I have an HTC Radar 4g, and im trying to install a custom rom onto it, but I cannot get past the spl part. I'm not even sure if i'm using the right spl downgrade
When i boot the device using the vol+ and vol- I get this information, does anyone have a link for what spl ruu i need?
PI06110
SPL-4.6/175006.2(140280)
RADIO-17.5006.08.27
Related
I am currently trying to downgrade my spl before sending my phone to be repaired. I am following the Mrvanx guide. Unforunately, I am sending my phone back because the screen input no longer works. Therefore, I can't get past the windows mobile setup screen. So, I can't get activesync to work and therefore can't force use SSPL to downgrade my SPL.... ( RUUWrapper doesn't think there is a phone connected)
Does anyone have any suggestions?
Cheers
Simon
cook a rom with the touchscreen alignment disabled.
Mudstuffin said:
I am currently trying to downgrade my spl before sending my phone to be repaired. I am following the Mrvanx guide. Unforunately, I am sending my phone back because the screen input no longer works. Therefore, I can't get past the windows mobile setup screen. So, I can't get activesync to work and therefore can't force use SSPL to downgrade my SPL.... ( RUUWrapper doesn't think there is a phone connected)
Does anyone have any suggestions?
Cheers
Simon
Click to expand...
Click to collapse
Which bootloader are you on??
Same as you:
IPL: 1.04
SPL: 2.10.Olipro (HardSPL v7)
I'm trying to do the two part process of downgrading...
Downloads the CHT original rom
Were you able to downgrade? I'm in the same boat, no screen taps and can't downgrade to 1.10.
Read Mrvanx's SPL downgrade guide but it fails with a comm error during the 2.10 to 1.10 downgrade using hard-sspl. If I select 2.10 as the boot loader it seems to load the spl ( gives me progress bar) but when I go back to the boot loader it's still at 2.10 Olipro.
My touch screen is dead and have to return for warranty after receiving replacement or AT&T going charge me. Screen always stuck at " Tap Hear to setup".
Thanks.
Bypassed aligment and was able to downgrade
In case some poor schmoe finds this in the future, I was able to get around the screen alignment and downgrade my spl.
I found how to bypass welcome screen here:
http://forum.xda-developers.com/showthread.php?t=218992&referrerid=366117
Once I did this, I was able to say "Yes" to running enterbl.exe and downgraded to olipro 1.10 using mrvanx's guide and then re-flashed the original cingular ROM which also flashed spl.
after update my hermes my phone dosent start windows after another upfate with a shipped rom the phone finish the update but stil dident start windows any suggest
ipl.1.01
spl 140 olipro
londere said:
after update my hermes my phone dosent start windows after another upfate with a shipped rom the phone finish the update but stil dident start windows any suggest
ipl.1.01
spl 140 olipro
Click to expand...
Click to collapse
You might need to reflash it. Hold the two soft keys and then push the reset button. it will ask to hard reset. If the phone fails to come on after the hard reset, then hold the left 'ok' key and the power button, and then push the reset under the phone- this will take you to a tricolor screen where you can then re-flash the phone. try reflashing with official rom's, before using any other roms.
yes i do but it still in boot any sugest ipl 1.01 spl 1.40 olipro if any know how to update ipl with hard spl or how to remove hard spl it will be aprecible
My suggestion would be to try using sd to reflash the rom and see if that orks. format sd card making sure its fat 32 then put .nbh file in root directory. rename to herimg.nbh then insert into phone. go to bootloader and it should start the flash straight away. if this works make sure you upgrade spl to olipro 2.10 hard spl so its easier if there are problems. you can possibly upgrade spl this way too (get nbh file and rename hermimg.nbh). I tried this on my herme 100 and it seemed to work. it will flash the spl BUT when it restarts it will go straight to bootloader and start flashing again. as soon as it restarts get the sd card out and put on the os you want to flash. insert card and as long as you've named it hermimg.nbh it should flash new os with spl olipro 2.10. Good luck flashing.
