The thing is my Xperia Go is stuck at bootloop and i cant access anything.. no CWM, no entering fastboot and computer doesnt seem to recognize it at all. It only goes up to SONY logo, stays there a while and then blanks the screen just to do it all over again.
It started when i flashed my phone with new kernel.
Any ideas of what should i do now?
All help will be appreciated im new to this.
Install Flashtool, then go the drivers folder in Flashtool, and install your drivers (Including the Fastboot & Flashmode drivers)
Then, turn off your phone. Select the Stock FTF from Flashtool and click Flash
Then, when it asks you connect the phone, Holding Down the Volume Down Key, connect the usb cable to phone (It should already have been connected to pc before connecting to phone)
Wait 2 seconds and a green light comes on.. Then wait a few minutes and your phone will be back to normal
Min3r said:
Install Flashtool, then go the drivers folder in Flashtool, and install your drivers (Including the Fastboot & Flashmode drivers)
Then, turn off your phone. Select the Stock FTF from Flashtool and click Flash
Then, when it asks you connect the phone, Holding Down the Volume Down Key, connect the usb cable to phone (It should already have been connected to pc before connecting to phone)
Wait 2 seconds and a green light comes on.. Then wait a few minutes and your phone will be back to normal
Click to expand...
Click to collapse
I have done all that and did it again just to be sure.. atfer green light comes on it changes to red in few sec and my phone shows SONY for 1/4 min and then shuts off while charging. i have tried to enter fastboot mode too but the same thing happens.. correct led colour few secs and then logo and off.
This seems like a hardbrick although flashing a custom kernel shouldnt have caused that issue.. Did you do the cable connecting in the exact order I said ? You might have missed that ,with any luck
Dun worry
Remove the battery if possible
If not
Switch of the phone by pressing volume us plus power key simultaneously for few seconds
Then flash official ftf via flashtool
---------- Post added at 09:55 AM ---------- Previous post was at 09:54 AM ----------
vikativehkleja said:
I have done all that and did it again just to be sure.. atfer green light comes on it changes to red in few sec and my phone shows SONY for 1/4 min and then shuts off while charging. i have tried to enter fastboot mode too but the same thing happens.. correct led colour few secs and then logo and off.
Click to expand...
Click to collapse
Its because u r not connecting it properly
While connecting keep only the volume down button pressed ( dun press the power key along to enter flashmode)
And its not a hard brick so dun worry
Just a bad kernel
drsanket_xperia_u said:
Dun worry
Remove the battery if possible
If not
Switch of the phone by pressing volume us plus power key simultaneously for few seconds
Then flash official ftf via flashtool
---------- Post added at 09:55 AM ---------- Previous post was at 09:54 AM ----------
Its because u r not connecting it properly
While connecting keep only the volume down button pressed ( dun press the power key along to enter flashmode)
And its not a hard brick so dun worry
Just a bad kernel
Click to expand...
Click to collapse
This is weird and awkward.. when i started my computer today, read this and redid all the steps i got it to flash and it WORKS!
This incident has made me even more interested.
Thanks to BOTH of you for taking the time to answer, i know it was a stupid question to begin with.
vikativehkleja said:
This is weird and awkward.. when i started my computer today, read this and redid all the steps i got it to flash and it WORKS!
This incident has made me even more interested.
Thanks to BOTH of you for taking the time to answer, i know it was a stupid question to begin with.
Click to expand...
Click to collapse
Anytime buddy
Related
While updating a new Xperia U to ICS the PCC had an error while flashing the new firmware. Now the screen lights up, the sony logo is shown for ~3-5 seconds and then it reboots.
After that I have been unable to get it recognized again by either PCC/SUS or flash tool.
I also checked my log files in Linux and no device appears.
I've tried 3 different machines (2x Windows 8, 1x Win 7), multiple USB ports. Also leaving the battery out for ~30 mins didn't change the behavior.
The green light for download mode comes on, but after about 5 seconds the light goes out and it goes into the boot loop again.
So by now I believe the device needs to be sent in, but maybe some one has a few more things I can try.
Try pressing the volume down plus volume up plus power button all 3 simultaneously till u feel 3 vibrations
Sent from my ST25i using Tapatalk 2
Can you make sure the Flashtool drivers are installed ? Go to Flashtool Directory, open drivers directory and start the setup.. Make sure to select the Flashmode and Fastboot drivers are also selected. Then, reboot System and folow this order.
