix your problem, but do you have the proper drivers installed on your computer? Try installing them (https://motorola-global-portal.custhelp.com/app/answers/detail/a_id/88481) and then plugging it in. If it works, you can use Matt's Utility (http://forum.xda-developers.com/showthread.php?t=2192467) to restore to stock.
Click to expand...
Click to collapse
thanks man, but already tried installing all the drives, but not forward ... already many tests, including other computers but I can not that my phone is recognized by usb. I think it is hardware problem from my phone ... I found the little that has not as installing a nandroid recovery by native, so if I do not get the computer to recognize my phone, there is no hope for me.
The only thing I can think of would be to try out one of these http://shop.teamblackhat.info/Factory-style-programming-cable-for-Motorola-FactCable.htm and hope the computer recognizes it. Anybody else know if this would work if the computer doesn't recognize the phone at the moment?
My razr was freezing and had no usb connectivity at all... factory cable was the solution. Ordered mine on e-bay. :good:
jacobs7th said:
My razr was freezing and had no usb connectivity at all... factory cable was the solution. Ordered mine on e-bay. :good:
Click to expand...
Click to collapse
I sent my phone for technical assistance .. any news I notice everyone
Get a factory cable flash fastboot files. Through rsd lite and your good to go
Sent from my Optimus G using Tapatalk 4 Beta
naifs_br10 said:
Get a factory cable flash fastboot files. Through rsd lite and your good to go
Sent from my Optimus G using Tapatalk 4 Beta
Click to expand...
Click to collapse
Agreed. Factory cable and RSD unbricked my phone and all I had left was bootloader. I'd flashed an ICS recovery on JB and even killed the android recovery.
Sent from my XT912 using xda app-developers app
Guys, I was trying to flash a CM11 ROM with Safestrap and it got crazy saying my internal storage was only 1.6GB, I was kinda desperate and wiped the internal storage but after that the phone won't start, fastboot, nothing. When its connected to the charger it gets stuck at the motorola logo and connected with usb it lights up the front led. but nothing happens.
Can someone help me flashing the rom again back to my Razr? Can be the stock ROM.
marcelo.arakaki said:
Guys, I was trying to flash a CM11 ROM with Safestrap and it got crazy saying my internal storage was only 1.6GB, I was kinda desperate and wiped the internal storage but after that the phone won't start, fastboot, nothing. When its connected to the charger it gets stuck at the motorola logo and connected with usb it lights up the front led. but nothing happens.
Can someone help me flashing the rom again back to my Razr? Can be the stock ROM.
Click to expand...
Click to collapse
If you have an XT912, you can use Matt's Utility.
For XT910, use RSDLite to flash your stock ROM.
Lok for those in dev and general section.
neo.ank said:
If you have an XT912, you can use Matt's Utility.
For XT910, use RSDLite to flash your stock ROM.
Lok for those in dev and general section.
Click to expand...
Click to collapse
Thanks for the reply, but RSD does not find my phone (XT910), it won't boot on fastboot.
marcelo.arakaki said:
Thanks for the reply, but RSD does not find my phone (XT910), it won't boot on fastboot.
Click to expand...
Click to collapse
Well, some had luck to RSD even when fastboot was not available.
You should re-install the drivers. Also, there's a chance your battery is out of power.You'll need a factory cable in that case.
neo.ank said:
Well, some had luck to RSD even when fastboot was not available.
You should re-install the drivers. Also, there's a chance your battery is out of power.You'll need a factory cable in that case.
Click to expand...
Click to collapse
Yes man, now I believe my battery is dead, I'll try the factory cable later and post the results.
Thanks for the help
marcelo.arakaki said:
Yes man, now I believe my battery is dead, I'll try the factory cable later and post the results.
Thanks for the help
Click to expand...
Click to collapse
I know I'm really late but you don't need a factory cable if your phone battery is dead. You can cut off the tip of your cell phone charger's Micro-USB and attach the appropriate wires to the battery terminals inside the phone. I've done this before. I was in Safestrap and wiped my phone's Stock ROM. I bricked my phone and had battery life under 10% so Matt's Droid Utility wouldn't work. There is a video on YouTube showing how to do it. A factory cable is preferable to the method I used because you'll need a new charger obviously.