[Info] Some tips for (Droid) Razr Maxx battery conversion - Motorola Droid RAZR

I've just successfully converted my GSM Razr to a Maxx today and like to share some of the experience...
As basic orientation, the instructional video from CRS is okay, together with the images on Ifixit.com they provide good help, although they fall a bit short at some points.
The following only reflects my own opinion/experience... if you're not as clumsy or cautious as I am - good for you.
Stuff you need to get:
Get the black maxx PCB frame. And get a replacement camera bezel.
T3, T4 and T5 Torx screwdriver. Yes, T4 too, wait till you read why.
For opening up the phone and handling parts, you need these as well:
I needed each one of them and besides the Torx, nothing else was required.
Get a bunch of these for cheap on Ebay. Color or vendor don't matter, they're all made of the same stuff.
The tools you don't need:
iSesamo... don't order it. And don't use it if you get it sent to you nonetheless (like in my case). It's made of metal.
Not only can it easily get you some nasty dents/scratches at the side of the housing, it can, when being handled unfortunately, destroy the electronics on your phone's motherboard... you don't want that.
The spudger.. I don't know, I didn't need it at any point
Here are some additions to the CRS & Ifixit documentations:
I) In CRS' video and on the Ifixit website, you will read that T3 + T5 screwdrivers are required. Unfortunately, they both either made a mistake, or the production process has been altered, because T4 is needed as well; actually, all but 3 (of all those described as T3) were infact T4 torx screws. Imagine my heartbeat when I tried to use a T3 on the screws and it didn't fit
II) I did (negligently) break the camera bezel while removing it. If you don't use a heatgun/dryer to losen the adhesive beneath it, you will almost certainly break it. And that's ok, because a replacement bezel costs 6$, while damaging stuff like the rear camera with too much heat costs almost tenfold.
I honestly can't tell if it is really dangerous to heat up stuff like the camera or not, I just didn't want to risk it.
III) Opening the phone and removing parts is a pain in the ***. You're brest served using...
- The thick long prying tool and the thick plectrum for opening the housing.
- The thick long prying tool to remove the the PCB frame.
- The slim long prying tool for removing the speaker from the old housing without damage (don't use a screwdriver or so)
- The slim long prying tool for removing/replacing the battery pole rubber cover and the mic rubber grommet.
- The slim plectrum to slide it under the battery and losen it before even thinking about pulling the "battery removal" grip.
- The slim plectrum or the slim prying tool for losening sensitive parts of the housing (e.g. sim door)
Generally, opening/removing parts is a hassle but if you take your time and exercise medium caution, you won't damage anything of value.
IV) CRS delivers (or at least did in my case) only 1 piece of double sided adhesive to stick the back side of the new battery, while the original battery has adhesive on BOTH sides.
V) Test run your device after you inserted the new battery (and secured its screws). If everything runs ok, then proceed to snap on the black housing frame and the back cover.
VI) Make sure the housing frame and back cover snap on tightly (=correctly) at every single spot, ESPECIALLY at the SIM card door.
I recommend starting to snap on the back cover exactly at that spot, making sure that the thin lower frame part of the SIM card door snaps on tightly. If you mess up that spot, you might be unable to correct it without re-removing the entire back door.
That should be sufficient for now...
Oh BTW:
The back door cover delivered by CRS has a fat "4G Verizon" writing on it. Live with it -.-

Related

Back Cover with Reset Hole?

Does anyone know if there is a third party Touch HD cover with a reset hole, so that we can perform reset wihtout having to remove the back cover?
I usually try to reset by software, but often this is not possible because the device is frozen, in which case I would remove the back cover and take off the battery.
How much more convenience there will be if I can just poke into the reset hold without removing the cover, isn't it?
why not just drill the cover yourself?
What tools do you use for this drilling job? How do you get it at the correct position? Will the paint around it come off if an amateur does the drilling?
I would love one with micro SD card hole. But I would need an extra back cover to have that as backup.
Try it with one of these: http://cgi.ebay.co.uk/Housing-Batte...3286.c0.m14&_trkparms=66:2|65:2|39:1|240:1318
It is a relatively simple task drilling a hole, or making a cut-out.
I would suggest buying a spare back cover first though.
You will need;
something like a 2.5mm drill bit (just got HD like an hr ago not had chance to play with it or make measurements), 2 bits of masking tape, a small ruler or measuring tape, something to protect the back when laying it on a suitable surface to drill on.
Accurately measure where the button is in relation to where the hole is to be.
Put the Masking tape either side of the back roughly where the hole will be, then carefully transfer the measurements over on to the back and mark on the tape where the hole will be.
Using a suitable bit, while resting the back on something to prevent scratches, drill the hole.
Please note having a hole may increase chances of dust and lint getting into the battery compartment - you could resolve this by getting a small 10mm square piece of foam (same kind as used in light traps in cameras - its pretty thin).
For the Micro SD cut out, sorry you'll need to ask me later once I've had a chance to have a proper look.
Feel free to PM me
It is a relatively simple task drilling a hole, or making a cut-out.
I would suggest buying a spare back cover first though.
You will need;
something like a 2.5mm drill bit (just got HD like an hr ago not had chance to play with it or make measurements), 2 bits of masking tape, a small ruler or measuring tape, something to protect the back when laying it on a suitable surface to drill on.
Accurately measure where the button is in relation to where the hole is to be.
Put the Masking tape either side of the back roughly where the hole will be, then carefully transfer the measurements over on to the back and mark on the tape where the hole will be.
Using a suitable bit, while resting the back on something to prevent scratches, drill the hole.
Please note having a hole may increase chances of dust and lint getting into the battery compartment - you could resolve this by getting a small 10mm square piece of foam (same kind as used in light traps in cameras - its pretty thin).
For the Micro SD cut out, sorry you'll need to ask me later once I've had a chance to have a proper look.
Feel free to PM me
As above & using my trusty Dremmel in its drill press to get an accurate location.
Although, I'm also not too keen to have an 'open' hole on my case.
For an micro SD cut out cover, suppose you could use a small piece of sheet rubber: leave 2 lugs either side to secure the flap when closed and secure the flap to the back.
Or you could perform something approaching micro surgery and construct a carrier for it that replacesthe bit cut out for the hole.
why not install
holyfox's_poweroff-diamond.cab
ljazzo1 said:
why not install
holyfox's_poweroff-diamond.cab
Click to expand...
Click to collapse
Read the first post - he wants this for when the device is frozen and a software reset would not be possible.
iPhoneLCD superior to Blackstone! but Blackstone practical than the iPhone!
I just bought a Boxwave 2500mah extended battery that comes with a extended battery door for my Touch HD and I think its pretty easy & possible to make reset hole for the battery door. You just need a really pointy and sharp exacto knife to puncture the plastic battery door and then just rotate the knife until you get your desired size of the hole. Tried this many times when I was still playing with "Lets Go Tamiya Cars".
About the hole for the microSD card, I think this one will be a little tricky to do because you might hit one of the locks for the door upon modification.
eaglesteve said:
Does anyone know if there is a third party Touch HD cover with a reset hole, so that we can perform reset wihtout having to remove the back cover?
I usually try to reset by software, but often this is not possible because the device is frozen, in which case I would remove the back cover and take off the battery.
How much more convenience there will be if I can just poke into the reset hold without removing the cover, isn't it?
Click to expand...
Click to collapse
Hi eaglesteve,
If the device is frozen, can't you just reset by holding the power key down for 3 seconds? This should always kill the power, leading to a soft reset when you turn it back on. It's my preferred method for tboth the Blackstone and Diamond products.
mike.waters said:
Hi eaglesteve,
If the device is frozen, can't you just reset by holding the power key down for 3 seconds? This should always kill the power, leading to a soft reset when you turn it back on. It's my preferred method for tboth the Blackstone and Diamond products.
Click to expand...
Click to collapse
The problem is that the Blackstone requires a touch confirmation and this is usually not possible when the device is frozen.
Hi,like this ?
Marcdu81 said:
Hi,like this ?
Click to expand...
Click to collapse
this is crazy... why are u people drilling the cover when u can slide it out normally ...
Hi,
Where i can find a back cover with reset hole?
Thanx
I think you will have to buy a replacement battery cover and drill a hole in it yourself

Secure Ram Mount AQ3 Bike and 4x4 mount for Touch HD - Detailed Mod

Hi All
When I looked around for a bike and car mount for my Touch HD I wasn't very happy with what was available.
Specifically I wanted a 'protective' mount that would keep the phone dry and dirt/mud free, I also wanted to be able to leave the phone in the unit and step away without someone being able to grab the phone easily (I realise if someone wants to steal it they'll do it, however I want to at least slow them down if they try).
After searching I found the Ram Mount AQ3. It seemed perfect as it had a clear cover and was lockable, however it was 2mm too narrow to fit the phone.
Dremel time.
http://www.ram-mount-uk.com/ram-hol-aq3.htm
To achieve the following you need about an hour of time, a Dremel with standard fittings, a steady hand and a bit of concentration. If you've not used a dremel on plastic before I'd suggest practising on other tough plastic to get an idea of how the dremel reacts before going to work on your RAM Mount.
Please follow all the standard safety precautions using your Dremel, it's not my fault if you cut off your finger or an exploding bit blinds you.
The plan was to increase the internal width of the mount by about 1mm on each side and to have a cutaway that would allow a mini usb connector to fit the phone while it is in the mount.
IMPORTANT NOTE
Do NOT use the Dremel on a high speed setting, this generates heat and causes melting rather then the grinding you need. I used my Dremel on the lowest speed setting and constantly moved the area being worked on, after about 2-3 minutes on a 'side' I'd change to the other side to ensure the plastic didn't get heat buildup that would cause melting.
