Hi all,
I have a Samsung Galaxy S3 with a default ROM, rooted and with clockworkmod installed.
Yesterday night I let it charging and working fine. This morning was freezed on the startup screen, the one that says "Samsung Galaxy SIII GT-I93000" and was not possible to go over it. I checked for similar posts in the forum but no one had the same characteristics, all could go further the starting screen.
I tried the next:
- Normal restart: Nothing, same screen
- Take out the battery: Nothing, same screen
- Try to enter in recovery mode (power+home+vol up): Nothing, same screen
- Try to enter in download mode (power+home+vol down): Success, i'm download mode.
What can I do now? there is any chance to enter without re-installing rom and wiping the whole content?
Please, any help is welcome. I'm without mobile meanwhile
Thank you in advance
If the phone does not start in normal mode and recovery mode but it starts in download mode, try to flash a rom Samsung not wipe, if it fails to start still not done with the full wipe rom SAMSUNG
AndroidGaalaxy said:
If the phone does not start in normal mode and recovery mode but it starts in download mode, try to flash a rom Samsung not wipe, if it fails to start still not done with the full wipe rom SAMSUNG
Click to expand...
Click to collapse
Hi, thank you for the fast answer.
I just found the original stock image that i had:
Country/Carrier: Poland (Play)
Date:2012 July
Android: 4.0.4
PDA:I9300XXBLFB
CSC:I9300PRTBLG1
I will turn the phone in download mode and I will connect with Odin.
Sorry about the newbie question: How I flash a new ROM on the phone without wiping all?
Best Regards
Hi,
I try to install flash again the stock ROM and I got this message in Odin.
Code:
<ID:0/007> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9300XXBLFB_I9300PRTBLG1_I9300XXLFB_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/007> Odin v.3 engine (ID:7)..
<ID:0/007> File analysis..
<ID:0/007> SetupConnection..
<ID:0/007> Initialzation..
<ID:0/007> Get PIT for mapping..
<ID:0/007>
<ID:0/007> There is no PIT partition.
<ID:0/007> Added!!
<OSM> All threads completed. (succeed 0 / failed 1)
I found another post with the same problem: http://forum.xda-developers.com/showpost.php?p=30060308&postcount=23
I tried to restore a PIT file but is failing the whole time
At the end the user told that he brought it to a Samsung service and they changed the "charging regulator" and now the phone is working. :http://forum.xda-developers.com/showpost.php?p=31105754&postcount=34
I don't have any service shop here were I live
Any other idea that I could try?
Thank you in advance
lastminuteproject said:
Hi,
I try to install flash again the stock ROM and I got this message in Odin.
Code:
<ID:0/007> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9300XXBLFB_I9300PRTBLG1_I9300XXLFB_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/007> Odin v.3 engine (ID:7)..
<ID:0/007> File analysis..
<ID:0/007> SetupConnection..
<ID:0/007> Initialzation..
<ID:0/007> Get PIT for mapping..
<ID:0/007>
<ID:0/007> There is no PIT partition.
<ID:0/007> Added!!
<OSM> All threads completed. (succeed 0 / failed 1)
I'm totally lost now.
any idea?
Thank you in advance
Click to expand...
Click to collapse
Firm Odin, unplugged the USB cable
Open Odin again Selects the file
restart again the phone to download
replug USB cable and try again
And if it still does not try to flash a recovery and tried to boot into recovery mode
lastminuteproject said:
Hi,
I try to install flash again the stock ROM and I got this message in Odin.
Code:
<ID:0/007> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9300XXBLFB_I9300PRTBLG1_I9300XXLFB_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/007> Odin v.3 engine (ID:7)..
<ID:0/007> File analysis..
<ID:0/007> SetupConnection..
<ID:0/007> Initialzation..
<ID:0/007> Get PIT for mapping..
<ID:0/007>
<ID:0/007> There is no PIT partition.
<ID:0/007> Added!!
<OSM> All threads completed. (succeed 0 / failed 1)
I'm totally lost now.
any idea?
Thank you in advance
Click to expand...
Click to collapse
Did you try to install a .pit file?
