Hi all,
My GS3 (International version) is on a constant boot loop. I was browsing the internet and then it crashed into a loop, The phone was getting on my nerves abit as i was constantly having to reboot just to use it...but this time it crashed on me for good (Yes it was rooted on firmware 4.1.1)
I managed to get into CWM and wipe all data, then get into Download mode and flash a stock rom via ODIN.
All seemed to be going well, ODIN said PASSED and the phone rebooted.
Then i got the little green android robot with the blue spinning box in the middle of him/her....Boots back to initial start up screen, then little green android, then intitial start up etc etc etc....Never leaves these screens.
I cannot enter recovery nor can i enter download mode. There is nothing i can do to stop this.
I have tried repeatadly taking out the battery and puttin back in but no results.
Any tips?
Thanks in advance
From a very stressed out GS3 owner
After much playing around i managed to get back into DOWNLOAD mode...Unfortunatly no matter which STOCK rom i put on i can never get past the initial loading screen where it states my Phone device name/brand etc. Someimes i get to the little android with the spinning blue square in its belly...But then it loops again.
Ive tried about 6 different fimwares now, all stock.
Ive managed to put CWN on them too and done the whole WIPE DATA/DELVIK cache...but nothing changes!
Help please
I am in a right pickle now, Any help would be really really really appreciated. Feel gutted!
Tried everything i can think of or find, but my problems are just getting worse. I can now no longer use ODIN as i get the following:
<ID:0/005> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9300XXALF2_I9300ODDALF1_I9300DDLEA_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Odin v.3 engine (ID:5)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005>
<ID:0/005> There is no PIT partition.
<ID:0/005> Added!!
<OSM> All threads completed. (succeed 0 / failed 1)
The firmware i was trying to flash is suppose to be the ORIGINAL S3 firmware.
On the DOWNLOAD MODE screen on the S3, next to product name i have nothing.. Used to say GT-I9300
Custom Binary: No
Current Binary: Samsung Official
System Status: Custom
I can get into DOWNLOAD MODE but cannot access Recovery.
What to do now?
The phone is 4 months old :crying::crying::crying::crying:
ToonTonic said:
I am in a right pickle now, Any help would be really really really appreciated. Feel gutted!
Tried everything i can think of or find, but my problems are just getting worse. I can now no longer use ODIN as i get the following:
<ID:0/005> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9300XXALF2_I9300ODDALF1_I9300DDLEA_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Odin v.3 engine (ID:5)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005>
<ID:0/005> There is no PIT partition.
<ID:0/005> Added!!
<OSM> All threads completed. (succeed 0 / failed 1)
The firmware i was trying to flash is suppose to be the ORIGINAL S3 firmware.
On the DOWNLOAD MODE screen on the S3, next to product name i have nothing.. Used to say GT-I9300
Custom Binary: No
Current Binary: Samsung Official
System Status: Custom
I can get into DOWNLOAD MODE but cannot access Recovery.
What to do now?
The phone is 4 months old :crying::crying::crying::crying:
Click to expand...
Click to collapse
Code:
<ID:0/005> There is no PIT partition.
<ID:0/005> Added!!
<OSM> All threads completed. (succeed 0 / failed 1)
This is the troublesome part..in your flashing frenzy you have somehow corrupted the partition layout...now try flashing the 3 part method..search for it..you will need to use mx.pit to repartition you flash memory..tread cautiously and do only what you understand..
Why do people use Odin??????? Still escapes me
i see a post with a bootloader a pit and a rom to repair gs III and get a phone like the first time try to flash it and see
edit = i find it http://forum.xda-developers.com/showthread.php?t=1825272
Thank you for your replies, I am still stuck but am currently downloaded the emergency firmware that kondronaute posted a link too.
Fingers crossed it works!
kondronaute said:
i see a post with a bootloader a pit and a rom to repair gs III and get a phone like the first time try to flash it and see
edit = i find it http://forum.xda-developers.com/showthread.php?t=1825272
Click to expand...
Click to collapse
Unfortunatly this didnt work for me, ODIN said FAIL
Then 2nd time around it just got stuck at SetupConnection
What is the exact model (aka "variant") of your phone? (if you don't know, you can use this app to find out)
Simonetti2011 said:
What is the exact model (aka "variant") of your phone? (if you don't know, you can use this app to find out)
Click to expand...
Click to collapse
I cant use tha app as im stuck on a boot loop, i can only access Download mode. I have a GS3 GT-I9300 International version UK. Just took it to the store i bought it at and theres nothing they can help me with other than telling me to contact samsung.
I have tried nurmerous files via ODIN, even PIT files but i get no results. ODIN just says FAIL.
When i enter DOWNLOAD mode on my GS3..prior to pressing volum up i have a small yellow triangle, but it still allows me to go on. Prior to Download mode i can only get as far as the initial boot screen.
ToonTonic said:
Unfortunatly this didnt work for me, ODIN said FAIL
Then 2nd time around it just got stuck at SetupConnection
Click to expand...
Click to collapse
sorry send it back to samsung
i see another post for repair that but need a Jtag ... not for simple user... :crying:
ToonTonic said:
I cant use tha app as im stuck on a boot loop, i can only access Download mode. I have a GS3 GT-I9300 International version UK. Just took it to the store i bought it at and theres nothing they can help me with other than telling me to contact samsung.
OK what ssn is listed under the battery .
Its pointless proceeding until the model is confirmed as your symptoms are identical to flashing wrong firmware .
I have tried nurmerous files via ODIN, even PIT files but i get no results. ODIN just says FAIL.
Possible corrupt NAND then .
jje
Click to expand...
Click to collapse
JJEgan said:
ToonTonic said:
I cant use tha app as im stuck on a boot loop, i can only access Download mode. I have a GS3 GT-I9300 International version UK. Just took it to the store i bought it at and theres nothing they can help me with other than telling me to contact samsung.
OK what ssn is listed under the battery .
Its pointless proceeding until the model is confirmed as your symptoms are identical to flashing wrong firmware .
I have tried nurmerous files via ODIN, even PIT files but i get no results. ODIN just says FAIL.
Possible corrupt NAND then .
jje
Click to expand...
Click to collapse
SSN: I9300GSMH
Whats the number to samsung lol
Click to expand...
Click to collapse
I have spoken with Samsung who have sent me out a jiffy bag to send back to them with my phone and they will fix under warranty. Im at my wits end with it. So in the mean time im back my iPhone (errrgghh i hate it).
Out of interest is there anything i need to do to the phone prior to sending it back?
On the download scren (after pressing Volume Down + Home + Power) prior to pressing volume up i have a small yellow triangle on the bootom of that screen, is this normal??
When pressing Volume Up it goes into ODIN mode with the big green android robot..Text underneath says DOWNLOADING...I know this is right.
Top left of screen looks as follows:
ODIN MODE
Product Name:
Custom Binary Download: No
Current Binary: Samsung Official
System Status: Custom
Anything i should try and fix? Not that i can lol
zoot1 said:
Code:
<ID:0/005> There is no PIT partition.
<ID:0/005> Added!!
<OSM> All threads completed. (succeed 0 / failed 1)
Click to expand...
Click to collapse
I met the similar message it it is very bad.
Most likely died MMC.
You can try to flash PIT file but it seems to me its partition is dead, however as well as all remaining partitions. Now only motherboard changeover
as i9000 said:
I met the similar message it it is very bad.
Most likely died MMC.
You can try to flash PIT file but it seems to me its partition is dead, however as well as all remaining partitions. Now only motherboard changeover
Click to expand...
Click to collapse
ToonTonic said:
I have spoken with Samsung who have sent me out a jiffy bag to send back to them with my phone and they will fix under warranty. Im at my wits end with it. So in the mean time im back my iPhone (errrgghh i hate it).
Out of interest is there anything i need to do to the phone prior to sending it back?
On the download scren (after pressing Volume Down + Home + Power) prior to pressing volume up i have a small yellow triangle on the bootom of that screen, is this normal??
When pressing Volume Up it goes into ODIN mode with the big green android robot..Text underneath says DOWNLOADING...I know this is right.
Top left of screen looks as follows:
ODIN MODE
Product Name:
Custom Binary Download: No
Current Binary: Samsung Official
System Status: Custom
Anything i should try and fix? Not that i can lol
Click to expand...
Click to collapse
Any answers to this?
Yeh its pretty messy
ToonTonic said:
Any answers to this?
Yeh its pretty messy
Click to expand...
Click to collapse
All the actions are meaningless and do not lead to nothing...
Stuck in bootloop, help please!
ToonTonic said:
Hi all,
My GS3 (International version) is on a constant boot loop. I was browsing the internet and then it crashed into a loop, The phone was getting on my nerves abit as i was constantly having to reboot just to use it...but this time it crashed on me for good (Yes it was rooted on firmware 4.1.1)
I managed to get into CWM and wipe all data, then get into Download mode and flash a stock rom via ODIN.
All seemed to be going well, ODIN said PASSED and the phone rebooted.
Then i got the little green android robot with the blue spinning box in the middle of him/her....Boots back to initial start up screen, then little green android, then intitial start up etc etc etc....Never leaves these screens.
I cannot enter recovery nor can i enter download mode. There is nothing i can do to stop this.
I have tried repeatadly taking out the battery and puttin back in but no results.
Any tips?
Thanks in advance
From a very stressed out GS3 owner
Click to expand...
Click to collapse
Hi, did you manage to get yours solved?
I have the exact same problem i was on a custom samsung 4.1.2 rom and while browsing the net it crashed was in bootloop now i cant get out, went into recovery mode and factory reseted didnt help, now i cant go back into clockwork mod at all, so i went into download mode and opened odin flashed a stock rom just keeps saying fail after nand write, tried a custom rom and same issue and fails, now when i pull the battery out and turn it back on all i get is a message saying firmware upgrade encountered an issue please select recovery mode in kies and try again! Helppppp!
Thankss
Contact Samsung, or seller, will need to be repaired under warranty.
In all that did you even try using kies to get back to original rom?
Even if it's rooted? Thanks
Sent from my Nexus 4 using xda app-developers app
Related
Hello
My GS3 suddenly restarted and stuck on galaxy s 3 logo
I cant go to stock recovery by pressing (Vol+ Menu Power)
I only can go to download mode
My galaxy version is Norway Telenor operator
I find the suitable rom for my GT-19300 and its TEN-I9300XXEME2-20130522163915.zip
I try to flashed it with odin but I get this error
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9300XXEME2_I9300TENEME2_I9300XXEMB6_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/008> Odin v.3 engine (ID:8)..
<ID:0/008> File analysis..
<ID:0/008> SetupConnection..
<ID:0/008> Initialzation..
<ID:0/008> Get PIT for mapping..
<ID:0/008>
<ID:0/008> There is no PIT partition.
<ID:0/008> Added!!
<OSM> All threads completed. (succeed 0 / failed 1)
Click to expand...
Click to collapse
I also try all other way like fixing bootloder ( flashing VRALEC.bootchain.tar.md5 & BOOTLOADER_I535VRALF2_618049_REV09_user_low_ship.tar.md5 & stock.vzw_root66.7z )
But I receive above error for them
Is there any body can help me
I stock in this sh...ty situation for like a week
If you need any screen shot or any thing I'll be here
what is this for god sake <ID:0/008> There is no PIT partition
My problem is that My GT is not international and its norway telenor and I unlocked it by ez unlocker and it worked fine for like a year
PLZ Help
By the way I tried all pit for 16 gig pit now and checked repartition but its not worked
I think this guy in this threat(http://forum.xda-developers.com/showthread.php?t=2098007) have exact my problem and people their said that his phone is dead
I'am Very Hopeless plz help
No solution yet...