You should read the wiki first : http://wiki.xda-developers.com/index.php?pagename=Hermes_Unbrick
your phone can be unbricked using the information on wiki.
only enter to bootloader the ipl dosent start also i fla**** but it stil apear spl.140oli whei in flash it with hard spl 1.10 and when i flash it with spl 2.60 oli it send me a error i try to flash it with qtek-cingular-doppod roms and nothing any suggest
any fu**ing suggest?
also it avoid me to update spl im stuck on hard spl 1.40 and ipl 1.04 i try to flash hspl 260-210 but it refiuses to stay in 1.40 radio 1.27 patched the ipl works but it frezzes with the green led dosent apear nothing
my device still blocked in boot mode i dont know if it is briked the device had the following info
ipl 1.04
spl1.40 oli
radio maybe no
os no
any suggest
any sugest to save my hermes
follow the unbrick guide link that koorosh_bsboys posted
it cant be unlocked its stuck in spl 140 olipro
did you follow the unbrick guide that koorosh_bsboys posted?
just stop trying any unauthorised ideas. let me know if i can help u. i have a friend in o2 service centre here in india. he can get ur device working. he does it by help of a software and 3 cables . it takes about 2 hrs. just let me know if u want ur device to work again
stil zombie my device im getting crazy any ideas
londere said:
stil zombie my device im getting crazy any ideas
Click to expand...
Click to collapse
If you want people to help you, you have to help yourself first!
1st of all, have you gone to read the Wiki as suggested?
2nd what methods have you tried to unbrick your device?
If you can't answer these questions then we can not help you, you keep asking for suggestions but you do not even reply to other's questions!
Here's a good place to start helping yourself if you haven't already http://forum.xda-developers.com/showpost.php?p=1465974&postcount=1
Hi, I was unlocking my htc 8525 at&t but i was using vista and my cell keep in Type 2a: When the phone boots, it goes directly to bootloader mode (tri-color screen)
what can I do to fix it... tks
Whats the info for your SPL?
Hi, I got my Hermes 8525 in boot mode what i did is to install this Schaps_WM6Pro_WWE_4.00_Full.exe now my hermes is working but i want to unlock it..what can I do cos everytime i try got in to boot mode again..any help tks.,..
SPL- 1.40
Try unlocking it with Windows XP
hi, i tried in win xp but keep the same in boot mode...
On the PC, in activesync settings, untick "Allow USB Connection".
Put Hermes into bootloader (tri-colour screen) and then run the RUU_Wrapper.exe file of the unlocker program. Follow all the instructions to unlock your Hermes and once its unlocked put Hard SPL V7 on it BEFORE flashing any thing else. After flashing Hard SPL V7, go back to bootloader and check SPL is 2.10 oli.
You now have a Hermes that is easier to recover if somehing goes wrong with a flash, excluding radio rom flashes.
Cheers...
Hi, canu put the link of the program u told me to use..tks for your help..
RUU_Wrapper.exe, Its included in any rom you want to flash. Its how you flash using the PC...
Hard SPL is in the sticky of the Hard SPl thread in upgrading section.
first off i would like to state that i will pay anyone $25 who can help me figure this out. i have paid plenty of people through paypal for their assistance in the past. so here it goes.....
i had CM7 on my hd2 Nand android 2.3.3, i need to turn it back in for services and need it to be stock again. i have looked online for resources on how to do this and i managed to get it back to stock however the SCREEN DOES NOT WORK!!!! it comes on, but it does not respond to touch. i have tried resetting it. but all it does is go to the setup screen and i cannot skip any of the steps. ALL THE HARD KEYS WORK THOUGH!!! JUST NOT THE TOUCH SCREEN.
my mother has a regular un-abused hd2 and when i acces the RedGreenBlue screen it gives me this information (as we all know all of the info is on the top Red portion of the screen): PB81120 HX-B3
SPL-2.10.000 8G XE
MicroP(LED) 0X05
MicroP(Touch) 0X40
on my HD2 i get: PB81120 SS-B3
SPL-2.08.0000 8G XE
MicroP(LED) 0X05
MicroP(Touch) 0X50
what am i doing wrong and does this have anything to do with the phone not responding to touch input?
additional info: my mothers hd2 has: Rom 3.14.531.1 wwe (04666)
Radio 2.15.50.14
OS 5.2.21913
manilla 2.5.20181424.0
anyone? please?
assuming its a tmous (green send key red endkey) then get a stock tmous rom (and ONLy a stock tmous rom, not any other rom, go through the t mo website just to be sure, , a non tmous rom will brick it (( course if its under warranty, then that type of brick would still be accepted, lol))
anyway, get the stock tmous rom, put phone in bootloader (stripey screen) connect usb, run the romyoudownloaded.exe
PB81120 is T-Mobile US version.