Startt flashtool,select f/w, wait for Flashtool to tell you to connect to device. Then, holding the Volume down button (while phone is switched off), plug the cable into phone (The usb cable must already be connected to PC before starting the Flash Procedure )
The Order is very important.. I had same issue with U (althoguh mine crashed with Flashtool and same as what you observed. When I followed this order, I was able to get it detected and flashed )
Hopefully, you wont need to return to Service Center
let me know how it goes
Cheers ! & Merry Christmas
And yes I forgot to mention
Wrong section
Plz use question n answer section next tym
Sent from my ST25i using Tapatalk 2
drsanket_xperia_u said:
Try pressing the volume down plus volume up plus power button all 3 simultaneously till u feel 3 vibrations
Sent from my ST25i using Tapatalk 2
Click to expand...
Click to collapse
No response, I've tried holding all three buttons for a minute, but it doesn't vibrate after turning on. The only way I can turn it off is by removing the battery.
Min3r said:
Can you make sure the Flashtool drivers are installed ? Go to Flashtool Directory, open drivers directory and start the setup.. Make sure to select the Flashmode and Fastboot drivers are also selected. Then, reboot System and folow this order.
Startt flashtool,select f/w, wait for Flashtool to tell you to connect to device. Then, holding the Volume down button (while phone is switched off), plug the cable into phone (The usb cable must already be connected to PC before starting the Flash Procedure )
The Order is very important.. I had same issue with U (althoguh mine crashed with Flashtool and same as what you observed. When I followed this order, I was able to get it detected and flashed )
Hopefully, you wont need to return to Service Center
let me know how it goes
Cheers ! & Merry Christmas
Click to expand...
Click to collapse
I tried that right now, Flashmode and Fastboot drivers are installed. Flash tool is ready, device is plugged in with volume down pressed, green light comes on. Nothing is found on the PC, after about 5 seconds the green light turns off and the phone shows the sony logo. Green light also comes on if i simply plug in the usb without volume down pressed. So I'm thinking, the download mode has some how been corrupted?
drsanket_xperia_u said:
And yes I forgot to mention
Wrong section
Plz use question n answer section next tym
Sent from my ST25i using Tapatalk 2
Click to expand...
Click to collapse
Sorry about that, maybe a moderator can move my topic to the right section.
Are u connecting it properly???
Make sure when u connect ur cell to ur pc u have nt presed the power key
keep the phone off
Press the volume down button ( keep it pressed, dun
leave it) and connect it to the usb
U will see green light
Darn.. That looks bad.. That did it for me on every occasion. I think you might have a hardbrick due to the interrupted write cycle so I dont think any other way except to take it to Service Center
Sorry I couldnt help
drsanket_xperia_u said:
Are u connecting it properly???
Make sure when u connect ur cell to ur pc u have nt presed the power key
keep the phone off
Press the volume down button ( keep it pressed, dun
leave it) and connect it to the usb
U will see green light
Click to expand...
Click to collapse
Exactly what I'm doing and the green light does come on. Except it decides to go into a boot loop after it apperantly boots into download mode but doesn't stay there.
Min3r said:
Darn.. That looks bad.. That did it for me on every occasion. I think you might have a hardbrick due to the interrupted write cycle so I dont think any other way except to take it to Service Center
Sorry I couldnt help
Click to expand...
Click to collapse
That's what I've been fearing. In which case it goes back to the seller in the hope that he will send me a new device.
Moved
Is there any chance of properly reactivating flashmode by using a JTAG?
Cebalrai said:
Is there any chance of properly reactivating flashmode by using a JTAG?
Click to expand...
Click to collapse
Risky business
Jtag. ...used for hard bricked devices n. Seen max to work wid samsung phones only....
Wont recommend u too open up ur xu
Let the service center try first
Sent from my GT-N7000 using Tapatalk 2
Have you manage to recover your phone without taking it to service?
I'm in the exactly same situation... Any help is welcome...
While trying to enter flashmode, green light turns on but after some secs it turns off and sony logo appears on screen. any chance to recover this beautiful brick ?
thanks
After several tries (a lot of...) I manage to enter flashmode and SUS is now reinstalling sony ROM.
Honestly I don´t know how it works this time and not the others but i'm happy with it independently of what happens.
... seems flashtool is detecting ur phone try to flash first the stock kernel and do not wipe everything it shud be in timing though.. onces it is flash charge ur phone in kernel mode (phone is off) then you can flash the stock fw of ur XU.