I decided to use a Dremel grinding tip to achieve my objective, specifically...
http://www.dremel.com/en-us/AttachmentsAndAccessories/Pages/AttachmentsDetail.aspx?pid=932
Make sure the Ram Mount is securely positioned and that you have good access to allow you to work across both the internal sides you want to grind. TAKE YOUR TIME.
You want the whole side of the Dremel bit to be in contact with the plastic, try to avoid angling the bit as you'll find that either just the top edge or bottom edge of the bit will be grinding the plastic.
Working in a smooth consistent way start to grind the internal area of the mount on one side, work gently from side to side on the area and do not stay on one part too long, heat buildup and melting happen surprising quickly and plastic will not grind if it's melting. Do not press down on the plastic too hard, let the bit do the work for you.
After working both sides say 5 times get a vacuum cleaner and remove all the ground residue that is in the area, use your finger to rub the internal areas to remove any small particles and vacuum thoroughly again.
Install the two thin padding sheets supplied with the mount and then install the phone.
Test to see if your phone now fits flush, if not try to identify the areas where you need extra grinding and rework them, try to ensure you remove equal amounts from both sides of the Mount. Always vacuum before trying to mount the phone, the dust grinding produces is extremely small and could get inside your phone if you're not careful.
When you're satisfied with the flush fit you then have to remove some extra plastic from the area near the volume buttons, with the phone fitted visually identify the top and bottom position where the buttons sit and spend maybe 2 minutes further grinding that area. Vacuum and install the phone to ensure the buttons are not pressed when the phone is fitted, repeat till you're happy.
You should now be able to mount your phone, fit the clear plastic cover and close and lock the lid, this should all be possible without the volume buttons reacting inside the case.
If you've got here well done, the next step is fairly straightforward.
With the phone fitted identify where the mini usb connector is on the phone, mark or score the plastic at both ends of the connector, remove the phone from the mount.
Using the following cut off wheel cut into the mount at the previous two marks.
http://www.dremel.com/en-us/AttachmentsAndAccessories/Pages/AttachmentsDetail.aspx?pid=409
Again be careful using the cutting tool, the plastic will heat up and melt quite quickly.
Once you've cut down into the plastic on both the marks then cut at a 45 degree angle into the plastic that's going to be removed, you want to cut a V shape within the marks. Using the cutting tool keep working to remove blocks of plastic within the marks until you can mount your phone and connect a mini usb connector.
That's it, you should now have a secure lockable box that your Touch HD fits in perfectly.
Good Luck
Sorry about the photo quality, my flash camera is elsewhere at the moment.....If people are interested I'll take detailed photo's next week.
Case Closed
Case Closed with Cover in Place
Mini USB Cable attached
Any pics of the result ???
Thank you very much for this tips.
Photo's added above
i got this one crackinbg box
http://www.otterbox.com/handheld-pda-cases/1900-series-pda-case/
jez

[Q] HD2 - Cannot remove housing

Hi,
I recently purchased a HD2 on eBay. It was supposed to come immaculate but unfortunately there are dents on almost all corners. Rest if perfect.
I saw on eBay some chinese sellers selling new housing + battery covers for ~25 USD. So why not replacing the housing then? I decided to give it a try.
Well I have to say that it really did not work like in the videos I saw on youtube. I removed the 4 screws under the battery cover, gently pressed the back of the LCM outward but it really refused to pop out (no even half an inch). I discarded the pry tool (a very thine credit card actually) and even tried using a suction cup on the digitizer to pull it backwards but same problem. It's like the LCM/chassis was glued on the bezel. Phone has never been disassembled before (white sticker and void screw were still both there).
This is strange because in all the videos I saw the LCM/middle chassis was clearly not glued on the bezel. It immediately popped out a bit then you could start prying (and praying!). Ok I know that in those videos usually the phone has already been disassembled before so other attempts require less force to do it again for the recording.
My questions now to all the people who managed to do this. Did this require so much force? Is there a change and is HTC now glueing this part the LCM/middle chassis to the bezel? Any suggestion? Where is for you the best place to insert the pry tool when you start?
Thanks and regards,
Try flexing the plastic bezel above the earphone outwards a little while applying slight pressure to the sticker area on the back. There're two notches above which locks the frame to the pcb.
Hi,
Thanks for your help.
I will try that later.
I guess I might need to find a better pry tool.
BR.
Ok I managed to do it.
This required clearly some force on the pry tool (actually I used two plastic cards : a very thin and flexible one than a credit card). I started the operation above the earphone area.
Applying pressure on the sticker area was stresfull because the LCD immediately reacted to the pressure (hence a risk to break it or damage it). Best was to put two fingers on the sticker area to help the LCM module to pop out but with (almost) no pressure.
I had a doubt and now that I managed to remove the housing it's gone. The antennas (those white stuff you see in both top corners and at the bottom) are glued to the housing.
I prefer to spend a few more bucks to take a housing which has those antennas already in.
BR.
i had a similar frustrating experience to yours in trying to snap the back off the chassis on my hd2 which had a fingerprint on the *inside* of the camera cover glass which i needed to open it to get at.
it sure looks easy in that HTC disassembly video on youtube but the tech there is using a sort of plastic hooked tool for the job, which i didn't have, so i used my thumbnail instead in the same place (the upper left corner, looking at the phone from the front) and it took me a good 20 minutes of applying what seemed like unreasonable pressure to my touchscreen and nearly tearing my nail off to get it to pop out.
those snap-tabs the electronics manufacturers use to hold cases together -- even when they also have screws to do the job -- are one of my all-time pet hates. i usually end up breaking them off.
I will be doing the same thing soon. So the housing you removed has antennas glued to it ?. Thanks for that, I will try get new housing with antenna together if possible.
I replaced my screen a while back and can confirm the main body of the hd2 is glued to the sides of the chassis.
It does come out but with a lot of force but pry the glue lose around the whole chassis first by sliding a thin card right ot the bottom of the case and slowlyu move and pry it upwards with 2 cards one on the top and other on the right after you losend the glue. the top has the wifi adapter n that so be careful bottom has usb so mite break.
honestly i would say don't bother replacing it and just get a gel case or something to hide the damage. there's a high chance of messing the digitizer up and would just cause you more trouble of taking the whole phone apart bit by bit and trust me the components are tiny so easily breakable especially the ribbon cables they decided to use. my honest opinion don't
fallenmonk said:
I will be doing the same thing soon. So the housing you removed has antennas glued to it ?. Thanks for that, I will try get new housing with antenna together if possible.
Click to expand...
Click to collapse
yep they are white thin bits glued to the top portion of the case. wifi on left and phone on right if i remember. its been quite a while though since i took my old hd2 apart
Now that I know how to do this I will be easier next time.
Yes antennas are glued in the housing so best is to buy a housing which has antennas already in.
Important note : the antenna which is at the bottom of the housing exists in two different versions : EU or US so check with the seller which one he sells.
BR.
Top left : Amphenol-BT&Wifi-090820
Top right : Amphenol-GPS-090820
Bottom : Amphenol-EU-090828
If T-Mobiles US you need Amphenol-US
sirec said:
I replaced my screen a while back and can confirm the main body of the hd2 is glued to the sides of the chassis.
It does come out but with a lot of force but pry the glue lose around the whole chassis first by sliding a thin card right ot the bottom of the case and slowlyu move and pry it upwards with 2 cards one on the top and other on the right after you losend the glue. the top has the wifi adapter n that so be careful bottom has usb so mite break.
honestly i would say don't bother replacing it and just get a gel case or something to hide the damage. there's a high chance of messing the digitizer up and would just cause you more trouble of taking the whole phone apart bit by bit and trust me the components are tiny so easily breakable especially the ribbon cables they decided to use. my honest opinion don't
Click to expand...
Click to collapse
i don't believe it's glued. as far as i can see the the case is held together with screws and plastic interlocking tabs. the trick is to get the latter to unclip.
No glue indeed just notches locking the LCM module to the bezel
Ok case closed
I got my new housing and the replacement went fine. For those who could be interrested I bought it on ebay from the seller forceviewer_uk in China. Everything went perfect so I can recommend this guy.

[Q] HTC Rezound - Digitizer replacement questions

Just 35 minutes ago my phone fell from my hands and onto some cable in the perfect way that it broke the Digitizer. Wonderful. So now I have to go about replacing this. It looks pretty straightforward and I will be doing this but I have a few questions I'd like to see if I can get answered. Perhaps this can be used by others as a helpful FAQ regarding replacing the LCD or Digitizer on an HTC Rezound.
1) I know I will be needing the Digitizer only as the LCD portion is not broken, so can anyone give me a good reason why I should replace both and not just the digitizer?
2) I know there are some adhesives involved in holding it together. Are these re-usable or should they be replaced? If they should be replaced, what kind of adhesives are they and where can they be found?
3) What is a good source for these parts? (Adhesives and digitizer)
4) Is there upgrades here I can do? Like a gorilla glass digitizer or something?
5) I've read a guitar pick is a great tool to separate parts, do you agree?
6) Any Gothca's that I should be concerned about
Here is the procedures I will be following:
1) Remove the back cover, the battery, SIM card and SD Card
2) Remove the 6 T5 torx screws around the sides (from the back)
3) Pry up the back by releasing the plastic clips around all 4 sides (note the volume rocker/power button may fall out)
4) Remove the Vibrator motor
5) Remove the two screws holding the MoBo on and lift up from the USB port side and remove the plastic piece from there.
6) Release the small plastic clips holding the Mobo in and swing it up, release the two ribbon cable connections
7) Heat around all sides front and back to loosen the adhesive, from the back work with a guitar pick to loosen the adhesive, repeat this process from the front.
8) Work around with the guitar pick between the screen and the housing from the front and remove the LCD and digitizer from the housing
9) Heat all the sides of the LCD/digitizer to loosen the Adhesive
10) Work with the guitar pick around the sides to release the digitizer from the LCD screen. It seems there is a piece of black tape on one side, you would have to "butterfly" the two screens and peel the screens apart.
11) Done. Reverse these steps to rebuild it. Do these adhesive parts need the adhesive replaced? Does the tape need to be replaced?
I cannot post links yet, but I felt I should give credit where its due. To obtain these steps I used a Youtube video. To view this video, search youtube for: 'How To Fix HTC Rezound Screen by RepairsUniverse.com'
The advice from the experts is highly anticipated!!
Regards,
Eduard Tieseler
The best reason for replacing both is that you won't have to worry about binding them or getting dust between them if you get them together preassembled. As to the rest, I can't say. I know we have a few people here who have done it.
So I found the adhesive strips that I need. It comes as a bulk sheet where you cut them to fit. I am going with replacing only the digitizer. Replacing the LCD screen also would male the process easier however I fear getting a replacement screen that is in worse shape or more poorly made than the original one my phone came with. I know this one has no flaws.
So I have answered my questions already. I'll post here when I done replacing the digitizer with anything that is of interest in case someone else has questions about this procedure.
Thank you for your input shrike1978. Much appreciated.
Regards,
Eduard Tieseler
Sent from my Infected HTC Rezound using xda app-developers app
etieseler said:
Just 35 minutes ago my phone fell from my hands and onto some cable in the perfect way that it broke the Digitizer. Wonderful. So now I have to go about replacing this. It looks pretty straightforward and I will be doing this but I have a few questions I'd like to see if I can get answered. Perhaps this can be used by others as a helpful FAQ regarding replacing the LCD or Digitizer on an HTC Rezound.
1) I know I will be needing the Digitizer only as the LCD portion is not broken, so can anyone give me a good reason why I should replace both and not just the digitizer?
2) I know there are some adhesives involved in holding it together. Are these re-usable or should they be replaced? If they should be replaced, what kind of adhesives are they and where can they be found?
3) What is a good source for these parts? (Adhesives and digitizer)
4) Is there upgrades here I can do? Like a gorilla glass digitizer or something?
5) I've read a guitar pick is a great tool to separate parts, do you agree?
6) Any Gothca's that I should be concerned about
Here is the procedures I will be following:
1) Remove the back cover, the battery, SIM card and SD Card
2) Remove the 6 T5 torx screws around the sides (from the back)
3) Pry up the back by releasing the plastic clips around all 4 sides (note the volume rocker/power button may fall out)
4) Remove the Vibrator motor
5) Remove the two screws holding the MoBo on and lift up from the USB port side and remove the plastic piece from there.
6) Release the small plastic clips holding the Mobo in and swing it up, release the two ribbon cable connections
7) Heat around all sides front and back to loosen the adhesive, from the back work with a guitar pick to loosen the adhesive, repeat this process from the front.
8) Work around with the guitar pick between the screen and the housing from the front and remove the LCD and digitizer from the housing
9) Heat all the sides of the LCD/digitizer to loosen the Adhesive
10) Work with the guitar pick around the sides to release the digitizer from the LCD screen. It seems there is a piece of black tape on one side, you would have to "butterfly" the two screens and peel the screens apart.
11) Done. Reverse these steps to rebuild it. Do these adhesive parts need the adhesive replaced? Does the tape need to be replaced?
I cannot post links yet, but I felt I should give credit where its due. To obtain these steps I used a Youtube video. To view this video, search youtube for: 'How To Fix HTC Rezound Screen by RepairsUniverse.com'
The advice from the experts is highly anticipated!!
Regards,
Eduard Tieseler
Click to expand...
Click to collapse
Check out my thread: http://forum.xda-developers.com/showthread.php?t=2189789
I did it not long ago, and was fine. However, I opted to go for the digitizer + LCD assembly, as I didn't want to have to worry about separating the digitizer from the LCD and worrying about dust.
To answer your questions:
1) It's eaiser, takes less time, and you don't have to worry about dust with replacing the digitizer + LCD assembly.
2) Replace the adhesive. I tried reusing it... and it has some flex on it. So I got some new adhesive, scraped the old stuff off, put the new one, and used a heatgun to move the screen assembly around to get it to fit right, and then pressed it down as it cooled to secure it better.
3) Ebay
4) Not sure on this one... not that I know of anyway.
5) If you get the parts from eBay, then they sometimes come with tools (Torx, philips, and a plastic separator tool).
I also linked the video that I used in my thread, so you can look at that. It's pretty straightforward and easy to do. Took me about 45 minutes to just over an hour to do everything, as I was taking my time.
Well I did this process two days ago and for the most part it went well, but not without its issues.
First off, I should have heeded the advice of others suggesting to get the LCD + Digitizer pre-assembled. I tried to save some money however now there is a dead spot on my phone and I will have to spend that extra money to buy the kit anyways. So for anyone else thinking they can get away with just the digitizer, unless you have dustless neoprene gloves and a clean room (or possibly nitrogen or canned air) and lots of experience, do not attempt to replace one or the other, just get the pre-assembled kit.
I am going to replace it again with the kit in a few more days.
The only thing that came up that I didn't see anywhere else, was when I was pulling the back cover off. The spot where the camera is located was kind of sticking to the back cover. If I would have pulled to quickly or was too rough I would have easily damaged the camera. So my advice would be to work slowly when pulling the back cover off. If it feels like its resisting, it could be your camera. Wiggle it slightly and don't force it. The camera will loosen itself from the back case, but using too much force you could damage it.
Thanks for the info guys! :good:
etieseler said:
Well I did this process two days ago and for the most part it went well, but not without its issues.
First off, I should have heeded the advice of others suggesting to get the LCD + Digitizer pre-assembled. I tried to save some money however now there is a dead spot on my phone and I will have to spend that extra money to buy the kit anyways. So for anyone else thinking they can get away with just the digitizer, unless you have dustless neoprene gloves and a clean room (or possibly nitrogen or canned air) and lots of experience, do not attempt to replace one or the other, just get the pre-assembled kit.
I am going to replace it again with the kit in a few more days.
The only thing that came up that I didn't see anywhere else, was when I was pulling the back cover off. The spot where the camera is located was kind of sticking to the back cover. If I would have pulled to quickly or was too rough I would have easily damaged the camera. So my advice would be to work slowly when pulling the back cover off. If it feels like its resisting, it could be your camera. Wiggle it slightly and don't force it. The camera will loosen itself from the back case, but using too much force you could damage it.
Thanks for the info guys! :good:
Click to expand...
Click to collapse
I also purchased the full assembly and was able to switch the new parts onto my Rezound. Unfortunately, the earpiece (the part you listen to when NOT on speakerphone) and the proximity sensor did not work with the new set, and I am swapping it for a replacement. However, I've been inside the unit now 5 times, and I suggest in addition to the tools supplied with the sets (t5, small phillips and separator) you also have a small flathead (helps with starting the split the unit apart and also with pulling and reattaching the vibrator motor) and a long tweezers (invaluable when trying to reconnect the ribbon cables.)
Also, reconnect the MIDDLE ribbon cable (which is slightly twisted and longer) first, then reconnect the top, and don't forget to reapply the insulating tape (been there, done that).
Watch the take apart video on Youtube repeatedly until you can do it with your eyes closed, and be careful, the red plastic does break easily, especially on the corners.
Replaced my digitizer with good success, using new adhesive. Upon first re-assembly the digitizer was popping out of the plastic bezel a bit, but everything worked great, touch, display, everything. So I decided to take apart, add some more adhesive strips. Now the digitizer stays flush.
First boot after 2nd re-assembly, got boot with first vibrate, but no screen on. So I pull the battery to attempt again. Now I receive no vibrate response from power button. When plug into charger, orange light comes on for 5 seconds and then off indefinitely. This happens each time after battery pull+wall charger plugin.
I have tried multiple times disassembling, checking both ribbon cables that plugin to motherboard, appear to connect fine. Visually all other aspects of MB appear fine.
Any ideas anyone? Not sure what may have broke. I should have left well-enough alone, but the digitizer was somewhat spongey to touch on right side of screen and I could see white light shine up... TIA
Each time I pull the batt the orange light will come on solid for 5 or so sec, then off for good. One time even started flashing for a bit like it was charging from full depletion (like it does before it lets you power on). Not sure how to diagnose.
Did you make sure to put the yellow protective tape over the ribbon cable connections? When you open it (like a book) and see two ribbon cables. There originally was a small piece of tape over the connection to provide protection from anything being shorted out. Make sure this is back on.
If you no longer have the tape, I think any non-conductive tape would work like plain Scotch tape. Please correct me if I am wrong in that statement.
Sent from my Infected HTC Rezound using xda app-developers app
etieseler said:
Did you make sure to put the yellow protective tape over the ribbon cable connections? When you open it (like a book) and see two ribbon cables. There originally was a small piece of tape over the connection to provide protection from anything being shorted out. Make sure this is back on.
If you no longer have the tape, I think any non-conductive tape would work like plain Scotch tape. Please correct me if I am wrong in that statement.
Sent from my Infected HTC Rezound using xda app-developers app
Click to expand...
Click to collapse
I did not put those pieces of tape back on. In the YouTube video by "injured gadgets," I don't believe they re-covered up those ribbon cable plugins, so I also did not during re-assembly. Should I try that? Or, I assume, my board somewhere has gone bad? (Phone did work just fine after re-assemble, until I decided to take apart again)
And after doing this a handful of times, I figured out that the "earpiece" doesn't come with the digitizer/LCD/housing. It has to be pulled from the old phone and moved to the new one. Once I did that, everything was fine.
hgoldner said:
And after doing this a handful of times, I figured out that the "earpiece" doesn't come with the digitizer/LCD/housing. It has to be pulled from the old phone and moved to the new one. Once I did that, everything was fine.
