Hi guys, yesterday I rooted my SG2 with Jelly Bean 4.1.2 XXLSJ, it wasnt done in download mode, i put the zip file on sd card and went into stock recovery and used apply update from sd card and then rebooted but now my phone hangs at the Samsung Galaxy SII screen until i remove the battery or go back into recovery
I can get into recovery but when i reboot the phone it just hangs . Ive wiped the data and cache and re flashed the zip file but it still hangs
Any help please
Download Philz.tar or Siyah 6.04.tar kernel and put it to phone via odin.
grisoxxl said:
Download Philz.tar or Siyah 6.04.tar kernel and put it to phone via odin.
Click to expand...
Click to collapse
does the phone have to be in USB Debugging mode, if so im stuck
Do not worry of USB Debugging mode.
Follow this steps just use kernel from attachments.
- (USB) Disconnect your phone from your computer
- Start ODIN
- Click the PDA button, and select siyah.tar
- Put your phone in download mode(vol down+power+menu button)
- (USB) Connect the phone to your computer
- Make sure repartition is NOT checked
- Click the START button
- Wait for the phone to reboot
Ive used Odin to reflash my phone with Siyah 6.04.tar kernel. According to Odin everything was ok but when phone rebooted i got the Samsung Galaxy SII screen this time with the yellow triangle and then the phone goes blank, ie turns off and nothing else
In recovery mode clean cache, dalvik cache and fix permision, if this dont help install new rom.
grisoxxl said:
In recovery mode clean cache, dalvik cache and fix permision, if this dont help install new rom.
Click to expand...
Click to collapse
still no luck, any suggestions on new ROM
oohmygod831 said:
still no luck, any suggestions on new ROM
Click to expand...
Click to collapse
It is up to you. My is in my signature(I'm satisfied with it).
Maybe try Flash Stock rom ? And then Flash XXLSJ ?
Basically you stuck in a boot loop ...reason behind it is bad boot img., according to me. You can try restoring only system (in advance restore) or the entire nandroid itself, This is only if you have a backup done before.
Related
Im a noob, so basically I rooted my phone and went into CWM recovery to flash a new ROM but stupid me didnt back up my stock ROM, and also I totally fogot to download a Custom ROM onto my sd card, so I went into CWM and cleared cache, clear data/factory reset, and rebooted but then it kept turning on and kept on doing that, the samsung logo comes on then keeps repeating.
After I went in cwm again and clear davnik cache, wipe cache, wipe data/factory reset a load of time randomly but it still didnt work PLEASEE HELP IM A STUPID NOOB AND I only got this new!!!
you didnt flash anything so it should still be fine, just without your data,you can get into recovery or download mode why not flash a new rom in odin?,your phone is still fine.look for a stock rom to revert
Your phone will take 5 to 10 minutes to boot after clearing cache, so if you are sure your mobile doesn't boot after 10 minutes then you have two alternatives .
1. Boot into cwm, connect your mobile to PC, mount your sdcard via cwm, copy the custom rom and flash it.
2. Download a stock from and flash it via odin
#*posted on the move *#
Flash again
1. Download a new stock rom from samfirmware.com
2. Save it to your pc
3. Get odin 1.85
4. Put your phone in download mode make sure battery is at least 50%, by holding down volume down, power and home key
5. Once in download mode press volume up to continue
6. Now on your pc you installed open odin 1.85 open the program
7. Connect the usb cable to phone first then to your pc.
8. Wait for the first box in odin to come yellow
9. Once it does click on 'pda' and find the stock firmware you downloaded do remember do not extract it nothing.
10. Once you have selected the file it will appear in the PDA section sometimes depending on the stock rom there might be 3 files so you may need to put the other files in the section above and below PDA so make sure you read this before anything.
11. Once done click start
Once the box turns green it will say passed and your phone will reboot and you will have successfully installed the original firmware back again.
Anything you dont understand reply back.
i am amazed how can u miss one of the sticky that says
[READ THIS] Got a Boot Loop? Don't post a New Thread!
http://forum.xda-developers.com/showthread.php?t=1108499
Slow N Stupid said:
i am amazed how can u miss one of the sticky that says
[READ THIS] Got a Boot Loop? Don't post a New Thread!
http://forum.xda-developers.com/showthread.php?t=1108499
Click to expand...
Click to collapse
Dont be sadly its the norm .
jje
Hi guys
I have just flashed Omega v8.1 to my phone and reflashed CWM touch, rebooted into recovery and now my phone won't boot. It turns on and just displays the "Samsung Galaxy S3" screen. I have tried flashing via the Galaxy s 3 toolkit but this requires USB debugging to be enabled. It looks as though it is not enabled as the toolkit does not recognise my phone.. The only thing I can do is boot it into download mode.
Any clues??
Thanks
If you can go on download mode, then flash stock firmware via odin.
Sent from my GT-I9300 using xda premium
Firstly your phone is fine, it can be easily fixed one way or another.
Can you still boot into recovery?