I bricked my phone
I bricked my xperia U as well... When i tried to power ON, it just vibrates and nothing happens, i dont even get the sony logo. When i get into flash boot mode it gets connected but after 20secs, the phone turns off again. Only fastboot mode stays on. How can i unbrick my phone??? Plz help. I made a mistake by flashing the custom jelly bean rom without flashing the kernel first.
adithyasailesh said:
I bricked my xperia U as well... When i tried to power ON, it just vibrates and nothing happens, i dont even get the sony logo. When i get into flash boot mode it gets connected but after 20secs, the phone turns off again. Only fastboot mode stays on. How can i unbrick my phone??? Plz help. I made a mistake by flashing the custom jelly bean rom without flashing the kernel first.
Click to expand...
Click to collapse
No worries. The phone turns off because it doesn't receive any signal from the PC - many people make the mistake of connecting the device in flashmode first, and then they start the flashtool etc.
Instead, load the flashtool first, go to flashmode, select a complete/full stock ftf for your phone (whichever version you want, but do double check if the ftf has kernel.sin file in it) and press the flash button. Only once you get the pop up with the animation telling you to connect the phone in flash mode, connect the phone in flashmode (volume - button pressed when connecting cable). As soon as you connect the phone, the flashtool will start its magic and your phone won't turn off.
if you can go in cwm wipe system then you will only be stuck on sony logo then use this guide http://www.youtube.com/watch?v=hPPWRXcsz7g.....it will work because this same happened to me and i fixed it with this method!
-------------------------------------------------------------------
press thanks if i helped
-------------------------------------------------------------------
using xperia u
locked bootloader
jb experience v2.1 rom
Hi all this is my first post here.
I flashed the CM10.2 by munjeni but i forgot to format /system
Now my Sola doesn't even start, when i try starting it vibrates and nothing happens
If i charge it and try to start it vibrates, the red led lights for a second and then.. nothing
My PC doesn't recognize it and if i try to fastboot or flash the purple/green led lights fot three seconds and then turns off and flashtool doesn't see the device
PLEASE HELP!!!!!!
ametyst said:
Hi all this is my first post here.
I flashed the CM10.2 by munjeni but i forgot to format /system
Now my Sola doesn't even start, when i try starting it vibrates and nothing happens
If i charge it and try to start it vibrates, the red led lights for a second and then.. nothing
My PC doesn't recognize it and if i try to fastboot or flash the purple/green led lights fot three seconds and then turns off and flashtool doesn't see the device
PLEASE HELP!!!!!!
Click to expand...
Click to collapse
Is your bootloader unlocked?
Make sure it's turned off by pressing power + volume up until you feel 1 + 3 vibrations before attempting fastboot or flash mode.
ChikeD said:
Is your bootloader unlocked?
Make sure it's turned off by pressing power + volume up until you feel 1 + 3 vibrations before attempting fastboot or flash mode.
Click to expand...
Click to collapse
Yes, it's unlocked
Yes, I tried
Please someone help!!!!
Could you connect fastboot/flash mode on the PC you are using now before it happen?
Ok, here it goes...
You know? The same exact thing happened to me, I'll tell you the solution. (yeah, sound like a TV commercial)
Power off the phone by pressing and holding the Power and Volume up buttons, when it vibrates three times release.
Now you have to turn it on in fastboot mode, connect the phone to the computer, press the power and vol up buttons, after two seconds release the power button and you have the blue led, always hold the up button.
Now at this time you need to be fast as ****, because you need to flash the boot.iso kernel in the .zip, if your phone is recognized by flashtool, obviously.
When you have the kernel flashed then reboot the phone and hold the vol up button when the led of many colors blinks, and hell yeah, we are on CWM. At this step, you have to do the same procedure as you did, but be careful this time. If something happens just tell me.
Don't forget to format the system.
---------- Post added at 04:32 PM ---------- Previous post was at 04:31 PM ----------
Just a fact, there's a lot, but a LOT of threads that are made because of the munjeni's ROM, if you have a doubt, search first, then post.
manudo said:
Ok, here it goes...
You know? The same exact thing happened to me, I'll tell you the solution. (yeah, sound like a TV commercial)
Power off the phone by pressing and holding the Power and Volume up buttons, when it vibrates three times release.
Now you have to turn it on in fastboot mode, connect the phone to the computer, press the power and vol up buttons, after two seconds release the power button and you have the blue led, always hold the up button.
Now at this time you need to be fast as ****, because you need to flash the boot.iso kernel in the .zip, if your phone is recognized by flashtool, obviously.
When you have the kernel flashed then reboot the phone and hold the vol up button when the led of many colors blinks, and hell yeah, we are on CWM. At this step, you have to do the same procedure as you did, but be careful this time. If something happens just tell me.
Don't forget to format the system.
---------- Post added at 04:32 PM ---------- Previous post was at 04:31 PM ----------
Just a fact, there's a lot, but a LOT of threads that are made because of the munjeni's ROM, if you have a doubt, search first, then post.
Click to expand...
Click to collapse
Flashtool says "ERROR - This action can only be done in fastboot mode"
My PC doesn't recognise the phone
Please help
ametyst said:
Flashtool says "ERROR - This action can only be done in fastboot mode"
My PC doesn't recognise the phone
Please help
Click to expand...
Click to collapse
Press volume up + USB to PC that should go into fastboot mode
Sent From My Xperia U With An Ultimate XNovaThor Rom
dara007_168 said:
Press volume up + USB to PC that should go into fastboot mode
Sent From My Xperia U With An Ultimate XNovaThor Rom
Click to expand...
Click to collapse
It doesn't stay in fastboot mode. Purple light is on for like 2 or 3 seconds and then it turns off and my pc doesn't recognize the device!!!
All driver installed!!
ametyst said:
It doesn't stay in fastboot mode. Purple light is on for like 2 or 3 seconds and then it turns off and my pc doesn't recognize the device!!!
All driver installed!!
Click to expand...
Click to collapse
U mean Blue light? Pc doesn't recognize doesn't mean that driver problem maybe change usb and try again
Sent From My Xperia U With An Ultimate XNovaThor Rom
ametyst said:
It doesn't stay in fastboot mode. Purple light is on for like 2 or 3 seconds and then it turns off and my pc doesn't recognize the device!!!
All driver installed!!
Click to expand...
Click to collapse
Read my post dude, connect the USB cable, hold power and vol up buttons and two seconds later release power button and continue holding up.
In that time you should flash the boot.iso, but quick.
which os you are using in your pc ?
Solved
Thank you all guys, I think it was a driver problem.
I was using a Pc OS Windows 8, and it didn't recognize the phone.
I tried with a Win 7 PC, installed driver and everything, and i succeded to flash the boot.img
ametyst said:
Thank you all guys, I think it was a driver problem.
I was using a Pc OS Windows 8, and it didn't recognize the phone.
I tried with a Win 7 PC, installed driver and everything, and i succeded to flash the boot.img
Click to expand...
Click to collapse
You can flash from Windows 8 too, just you have to read this guide. http://forum.xda-developers.com/showthread.php?t=2447283
But, ok, you flashed it, great.
More specificly, I used to have Win 8.1
Now, for other causes I'm back to Win 8 and from here i can flash perfectly
I'm writing this for someone else who may have the same issue
:good:
My phone is bricked and even if i want to flash a ftf at flashtool it doesn't sees my phone :crying::crying: When i connect the wall charger sony logo comes and red led lights then everything closes. And when i hold volume up+power phone vibrates first once then three times. please help
VOL UP+POWER =3 VIBRATION, mean you turn off the phone. No problem.
Step by step.
Turn off the phone. hold volume - and conect to computer. The led turn green?
The same, but with volume+ ¿the led turn blue?
Is very dificult brick totally the phone, we will unbrick, dont worry.
Flamenawer said:
VOL UP+POWER =3 VIBRATION, mean you turn off the phone. No problem.
Step by step.
Turn off the phone. hold volume - and conect to computer. The led turn green?
The same, but with volume+ ¿the led turn blue?
Is very dificult brick totally the phone, we will unbrick, dont worry.
Click to expand...
Click to collapse
Yes if i hold vol up+power blue led comes and if i vol down+power green light comes. At flashtool i selected fastboot and selected flash kernel and flashed recovery.img as kernel. and that happened. i think thats the problem but is there a way to fix it?
Yes!!!!!! You're doing it totally wrong.
Recovery must be sideloaded via adb shell.
You'll need to flash your firmware and then follow the right steps to sideload a new recovery.
Enviado desde mi E2306 mediante Tapatalk
To unbrick you phone the only needed is flash your stock rom,excluding all minus the kernel. This will work and you hold your recovery with the phone working and you will can flash the root zip.
Flamenawer said:
To unbrick you phone the only needed is flash your stock rom,excluding all minus the kernel. This will work and you hold your recovery with the phone working and you will can flash the root zip.
Click to expand...
Click to collapse
But the problem is flashtool doesnt't recognize my phone now. if i can solve this i can open my phone again but how?
Please try put here the log. Uninstall flashtool 9.19,is buged, and install 9.18 and try again. Flashmode and check all except kernel
Flamenawer said:
Please try put here the log. Uninstall flashtool 9.19,is buged, and install 9.18 and try again. Flashmode and check all except kernel
Click to expand...
Click to collapse
i installed 9.18. i connected the phone to the pc when i connect phone to pc the led become green. and i opened the flashtool. in the log it says device connected in flash mode. but when i click the bolt and select the flashmode my device doesnt appears there. and after a while it says device disconnected
vurucumiller said:
i installed 9.18. i connected the phone to the pc when i connect phone to pc the led become green. and i opened the flashtool. in the log it says device connected in flash mode. but when i click the bolt and select the flashmode my device doesnt appears there. and after a while it says device disconnected
Click to expand...
Click to collapse
Change the order, first run flashtool,flashmode,selec the rom,check all except kernel,wait,after flastool say you connect the phone.
Turn the phone off with volume up + power until vibrate 3 times. push and hold volume- and connect the usb to the computer, the flash will start.
Flamenawer said:
Change the order, first run flashtool,flashmode,selec the rom,check all except kernel,wait,after flastool say you connect the phone.
Turn the phone off with volume up + power until vibrate 3 times. push and hold volume- and connect the usb to the computer, the flash will start.
Click to expand...
Click to collapse
Thank ill try when downloaded the ftf
Flamenawer said:
Change the order, first run flashtool,flashmode,selec the rom,check all except kernel,wait,after flastool say you connect the phone.
Turn the phone off with volume up + power until vibrate 3 times. push and hold volume- and connect the usb to the computer, the flash will start.
Click to expand...
Click to collapse
It worked so much thanks you are my lifesaver :good::good:
Im happy for help you, I will have a good day for this. Enjoy
Dont mind me
I need 10 posts to post a picture
i know i'm probably late but when I boot into flashmode and the green light comes on, after a bit it disconnects from my pc and then reconnects, interrupting the process, can anyone help?
JakeMini123 said:
i know i'm probably late but when I boot into flashmode and the green light comes on, after a bit it disconnects from my pc and then reconnects, interrupting the process, can anyone help?
Click to expand...
Click to collapse
Interupting the process? Same hapened to me. Be sure to connect your phone only when everything is ready, so when the flashtool asks you to connect your phone, and not before. Worked for me.
ekin_strops said:
Interupting the process? Same hapened to me. Be sure to connect your phone only when everything is ready, so when the flashtool asks you to connect your phone, and not before. Worked for me.
Click to expand...
Click to collapse
I do connect the phone when everything is ready and flash tool tells me to connect flash tool in flash mode, but it's like a bomb, the green light stays green for about 10 seconds, goes back to red then in 2 seconds back to green so i can never flash anything in time, please help
JakeMini123 said:
I do connect the phone when everything is ready and flash tool tells me to connect flash tool in flash mode, but it's like a bomb, the green light stays green for about 10 seconds, goes back to red then in 2 seconds back to green so i can never flash anything in time, please help
Click to expand...
Click to collapse
It could be also your drivers. Which windows do you have?
What should i do of it goes into the select language part but when i try to select anything it doesn't respond and just restarts again and again. Even if i tried rebooting through twrp it's still the same
Please help.
ekin_strops said:
It could be also your drivers. Which windows do you have?
Click to expand...
Click to collapse
Windows 7 but all the drivers are installled and working fine from the last time I plugged in my xperia.
JakeMini123 said:
Windows 7 but all the drivers are installled and working fine from the last time I plugged in my xperia.
Click to expand...
Click to collapse
Pluged in like file transfer or like flashmode and fastboot mode?
So I think I bricked my phone ya all. I used the one click root after I unlocked boot loader and everything worked fine until I had to reboot my phone. All of a sudden the nfc has crashed pop up made my phone inoperable. I booted into twrp with the intention to wipe cache. After I did that the phone stopped booting all together.
I tried putting the phone in fast pot mode and the blue led displays but it's not being recognized by the pc. I downloaded flash tool hoping I can flash a stock image back but same issues. If I press volume down the led turns green and for a few seconds flash tool will recognize the phone.
Does anyone have any ideas? Phone now turns on but won't go past the splash screen where Sony logo is displayed.
If flash tool recognizes phone and there is light game is not lost. I would call this semi-brick. Did you flash all? Maybe you just need to try again.
orbphobic1 said:
So I think I bricked my phone ya all. I used the one click root after I unlocked boot loader and everything worked fine until I had to reboot my phone. All of a sudden the nfc has crashed pop up made my phone inoperable. I booted into twrp with the intention to wipe cache. After I did that the phone stopped booting all together.
I tried putting the phone in fast pot mode and the blue led displays but it's not being recognized by the pc. I downloaded flash tool hoping I can flash a stock image back but same issues. If I press volume down the led turns green and for a few seconds flash tool will recognize the phone.
Does anyone have any ideas? Phone now turns on but won't go past the splash screen where Sony logo is displayed.
Click to expand...
Click to collapse
Select firmware on flashtool and prepare ot for flashing. When flashtool prompts you to connect your phone, do it then. That way it will stay on flashmode
Sadman Khan said:
Select firmware on flashtool and prepare ot for flashing. When flashtool prompts you to connect your phone, do it then. That way it will stay on flashmode
Click to expand...
Click to collapse
The thing is when I put the phone in fastboot mode it does not vibrate like it used to. Right now the led just turns blue and nothing happens. Flashtool won't even recognize the phone when its in this state. If I disconnect from cable and press the volume down key the led turns green and for a few seconds flashtool will identify the phone but then it stops...
Flashmode is when you use volume down. When flashtool prompts you to connect the phone, only then press and hold volume down button while connecting. The flashing will begin immediately.
---------- Post added at 08:25 PM ---------- Previous post was at 08:22 PM ----------
Fastboot is volume up. That's just for flashing kernels usually. For flashing ftfs use flashmode which is accessed using volume down. First go to flashtool, click on the flash icon, click on flashmode, select the firmware and click flash. Then wait. When flashtool tells prompts you to connect, only then do so. Also, use the latest flashtool and the latest drivers
Sadman Khan said:
Flashmode is when you use volume down. When flashtool prompts you to connect the phone, only then press and hold volume down button while connecting. The flashing will begin immediately.
---------- Post added at 08:25 PM ---------- Previous post was at 08:22 PM ----------
Fastboot is volume up. That's just for flashing kernels usually. For flashing ftfs use flashmode which is accessed using volume down. First go to flashtool, click on the flash icon, click on flashmode, select the firmware and click flash. Then wait. When flashtool tells prompts you to connect, only then do so. Also, use the lastest flashtool and the latest drivers
Click to expand...
Click to collapse
Sadman thank you. That worked.
orbphobic1 said:
Sadman thank you. That worked.
Click to expand...
Click to collapse
Glad to help
Hi Friends
I was in charge phone
After 20 minutes I could not charging
And when he was off again did not Charge
But with a little dock charged
But when it became clear I wrote you that wipes recovery system unmunt after I reboot
And the Sony logo on the left
Instead, he was still charging connector Repair
You flash mode lamp Green was a moment but off the field
Fast-boot mode after you turn the blue lights but not recognized by the computer
It's now clear the field, but the Sony logo
Teachers Review Body
I cannot understand what are you saying. Are you in a bootloop.
Hariskh said:
I cannot understand what are you saying. Are you in a bootloop.
Click to expand...
Click to collapse
no,my phone stuck in Sony splashscreen and not going to the flash mod , so just going into the fast boot mod but not recognize by computer
samad_asheq said:
no,my phone stuck in Sony splashscreen and not going to the flash mod , so just going into the fast boot mod but not recognize by computer
Click to expand...
Click to collapse
>> restart your PC
>> if it still happens
>>you need to install driver for your phone, which is located in C: /flashtool
>>after installation you may reboot your PC
>>now first unplug the cable ..
>>Press power and volume + key until your phone vibrates 3 times
>>now first plug your phone to the cable and then only on PC when flashtool prompts holding the volume down key..
---------- Post added at 06:52 PM ---------- Previous post was at 06:45 PM ----------
you need to install drivers located in C:/ flashtool folder
>> reboot
>>switch your phone off
>>plug in the cable in your phone first and when flashtool prompts to connect your phone;
connect it holding the volume down key
you will be in flashmod
problem as motherbord