While updating a new Xperia U to ICS the PCC had an error while flashing the new firmware. Now the screen lights up, the sony logo is shown for ~3-5 seconds and then it reboots.
After that I have been unable to get it recognized again by either PCC/SUS or flash tool.
I also checked my log files in Linux and no device appears.
I've tried 3 different machines (2x Windows 8, 1x Win 7), multiple USB ports. Also leaving the battery out for ~30 mins didn't change the behavior.
The green light for download mode comes on, but after about 5 seconds the light goes out and it goes into the boot loop again.
So by now I believe the device needs to be sent in, but maybe some one has a few more things I can try.
Try pressing the volume down plus volume up plus power button all 3 simultaneously till u feel 3 vibrations
Sent from my ST25i using Tapatalk 2
Can you make sure the Flashtool drivers are installed ? Go to Flashtool Directory, open drivers directory and start the setup.. Make sure to select the Flashmode and Fastboot drivers are also selected. Then, reboot System and folow this order.
Startt flashtool,select f/w, wait for Flashtool to tell you to connect to device. Then, holding the Volume down button (while phone is switched off), plug the cable into phone (The usb cable must already be connected to PC before starting the Flash Procedure )
The Order is very important.. I had same issue with U (althoguh mine crashed with Flashtool and same as what you observed. When I followed this order, I was able to get it detected and flashed )
Hopefully, you wont need to return to Service Center
let me know how it goes
Cheers ! & Merry Christmas
And yes I forgot to mention
Wrong section
Plz use question n answer section next tym
Sent from my ST25i using Tapatalk 2
drsanket_xperia_u said:
Try pressing the volume down plus volume up plus power button all 3 simultaneously till u feel 3 vibrations
Sent from my ST25i using Tapatalk 2
Click to expand...
Click to collapse
No response, I've tried holding all three buttons for a minute, but it doesn't vibrate after turning on. The only way I can turn it off is by removing the battery.
Min3r said:
Can you make sure the Flashtool drivers are installed ? Go to Flashtool Directory, open drivers directory and start the setup.. Make sure to select the Flashmode and Fastboot drivers are also selected. Then, reboot System and folow this order.
Startt flashtool,select f/w, wait for Flashtool to tell you to connect to device. Then, holding the Volume down button (while phone is switched off), plug the cable into phone (The usb cable must already be connected to PC before starting the Flash Procedure )
The Order is very important.. I had same issue with U (althoguh mine crashed with Flashtool and same as what you observed. When I followed this order, I was able to get it detected and flashed )
Hopefully, you wont need to return to Service Center
let me know how it goes
Cheers ! & Merry Christmas
Click to expand...
Click to collapse
I tried that right now, Flashmode and Fastboot drivers are installed. Flash tool is ready, device is plugged in with volume down pressed, green light comes on. Nothing is found on the PC, after about 5 seconds the green light turns off and the phone shows the sony logo. Green light also comes on if i simply plug in the usb without volume down pressed. So I'm thinking, the download mode has some how been corrupted?
drsanket_xperia_u said:
And yes I forgot to mention
Wrong section
Plz use question n answer section next tym
Sent from my ST25i using Tapatalk 2
Click to expand...
Click to collapse
Sorry about that, maybe a moderator can move my topic to the right section.
Are u connecting it properly???
Make sure when u connect ur cell to ur pc u have nt presed the power key
keep the phone off
Press the volume down button ( keep it pressed, dun
leave it) and connect it to the usb
U will see green light
Darn.. That looks bad.. That did it for me on every occasion. I think you might have a hardbrick due to the interrupted write cycle so I dont think any other way except to take it to Service Center
Sorry I couldnt help
drsanket_xperia_u said:
Are u connecting it properly???
Make sure when u connect ur cell to ur pc u have nt presed the power key
keep the phone off
Press the volume down button ( keep it pressed, dun
leave it) and connect it to the usb
U will see green light
Click to expand...
Click to collapse
Exactly what I'm doing and the green light does come on. Except it decides to go into a boot loop after it apperantly boots into download mode but doesn't stay there.
Min3r said:
Darn.. That looks bad.. That did it for me on every occasion. I think you might have a hardbrick due to the interrupted write cycle so I dont think any other way except to take it to Service Center
Sorry I couldnt help
Click to expand...
Click to collapse
That's what I've been fearing. In which case it goes back to the seller in the hope that he will send me a new device.
Moved
Is there any chance of properly reactivating flashmode by using a JTAG?
Cebalrai said:
Is there any chance of properly reactivating flashmode by using a JTAG?
Click to expand...
Click to collapse
Risky business
Jtag. ...used for hard bricked devices n. Seen max to work wid samsung phones only....
Wont recommend u too open up ur xu
Let the service center try first
Sent from my GT-N7000 using Tapatalk 2
Have you manage to recover your phone without taking it to service?
I'm in the exactly same situation... Any help is welcome...
While trying to enter flashmode, green light turns on but after some secs it turns off and sony logo appears on screen. any chance to recover this beautiful brick ?
thanks
After several tries (a lot of...) I manage to enter flashmode and SUS is now reinstalling sony ROM.
Honestly I don´t know how it works this time and not the others but i'm happy with it independently of what happens.
... seems flashtool is detecting ur phone try to flash first the stock kernel and do not wipe everything it shud be in timing though.. onces it is flash charge ur phone in kernel mode (phone is off) then you can flash the stock fw of ur XU.
I bricked my phone
I bricked my xperia U as well... When i tried to power ON, it just vibrates and nothing happens, i dont even get the sony logo. When i get into flash boot mode it gets connected but after 20secs, the phone turns off again. Only fastboot mode stays on. How can i unbrick my phone??? Plz help. I made a mistake by flashing the custom jelly bean rom without flashing the kernel first.
adithyasailesh said:
I bricked my xperia U as well... When i tried to power ON, it just vibrates and nothing happens, i dont even get the sony logo. When i get into flash boot mode it gets connected but after 20secs, the phone turns off again. Only fastboot mode stays on. How can i unbrick my phone??? Plz help. I made a mistake by flashing the custom jelly bean rom without flashing the kernel first.
Click to expand...
Click to collapse
No worries. The phone turns off because it doesn't receive any signal from the PC - many people make the mistake of connecting the device in flashmode first, and then they start the flashtool etc.
Instead, load the flashtool first, go to flashmode, select a complete/full stock ftf for your phone (whichever version you want, but do double check if the ftf has kernel.sin file in it) and press the flash button. Only once you get the pop up with the animation telling you to connect the phone in flash mode, connect the phone in flashmode (volume - button pressed when connecting cable). As soon as you connect the phone, the flashtool will start its magic and your phone won't turn off.
if you can go in cwm wipe system then you will only be stuck on sony logo then use this guide http://www.youtube.com/watch?v=hPPWRXcsz7g.....it will work because this same happened to me and i fixed it with this method!
-------------------------------------------------------------------
press thanks if i helped
-------------------------------------------------------------------
using xperia u
locked bootloader
jb experience v2.1 rom
Related
Guys, i was upgrading the ROM but this time i used this software, UNIFLASH , it showed some cmd windows, later phone automatically booted to cwm, and then turned off! since then its not turning on neither blinking any LED! guys, please show me a ray , help me! phone is not getting recognized by flashtool either :'( and same with seus
try to hold down power + volume up at the same time until you get the phone to vibrate 3 times, after that try to boot or get it into flashmode with flashtool..
remember.. flashtool is the way to go !
kindly report back or even pm me
realfelix said:
try to hold down power + volume up at the same time until you get the phone to vibrate 3 times, after that try to boot or get it into flashmode with flashtool..
remember.. flashtool is the way to go !
kindly report back or even pm me
Click to expand...
Click to collapse
already tried that, googled a lot already, nothing is helping!
also tried doing what you said with USB connected through my pc, windows kept playing that system sound which comes up when we plus out a device! in particular time intervals, like 3 4 seconds.
bhuvangaur said:
already tried that, googled a lot already, nothing is helping!
also tried doing what you said with USB connected through my pc, windows kept playing that system sound which comes up when we plus out a device! in particular time intervals, like 3 4 seconds.
Click to expand...
Click to collapse
have you tried the fastboot method, it´s in android development, "all you need to know..."
try to flash official stock fw like .452 or .45 with flashtool..try to connect the phone in flashmode....hopefully everything will be alright...
PEACE
guys, phone is not able to boot in any mode, it be fastboot or flashmode! its completely dead thats what i meant earlier. After a lot of researching the whole night, i was able to figure out that the bootloader is that the UNIFLASH corrupted the bootloader. So how to fix that?
try this: make sure you have enough charge and the drivers of your phone are installed correctly. (flashtool drivers)
power+volume up wait till vibrates three times,
then connect your phone to pc.
run the flashtool and prepare the firmwares youre going to flash,
a screen will appear and says turn off your phone....etc
hold power button + volume up wait till vibrates three times
then quickly hold power button + volume down.
it will flash the firmware.
just keep on trying.
mharckk said:
try this: make sure you have enough charge and the drivers of your phone are installed correctly. (flashtool drivers)
power+volume up wait till vibrates three times,
then connect your phone to pc.
run the flashtool and prepare the firmwares youre going to flash,
a screen will appear and says turn off your phone....etc
hold power button + volume up wait till vibrates three times
then quickly hold power button + volume down.
it will flash the firmware.
just keep on trying.
Click to expand...
Click to collapse
its simply not vibrating! i held that combination for like 5 minutes continuous last night, phone has to enter either fastboot or flashmode for flashtool to detect! none of them is coming up, and no LED again when its on charging. complete dead complete mess!
By the way, anyone knows how service center people update the phone's software?
bhuvangaur said:
its simply not vibrating! i held that combination for like 5 minutes continuous last night, phone has to enter either fastboot or flashmode for flashtool to detect! none of them is coming up, and no LED again when its on charging. complete dead complete mess!
By the way, anyone knows how service center people update the phone's software?
Click to expand...
Click to collapse
Go to repair center or phone shop! These guys know how to rewrite ur bootloader through JTAG! Don't worry, u'll get it back once it's done!
Sent From my Lt26i, Hit thank whenever u like!
I think you hard bricked your device... Go to service centre ...
Sent from my LT22i using xda premium
i appreciate you guys for your replies! gave the phone to them yesterday, good to hear about JTAG, will surely revert here and let ya'll know about it! this might happen with any one in future, might help him too!
PS, since the company is no more ericsson based, new service center are SONY one only, where all sony products are welcomed, really good service center now! earlier it was sh*tty since years! i loved the experience this time
bhuvangaur said:
i appreciate you guys for your replies! gave the phone to them yesterday, good to hear about JTAG, will surely revert here and let ya'll know about it! this might happen with any one in future, might help him too!
Click to expand...
Click to collapse
would you please enplane what is JTAG and how it works ?
Had the same problem yesterday!
Maybe a noob advice but here what was my mistake: after switch off the phone with volume up, wait for like 30 second before trying to connect in flash mode. Though my phone was dead but just had to wait a little bit before trying the flash mode. Flashtool heal it!
Sorry for my poor english, I'm french and this is my first post, but I follow xda since a long time!
Bye!
Napolee said:
would you please enplane what is JTAG and how it works ?
Click to expand...
Click to collapse
It a type of connector that is use to connect directly to the phone mainboard. It use to transfer some specific data such as bootloader!
Sent From my Lt26i, Hit thank whenever u like!
this is hilarious!!! a replacement! brand new xperia s! yay!