To get ROM 3.14 for your HD2 go there http://dl.htc.com/ruudownload/t-mobileUS/Filedownload.aspx?pid=leo and enter your IMEI or search XDA forum for another download link.
Use sd card method for flashing STOCK ROM. See this TUT: http://forum.xda-developers.com/showthread.php?t=653614
ok guys i will try what above recomendations thanx.
Edit: i did manage to to return back to stock before. the only problem is that the touchscreen would not work. it came on and saw the startup screen. when the phone went to the set-up screen i tried to skip the set-up process to start using my phone right away. but it was NOT responding to my touch. so i figured that i did something wrong. anyone ever have a problem with the touchscreen not working? it worked fine when i had cm7 hyperdrois on it.
i downloaded T-Mobile_HD2_MR_Software_2.13.531.1 from the tmobile website. it doesnt have a .ruu or .nbh extension. In the tutorial to flash via SD card it states:
1. Make sure your microSD is Formatted to fat32 (you dont have to delete all files but it is safer if you do)
2. Download your prefered Rom from the LEO Rom Develpoment Page and unzip/unrar it to your PC
3. Goto the Roms Folder and rename the .nbh file to LEOIMG.nbh
4. Copy the LEOIMG.nbh file to the root of your MicroSD Card
5. Plug the MicroSD Card into the phone
6. Reset the device while pressing the volume down button to enter the BootLoader screen, you will first see a tri-color screen with the phone and SPL Information at the top
7. Follow the On Screen instructions to start the update
8. After flash has completed, press the reset button with the stylus to reset the device.
the rom i downloaded is not zipped and it shows up as an application.
i am not quite sure how to do this with the real rom from tmobile...do i put offcial rom from tmobile unto sd card and try to flash it?
thank you guys for your help so far this is all greatly appreciated.
The download is an exe, yes, but really its an executable zip. You can..
Change tgw extension from exe to zip
Or
Right click it and choose "open with (insert name of whatever program you have installed to handle zips)"
Or
Run the exe, and it will extract itself into 8 or so files, copy the one you need before cancelling the running program.
However,since you already have stock spl, there is no need to use SD card method, just put phone in bootloader, connect USB, run the exe.
I have done that. But the touchscreen does not respond to my touch. I cant get passed the set-up screen cause i cant press the "skip" button. I have ran the .exe application about 3 times and i have my stock winmo 6.5. Why my touchscreen not working?
Sent from my HTC Glacier using XDA App
Should i try SD since i have done it through USB 3 times?
Sent from my HTC Glacier using XDA App
Lol, cos its broke, isn't that why in your first post you said you wanted it back to stock to go to service?? Well, now its stock and you can send it in.
My hd2 charging inlet is broke so i have to use my mother's hd2 to charge my battery and put it back in mine. Has nothing to do with screen. When i had pongsters cm7 it worked. Occasionally the screen would not respond. Any help please.
Sent from my HTC Glacier using XDA App
ahhhh gotcha. no, sorry, not seen a fix for that. (got one with an unresponsive screen myself, happened last night, totally out of the blue, , glad i bought a replacement last month!)
So basically i am SOL? And i now have to send it in for both services. I should be okay since when they boot it up it will show a stock rom right? I have been hearing alot about hd2's screen going out like that. I guess it has to do with "resistor" burning out? So based on my info on my first post, my HD2 is back to stock right?
Sent from my HTC Glacier using XDA App
The key to warranty is the spl,, so yes yours is fine.
Iam using Win 7.5. So is there anyway to upgrade to android or Win 7.8??
Since the official 7.8 isn't out yet, your only option is custom firmware. For that you need to downgrade your spl to 2.05, there are many guides to follow, including some in this forum. Includes the RUU for the 2.05 spl, try running it with your phone in download mode, both volume buttons and power button pressed together, for some thats it, than flash hard spl and you are able to install any custom rom. If you are prompted with error message while flashing spl, than make a gig (Y cable, gold card) with explanation and video tutorials in this forum.
Next time try searching before boldly opening a new thread.:cyclops: