msm7227 chineese model root - Android Q&A, Help & Troubleshooting

Hi Everyone,
I know there are stupid people out there like myself that bought a crapy chineese tablet with model msm7227 shown that would like to know how to root the phone. Installing the Gingerbreak apk file and running it seems to do the trick.
I tried to take it a step further and upgrade the android version from 2.2.2 to 2.3.3 following instructions from a russian site that I translated.
Russian site link:
ublaze.ru/forum/ftopic1158.html
I translated the instructions in the website below. Refer to pdf attachment for instruction and pics:
Unfortunately I only managed to go as far as Step 3 G. Click Start to update ARM9.
Your tablet will automatically reboot after the upgrade.
For me after I click start the status changes indicating that it is Changing the Phone to Download Mode
It then switches off the unit and loses the com connection to the phone and the status changes to "Attempting to run Flash Programmer"
It fails then with the status "Software Download Aborted" Error "Could Not Communicate with Flash Programmer". I try an restablish the connection during the status "Attempting to run Flash Programmer" but it makes no difference.
So I have pretty much left it there. If any one else is game to give it a go and have better luck good luck. My unit still works after I reset it but its still on Android 2.2.2.
INSTRUCTIONS
Характеристики QUALCOMM MSM7227 FFA 3g
Код: Выделить всё
QUALCOMM MSM7227-1 Tablet PC with Mobile Phone function
Android 2.3 OS
512MB RAM +4GB Flash Memory
7 inch capacitive multi-touch screen
Built in 3G module and WiFi and bluetoothBuilt in GPS navigation
Built in 2.0MP/0.3 CMOS dual cameras
Support phone call and flash10.1 playing
ID устройства:
USB\Vid_05c6&Pid_9018&Rev_0226&MI_00
USB\Vid_05c6&Pid_9018&Rev_0226&MI_01
USB\Vid_05c6&Pid_9018&Rev_0226&MI_02
The firmware consists of 4 steps.
Step 1. Zhelateono have a PC running Windows XP, but I probyval and Windows 7 32-bit also works.
Step 2. Installing the USB driver
рис. 1
If the popup window does not appear automatically, go to the Device Manager> Other Devices
and click the right mouse button on the label Qualcomm HSUSB Device and select> Update Driver
pointing the way to the drivers for each Qualcomm HSUSB Device (see Fig. 2) as follows (see Fig. 1)
рис. 2
Step 3. update ARM9
A. Turn the tablet and connect it to your computer.
B. Go to Device Manager and check that, if the operating system your computer has defined the tablet (see Figure 3.)
рис. 3
C. Installing the program QPST.
рис. 4
D. Click Start, and then click the QPST Configuration. Add all the ports that are able to find (see Fig. 5)
рис. 5
Navigate to the Software Download tab and remove the check mark from C Auto Backup/Restore
рис. 6
рис. 7
Click Start clients and select Software Download, and then click Multi-image.
Click Browse and specify the correct path to the image (image).
Код: Выделить всё
...\Reflash Software\ARM9\image
Click Advanced, select the AMSS Apps Boot Ldr Hearder and AMMS Apps Boot Loader, then click OK
рис. 8
The tab Multi-image, uncheck Auto Backup / Restore
рис. 9
G. Click Start to update ARM9.
Your tablet will automatically reboot after the upgrade.
Step 4. update ARM11
A. Make sure your tablet is connected to your computer via USB-cable.
B. Open ... \ Reflash Software \ Android_Download_tools \ Arm11 V1.7_20110418 \ Android_download.exe
C. Click Connect and verify that the displayed fastboot device
D. Press the volume (Volume) and the power button, and then click the Reset button (Reset)
E. Hold down the volume (Volume) and the (what exactly, the instructions are not written - most likely the trigger) and then, in the program, click Connect again.
And then start flashing.
F. Click Run and wait for as long as see the word Done!!!
рис. 10
G. In this update is completed.
Note. If your tablet does not flash, as I have, in some cases, do the following:
1. Take the sd card and dump the sd card to the root of the archive here: update.zip
2. Insert the sd card into the tablet.
3. Hold the power button and press vol -.
4. Without releasing the two buttons we press on reset clip (located just below the buttons vol -)
Next tablet should enter into recovery mode, that's how it looks:
5. Next, we need to press the Home button (Home)
6. C Use the "vol +" and "Vol -" go to the inscription:
code: Выделить всё
apply sdcard:update.zip
and press the touch button with the four squares (just below the button home)
7. Upgrade process will start. At the end of reset the unit.
Download the firmware for Ipad QUALCOMM MSM7227 FFA 3g
Скачать прошивку для Ipad QUALCOMM MSM7227 FFA 3g