I've tried flashing with 5 files, 4 files, 3 files only nothing. diferents ports, different ODIN, nothing
aminclick68 said:
flashing VRALEC.bootchain.tar.md5 & BOOTLOADER_I535VRALF2_618049_REV09_user_low_ship.tar.md5 & stock.vzw_root66.7z
Click to expand...
Click to collapse
These are all verizon phone files so if you hadn't broken your phone already, these would have broken it...
aminclick68 said:
My problem is that My GT is not international and its norway telenor
Click to expand...
Click to collapse
You say you dont have international version, but if you're in norway you will have.
Please type everything it says on download mode screen (on phone) here.
Please dont bump threads before 24 hours.
rootSU said:
These are all verizon phone files so if you hadn't broken your phone already, these would have broken it...
You say you dont have international version, but if you're in norway you will have.
Please type everything it says on download mode screen (on phone) here.
Please dont bump threads before 24 hours.
Click to expand...
Click to collapse
Tnx for reply
Those file that you said cant flash on my phone because of that error(pit) that i said
So My phone is international (thats a good thing)!!!!!
My Phone Screen in download mode:
Odin Mode
Product Name:
Custom Binarydownload: NO
Current Binary: Samsung Official
System Status: Custom
aminclick68 said:
Tnx for reply
Those file that you said cant flash on my phone because of that error(pit) that i said
So My phone is international (thats a good thing)!!!!!
My Phone Screen in download mode:
Odin Mode
Product Name:
Custom Binarydownload: NO
Current Binary: Samsung Official
System Status: Custom
Click to expand...
Click to collapse
Yes, you have Half SDS, it does need to be repaired under warranty.
rootSU said:
Yes, you have Half SDS, it does need to be repaired under warranty.
Click to expand...
Click to collapse
Hi, I have exactly the same problem. I sent my phone to freesamsungrepairs and they refuse to fix my device under warranty since it has been rooted. Can they really tell that it has been rooted or do they base their assumption solely on the "custom" field in Download mode? I shipped the phone without sd card or anything that would tell them the phone is rooted. Can they still tell? Can they maybe read somehow the partially wiped emmc and find traces of superuser and such?
Thak you for your help.
Same problem
rootSU said:
Yes, you have Half SDS, it does need to be repaired under warranty.
Click to expand...
Click to collapse
Hi, I have the exact same problem, did you manage to get any solution? i bought my phone on internet, and it doesn't have any warranty, i hope you found a solution for this.
Other solutions include:
Have new internal memory fitted
Have new motherboard fitted
No other solutions
Sent from my GT-I9300 using Tapatalk 4
Hello,
Newbie here... I have followed this forum for three days trying to get my Note II Verizon to boot any ROM. I am only able to get it into Odin Download mode (never been able to get the System Restore Menu). Not sure what this device was originally flashed with but I can't get any bootrom to install.
I have tried the first steps and download the files poseted on this post http://forum.xda-developers.com/showthread.php?t=2043636 and get the folllowing failure:
<ID:0/006> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> BootloaderBaseline2.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/006> Odin v.3 engine (ID:6)..
<ID:0/006> File analysis..
<ID:0/006> SetupConnection..
<ID:0/006> Initialzation..
<ID:0/006> Set PIT file..
<ID:0/006> DO NOT TURN OFF TARGET!!
<ID:0/006> Get PIT for mapping..
<ID:0/006> Firmware update start..
<ID:0/006> boot.img
<ID:0/006> NAND Write Start!!
<ID:0/006> recovery.img
<ID:0/006> tz.img
<ID:0/006> sboot.bin
<ID:0/006> FAIL!
<OSM> All threads completed. (succeed 0 / failed 1)
Phone now gives the following message: "Firmware upgrade encountered an issue. Please select recovery mode in Kies & try again"
The only successful Rom I have partial success with is: KIES_HOME_I605VRAMC3_I605VZWAMC3_1098177_REV04_user_low_ship.tar.
Odin 3.185 will install this ROM successfully with the PIT. Not the phone will not boot and flashes the Galaxy Note II then turns off. It will only allow me to go back into Bootloader Mode but has never allowed me to get into recovery and wipe the phone. Boot Load screen shows everything stock except the "SYSTEM STATUS: Custom". Since I do not know what ROM was originally installed I am stuck on this one and insight would greatly appreciated. I have also tried other Odin versions including 3.07.
Thank you!
jvaldez33 said:
Hello,
Newbie here... I have followed this forum for three days trying to get my Note II Verizon to boot any ROM. I am only able to get it into Odin Download mode (never been able to get the System Restore Menu). Not sure what this device was originally flashed with but I can't get any bootrom to install.
I have tried the first steps and download the files poseted on this post http://forum.xda-developers.com/showthread.php?t=2043636 and get the folllowing failure:
<ID:0/006> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> BootloaderBaseline2.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/006> Odin v.3 engine (ID:6)..
<ID:0/006> File analysis..
<ID:0/006> SetupConnection..
<ID:0/006> Initialzation..
<ID:0/006> Set PIT file..
<ID:0/006> DO NOT TURN OFF TARGET!!
<ID:0/006> Get PIT for mapping..
<ID:0/006> Firmware update start..
<ID:0/006> boot.img
<ID:0/006> NAND Write Start!!
<ID:0/006> recovery.img
<ID:0/006> tz.img
<ID:0/006> sboot.bin
<ID:0/006> FAIL!
<OSM> All threads completed. (succeed 0 / failed 1)
Phone now gives the following message: "Firmware upgrade encountered an issue. Please select recovery mode in Kies & try again"
The only successful Rom I have partial success with is: KIES_HOME_I605VRAMC3_I605VZWAMC3_1098177_REV04_user_low_ship.tar.