Click to expand...
Click to collapse
hgoldner, when you had forgotten to re-apply the insulating tape over the ribbon cables, did that result in a toasted motherboard? I'm trying to find out if that's what happened to mine? Thx
red3razor said:
hgoldner, when you had forgotten to re-apply the insulating tape over the ribbon cables, did that result in a toasted motherboard? I'm trying to find out if that's what happened to mine? Thx
Click to expand...
Click to collapse
I would go ahead and try putting it back on. There was an earlier post where someone mentioned it was important to put it back on, perhaps he can comment on what can happen if its not on (He said he learned from experience). Perhaps you can PM him.
To be honest, I originally only put the tape back on one connection, but after the second time replacing both the LCD screen and the digitizer, I found the second piece of tape and now both are back on.
What can it hurt to see if that will fix it? Its fairly easy to get to on these phones.
Ed
Yes I did try put back on, no worky still. I assume motherboard issues now. So now I ask if anyone that has also failed to put tape insulation back on, has also resulted in motherboard fail?
red3razor said:
Yes I did try put back on, no worky still. I assume motherboard issues now. So now I ask if anyone that has also failed to put tape insulation back on, has also resulted in motherboard fail?
Click to expand...
Click to collapse
I ran it for about a week or so without the insulating tape. I assume you just mean the translucent, amber tape that goes over the jaw connectors of the ribbon cables on the motherboard? Not putting that on shouldn't have damaged your board... it's really just there to keep the jaw connectors from opening from vibrations.
carngeX said:
I ran it for about a week or so without the insulating tape. I assume you just mean the translucent, amber tape that goes over the jaw connectors of the ribbon cables on the motherboard? Not putting that on shouldn't have damaged your board... it's really just there to keep the jaw connectors from opening from vibrations.
Click to expand...
Click to collapse
I left it off on one connection for about a week also with no issues. However I did notice roughly a 16th of an inch of copper exposed on the ribbon. I can envision potential issues from that. I'm not sure about your phone, but the jaw connectors on mine would never open on their own. Far too much resistance to open from any vibration or movement. The vibrator motor connection had a better chance of disconnecting on its own than the ribbon cables. I'm sure that tape provides more than just locking the jaw connectors closed. I could be wrong though.
red3razor said:
hgoldner, when you had forgotten to re-apply the insulating tape over the ribbon cables, did that result in a toasted motherboard? I'm trying to find out if that's what happened to mine? Thx
Click to expand...
Click to collapse
No, I remembered and put it on before I powered up.
Dumped down the innertubes from my Asus Transformer TF300T
Just replaced my digitizer two days ago and I must add the difference is like night and day. I noted in a post that I had tripped and fell on it with my knee...lol ..nope.. I threw the damn thing and it hit the wall. Yahhh.. I know stupid lol... Something really pi$$ed me off tho and I kinda lost it.. .poooof....... Anyway, I had about 30 cracks in my digitizer and amazingly it still worked. Replaced it two days ago and it works great.
That factory adhesive is some SERIOUS stuff. I have performed many electronics repairs over the years and this...well...removing the digitizer and applying the new strips in exactly the right size was a royal pain in the a**! You REALLY gotta get that digitizer glass HOT if you want to be able to loosen it. Light heating WONT do squat to it. And the new strips arent even half as strong as the factory stuff. You really need patience and precision here.
Yes, dust ISVan issue where I live. Canned air came VERY useful. Also its good to have isopropyl alcohol and soft paper towels so you can clean any smudges you make on the LCD before reapplying the digitizer glass. Basically it's best to blow air over it quickly as you press the digi down to the adhesive. That makes sure every bit of contaminant is out.
About the ribbon cables, no I didn't reapply the amber tape to the jawbone connectors. Much of their adhesiveness was lost when I pulled them off. And as long as the ribbon cables are seated in properly and the jawbone connectors are securely locked down, they wont come disconnected. The tape is only there as an additional measure to secure the jawbone connectors from unlocking. Unless you drop your phone on concrete a lot, those cables arent coming loose....even then, dropping it wouldnt knock those loose.. Its more secure than you think. As far as the phone NOT working, the orange tape would have NO effect on that. Maybe one of your cables were partially disconnected and shorted out something on the mainboard. Either that, or it is static sensitive. Its possible if anything is CMOS.
ONLY issue I have since the repair is the top of the digitizer keeps pushing up because of the digitizer ribbon cable and where you have to bend and fold it in that groove to guide it behind the LCD . The ribbon isnt pinching down well and acts as a spring on the digitizer glass....adhesive not doing anything for that.
oh, did you all remove and reapply the clear (4 button tabs) at the bottom to the new glass? got mine in (the lights are pink now ...weeee ) Had to use some Gorilla super glue to restick them. That adhesive at the bottom was super strong and somehow they lost their stickiness when I pulled them off.