Use this tool to root it : http://www.only4download.com/2012/05/download-superoneclick-android-software.html
Don't forget the THANKS button

You Biscuit!!!!
Thanks guys for helping me to flash my device!!! Running 2.3 with full marketplace. WOO HOO!!!
Ok I had managed to root it before finding your post. ( I think it was UnversalAndroot if memory serves me right - tried so many! )
Used Chrome to translate the original Russian page to English. The USB drivers and the quickboot drivers are all in the file listed on that site. (2.3 software ) I used a Windows XP workstation to connect the device and load the drivers.
To get the device into fastboot:
turn on while holding the Volume UP + button. You should see the android robot.
Connect to PC and install the ADB driver.
Run the Android_download.exe and let it do it's magic. The device will reboot twice and will show a new logo on rebooting. ( at this point I installed the standard USB drivers )
The device will default to Chinese language. Find the settings icon ( blue rings on black ) and look for the icon with an "A" on it.
The network does not work - I assume its because of my region ( South Africa GSM 900 / 1800 / 2100 ) and something is missing in the drivers. It no longer detects a SIM or network.
At least I have a device that resembles a proper Android device now! Time will tell if it's any more stable than the brickware it came with.
Please don't ask me too many technical questions - I'm not a pro by any means!
Thanks

Finally
Finally found the time to get around to trying the flashing to Android 2.3.3 again.
It all worked great this time round. The issue I was having with installing the ARM 9 update was that everytime it changed the unit to download mode and rebooted it, the COM port would change and lose connecitvity after the reboot. But once I used the browse button in the QPST Configuration application and changed the port to match the new port allocated after the reboot it successfuly transfered the software across without the error.
Its so great now that the unit has Android 2.3.3 as now all the following things have been fixed and verified working
1) 3G data works properly now with Telstra
2) Phone and messaging works with Telsta
3) I dont get face book error in the news read section
Theres still a few android apps that are not compatible with the device like, Adobe Flash player but there are suitable alternatives.
But now its a nice workable unit. Very Happy :>

Some error has been solved
saintlypaul said:
Finally found the time to get around to trying the flashing to Android 2.3.3 again.
It all worked great this time round. The issue I was having with installing the ARM 9 update was that everytime it changed the unit to download mode and rebooted it, the COM port would change and lose connecitvity after the reboot. But once I used the browse button in the QPST Configuration application and changed the port to match the new port allocated after the reboot it successfuly transfered the software across without the error.
Its so great now that the unit has Android 2.3.3 as now all the following things have been fixed and verified working
1) 3G data works properly now with Telstra
2) Phone and messaging works with Telsta
3) I dont get face book error in the news read section
Theres still a few android apps that are not compatible with the device like, Adobe Flash player but there are suitable alternatives.
But now its a nice workable unit. Very Happy :>
Click to expand...
Click to collapse
I have solved some error when update rom for it. I attached it from file word

HELP ERROR update ARM9
Hi, I have a problem when star the process appear in red NAK: Invalid Address
I have read the manual 6 times and nothing, please how I can fix this error

Same Error
Hi
I am getting the same error as yours.
Where you able to move ahead an upgrade the tablet to 2.3 ?

Related

[Q] Odys Genesis bricked after cyanogenMod7 custom rom for odys genesis update?

Hello,
I've tried updating the Odys Genesis to the custom firmware cyanogenMod7 custom rom for odys genesis.
I think i did it the wrong way. I've searched for hours on the internet how to do it, and then i cam across a post that said i just needed to put it on the device and then android would pop up and say: "A new update is available" and i just would have to tap that. So, i did.
The device rebooted and started updating all kinds of stuff in a dos-like enviroment. But now it's only a black screen and saying ANDROID in white letters. I've kept it like that for an hour, and then i tried resetting it (behind the device, hard reset button). I see the Odys brand screen, but then it's back at the black screen with android on it again.
Is there any hope left? Can i do something to fix it?
I've tried searching for hours on the internet, and i came up with absolutly nothing. Any help would be greatly appreciated!
Thanks in advance!
I found out a little bit more:
- My problem is called a boot-loop. It seems like it anyway, i only see a tiny white text saying 'android'.
- I can't find anywhere on the internet if there's a recovery mode for the Odys Genesis.
- The device will turn on with any button-combination, except when i press menu+power or power+reset.
I have been looking at Odin, cause that should be a unbrick-program for android phones. But it seems you need specific firmware for your model. Can i just use the original firmware update from the website of the manufacturer?
Or am i just totally ****ed? Just a reaction alone would be appreciated !
Solution
And somebody can close this topic!
I'm extremely happy, cause by a little accident i discovered how i could flash back to the normal firmware.
For somebody who has the same problem, here my solution:
When the device is on the screen only saying android do the following:
- Press the hard reset button (on the back, the tiny hole) and the menu button at the same time.
- The android screen should now go away, and it should like the device is off (although it isn't).
- Plug in the usb cable and connect it to your pc.
- If you had your device previously plugged in to your pc before, the pc will falsly recognize it as 2 hdd's while there isn't any shown in this computer.
To fix that:
- Go to device manager (This computer (right click) -> properties -> device manager)
- Uninstall the falsly drivers, (so there is no driver anymore).
- Disconnect the usb cable and connect it again.
- Windows should now say (or say in device manager) that an unknown device is connected.
- Download the Pc Update Tool and original firmware from the manufacturer website: (can't post url's here, so google Odys Genesis and you will get there)
- At the driver installation window choose you would like to point where the drivers are.
- Choose the dir from the pc update tool, and choose the driver map according to your processor and windows.
- The device should now be installed as a RK2.... something device.
- Start the Pc Update Tool
- The first box below should be green, indicating it sees the device and is ready to flash.
- At the box image, choose the original image downloaded from Odys website.
- Click Upgrade.
All should work well now, the box (log) should keep you informed. It could take a little while.
When it's done, it will tell you in the window. The device should now restart and Boot recovery should start and the device, formatting everything, resetting again and then installing everything. It all could take some while, so be patient.
And that's it.... then everything is working again ! ~!
Please let me know where you downloaded the CM7 ROM from... can't get it from the link in other post
Thanks
sleuteltje said:
And somebody can close this topic!
I'm extremely happy, cause by a little accident i discovered how i could flash back to the normal firmware.
For somebody who has the same problem, here my solution:
When the device is on the screen only saying android do the following:
- Press the hard reset button (on the back, the tiny hole) and the menu button at the same time.
- The android screen should now go away, and it should like the device is off (although it isn't).
- Plug in the usb cable and connect it to your pc.
- If you had your device previously plugged in to your pc before, the pc will falsly recognize it as 2 hdd's while there isn't any shown in this computer.
To fix that:
- Go to device manager (This computer (right click) -> properties -> device manager)
- Uninstall the falsly drivers, (so there is no driver anymore).
- Disconnect the usb cable and connect it again.
- Windows should now say (or say in device manager) that an unknown device is connected.
- Download the Pc Update Tool and original firmware from the manufacturer website: (can't post url's here, so google Odys Genesis and you will get there)
- At the driver installation window choose you would like to point where the drivers are.
- Choose the dir from the pc update tool, and choose the driver map according to your processor and windows.
- The device should now be installed as a RK2.... something device.
- Start the Pc Update Tool
- The first box below should be green, indicating it sees the device and is ready to flash.
- At the box image, choose the original image downloaded from Odys website.
- Click Upgrade.
All should work well now, the box (log) should keep you informed. It could take a little while.
When it's done, it will tell you in the window. The device should now restart and Boot recovery should start and the device, formatting everything, resetting again and then installing everything. It all could take some while, so be patient.
And that's it.... then everything is working again ! ~!
Click to expand...
Click to collapse
I have the same issue, but I have a 64bit Win7 and it just won't work. Windows will not install the original drivers. Any other way to go around it?
I only need make a hard reset, any help??? I don't remember unlock code
I've tried to download original firmware but i can't find it.

Pantech Sky Vega a760s Soft Brick

my pantech sky vega a760s got soft bricked
here's what happened:
-the phone won't open unless connected to pc
-when connected, it will only go to charging mode
-when i try to enter recovery mode, this shows up:
"your phone will restart due to error occurred while running application "
i cannot access recovery mode, the only thing i can access is the s/w upgrade mode, which i don't know how to use since i'm not korean
and i can't understand pantech's website.
also, when i enter in fastboot mode, all drivers are installed except for a driver named "Android" which is too general for me to manual search (inlcuded an image attachment of the failed driver)
How can I unbrick my phone?
PLEASE HELP. THANK YOU IN ADVANCE.
same here..
same here my sky vega a760 stock on boot image anyone can help plsss how can i revive this..plsssss.
joekap said:
same here my sky vega a760 stock on boot image anyone can help plsss how can i revive this..plsssss.
Click to expand...
Click to collapse
You should re-install new room stook via home page iVeGa:good:
Re: Help..
tnx for the reply but how can i reinstall i dont know where to donwload and i cant understand in korean site.. plsss send me working rom for A760s plsss...tnx
[TUT]Recovery Mode Sky Vega Racer IM-A760S/A770K
joekap said:
tnx for the reply but how can i reinstall i dont know where to donwload and i cant understand in korean site.. plsss send me working rom for A760s plsss...tnx
Click to expand...
Click to collapse
To go into Soft/Ware download mode
1. Turn of phone
2. Simultaneously press: VOLUME UP + MENU + POWER
3. S/W Upgrading will now flash on the screen
To upgrade firmware back to version 1.47, you first need to have the UniUSBdriver installed on your computer.
4. After you have installed the driver, test your phone’s connection to the computer to initially determine all the required drivers were installed properly (this is while your phone is in S/W download mode). But before doing this, make sure that you have activated USB DEBUGGING on your phone.
Code:
>settings
>applications
>development
>usb debugging (must be checked)
5. Using Microsoft Internet Explorer v8 or v9, proceed to this page:
-------------->>> dmfile.isky.co.kr/NewSelfUpgrade/index.html?userid=&hpno
Notice when that page opens, it will prompt you to install ACTIVE X. Allow that installation to proceed.
6. After ACTIVE X has been installed, notice on the left side there is a something like loading prompt. Wait until it gets into blue bar with arrow up phrase noting USB with some Korean characters. Then boot to S/W mode your phone and plug it to your compurer then click the blue bar with arrow up.
7. Clicking the Blue bar with arrow up will turn it into a progressing bar. Notice the characters on top of the progress bar may change and at this point there is communication between the phone and the Sky download site. It may take a few minutes for the phone to establish a download connection between Sky’s services. Once a connection is established, the characters above the progress bar will turn into a progressing percentage bar starting from 1% and ending into 100%.
There will be two phases of the progressing percentage bar. The first phase is downloading the software while the second is loading the v1.47 software into the phone. After the 2nd phase, the phone will automatically reboot. The first phase will depend who slow or fast your internet connection is.
:fingers-crossed: Goodluck :fingers-crossed:
clearlangpo said:
To go into Soft/Ware download mode
1. Turn of phone
2. Simultaneously press: VOLUME UP + MENU + POWER
3. S/W Upgrading will now flash on the screen
To upgrade firmware back to version 1.47, you first need to have the UniUSBdriver installed on your computer.
4. After you have installed the driver, test your phone’s connection to the computer to initially determine all the required drivers were installed properly (this is while your phone is in S/W download mode). But before doing this, make sure that you have activated USB DEBUGGING on your phone.
Code:
>settings
>applications
>development
>usb debugging (must be checked)
5. Using Microsoft Internet Explorer v8 or v9, proceed to this page:
-------------->>> dmfile.isky.co.kr/NewSelfUpgrade/index.html?userid=&hpno
Notice when that page opens, it will prompt you to install ACTIVE X. Allow that installation to proceed.
6. After ACTIVE X has been installed, notice on the left side there is a something like loading prompt. Wait until it gets into blue bar with arrow up phrase noting USB with some Korean characters. Then boot to S/W mode your phone and plug it to your compurer then click the blue bar with arrow up.
7. Clicking the Blue bar with arrow up will turn it into a progressing bar. Notice the characters on top of the progress bar may change and at this point there is communication between the phone and the Sky download site. It may take a few minutes for the phone to establish a download connection between Sky’s services. Once a connection is established, the characters above the progress bar will turn into a progressing percentage bar starting from 1% and ending into 100%.
There will be two phases of the progressing percentage bar. The first phase is downloading the software while the second is loading the v1.47 software into the phone. After the 2nd phase, the phone will automatically reboot. The first phase will depend who slow or fast your internet connection is.
:fingers-crossed: Goodluck :fingers-crossed:
Click to expand...
Click to collapse
i need help. i just installed uniUSBdriver and it's successful. however, when i connect the phone there is one driver that is unable to install. the driver is just called "android" tried to look everywhere for a manual installer but the name of the driver is too vague to search. can you please help me with this one? it seems like the self upgrade site can't detect the phone without this driver installed.
Solution Soft brick, Android drivers in Fastboot
jimmygammi said:
i need help. i just installed uniUSBdriver and it's successful. however, when i connect the phone there is one driver that is unable to install. the driver is just called "android" tried to look everywhere for a manual installer but the name of the driver is too vague to search. can you please help me with this one? it seems like the self upgrade site can't detect the phone without this driver installed.
Click to expand...
Click to collapse
1. Connect your phone in Fastboot, and when your pc asks for 'Android' drivers, you need to install PDAnet, just google to download it.
2. then to Fastboot, and Install Recovery SWM v6 either normal or touch
3. Then go to Recovery and Install new stock/custom rom from SdCard.
thats all. :fingers-crossed:
bobby786pk said:
1. Connect your phone in Fastboot, and when your pc asks for 'Android' drivers, you need to install PDAnet, just google to download it.
2. then to Fastboot, and Install Recovery SWM v6 either normal or touch
3. Then go to Recovery and Install new stock/custom rom from SdCard.
thats all. :fingers-crossed:
Click to expand...
Click to collapse
can you post links where to get the recovery image and a link where to download roms? i'm trying to search but no luck. your help will be really appreciated. thank you very much :laugh:
stuck at s/w uploading
heeelp can anyone help me... my a760s dont turn on and if i plug a charger or into a pc the only thing that apears is "s/w uploading"
Did you fix it? results?
beakolang said:
heeelp can anyone help me... my a760s dont turn on and if i plug a charger or into a pc the only thing that apears is "s/w uploading"
Click to expand...
Click to collapse
Although its long enough for you to forget you once had Sky 760 but did you try the method posted by "clearlangpo"?
You phone reincarnated anyway?
clearlangpo said:
To go into Soft/Ware download mode
1. Turn of phone
2. Simultaneously press: VOLUME UP + MENU + POWER
3. S/W Upgrading will now flash on the screen
To upgrade firmware back to version 1.47, you first need to have the UniUSBdriver installed on your computer.
4. After you have installed the driver, test your phone’s connection to the computer to initially determine all the required drivers were installed properly (this is while your phone is in S/W download mode). But before doing this, make sure that you have activated USB DEBUGGING on your phone.
Code:
>settings
>applications
>development
>usb debugging (must be checked)
5. Using Microsoft Internet Explorer v8 or v9, proceed to this page:
-------------->>> dmfile.isky.co.kr/NewSelfUpgrade/index.html?userid=&hpno
Notice when that page opens, it will prompt you to install ACTIVE X. Allow that installation to proceed.
6. After ACTIVE X has been installed, notice on the left side there is a something like loading prompt. Wait until it gets into blue bar with arrow up phrase noting USB with some Korean characters. Then boot to S/W mode your phone and plug it to your compurer then click the blue bar with arrow up.
7. Clicking the Blue bar with arrow up will turn it into a progressing bar. Notice the characters on top of the progress bar may change and at this point there is communication between the phone and the Sky download site. It may take a few minutes for the phone to establish a download connection between Sky’s services. Once a connection is established, the characters above the progress bar will turn into a progressing percentage bar starting from 1% and ending into 100%.
There will be two phases of the progressing percentage bar. The first phase is downloading the software while the second is loading the v1.47 software into the phone. After the 2nd phase, the phone will automatically reboot. The first phase will depend who slow or fast your internet connection is.
:fingers-crossed: Goodluck :fingers-crossed:
Click to expand...
Click to collapse
Hello Hacker!
I am Zahid Gill and a software engineer by profession. Websites are my speciality. I love android and Korean phones. I have bricked/ unbricked fixed and patched many phone before (but only with XDA's help ) many
While flashing Sky vega 760s it stuck on some point. I waited long enough but thenI had to remove it and.... it was bricked.
I was still able to go to recovery, fastboot and bootloader. I tried wiping /system and others but cwm was not able to.
I tried flashing with offline flasher tool again but it went into red screen on bootloader, like here:
http://sphotos-g.ak.fbcdn.net/hphotos-ak-prn1/p206x206/26340_10200120329905648_1168156367_n.jpg
NOW, offline flashing stuck on 60%. I am unable to boot the phone in any other mode. Even putting on charging takes phone to this red s/w mode.
Are you able to help me with this? I shall be very thankful.
PS: I had stock ROM 4.1.2 originally updated with no custom tickling.
Did you find any solution
Hello I also stuck in same situation. My phone ima-760 got soft brick and red S/w upgrading only. Kindly help if any one has a solution.
Buddy
jimmygammi said:
my pantech sky vega a760s got soft bricked
here's what happened:
-the phone won't open unless connected to pc
-when connected, it will only go to charging mode
-when i try to enter recovery mode, this shows up:
"your phone will restart due to error occurred while running application "
i cannot access recovery mode, the only thing i can access is the s/w upgrade mode, which i don't know how to use since i'm not korean
and i can't understand pantech's website.
also, when i enter in fastboot mode, all drivers are installed except for a driver named "Android" which is too general for me to manual search (inlcuded an image attachment of the failed driver)
How can I unbrick my phone?
PLEASE HELP. THANK YOU IN ADVANCE.
Click to expand...
Click to collapse
I have the same problem but a lot of the answers are to re-install stock? Which part don't they understand...it's BRICKED ( and only shows the RED S/W Upgrading symbol) so it's impossible to Flash stock firmware in that state?