Trying to Survive my LT26i
I have rooted my phone
put recovery and flashed my rom to xxperience
so everything was ok
using for 2days
so i saw how to overclocked to 1.8ghz and flash via cwm the kernel
after restart from cwm not either the screen turn on
just green light when i put cable on
and when i tried to flash via flash tool given error for error
so i done as say here to hold power + volume up, and the same
so i waited for a little time and try again and its flashing now...
hope it works
Hi guys, yesterday I unlocked and rooted my Xperia U, as I didnt have time anymore, I decided to install the kernel today, so when I installed it, I tried turning on my phone - nothing. I just got that red light thingy sometimes that is active 2-3 seconds, I tried charging but still nothing, funny thing is, when I connect it to my 2nd PC with XP on it, it connects, but in My Computer I only see "Digital Camera" and cant open it, also Windows Explorer popup for it keeps constantly, well, popping up but its empty and I cant select anything. I'm now downloading flashtool, is there anything I can do else? Im desperate, I got this phone for only 3 days.
Okay, now I'm in flashtool, I'm about to start flashing but I cant get into fastboot mode... What should I do?
Bump? :crying:
Please dont make me spam, I searched everything, I'm pretty sure my problem is unique, I cant access fastboot. Nothing
try this:
1. charge your phone for about 1 hour
2. open flashtool then click fastmode and choose your firmware.
3. make sure your phone is off ( i dont know if this is the same with xperia U volume up+power button wait til vibrates three times)
4. when it says connect your phone into fastmode, connect your phone via usb, then hold volume up + power button and wait till it vibrates three times, then hold power button+ volume down.
5. it will flash your firmware.
or you can flash the stock kernel (just extract from ftf, same instructions above).
I charged it for the whole night, the problem is, I cant access fastboot. All the drivers are installed but nothing.
I'm sending my phone for repair probably, with rooting I broke my warrant, what's going to happen?
tavic said:
I charged it for the whole night, the problem is, I cant access fastboot. All the drivers are installed but nothing.
I'm sending my phone for repair probably, with rooting I broke my warrant, what's going to happen?
Click to expand...
Click to collapse
Then y don't you flash it with your firmware via flash mode
Sent From Xperia Sola White (MT27i)
Rooted Stock ICS
Hit Thanks If I Helped!!
Ok fast boot doesn't work,how about Flashboot?
Sent from my LT26i using xda premium
Nope, can't access that either.
Ok does your phone vibrates when you turn it on?Do you have any LED light?Does it respobd to anything?
Sent from my LT26i using xda premium
Not vibrating, also, no led.
The only sign I get is when I take out the battery and put it back in, it vibrates for a second. Thats it.
Try to remove the battery and than try all keys combination,and also try to get to connect it to your flashtool.Try hard reset combination.Remove the battery,put the battery,hold power+vol. up button for. 20 sec. If that doesn't make.Try the same only with vol. down button .If that doesn't work,take it to the service shop than....
Hit Thaks if I helped
Hold vol up when replacing the battery, then quickly shove the USB cable in. Phone should vibrate when you put the battery in and you have a second or two to get it into fastboot or flashboot.
Probably a bad install of a kernel, make sure you're using the right one for your phone.
Not sure if it works for the U, but that's how I fixed my Sola.
Snowstormzzz said:
Hold vol up when replacing the battery, then quickly shove the USB cable in. Phone should vibrate when you put the battery in and you have a second or two to get it into fastboot or flashboot.
Probably a bad install of a kernel, make sure you're using the right one for your phone.
Not sure if it works for the U, but that's how I fixed my Sola.
Click to expand...
Click to collapse
Exactly what I did too. Try again and again. You'll succeed. have stock kernel at hand.
The thing is my Xperia Go is stuck at bootloop and i cant access anything.. no CWM, no entering fastboot and computer doesnt seem to recognize it at all. It only goes up to SONY logo, stays there a while and then blanks the screen just to do it all over again.
It started when i flashed my phone with new kernel.
Any ideas of what should i do now?
All help will be appreciated im new to this.
Install Flashtool, then go the drivers folder in Flashtool, and install your drivers (Including the Fastboot & Flashmode drivers)
Then, turn off your phone. Select the Stock FTF from Flashtool and click Flash
Then, when it asks you connect the phone, Holding Down the Volume Down Key, connect the usb cable to phone (It should already have been connected to pc before connecting to phone)
Wait 2 seconds and a green light comes on.. Then wait a few minutes and your phone will be back to normal
Min3r said:
Install Flashtool, then go the drivers folder in Flashtool, and install your drivers (Including the Fastboot & Flashmode drivers)
Then, turn off your phone. Select the Stock FTF from Flashtool and click Flash
Then, when it asks you connect the phone, Holding Down the Volume Down Key, connect the usb cable to phone (It should already have been connected to pc before connecting to phone)
Wait 2 seconds and a green light comes on.. Then wait a few minutes and your phone will be back to normal
Click to expand...
Click to collapse
I have done all that and did it again just to be sure.. atfer green light comes on it changes to red in few sec and my phone shows SONY for 1/4 min and then shuts off while charging. i have tried to enter fastboot mode too but the same thing happens.. correct led colour few secs and then logo and off.
This seems like a hardbrick although flashing a custom kernel shouldnt have caused that issue.. Did you do the cable connecting in the exact order I said ? You might have missed that ,with any luck
Dun worry
Remove the battery if possible
If not
Switch of the phone by pressing volume us plus power key simultaneously for few seconds
Then flash official ftf via flashtool
---------- Post added at 09:55 AM ---------- Previous post was at 09:54 AM ----------
vikativehkleja said:
I have done all that and did it again just to be sure.. atfer green light comes on it changes to red in few sec and my phone shows SONY for 1/4 min and then shuts off while charging. i have tried to enter fastboot mode too but the same thing happens.. correct led colour few secs and then logo and off.
Click to expand...
Click to collapse
Its because u r not connecting it properly
While connecting keep only the volume down button pressed ( dun press the power key along to enter flashmode)
And its not a hard brick so dun worry
Just a bad kernel
drsanket_xperia_u said:
Dun worry
Remove the battery if possible
If not
Switch of the phone by pressing volume us plus power key simultaneously for few seconds
Then flash official ftf via flashtool
---------- Post added at 09:55 AM ---------- Previous post was at 09:54 AM ----------
Its because u r not connecting it properly
While connecting keep only the volume down button pressed ( dun press the power key along to enter flashmode)
And its not a hard brick so dun worry
Just a bad kernel
Click to expand...
Click to collapse
This is weird and awkward.. when i started my computer today, read this and redid all the steps i got it to flash and it WORKS!
This incident has made me even more interested.
Thanks to BOTH of you for taking the time to answer, i know it was a stupid question to begin with.
vikativehkleja said:
This is weird and awkward.. when i started my computer today, read this and redid all the steps i got it to flash and it WORKS!
This incident has made me even more interested.
Thanks to BOTH of you for taking the time to answer, i know it was a stupid question to begin with.
Click to expand...
Click to collapse
Anytime buddy
I've tried to install Cyanogenmod 9 on my Xperia Sola, I've unlocked bootloader official way, flashed kernel from this forum specialy made for sola (http://forum.xda-developers.com/showthread.php?p=28957468&postcount=412 This One), then boot.img of cyanogenmod 9 (FXP203) and...
When I want to do anything with phone, it just flashes my red led. I mean, that led is still on, when I press Power it just turn off. And when I try to connect my phone in fastboot mode, It don't react at all. Can I already throw it away through window?
I put it under a charger to see if it's just off energy, but i've noticed, that after a while, red led just turns off and that's all.
My god, help me or I'll be back on Nokia 3310
You've used the S kernel, not the Sola.
Download the FXP for Sola (Pepper) here;
http://forum.xda-developers.com/showthread.php?t=1876929
Flash boot.img via fastboot. To get in, hold vol up + power. Wait for 3 vibrations.
Hold vol up. Then jam the USB cable in. You should be in fastboot.
Alternatively, flash the stock sola ftf via flashboot.
Problem is, my phone does not react, it does not vibrate, just that red led is on or off. Nothing else. I've tried all of those combinations. I can't get to fastboot mode or anything else.
MelaPL said:
Problem is, my phone does not react, it does not vibrate, just that red led is on or off. Nothing else. I've tried all of those combinations. I can't get to fastboot mode or anything else.
Click to expand...
Click to collapse
Happened to me (I use Xperia GO). What I did is (as mentioned above) - Hold the power button and Volume Up button for sometime (it vibrates once after a few seconds, do not leave the buttons - continue to do so and after a few more seconds until 3 vibrations) and then the phone switches off. Now, hold the Volume Up button and plug in the USB cable - you'd be able to get in the fastboot mode. Flash a stock kernal and that should help.
If your phone is completely down (no charge at all), then above won't help. Plugin the charger and and wait for a few mins (before the red light goes off - you should now have a good knowledge on when the light goes off!) and try then try the above step. Once the 3 vibration comes, remove the charger and go ahead with the flash mode.
Hope this helps!
Thanks,
B.
Edit: By the way, I had my SIM Card and Memory card inserted in the phone when the phone was completely down without any charge. I don't know how, but it makes a difference with you try so (atleast in my case) with them.
If it does not vibrate, then it's a hard brick =\ You need the phone to be at least partially responsive to get into fastboot/flashboot.
Keep holding down. It should vibrate after 25 seconds or so.
Otherwise, you have to bring it to Sony and tell them their phone died on you.
Right now It dosen't even blink with Led. It's totaly down. I cant lock fbootloader, so I'm doomned. Hope that won't cost much...
Install Sony Update Service (SUS) and try to recover your phone from there.
Last shot here, but here's to hoping that the PC at least detects your phone.
Otherwise.... Yeah =\
If you unlocked your bootloader Pc companion will be useless for you cause it will not detect your phone,.,,
i think other way is to flash the stock ftf for you device using flashtool.... that wuld be the best shot for you...
please respond if this fix your problem
No, SUS will detect, but will refuse to flash. It will say "Phone has been modified".
Need to see whether it's a hard brick. If even SUS does not recognise, then bring it to Sony =\
None of the above works. It's just dead and sometimes flashes red light. PC Companion says that there's no phone connected. Hope I will be able to gain a varranty or I'll be on Nokia 3310. But I'm not verry cheerful about that...
Flashtool does not react when I plug in my phone in fastboot or flash.
Hey bro,
Its highly unlikely for hardbrick to happen to Sony phones by flashing a differnt Kernel when Flashtool is there Pretty sure that it ought to work, follow the steps below (Note that the order of usb cable connection is the most important thing as doing it wrong will not allow Flashtool to connect to the phone when its bricked ! )
First, try plugging it in to charger for a while to ensure that there's some charge. Follow up with the Vol and power Button to make sure its turned off. Then after that follow this procedure *exactly*
1) Prepare Flashtool and select the FTF. (Flashmode )
2) When flashtool asks yo to connect the phone, connect the USB cable to PC
3) Then, holding down ONLY the Vol Down button (No Power button, Note that ) connect the phone to the USB cable and in a few seconds, Flashtool will start flashing
I know you tried many variations but missing out on one or the other detail during your previous tries might have caused the lack of success Just try it and let us know what happens
Best of luck and hope you dont have to go to Nokia World !
Cheers
Nope, it's still not working. It just dosent detect phone. I'm pluging in, holding only volume key and I'm waiting 5 minutes - nothing happend.
Nokia 5530 for now, but come one...
Hi,
I am currently having the same problem (I have bricked my sola by flashing with fxp boot.img). After digging the internet I found out that you can start fastboot by:
1. holding all 3 buttons (power on, volume +, volume -)
2. the phone will vibrate
3. the phone will vibrate 3 times
4. release the buttons
5. hold the volume + button and plug in the cable
6. you should be in fastboot now (blue light on)
If fastboot does not work then do 1-4 3x. Good luck! Hopefully we will unbrick our phones
Br,
Wermesz
wermesz said:
Hi,
I am currently having the same problem (I have bricked my sola by flashing with fxp boot.img). After digging the internet I found out that you can start fastboot by:
1. holding all 3 buttons (power on, volume +, volume -)
2. the phone will vibrate
3. the phone will vibrate 3 times
4. release the buttons
5. hold the volume + button and plug in the cable
6. you should be in fastboot now (blue light on)
If fastboot does not work then do 1-4 3x. Good luck! Hopefully we will unbrick our phones
Br,
Wermesz
Click to expand...
Click to collapse
Lol things u get on the internet!!!
First there is no such key combination to start fastboot k so just dun break ur buttons in an attempt to start it ...
Steps 1,2&3 are steps to get ur device force restart and force shutdown and let me tell you one thing
step 1 is wrong it power button and volume + button. That's it first the phone will vibrate once for force restart and if u keep pressing it will bypass over to force shutdown which is indicated by 3 vibrations..
Sent from my Xperia Sola using xda premium
could work
I have a Xperia U and triying to port JB to it I briked two or three times.
I hold power botom and it vibrate and doesnt happen anything ok.?¿
The possible solution could be this(for my works)
Charge the phone like 1 hour for my doesnt charge with the animation but its for security.
With the nest steps you are going to lose all CWM and tweaks and apks but personal data still there.
You have two options:
Flash a new rom with flashtool, but when you pluged with volum - you hold it for allmost all process becose for my i conect to PC and its goes quikly so i cant do annything.
If the phone is not recognised by Flashtool:
You have to repair it with PC Companion or Bridge for Mac, and also the same hold volum - almost all process.
For my it works, tell my if for you works:cyclops::cyclops::cyclops:
Hi,
it worked !
after doing the steps I have posted earlier I managed to flash my xperia sola with the right boot.img (the one from fxp pepper) and install fxp via CWM. Should work for you too.
One tip: you have to remove the assert from fxp installation script.
Br,
Wermesz
@op, your battery is dead and isn't accepting any external charge. Try replacing your battery with a charged one. That is if sola supports user replaceable batteries.
Sent from my ST25i using xda app-developers app
Hey guys im in a lot of trouble right now. I have bricked my device and im not sure if i will be able to restore it back. Im not worried about the data in the device anymore,i just want my device booting back into any OS possible!!
Here's what happened,i was flashing the stock firmware of the device through flashtool.The process was about half done.All of a sudden my device fell down from my computer desk.The cable got disconnected and the device doesn't boot anymore.Any solutions to make it boot back up? Please help...
Hello there
When you connect your XU to PC with volume buttons pressed, Does the LED light up?
I hope you just made a soft brick to your phone, not Hard Brick.
When i connect the device a green flash comes up for like a microsecond and thats it.Then the device is as good as dead.The same thing happens when i connect the device to the pc,a momentary flash of green light and then back to dead...When i connect the device by holding the vol up button,the same thing happens.. only with a blue coloured flash of light.The device is not recognised by sony pc companion either.
krazzyK said:
When i connect the device a green flash comes up for like a microsecond and thats it.Then the device is as good as dead.The same thing happens when i connect the device to the pc,a momentary flash of green light and then back to dead...When i connect the device by holding the vol up button,the same thing happens.. only with a blue coloured flash of light.The device is not recognised by sony pc companion either.
Click to expand...
Click to collapse
Reflash it using flashtool hold volume up and power botton leave it after it viberates 3 times it means that it is now switched off.
Now use flash it with flashtool you'll get your device back.
Give it a try and let me know.
its just of 5 to 10 mint work ,,,,,remove the battery for 3 sec and put it back into mobile ,,,hold volume down and plugin the USB cable in mobile ,,,u r will switch to flashboot mod by green light down to led bar,,,,,now flash official stock ROM ,,,,at installing time at 75% it will take time so plz be wait to complete
Thanks everybody
finally i could get my device into flash mode and then i flashed stock firmware... The device is running fine now... though i lost all my data.
Thanks everybody i love the dev support here for this device.