Digitizer after I finally got it unstuck from the LCD... wheewww damn. Lots of cracks. Thats what happens when the phone face eats the wall.....
So, my 4 soft keys on the bottom have yet out. Would fixing the digitzer get them back to working? My screens just got cracked like 2 days ago too, and I just want to make sure before i do all this and then find out i gotta take it all apart again. Thanks in Advance!

Extended Battery Mod - P769 - with case

This is an extended battery mod using two OEM batteries for the LG Optimus L9 P769. I am currently running AntonX's version of CM 10.2, which is OC'd to 1350 and UC'd to 200. Love his rom.
Credits to:
fastwanabe - http://forum.xda-developers.com/showthread.php?t=2397045
s0me guy - http://forum.xda-developers.com/showthread.php?t=1800177&highlight=battery+mod
Do this mod at your own risk! Soldering together lithium-ion batteries can be dangerous especially if you short them out. Those without soldering skills probably shouldn't do this! This can also destroy your phone!
The case I used was a pandmimi ULAK case - http://www.amazon.com/gp/product/B00DQ2DI44/ref=oh_details_o05_s00_i00?ie=UTF8&psc=1
I also suggest getting another wall charger with a higher amperage output. The stock charger might not work anymore. Something around 1.5 amps would probably do fine.
Suggested tools and parts:
- two new OEM BL-53qh batteries
- Soldering Equipment (Iron, Desoldering Braid, Solder, tip cleaner, etc)
- Wire to solder batteries together
- Small rotary cutting tool such as a dremel to cut case and back plate
- Razor knife to cut rubber sleeve
- Liquid Electrical Tape to cover exposed terminals
- Tape to hold batteries together
- Volt meter with a continuity or resistance function to test for shorts
- Double sided tape or tape roller up into a cylinder
- Pencil or marker
Step One- Gather materials and prepare a clean working area so you have ample room
Step Two- Charge both NEW batteries fully so their voltages are about the same.
Step Three - Place one battery in phone and put rolled up tape or double sided tape between back case and battery close it tight
Step Four - Remove back case so the battery comes out with it mark it with a pencil or marker
Step Five - Cut out back piece with razor knife or rotary cutting tool be careful not to break the back case. Keep the thin plastic we will use that later
Step Six - place the rubber piece on with nothing else and cut out the hole by pressing on it to mark the battery compartment and cut the rubber with the razor knife.
Step Seven - Tape both batteries together and place them in the phone put on the back case and the rubber. Place double sided tape on battery then line up the hard ULAK case with the rubber. Once alligned press them firmly together and pull the hard ULAK case off with the battery still attached. Mark where the batteries are with something. Remove the batteries and use the rotary cutting tool to cut the square battery hole out.
Step Eight - Clean up all the holes so that each piece can be removed without interfering with the batteries.
Step Nine- Use the liquid tape on the P769 back cover where the copper might be exposed
Step Ten - Solder positive to positive then check for shorts if there are no shorts solder negative to negative and check for shorts. if there are no shorts and the connections are good and sturdy then all the soldering is done. Make sure that the wire doesn't stick out to far from the battery because it might not fit in the battery compartment. To make things easier I burnt away the little bit of plastic that sticks up between the solder bridge and it is also a good idea to tin the connections and the wire before soldering them together.
Step Eleven - Once all the soldering is done and you are certain there are no shorts and your connections are good. connect the battery to the phone and try to turn it on. It should boot up with around 100% battery life during the first hour of use make sure to feel for battery warmth. If it starts to get really hot. It's probably messed up and you should fix it. Once all the checks are done and the battery fits in the phone fine use fast discharge and turn it on select everything if you want. Run it for about 5 or 10 minutes. if the battery gets warm but the temperature monitor doesn't move than your solder bridges are too tall making the other two connections not to touch the pins inside the battery compartment. After that is done and working use the liquid tape to cover the exposed connections that don't go inside your phone.
Step Twelve - Put the all the case pieces back on. Take the piece that you cut off the P769 back case and place it ontop of the battery use tape to tape it on. Then put on any decorative tape to cover the ugly hole. Take off the ULAK hard plastic case and put tape on the other side to prevent it slightly sticking to the battery. Then you can put it back together and enjoy you're long battery life.
Step Thirteen - Calibrate your phones battery http://forum.xda-developers.com/showthread.php?t=2192948
That's it. If anyone reads through it and doesn't understand or think I may have went too in depth they are welcomed to correct me. I hope you enjoy the mod whether you try or not that's up to you.
That is absolutely sick. Father was showing me how to solder awhile back, maybe I'll get around to this
Yeah it's a pretty good mod. I love absolutely love it. feels good in my hand, it isn't heavy. it really isn't hard to do as long as you have the tools and take your time. I love it. idt i've had my phone die in one day since I have did the double battery mod. it's quite spectacular. I suppose I have the extra battery life because it's a bit undervolted by AntonX's CM 11.

Categories

Resources