Odin 185 will install this rom successfully with the PIT. Not the phone will not boot and flashes the Galaxy Note II then turns off. It will only allow me to go back into Bootloader Mode but has never allowed me to get into recovery and wipe the phone. Boot Load screen shows everything stock except the "SYSTEM STATUS: Custom". Since I do not know what ROM was originally installed I am stuck on this one and insight would greatly appreciated.
Thank you!
Click to expand...
Click to collapse
Think your version of Odin is too old. try this
https://docs.google.com/file/d/0BwO2K6_pgq39ejFubU43Nkprb2c/edit
See if 307 works better for you.
Note II Won't boot.
dragonstalker said:
Think your version of Odin is too old. try this
https://docs.google.com/file/d/0BwO2K6_pgq39ejFubU43Nkprb2c/edit
See if 307 works better for you.
Click to expand...
Click to collapse
Thank you for the reply. I made a typo and have tried Odin 3.185 and 3.07. Can't seem to get any of them to work. I have contacted Samsung and my phone is under warranty but would like to get the "CUSTOM" off the SYSTEM STATUS to avoid issues with the warranty.
Warranty costs if phone has been rooted
jvaldez33 said:
Thank you for the reply. I made a typo and have tried Odin 3.185 and 3.07. Can't seem to get any of them to work. I have contacted Samsung and my phone is under warranty but would like to get the "CUSTOM" off the SYSTEM STATUS to avoid issues with the warranty.
Click to expand...
Click to collapse
Hello,
Can can anyone share what the Out of Warranty costs are if the Verizon Note II is sent in with a Custom Rom and Samsung doesn't honor the warranty?
jvaldez33 said:
Hello,
Can can anyone share what the Out of Warranty costs are if the Verizon Note II is sent in with a Custom Rom and Samsung doesn't honor the warranty?
Click to expand...
Click to collapse
You will be charged the full price of the device. Just keep trying to fix the issue. There has to be something you aren't doing right. As long as you can get into the boot loader you are in okay shape. Just go back through the instructions and follow them as closely as you possibly can.
Sent from my Nexus 10 using Tapatalk 4
miketoasty said:
You will be charged the full price of the device. Just keep trying to fix the issue. There has to be something you aren't doing right. As long as you can get into the boot loader you are in okay shape. Just go back through the instructions and follow them as closely as you possibly can.
Sent from my Nexus 10 using Tapatalk 4
Click to expand...
Click to collapse
In my experience no matter how far gone you think your device is, if you can get into download mode and Odin recognizes it you are OK. I am sure there are circumstances where you can't recover even if you are in that position, but I have never heard of any. Agree with miketoasty, read the instructions carefully and then read them again. Be sure you have the correct files and a decently charged battery. And make sure your USB cable is good.
Sent from my GT-P3110 using xda app-developers app
Update on events
mikelikesbikes said:
In my experience no matter how far gone you think your device is, if you can get into download mode and Odin recognizes it you are OK. I am sure there are circumstances where you can't recover even if you are in that position, but I have never heard of any. Agree with miketoasty, read the instructions carefully and then read them again. Be sure you have the correct files and a decently charged battery. And make sure your USB cable is good.
Sent from my GT-P3110 using xda app-developers app
Click to expand...
Click to collapse
I have been in the IT business for nearly 25 years and have seen many problems resolved if you have the time and desire to put forth the efforts to investigate the problem every day with a clear head. With that being said I for some unknown ADD moment and decided I wanted to troubleshoot my sons girlfriend's Note II that was having problems. Now here I am wrestling with a problem like a drug addict looking for their "next fix". I am very stubborn and extremely capable of diagnosing hardware and software problems but this one truly has me stumped!
With this being a problem I decided to purchase another Note II off EBay to experiment with and was listed with similar problems, Red Light and wouldn't boot.. I figured for $125 the worst that could happen is I could disassemble it and part out the LCD/Digitizer and recuperate my investment. There are some problems I like researching and resolving and this is one. I personally believe the problems on both Note II's may both related to the charging board based on the information on the following post on another forum: http://forum.xda-developers.com/showthread.php?p=45678812#post45678812. I will elaborate a little more shortly.
Let's go over my three day 50 hour marathon. Here is the only download that successfully downloads but the phone will only splash the "GALAXY NOTE II" screen and turn off after a successful install. I have downloaded Odin 3.185 and 3.07 and get the same results:
sch-i605-16gb.pit
KIES_HOME_I605VRAMC3_I605VZWAMC3_1098177_REV04_user_low_ship.tar.md5
Unless the problem resides on my laptop I think I have eliminated the issue of having a good cable(s) by using official Samsung cables, NEW RocketFish cables and they all seem to work fine for viewing and transferring files via USB. I also have an external battery charger and can guarantee an excellent charge on the battery(s). The current files I was recommended to use came from a single Zipped file: GalaxyNote2UnlockVerizon. Please let me know if there are a different set of files I should be using?
Unless I have downloaded the wrong files? I have attempted to install the following bootloader with Odin versions 3.07, 3.13 and 3.185 and they all fail: BootloaderBaseline2.tar.md5. All I know at this moment i am stuck at a point that I have the Note II in a state that will not allow me to boot.
Lets discuss some hardware issues that I need to explore a little further. Since I have a spare phone to test with I thought I would swap logic/motherboards and see if I had any different results. Unfortunately they are exactly the same on both Note II's. Now comes an interesting issue I stumbled upon. When I VERY CAREFULLY reassembled it on an ESD Mat I somehow dislodged or did not securely fasten the display cable to the logic board and when the power was pressed the phone seemed to start booting but there was no display. The sound and the blue light came on normally. I had hoped the original ROM was now installing. I powered off the phone, removed the battery and disassembled it to discover my mishap, so I reconnected the display cable and reassembled the phone only to see the original problem was still present.