Rooting prestigio 5297c

Hi all.
I received my prestigio pmp 5297c with 4.2 preinstalled. I tried to find a way to root it but without any success.
Any idea would be valuable.
Thanks.
Sent from my PMP5297C_QUAD using xda app-developers app
Rooting problem PMP 5297C QUAD SOLVED
Hi,
I found a solution thanks to this web site:
http://androidforum.cz/viewtopic.php?f=815&t=48237
Translate it with google translate to english. I had some problems installing the right driver on my windows 7 x64 machine but I succeeded.
Basically it goes like this:
1. Download the zip from the link on the web page and unpack it.
2. Start the RKAndroidTool.exe (in the status bar it will say "No found RKAndroid rock usb")
3. Shut down your tablet and disconect the usb cable from the tablet that is connected to your pc.
4. Press the volume up button and hold it for 6 - 7 secconds.
5. Still holding the volume up button plug in the usb cable that is connected to You pc. (At this point in my case nothing happened)
6. (If nothing happens) Go to control panel - device manager and there You will see an unknown device.
7. Right click on the unknown device and select update driver. Point to the folder where You unpacked the downloaded zip / Drivers folder and select the search in subfolders checkbox. press OK button. Windows will install the drivers. After that if the tablet didn't start automatically boot it up by pressing the power button.
8. The RKAndroidTool.exe now will recognize the device.
9. Set the checkbox next to rom/recovery.img and press "RUN"
10. The tool will do what it has to do.
From here on just follow the instructions for rooting the tablet from the website.
Hope it will work for You as it worked for me.
Regards
Just use King root from Play Store

[Q] Help :Please: with Prestigio - PMP7280C3G V4.2.2 - ? -

Hello I got this tablet Prestigio - PMP7280C3G V4.2.2 back in November, December time and I am wanting to Root it.
From a post I did back then on another website a user replied that he got it working and rooted using a method on a website into which here's the Instructions translated into English below....
-
Testing the current model PMP7280C3G_DUO with FW 1.0.05 and 1.0.07
Installing CWM :
First Tablet Do NOT let it lie somewhere near you will need it .
Second Download and unzip the file . PMP7280C3G_QUAD-recovery-flash.zip | Ulo?.to password : 7280
3rd Open Device Manager on the computer to turn off the tablet and connect the cable to the PC for a while, the new device
( MT65xx preloader ) right click update driver (if 2x click left to open the info on the device and select Update Driver )
and manually install the driver " MediaTek preloader USB VCOM Port " from the Drivers folder depending on your version of
Windows (tested on XP and Win7 32bit and 64bit ) - If does not happen the first time you just disconnect and reconnect
tablet , again captured the moment on the device.
4th Unplug the tablet and start Flash_tool.exe
5th Right click on a scatter - loading and set the path to the directory / PMP7280C3G Recovery
CWM/MT6589_Android_scatter_emmc.txt and let Open.
6th Up in a menu icon you click on a download in the following confirm with YES you want to continue .
7th Connect the tablet off - starts by itself recovery download to your tablet . Can now be two situations ; endings Will
a download window with a green circle . A second variant or passes first the download and install the computer starts by
itself another driver " MediaTek DA USB VCOM Port" and flash program throws an error . Not to worry if you just unplug the
tablet itself on off it and click again to download again, click YES to connect off tablet . Ted would arrive melo
successful recovery in tablet and confirmation will be green ring in a new window.
8.Odpojte cable from the tablet and hold the VOL + and Power 3 seconds and you are in CWM recovery .
ROOT :
First In the ROOT folder is a file Supers - v1.65.zip and upload the memory card or tablet.
Second Run the recovery and select "install zip from sdcard" then select a location where you want the file to install
depends by location " choose zip from sdcard " and " choose zip from internal sdcard " you will find include file and
press power.
3rd select reboot system
That's all .
Way back in the state with Origami recovery without root if required :
Approach, as well as with CWM just place ingredients into CWM Recovery Route to Recovery folder Origo . The rest is the
same. In the tablet to run the application supers and remove root data settings .
THNX :
XDA for Supers - v1.65.zip
-
-
-
Now from the above I have downloaded the files Turned off the Tablet gone into device manager and plugged in the cable from the Tablet to the USB-Port of my laptop. It says in the steps above in step 3 that a new device ( MT65xx preloader ) should show up but it doesn't not in device manager not even on my computer now is that because the tablet is turned off also when its off and plugged in it's just charging.
Also when I got this Tablet I already hooked it up to my laptop to put music onto the tablet and photos so does that mean I need to turn the tablet on and uninstall anything that is to do with the Tablet in device manager then go from step 3 again - Does anyone know if that sounds about right since the new device ( MT65xx preloader ) in device manager doesn't show up yet with it's turned off and plugged in.
Any help will be Massively Appreciated.