RoelVB said:
Did you try to install a .pit file?
Click to expand...
Click to collapse
This is what causes problem apparently...
Hi
I tried several different PIT files and I always get the same message in Odin:
Code:
<ID:0/007> Added!!
<ID:0/007> Odin v.3 engine (ID:7)..
<ID:0/007> File analysis..
<ID:0/007> SetupConnection..
<ID:0/007> Initialzation..
<ID:0/007> Set PIT file..
<ID:0/007> DO NOT TURN OFF TARGET!!
<ID:0/007>
<ID:0/007> Re-Partition operation failed.
<ID:0/007> Added!!
<OSM> All threads completed. (succeed 0 / failed 1)
@AndroidGaalaxy: I can't enter in recovery mode, just in download mode
I don't know what else to try, please help, some other ideas?
lastminuteproject said:
Hi
I tried several different PIT files and I always get the same message in Odin:
Code:
<ID:0/007> Added!!
<ID:0/007> Odin v.3 engine (ID:7)..
<ID:0/007> File analysis..
<ID:0/007> SetupConnection..
<ID:0/007> Initialzation..
<ID:0/007> Set PIT file..
<ID:0/007> DO NOT TURN OFF TARGET!!
<ID:0/007>
<ID:0/007> Re-Partition operation failed.
<ID:0/007> Added!!
<OSM> All threads completed. (succeed 0 / failed 1)
@AndroidGaalaxy: I can't enter in recovery mode, just in download mode
I don't know what else to try, please help, some other ideas?
Click to expand...
Click to collapse
Try to flash a ROM Samsung Jelly Bean (They Do Requires PDA only normally) and do not put anything in pit
Personally I no longer believe too
Yeah Im having the same problem...
apparently the chip that stores boot got non-functional data or something...missed-up in other words
anyhow...from several threads I looked up,,,,only 2 things can solve this , either Jtag repair the phone (check google) or service the phone, but if the flash counter shows in download mode they might not do it on warranty...
my phone has been in service for 3 days now, still didn't tell me if they'll service on warranty or not, luckily I used triangle reset before, everything shows as official samsung except custom rom.
Thank you for the replies.
Regarding bringing it to the service, I have another small issue. I got my mobile in PL. A friend wanted an internet contract there and with that contract the phone was really cheap, so I pay the phone and he kept the SIM....and I live in Germany
I will try to bring it to any shop, let's see what they tell me.
Another question now: I had an original stock ROM, but I just root it to be able to make full backups. They can realize about this entering just in download mode? Is normal that I see "Odin Mode" when I enter in download mode?
Thank you all
lastminuteproject said:
Thank you for the replies.
Regarding bringing it to the service, I have another small issue. I got my mobile in PL. A friend wanted an internet contract there and with that contract the phone was really cheap, so I pay the phone and he kept the SIM....and I live in Germany
I will try to bring it to any shop, let's see what they tell me.
Another question now: I had an original stock ROM, but I just root it to be able to make full backups. They can realize about this entering just in download mode? Is normal that I see "Odin Mode" when I enter in download mode?
Thank you all
Click to expand...
Click to collapse
Download mode is already integrated in the smartphone by cons they may know that you have changed the phone because this flash counter in download mode they would have had to turn away a triangle reset the counter but hey it is not possible because you can not start the phone
Download Mode
AndroidGaalaxy said:
Download mode is already integrated in the smartphone by cons they may know that you have changed the phone because this flash counter in download mode they would have had to turn away a triangle reset the counter but hey it is not possible because you can not start the phone
Click to expand...
Click to collapse
In my situation, my S3 is in download mode but the computer can not see it through a com (up-to-date Odin and Kies can not see my GS3). What should I do?
Messing with PIT maybee ruined your phone.
If it s in warranty maybee they flash it for you. I´ve experienced that before with no problems but I know that it voyds the warranty flashing PIT and rooting.
Maybee you re lucky in the samsung service, in your position I was that way. Jtag is very risky and voyds warranty forever. If you pay in samsung for the boot repair you continue to have your warranty again and for the price of a Jtag intervention I would pay a bit more and continue having warranty.