Has anyone else had a charging port issue that caused similar problems? I was planning on ordering a new charging port off Amazon today just to try. Any additional information would be greatly appreciated.
Thank all of you that contribute to this site. It is amazing how many problems can be resolved when great minds are put together.
The red light and wont boot indicates a hard brick...more then likely the device had something flashed to it that corrupted the emmc. Moral of the story...its now a paper weight.
No Red Light
droidstyle said:
The red light and wont boot indicates a hard brick...more then likely the device had something flashed to it that corrupted the emmc. Moral of the story...its now a paper weight.
Click to expand...
Click to collapse
It doesn't have a red light. I can get it into the download mode and it will allow the ROM update through Odin but it will only splash the "GALAXY NOTE II" screen and power off.
jvaldez33 said:
It doesn't have a red light. I can get it into the download mode and it will allow the ROM update through Odin but it will only splash the "GALAXY NOTE II" screen and power off.
Click to expand...
Click to collapse
look for a n7100 tar, or maybe "I think, can't remember" there was a stock tar in the I605 mega roll thread somewhere. flash one of them. Try not to use the kies tar as i've had problems with them being corrupted before. Know you've tried both the methods already. Just a suggestion in case you have not. Also check and make sure you have the right pda file.
Hii,
I have a problem. I cycled to the gym this morning and I was listening music on my Galaxy S3, Ii took the headphones out, put phone in my bag. 10min. later I looked at my phone and there was a strange message with something about the firmware, don't know what exactly. I couldn't do anything else than shut the phone down, now every time I try to start my phone normaly or in recovery the comes a wierd pattern of colors, most of it is white with some other pixels(look at the attached file), I don't know what it could be.. I think it's maybe something with the screen..
Hope someone can help me..
TCon96 said:
Hii,
I have a problem. I cycled to the gym this morning and I was listening music on my Galaxy S3, Ii took the headphones out, put phone in my bag. 10min. later I looked at my phone and there was a strange message with something about the firmware, don't know what exactly. I couldn't do anything else than shut the phone down, now every time I try to start my phone normaly or in recovery the comes a wierd pattern of colors, most of it is white with some other pixels(look at the attached file), I don't know what it could be.. I think it's maybe something with the screen..
Hope someone can help me..
Click to expand...
Click to collapse
Try starting the phone in download mode (volume down+home then power). If it gives the same screen then looks like to need a repair center, you could try a USB jig but that screen pattern looks fatal to me.
If it boots to download mode then follow the guide in general, stickies on how to use Odin on your PC to flash a stock ROM.
ludgseq which
boomboomer said:
Try starting the phone in download mode (volume down+home then power). If it gives the same screen then looks like to need a repair center, you could try a USB jig but that screen pattern looks fatal to me.
If it boots to download mode then follow the guide in general, stickies on how to use Odin on your PC to flash a stock ROM.
Click to expand...
Click to collapse
Hehe, thanks, I totaly forget the download mode, only tried the recovery mode.. It boots and now I try to fix the custom rom or load the clockwork backup.
Well I tried to flash stock rom for the galaxy s3 with odin, but I don´t work. This is what Odin says±
<OSM> I9300XXEMH1_I9300PHNEMG2_I9300CEEMG2_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003>
<ID:0/003> There is no PIT partition.
<OSM> All threads completed. (succeed 0 / failed 1)
Click to expand...
Click to collapse
I never checked partition or something. If the phone is in download mode the product name is empty so: Product name: ..........
I allready chearched for PIT files but don't find one..
TCon96 said:
Well I tried to flash stock rom for the galaxy s3 with odin, but I don´t work. This is what Odin says±
I never checked partition or something. If the phone is in download mode the product name is empty so: Product name: ..........
I allready chearched for PIT files but don't find one..
Click to expand...
Click to collapse
It looks like all of your partitions have been deleted... i think you
need to re-partition. so search the threads on how to repartition. search for the required pit file...
suyash1629 said:
It looks like all of your partitions have been deleted... i think you
need to re-partition. so search the threads on how to repartition. search for the required pit file...
Click to expand...
Click to collapse
The PIT-File is not for every S3 the same, right? I need one for the Europe version, so the normal S3 bought in EU but can't find one.
if yours one is of 16gb model than download the GT-I9300_mx_20120220.pit.zip file from the attachment, extract it an you will get GT-I9300_mx_20120220.pit. For re-partitioning the Galaxy S3 download the pit file from below link and in odin select the re-partition option choosse the .pit file and also your PDA file... and start re-partitioning. hope this works for you.
Note: The above file is only for 16Gb version dont use it if its 32GB or 64GB..
Keep in mind the below things:
GT-I9300_mx_20120220.pit = Galaxy S3 of 16 Gb
GT-I9300_mx_20120322.pit = Galaxy S3 of 32 Gb
GT-I9300_mx_20120329.pit = Galaxy S3 of 64 Gb
Well, big thanks. It was the 16gb version, but I've tried it but it won't work...
Don't know why but Odin gives me this fail, tried it serveral times...
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9300XXELLA_I9300PHNELL2_I9300CEELL1_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Set PIT file..
<ID:0/003> DO NOT TURN OFF TARGET!!
<ID:0/003>
<ID:0/003> Re-Partition operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Click to expand...
Click to collapse
Could it be that my battery is not 70-90%?
I think my phone charges but when plug it in, the same screen appears.
You said that the product name is blank? Then sorry it's an SDS for sure. Send it to Samsung for repair as there's nothing you can do about it.
TCon96 said:
Well, big thanks. It was the 16gb version, but I've tried it but it won't work...
Don't know why but Odin gives me this fail, tried it serveral times...
Could it be that my battery is not 70-90%?
I think my phone charges but when plug it in, the same screen appears.
Click to expand...
Click to collapse
well battery charge is not a problem because i have even flashed a custom rom when my battery charge was 20%. It would be better if the complete firmware file could be found ( with .pit, .tar.md5). it would be better if you send it to Samsung..
I don't think we can do more than this...
Ok, last try please try using this pit file
be warned PIT file may damage your phone and is always a last resort .
Warranty is void .
JJEgan said:
be warned PIT file may damage your phone and is always a last resort .
Warranty is void .
Click to expand...
Click to collapse
But the warranty was already void after root and custom theme. I will try the other pitfile and give report.
But if I send my phone to Samsung what could they do? I don't think they give me a new phone..
TCon96 said:
But the warranty was already void after root and custom theme. I will try the other pitfile and give report.
But if I send my phone to Samsung what could they do? I don't think they give me a new phone..
Click to expand...
Click to collapse
The phone is dead like what I told you earlier. If your S3 is on download mode and you see that the product name is blank that means that the eMMC partition is dead. No amount of PIT files can revive your phone. So if you're gonna give it to Samsung just tell them that you got the SDS. If you're out of the warranty period then you'll probably pay for the repair service.
Your situation is exactly the same as this one: http://forum.xda-developers.com/showthread.php?t=2451728
SignetSphere said:
The phone is dead like what I told you earlier. If your S3 is on download mode and you see that the product name is blank that means that the eMMC partition is dead. No amount of PIT files can revive your phone. So if you're gonna give it to Samsung just tell them that you got the SDS. If you're out of the warranty period then you'll probably pay for the repair service.
Your situation is exactly the same as this one: http://forum.xda-developers.com/showthread.php?t=2451728
Click to expand...
Click to collapse
Thanks, I will visit a walk-in Samsung service center tomorrow. In any case, thank you very much for the offered help . Still things I need to do / not say to the service desk, or it is enough to say that it is an SDS?
TCon96 said:
Thanks, I will visit a walk-in Samsung service center tomorrow. In any case, thank you very much for the offered help . Still things I need to do / not say to the service desk, or it is enough to say that it is an SDS?
Click to expand...
Click to collapse
Things not to say:
1. That you flash a PIT file.
2. You installed a custom rom.
Things to say:
1. Your device had an SDS.
2. Still SDS.
3. Yep. You got it. Still say SDS.
Kidding aside I won't guarantee that they'll buy your alibi since I've haven't visited their service centers for repairs yet (and I hope I won't... ever lol). But most of the service technicians there should know what an SDS is.
SDS is Sudden Death Syndrome if you don't know what that means.
TCon96 said:
Thanks, I will visit a walk-in Samsung service center tomorrow. In any case, thank you very much for the offered help . Still things I need to do / not say to the service desk, or it is enough to say that it is an SDS?
Click to expand...
Click to collapse
Yes, its enough to tell SDS. you don't need to tell anything like it was rooted, custom rom was used. If it was in warranty period was not over tha nyou can claim them by just telling SDS, since there is no partition, neither the product name. So don't tell them anything about all this, you might be serviced for free.. if the warranty is over you have to pay for the repair service.
Samsung's LIMITED warranty is 24 months from dop.
I have a Galaxy S3 GT-I9300 running the Samsung Stock 4.1.2 ROM.
It was rooted and I tried to flash CWM Recovery using Mobile Odinbut as soon as I did that the only thing that now appears when I try to boot the phone is the initial black screen with the "Samsung Galaxy SIII GT-I9300" words.
I cannot get into Recovery mode.
I can get in to download mode but no matter what I try with Odin it sticks at setupconnection. I have used Odin to try and re flash CWM to try and get back into Recovery mode but get stuck at setupconnection.
I have used Odin to try and re flash the stock ROM but again get stuck at setupconnection.
I get this whether I try using Odin on my laptop or my desktop PC
I did wonder if this would happen if my battery charge was low so I plugged the phone in the charger to see what the battery level was when it appeared but the battery will not appear and again I see only the words "Samsung Galaxy SIII GT-I9300" on the black background.
Can anyone suggest a way out of this?
Thanks
matrixmainframe said:
I have a Galaxy S3 GT-I9300 running the Samsung Stock 4.1.2 ROM.
It was rooted and I tried to flash CWM Recovery using Mobile Odinbut as soon as I did that the only thing that now appears when I try to boot the phone is the initial black screen with the "Samsung Galaxy SIII GT-I9300" words.
I cannot get into Recovery mode.
I can get in to download mode but no matter what I try with Odin it sticks at setupconnection. I have used Odin to try and re flash CWM to try and get back into Recovery mode but get stuck at setupconnection.
I have used Odin to try and re flash the stock ROM but again get stuck at setupconnection.
I get this whether I try using Odin on my laptop or my desktop PC
I did wonder if this would happen if my battery charge was low so I plugged the phone in the charger to see what the battery level was when it appeared but the battery will not appear and again I see only the words "Samsung Galaxy SIII GT-I9300" on the black background.
Can anyone suggest a way out of this?
Thanks
Click to expand...
Click to collapse
Which version of ODIN did you use? What kind of file(s) were you trying to flash?
Sent from my GT-I9300 using Tapatalk
I'm not sure but think it was Mobile Odin 3.65 and I was trying to flash CWM touch from xda.
Additionally, I think my battery charge may now be low after many attempts to recover it but will that matter bearing in mind I'm using Odin on my PC and the phone is connected to the PC by USB cable?
One flash Philz recovery and format system data cache and sd card .
Two check your USB drivers for Odin and make sure Kies is not running .
What do you mean Odin sticks at setup connection ??
If its before flashing its drivers or try another version of Odin .
JJEgan said:
One flash Philz recovery and format system data cache and sd card .
Two check your USB drivers for Odin and make sure Kies is not running .