HOW TO FIX FLASH TOOLS ERROR S_BROM_DOWNLOAD_DA_FAIL (0x7D4) & 2004) FOR MTK PHONES

HOW TO FIX FLASH TOOLS ERROR S_BROM_DOWNLOAD_DA_FAIL (0x7D4) & 2004) FOR MTK PHONES
FIX FOR SP FLASH TOOLS ERROR S_BROM_DOWNLOAD_DA_FAIL (0x7D4) AND (2004)
Follow the following steps:
1. Get SP flash tools (Latest version)
2. Download your phone's firmware (from manufacturer site or needrom.com etc) and extract it.
3. install Mediatek Preloader drivers as per your OS version (win x7 , 8 10 etc) and architecture (32/64bit).
4. Run Flash tools with admin as administrator
5. select the scatter file from the firmware folder you downloaded and wait for it to load. (Do not connect your phone yet and leave the battery inserted)
6. Select Download Only
7. Hit the download button
8. Now plug in the micro/type C usb end of your cable to your phone but dont plug to PC. yet
9. While hold down both volume buttons i.e up and down buttons, (Do not press the power button), Insert the Usb cable end to your PCs usb port (Please choose a port thats very reliable).
10. After a while, P Flash tool will begin to upgrade your phone, dont release the buttons yet, let it lapse about 2mins then release them, the firmware upgrade will still continue and it will display a tick pop-up when done (this may take between 5-10mins).
Now unplug your phone, remove and re-insert the battery and power-up your phone. You phone is now unbricked.
Note that the first boot will longer than a regular boot.
This saved me
Oh my god. I was searching for hours and hours for a solution. This post saved my back side.
Perfect Solution for ZTE Blade A520
Thank you very much. This worked like a charm. Very helpful
adisa said:
FIX FOR SP FLASH TOOLS ERROR S_BROM_DOWNLOAD_DA_FAIL (0x7D4) AND (2004)
Follow the following steps:
1. Get SP flash tools (Latest version)
2. Download your phone's firmware (from manufacturer site or needrom.com etc) and extract it.
3. install Mediatek Preloader drivers as per your OS version (win x7 , 8 10 etc) and architecture (32/64bit).
4. Run Flash tools with admin as administrator
5. select the scatter file from the firmware folder you downloaded and wait for it to load. (Do not connect your phone yet and leave the battery inserted)
6. Select Download Only
7. Hit the download button
8. Now plug in the micro/type C usb end of your cable to your phone but dont plug to PC. yet
9. While hold down both volume buttons i.e up and down buttons, (Do not press the power button), Insert the Usb cable end to your PCs usb port (Please choose a port thats very reliable).
10. After a while, P Flash tool will begin to upgrade your phone, dont release the buttons yet, let it lapse about 2mins then release them, the firmware upgrade will still continue and it will display a tick pop-up when done (this may take between 5-10mins).
Now unplug your phone, remove and re-insert the battery and power-up your phone. You phone is now unbricked.
Note that the first boot will longer than a regular boot.
Click to expand...
Click to collapse
Thank you very much Sir, you are awesome!
Thank you very much Sir, you are awesome! I have made my dead phone alive following your post. You are the Life Saver of my phone. I have no word to thank you. I salute your hard work. Thank you very much. I want to share your post to everyone who are seeking solution like me.
mohidulhaq said:
Thank you very much Sir, you are awesome! I have made my dead phone alive following your post. You are the Life Saver of my phone. I have no word to thank you. I salute your hard work. Thank you very much. I want to share your post to everyone who are seeking solution like me.
Click to expand...
Click to collapse
New Error Now-
Error : S_AUTH_HANDLE_IS_NOT_READY(5000)
i have this error "Failed to Connect DA: S_AUTH_HANDLE_IS_NOT_READY". i dont know how i do
Ndanou jean-claude said:
i have this error "Failed to Connect DA: S_AUTH_HANDLE_IS_NOT_READY". i dont know how i do
Click to expand...
Click to collapse
Hi!
You should watch this video and tutorial, it was helpful for me too.
https://www.getdroidtips.com/bypass-mediateks-sp-flash-tool-authentication-protection/

Categories

Resources