S3 frozen on boot screen while rooting
Hello everyone,
I'm new around here and i apologize if posting in the wrong place....
I have a similar problem: I decided to root my S3 (UK unlocked) and followed one of many tutorials on YouTube (made by galaxys3root). Everything seemed to be easy and started well until at the point when the S3 must reboot. At that point the phone got stuck, and the only thing i can do is to go in downloading mode.
Odin gives me this
<ID:0/003> Added!!
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> recovery.img
<ID:0/003> NAND Write Start!!
<ID:0/003> cache.img
<ID:0/003> param.bin
<ID:0/003> RQT_CLOSE !!
<ID:0/003> RES OK !!
<ID:0/003> Completed..
<ID:0/003> Added!!
<OSM> All threads completed. (succeed 1 / failed 0)
<ID:0/003> Removed!!
While the phone is stuck on the boot screen my PC (Win 7 Ultimate) does not recognize the device, while if the phone is in downloading mode, the PC has the driver for it.
I went through a few more topics on this forum which described something similar, tried a few of the suggestions made by others but nothing seems to work.
Does anyone has a solution for this or I should take the phone in service?
I would appreciate any advise!
I'm quite the beginner so if you could use a technical "friendly" language it would be great
Related
I made the mistake of trading phones with a guy whose GS4 was rooted with SS recovery and there were no MSD in it when we traded. I brought it home, restarted it. And it began to get stuck on the "FIRMWARE UPGRADE ENCOUNTERED AN ISSUE. PLEASE SELECT RECOVERY MODE IN KIES & TRY AGAIN." which I know to not use Kies as it was useless to me when I had my first GS4 at time of launch. I am fairly new at this with a gs4. I have tried and tried with ODIN v3.07. I have been on here and looking through forums and I went to other forums besides xda with countless different trials. NONE have been even the slightest bit helpful...
I was wondering since it was stuck on the devilish yellow triangle screen. I can not even get past this to get the launcher... could ADB be the problem since I can't get it to even boot up to enable it?
before anyone asks, to which will waste both our time....
yes, i have used the stock vz firmware and placed it in the PDA section in ODIN
THIS IS WHAT I GET EVERY TIME.
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I545VRUAME7_I545VZWAME7_I545VRUAME7_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> sbl2.mbn
<ID:0/003> NAND Write Start!!
<ID:0/003> sbl3.mbn
<ID:0/003> rpm.mbn
<ID:0/003> aboot.mbn
<ID:0/003> FAIL! (Auth)
<OSM> All threads completed. (succeed 0 / failed 1)
ALL HELP IS MUCH APPRECIATED!!:good:
Are you sure you were on ME7? You might need to flash a newer firmware.
Sent from my NCC-1701 using Tapatalk.
Definitely need to flash newer firmware
degradedtree69 said:
I made the mistake of trading phones with a guy whose GS4 was rooted with SS recovery and there were no MSD in it when we traded. I brought it home, restarted it. And it began to get stuck on the "FIRMWARE UPGRADE ENCOUNTERED AN ISSUE. PLEASE SELECT RECOVERY MODE IN KIES & TRY AGAIN." which I know to not use Kies as it was useless to me when I had my first GS4 at time of launch. I am fairly new at this with a gs4. I have tried and tried with ODIN v3.07. I have been on here and looking through forums and I went to other forums besides xda with countless different trials. NONE have been even the slightest bit helpful...
I was wondering since it was stuck on the devilish yellow triangle screen. I can not even get past this to get the launcher... could ADB be the problem since I can't get it to even boot up to enable it?
before anyone asks, to which will waste both our time....
yes, i have used the stock vz firmware and placed it in the PDA section in ODIN
THIS IS WHAT I GET EVERY TIME.
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I545VRUAME7_I545VZWAME7_I545VRUAME7_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> sbl2.mbn
<ID:0/003> NAND Write Start!!
<ID:0/003> sbl3.mbn
<ID:0/003> rpm.mbn
<ID:0/003> aboot.mbn
<ID:0/003> FAIL! (Auth)
<OSM> All threads completed. (succeed 0 / failed 1)
ALL HELP IS MUCH APPRECIATED!!:good:
Click to expand...