What do you mean Odin sticks at setup connection ??
If its before flashing its drivers or try another version of Odin .
Click to expand...
Click to collapse
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> philz_touch_6.00.8-i9300.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
and it stops there
matrixmainframe said:
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> philz_touch_6.00.8-i9300.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
and it stops there
Click to expand...
Click to collapse
I am reading that as fail before install .
wo check your USB drivers for Odin and make sure Kies is not running .
try another version of Odin .
JJEgan said:
I am reading that as fail before install .
wo check your USB drivers for Odin and make sure Kies is not running .
try another version of Odin .
Click to expand...
Click to collapse
Kies is not installed on my computer and I have tried Odin versions 1.83, 1.85, 3.04, 3.06, 3.07 and 3.09.
I have also tried 'Samsung_USB_Drivers_1.5.27.0.exe' and 'SAMSUNG_USB_Driver_for_Mobile_Phones.exe' and remembering to uninstall then reboot and then install.
On one occasion it got as far as (can't remember the exact words) "Get PIT Mapping" but then just stopped there.
I cannot believe I have done anything other than corrupt the CWM recovery because all I did was try to flash CWM Touch and as soon as I pressed OK the screen went black with the word "Samsung Galaxy SIII GT-I9300". Those words just stay there because since then I can't switch the phone off. I thought that if I just reflashed CWM via Odin on my computer I would be able to get back into recovery mode and just restore my backup.
Appears I am mistaken and have ruined a very new and vey expensive phone.
The only other thing I seem to recall is that before I tried the Mobile Odin flash the battery was below 50% charge but I'm not sure if that's relevant?
This is usually a wrong file flash symptom .
JJEgan said:
This is usually a wrong file flash symptom .
Click to expand...
Click to collapse
Do you mean I'm trying to flash something I shouldn't?
Initially I tried to flash CWM Recovery but then decided just to try and get it back the way it was by trying to flash Android 4.1.2 again.
The file I have been using is "KIES_HOME_I9300XXEMG4_I9300OXAEMG4_1314436_REV00_user_low_ship.tar.md5" which I believe is from Sammobile and which is, I believe again, the ROM that the Galaxy S3 comes pre-installed with. Do you think it worthwhile me trying some other ROM?
I have been doing a lot more web research and some say that the battery charge should be more than 80%. Does this matter?
Won't the battery have been charging all the while the phone was plugged into into the Computer via the USB lead?
If I buy a separate charger and charge my battery to 100% do you think the Odin reflash will work then?
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9300XXELL5_I9300VFGELL1_I9300BUELK1_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Complete(Write) operation failed.
<ID:0/003> Added!!
<OSM> All threads completed. (succeed 0 / failed 1)
so close
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9300XXELL5_I9300VFGELL1_I9300BUELK1_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Complete(Write) operation failed.
<ID:0/003> Added!!
<OSM> All threads completed. (succeed 0 / failed 1)
so close
matrixmainframe said:
I have a Galaxy S3 GT-I9300 running the Samsung Stock 4.1.2 ROM.
It was rooted and I tried to flash CWM Recovery using Mobile Odinbut as soon as I did that the only thing that now appears when I try to boot the phone is the initial black screen with the "Samsung Galaxy SIII GT-I9300" words.
I cannot get into Recovery mode.
I can get in to download mode but no matter what I try with Odin it sticks at setupconnection. I have used Odin to try and re flash CWM to try and get back into Recovery mode but get stuck at setupconnection.
I have used Odin to try and re flash the stock ROM but again get stuck at setupconnection.
I get this whether I try using Odin on my laptop or my desktop PC
I did wonder if this would happen if my battery charge was low so I plugged the phone in the charger to see what the battery level was when it appeared but the battery will not appear and again I see only the words "Samsung Galaxy SIII GT-I9300" on the black background.
Can anyone suggest a way out of this?
Thanks
Click to expand...
Click to collapse
Same here,and i have to load my battery 100% before it gets into 'download mode'again...
Lets see if we can get it up and running again...your not alone...
llcoolveer said:
Same here,and i have to load my battery 100% before it gets into 'download mode'again...
Lets see if we can get it up and running again...your not alone...
Click to expand...
Click to collapse
Nice to know I'm not alone but sorry you're having the same problem. Have sat down to do some more web searching and will let you know if I find a solution
Service centre new motherboard .
JJEgan said:
Service centre new motherboard .
Click to expand...
Click to collapse
Fixxed it by going in the OG recovery....did a hard factory reset and vavooom....fixxed it....:good:
btw,was it a problem that you rooted your phone....? Due to extra costs,or did they bring it under warranty...?
Thanx in advandce for the reply.....
Sincerely ,LLCOOLVEER
llcoolveer said:
Fixxed it by going in the OG recovery....did a hard factory reset and vavooom....fixxed it....:good:
btw,was it a problem that you rooted your phone....? Due to extra costs,or did they bring it under warranty...?
Thanx in advandce for the reply.....
Sincerely ,LLCOOLVEER
Click to expand...
Click to collapse
Please can you tell me what is "OG Recovery"?
Thanks
matrixmainframe said:
Please can you tell me what is "OG Recovery"?
Thanks
Click to expand...
Click to collapse
the Original Recovery....or Stock revovery.....http://www.youtube.com/watch?feature=player_detailpage&v=UvD6ZCENlJA
llcoolveer said:
the Original Recovery....or Stock revovery.....http://www.youtube.com/watch?feature=player_detailpage&v=UvD6ZCENlJA
Click to expand...
Click to collapse
Thanks for that but as I stated in my original post I cannot get into Recovery Mode
matrixmainframe said:
Thanks for that but as I stated in my original post I cannot get into Recovery Mode
Click to expand...
Click to collapse
I couldn't also....only when my battery was full charged....:good:
Succes....
The end
Okay, I started this thread so will end it now as follows:
1 Thank you to all those who offered help/advice/suggestions.
1a Some people do not read posts properly because even though I had specifically stated that I could not get into recovery mode some people proceeded to tell me to go into recovery mode and restore my rom.
2 Whilst I have recovered the full use of my phone I can no longer root it but that's ok because at least I have a phone that is comparable to the vast majority who choose not to root.
3 I will explain how I rescued it but obviously I don't really understand what the result is other than a usable phone so please don't copy.
4 Whilst I have no doubt one could damage a motherboard, that could only be done with very specialist software that most people would not have so the advice of some that I needed a new motherboard was ill informed. If you don't know the answer don't offer an unhelpful answer. Recommending a new motherboard is like a motorist taking his car into a garage with a blown fuse and the mechanic saying the only cure is a new car.
5 After a lot of research I found one lone website that explained that from July 2013 Samsung introduced a change to their ROMs which introduced an efs 2 file. Additionally it appears that once you have flashed/upgraded to an efs2 ROM you cannot then go back to an efs ROM.
6 This is above my understanding but I do know I did go from efs to efs2 and when I then encountered a problem I thought it a good idea to go back to my original (efs) ROM which I now believe caused my problem.
7 I did not know if I had found the answer but as I believed my phone was a paperweight at that point anyway I had nothing to lose and downloaded the GT-I9300.pit file and flashed with repartition selected. I then flashed Android 4.3 knowing it would be an efs2 ROM and my phone is now working again.
8 However, although my phone is now working again, I find that I cannot install a custom recovery nor can I root the phone but that is a small price to pay to have a brand new S3 working again.
9 Whilst it may not be wise to mess about with the pit file, it seems nothing can be lost to give it a go because even if it doesn't work you can still go for the new motherboard option happy in the knowledge you have tried everything.
10 I may start a new thread for advice on that matter but for the time being I'm just relieved to have my phone back and I stress again that it did work for my specific problem and whilst it might work for you please only do it knowing it may not work for your problem.
Hello,
So I accidently deleted a folder of photos vs the one photo i wanted to. In my attempts to recover the photos i tried to root my Galaxy S4 GT-I9505. I tried to use Odin and I kept getting an error saying my phone was removed during the process. I tried mutiple USB ports which no luck. Now my phone is stuck with "Firmware has encounted an issue. Please select recovery mode in Kies & try again." So i downloaded Kies which then told me my phone does not support initialization. so i tried Kies 3 which doesnt support my phone model. I am trying to download the firmware from samsung website, but due to where i am stationed the internet isnt the best. Is there anything a super rookie like me can do? would a factory reset solve my issue? Please help me, I need my phone to keep in touch with my family back home.
Mcrblues said:
Hello,
So I accidently deleted a folder of photos vs the one photo i wanted to. In my attempts to recover the photos i tried to root my Galaxy S4 GT-I9505. I tried to use Odin and I kept getting an error saying my phone was removed during the process. I tried mutiple USB ports which no luck. Now my phone is stuck with "Firmware has encounted an issue. Please select recovery mode in Kies & try again." So i downloaded Kies which then told me my phone does not support initialization. so i tried Kies 3 which doesnt support my phone model. I am trying to download the firmware from samsung website, but due to where i am stationed the internet isnt the best. Is there anything a super rookie like me can do? would a factory reset solve my issue? Please help me, I need my phone to keep in touch with my family back home.
Click to expand...
Click to collapse
If you can boot into recovery, a factory reset can't harm. But it might not fix your issues.
Can you still boot your phone into download mode? If yes, then just download the original stock rom from sammobile.com. It's best to choose the version for your country and carrier. Install it with Odin.
If you still want to root, try chain fire autoroot. Again with Odin.
http://autoroot.chainfire.eu
But after flashing stock Rom, I doubt you will be able to recover your photos. So no point in rooting if you don't care about having root.
Sent from my GT-I9505
Yes i can still access download mode..I think i tried using Chainfire with Odin but Rooting is something for another day. I just want to get my phone operational at a minimum. Im currently trying to download firmware from Samsung-update.com or something like that. Is sammobile.com a better site for me to use? I'm at work right now so I am unable to work on the issue at hand but once I get the stock ROM how easy is it to get on to the phone using Odin?
Mcrblues said:
Yes i can still access download mode..I think i tried using Chainfire with Odin but Rooting is something for another day. I just want to get my phone operational at a minimum. Im currently trying to download firmware from Samsung-update.com or something like that. Is sammobile.com a better site for me to use? I'm at work right now so I am unable to work on the issue at hand but once I get the stock ROM how easy is it to get on to the phone using Odin?
Click to expand...
Click to collapse
Samsung-updates is just as good.
The firmware you download will probably be a zip file. You should extract it if it's a zip. You should end up with a file with the extension: tar or tar.md5.
You have to boot your phone into download mode.
Start Odin on the pc in administrator mode.
Connect the phone to the pc. Use the original USB cable that came with the phone.
You should see the text: in Odin when you connect the phone.
Put the firmware you downloaded in Odin in PDA or if you're using the latest version, in AP.
Make sure only: "auto reboot" and "f. Reset time" are checked.
Click start and wait until your phone restarts. (10 minutes or more)
You're done.
EDIT: one more thing, make sure Kies isn't running in the background. It might interfere with Odin.
Sent from my GT-I9505
<ID:0/004> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9505XXUGNF6_I9505H3GGNF2_I9505XXUGNF6_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Odin v.3 engine (ID:4)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Get PIT for mapping..
<ID:0/004> There is no PIT partition.
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/004> Removed!!
<ID:0/004> Added!!
<ID:0/004> Removed!!
Ok i want to start by saying i love you both for helping..I got my phone back!!!!!
and ive learned my lesson in rooting..dont do it because im dumb