Click to collapse
This has happened to me about four times with my phone. I was able to fix through a process of Kies and Odin. It seems that if you do all that you can in Kies, as far as attempting to re-install the stock firmware. Kies has the drivers you need in order for Odin to work. You will need to run through the Kies process (it will fail), but you will get the drivers you need. You will then need to boot into download mode and do the Odin flash process. This is all assuming you have the correct files for Odin. You will need to flash the stock build afterwards unless you have a backup and are able to access safestrap which i doubt you will have.
Hi, I have a Samsung Galaxy S3 (GT-i9300) which was working fine until the other day. The phone was plugged into the charger and immediately restarted itself and stuck at the initial loading screen. I could boot into TWRP recovery but was unable to mount any partitions and if I tried a factory reset it reported that there was no OS installed on the phone.
So I decided to reload the factory firmware using Odin. I have downloaded what I beleive to be the correct factory 4.3 firmware (I9300XXUGMK6_I9300OXAGMK6_BTU.zip) but when I try to load it using Odin it fails at around 90% (see screenshot).
The complete message log is as follows:
Code:
<ID:0/007> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9300XXUGMK6_I9300OXAGMK6_I9300XXUGMK6_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/007> Odin v.3 engine (ID:7)..
<ID:0/007> File analysis..
<ID:0/007> SetupConnection..
<ID:0/007> Initialzation..
<ID:0/007> Get PIT for mapping..
<ID:0/007> Firmware update start..
<ID:0/007> SingleDownload.
<ID:0/007> sboot.bin
<ID:0/007> NAND Write Start!!
<ID:0/007> tz.img
<ID:0/007> boot.img
<ID:0/007> recovery.img
<ID:0/007> system.img
<ID:0/007> modem.bin
<ID:0/007> cache.img
<ID:0/007> hidden.img
<ID:0/007> FAIL!
<ID:0/007>
<ID:0/007> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Here is a screenshot of Odin when it fails. One concern I have is that at the top of the screen it sdays 'Odin3 i9505'. Should that not say the model of the connected phone which in my case would be i9300
If anyone could offer some advice I would be gratefull.
Thanks
EDIT: I forgot to mention, since the failed attempt I can no longer boot into recovery but I can still boot into download mode.
Try the rescue firmware with pit, search in general forum.
boomboomer said:
Try the rescue firmware with pit, search in general forum.
Click to expand...
Click to collapse
Thanks for that boomboomer, I'm downloading it now.
What do you think about Odin not displaying my phone model at the top of the screen. Is this something I should be worried about or just ignore it for the moment.
My the same , but select rom forr I9305 bot i9300 and it fail on modem
and i flash i9300 rom and it works perfect
Hi there,
it's matteios1984 first of all i'd like to say hello to the comunity and thank you all for interesting post about Android!
I'm here to asking help about a tricky case. I've a Samsung Galaxy S3 (i9300) bricked. In other words the phone behaves as follow:
- If i try to turn on the device it remains stuck on Samsung S3 logo
- No possible to boot in recovery mode
- When I connect it to the charger it's stucked showing the battery image and not showing any progress about charging status
- The device is still able to boot in download mode both with buttons combo and with resistor trick, but Odin is not able to flash anything on the device (my idea is to flash a Customer Recovery, perform a full wipe of the device and after restore original italian firmware)
Here following a log taken from Odin:
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> recovery.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003>
<ID:0/003> There is no PIT partition.
<OSM> All threads completed. (succeed 0 / failed 1)
Click to expand...
Click to collapse
If i try to flash a file containing PIT informations here following the log from Odin:
<ID:0/003> Added!!
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Set PIT file..
<ID:0/003> DO NOT TURN OFF TARGET!!
<ID:0/003> Get PIT for mapping..
<ID:0/003> There is no PIT partition.
<OSM> All threads completed. (succeed 0 / failed 1)
Click to expand...
Click to collapse
I've heard about the possibility to boot the device by a MicroSD card that allows me to flash the device... Do you think this will fix my issue? Or do I need a box? If so, any suggestion about the model is appreciated.
Thanks in advance for your support
Try downgrading the bootloader to BLFB before flashing firmware or pit.
Hello,
i try to install twrp on my s6 edge, but now it will not start anymore, the screen is following the samsung Logo black.
i try to install the original firmware from sammobile, but it stuck or give me an error.
what can i do? i try on 2 computer, 2 usb cable and and and... its the same all time
can you help me pls?
<ID:0/006> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> G925FXXU1AOCV_G925FAUT1AOCN_G925FXXU1AOCW_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/006> Odin v.3 engine (ID:6)..
<ID:0/006> File analysis..
<ID:0/006> SetupConnection..
<ID:0/006> Initialzation..
<ID:0/006> Get PIT for mapping..
<ID:0/006> Firmware update start..
<ID:0/006> sboot.bin
<ID:0/006> NAND Write Start!!
<ID:0/006> Complete(Write) operation failed.
<ID:0/006> Added!!
<OSM> All threads completed. (succeed 0 / failed 1)
Click to expand...
Click to collapse
sure you using latest Odin..? and firmware matches..?
try from odin 1.85 to 3.10 all
What model of s6 edge you haw??Look on samifirmware for yours model.Use odin 3.10.6 i think
and use the right region code BTW branding code..for free Germany it's dbt as example..
I hate to say it, but I have the exact same issue...
I tried to install TWRP, now the screen just goes blank after the Samsung logo.
I have downloaded the latest O2 UK firmware, flashed as normal using odin 3.10.6, and I get a "fail" too
Please could someone suggest something?
Thanks
EDIT: Re-flashed root, and all good again!
Guys i was upgrading official firmware through ODIN, but it failed. Tried flashing TWRP Recovery as well and below error occured. Need help as my S6 Edge 925F is stuck and won't boot. One more thing, i can enter download mode just fine.
<ID:0/003> Added!!
<ID:0/003> Odin engine v(ID:3.1005)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003>
<ID:0/003> Get PIT for mapping..
<ID:0/003> There is no PIT partition.
<OSM> All threads completed. (succeed 0 / failed 1)
PIT related error bothers me .......
@aneeqkhan I know this thread is a bit dated now, but nobody has replied to you question either? I am trying to recover my friends Galaxy S6 Edge SM-G925I, his bricked after a failed standard OTA update. Flashing stock firmware worked for about 1 week then the whole thing crashed and is un-bootable. Attempting to flash the exact same firmware again in hopes that I could boot into recovery (recovery by button combination DOES NOT WORK!) so was hoping to just boot and factory reset (I was thinking that maybe a data corruption was the cause we didn't wipe his phone because he didn't back it up)...upon putting the device into download mode and flashing the exact same firmware package that worked the week before I get the same error that you are getting? Not only that but none of the claimed fixes online for these devices has worked!?
Note: This is a 100% stock device never had anything flashed to it before I got it and still hasn't had anything custom flashed to it either
I am more interested now if you managed to recover your S6 and if so how did you do it?
Pretty sure i bricked this to no repair.
So got my Sprint s6 edge few months ago and rooted it a week after. Sadly i dont know what i used rom wise to root it since its been a month+. Sadly i reformated pc awhile back so can't see the files i used.
Got bored and wanted to try and install xposed to add some new features to my phone. So just tried and i'm prety sure i bricked it hard...
what i followed
gs6.wonderhowto.com/how-to/install-xposed-framework-your-samsung-galaxy-s6-s6-edge-0163918/
It said make a recovery so i did by following
gs6.wonderhowto.com/how-to/install-custom-recovery-your-galaxy-s6-s6-edge-0161619/
I did what he did and after it asked for a reboot i rebooted and it got stuck on samsung boot logo saying "Recovery not SEANDROID Enforcing" in top left corner.
So i googled how to remove root and how to get past this screen and many suggested stock rom. I tried that and odin (v3.09) wont get past "Write NAND!"
I let it set for 20 minutes and nothing happened so i googled and everyone claimed trying different usb hubs and cables so i did that. I've tried every usb hub on my pc(8) and all 3 cables i had. So then tried different version v3.10.7 of odin and it fails with following
<OSM> Enter CS for MD5..
<OSM> Binary Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Added!!
<ID:0/005> Odin engine v(ID:3.1100)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> SingleDownload.
<ID:0/005> sboot.bin
<ID:0/005> NAND Write Start!!
<ID:0/005> FAIL!
<ID:0/005>
<ID:0/005> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
And in top right under Odin mode it reads
Product Name: SM-G295P
Current binary: Custom
System Status: Custom
FRP Lock: OFF
Secure Download: Enabled
Knox warranty void: 1 (0x0301)
RP SWREV: B:3 K:2 S:2
SW REV. CHECK FAIL. DEVICE: 3, BINARY: 1
So now i'm just lost and scared at what to do. I googled "SW REV. CHECK FAIL. DEVICE: 3, BINARY: 1" And my findings are just to use stock rom...but thats what i did in first place. So now i'm stuck with a phone that is continuously rebooting itself to the samsung boot logo....
G925PVPU1AOCF_G925PSPT1AOCF_G925PVPU1AOCF_HOME.tar.md5 is the rom im trying to flash with and i believe it is stock because got it off this forum from a post claiming it was the new stock updated rom.
Can someone please help? I can skype or teamspeak or ventrilo or just use this forum to help me but i'm beyond confused on what to do now...
edit- phone is continuously rebooting itself to the samsung boot logo...but i managed to make it stop by making phone sit in download mode...
edit2- i can not go into recovery or safe mode. All i can do is wtach my phone go to the boot logo "Samsung Galaxy S6 Edge" screen then to black screen back to boot screen. And i can put it into download mode.... Thats it...The brick is real...
edit 3- 40 views and not one help lol, seems i'll be craigslist shopping soon.
You tripped the Knox counter, that is for sure. Since you can enter download mode that means it is still possible to install the stock firmware. Did you use the correct firmware for your model?
Snowby123 said:
You tripped the Knox counter, that is for sure. Since you can enter download mode that means it is still possible to install the stock firmware. Did you use the correct firmware for your model?
Click to expand...
Click to collapse
I'm pretty sure
SPR-G925PVPU1AOCF-20150415164450
forum.xda-developers.com/sprint-galaxy-s6-edge/general/sm-g925p-firmware-available-t3084414
Is the stock rom i used to try and fix that recovery screwup.
i tried G925PVPU3BOJ7_G925PSPT3BOJ7_G925PVPU3BOJ7_HOME.tar which is a 5.1.1 stock rom and still same results!!!
Try performing a log cat. That is a low skill technique of diagnosing problems in android during a boot loop.
Snowby123 said:
Try performing a log cat. That is a low skill technique of diagnosing problems in android during a boot loop.
Click to expand...
Click to collapse
I dont know how or what a log cat is.
Edit- just turned device back on and plugged itno computer and now blue screen saying An error occured while updating the device software. use emergency function in the smart switch pc software. Yet the smart switch software says unsupported device.
randomly got it to work after 2 hours of leaving it alone i can now start to install the stock firmware but it stops
<ID:0/007> Added!!
<OSM> Enter CS for MD5..
<OSM> Binary Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/007> Odin engine v(ID:3.1100)..
<ID:0/007> File analysis..
<ID:0/007> SetupConnection..
<ID:0/007> Initialzation..
<ID:0/007> Get PIT for mapping..
<ID:0/007> Firmware update start..
<ID:0/007> SingleDownload.
<ID:0/007> sboot.bin
<ID:0/007> NAND Write Start!!
<ID:0/007> cm.bin
<ID:0/007> boot.img
<ID:0/007> recovery.img
<ID:0/007> system.img
<ID:0/007>
<ID:0/007> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/007> Removed!!
i dk if phone not charged enough or what
edit---
It fails on same part, but progress bar is sometimes farther. Tried it 3 times in total, just going to put phone on charger(wall outlet) for a few hours then try again
also sorry for double posting...