If not, reflash recovery using ODIN via Download mode
Once you have access to the recovery, try wiping the following:
Data/Factory reset
Cache
Dalvik Cache
Format /system (probably not required but just in case)
And then reflash the omega ROM, making sure it is not corrupt; maybe redownload/check MD5 sum to be sure.
If, for whatever reason you are still having problems with the phone not booting into Android, I would try flashing a different ROM for the time being.
Also, you posted this in the wrong section
Just flash the stock rom?
Yep bricked phone isn't really a problem, unless it's hardware related.
Sent from my GT-I9300 using xda premium
prank1 said:
Firstly your phone is fine, it can be easily fixed one way or another.
Can you still boot into recovery?
If not, reflash recovery using ODIN via Download mode
Once you have access to the recovery, try wiping the following:
Data/Factory reset
Cache
Dalvik Cache
Format /system (probably not required but just in case)
And then reflash the omega ROM, making sure it is not corrupt; maybe redownload/check MD5 sum to be sure.
Also, you posted this in the wrong section
Click to expand...
Click to collapse
This right method, some times data ****ed up, so must wipe cache
Sent from my GT-I9300 using Tapatalk 2
Ive tried flashing stock ROM via ODIN through the toolkit but this requires USB debugging mode. The issue is not with Omega as I was able to use my phone after flashing, I think the CWM flash didnt work properly.
How else can I flash via ODIN, the toolkit is the only way I know.
Thanks for the comments guys...
brianwilkie76 said:
Ive tried flashing stock ROM via ODIN through the toolkit but this requires USB debugging mode. The issue is not with Omega as I was able to use my phone after flashing, I think the CWM flash didnt work properly.
How else can I flash via ODIN, the toolkit is the only way I know.
Thanks for the comments guys...
Click to expand...
Click to collapse
No it needs download mode.
Gesendet von meinem GT-I9300 mit Tapatalk 2
reflash cwm and see
Sent from my GT-I9300 using xda premium
brianwilkie76 said:
Ive tried flashing stock ROM via ODIN through the toolkit but this requires USB debugging mode. The issue is not with Omega as I was able to use my phone after flashing, I think the CWM flash didnt work properly.
How else can I flash via ODIN, the toolkit is the only way I know.
Thanks for the comments guys...
Click to expand...
Click to collapse
I d say, simply get odin separately, then re-create the same settings as when the toolkit does it.
It really is very simple once you ve done it once or twice Don t panic and take the time to make sure the right boxes are checked and double-triple check then reboot in Download mode, plug it in then gogo !
Tectas said:
No it needs download mode.
Gesendet von meinem GT-I9300 mit Tapatalk 2
Click to expand...
Click to collapse
If I select flash via odin in the toolkit (option 8), it says make sure that USB debugging is enabled... If i try and continue it just waits for usb debugging and does not flash.
brianwilkie76 said:
Ive tried flashing stock ROM via ODIN through the toolkit but this requires USB debugging mode. The issue is not with Omega as I was able to use my phone after flashing, I think the CWM flash didnt work properly.
How else can I flash via ODIN, the toolkit is the only way I know.
Thanks for the comments guys...
Click to expand...
Click to collapse
y u r usb debugging is disable? u have to enable it before doing any thing
Sent from my GT-I9300 using xda premium
brianwilkie76 said:
Ive tried flashing stock ROM via ODIN through the toolkit but this requires USB debugging mode. The issue is not with Omega as I was able to use my phone after flashing, I think the CWM flash didnt work properly.
How else can I flash via ODIN, the toolkit is the only way I know.
Thanks for the comments guys...
Click to expand...
Click to collapse
You can use odin without the toolkit for the meantime, just run it and put your phone on downlod mode
Sent from my GT-I9300 using xda premium
hisee said:
y u r usb debugging is disable? u have to enable it before doing any thing
Sent from my GT-I9300 using xda premium
Click to expand...
Click to collapse
It's always disabled after ROM flash and I keep forgetting to re enable it..
brianwilkie76 said:
If I select flash via odin in the toolkit (option 8), it says make sure that USB debugging is enabled... If i try and continue it just waits for usb debugging and does not flash.
Click to expand...
Click to collapse
Ok, sry, then the toolkit reboots your device first to download mode via adb, take the already given advice to use Odin itself, just download it put the Rom tar (or tar.md5) into pda, make sure that only auto reboot and reset time is checked, reboot to download mode continue by pressing up, plugin the cable and press the start button at Odin.
Gesendet von meinem GT-I9300 mit Tapatalk 2
Forget running the toolkit, forget USB debugging mode. You do not need it for now.
And there is no need to download or setup ODIN or anything like that.
Just go to folder/directory where you installed the toolkit (usually C:\Samsung Galaxy S3 ToolKit) and look for the file called 'Odin3_v3.07' or 'Odin3_v3.04' or whatever version you find. Then run it; tada, ODIN is running now!
Now, put your phone in download mode. To do this, hold VOL DOWN and HOME and POWER buttons together and let go when you see the 'Samsung Galaxy S III' logo come up.
Then it will load up a screen that says press VOL UP to continue (and enter download mode). Press it.
Now it should say 'Downloading do not turn off target!'
Connect your USB Cable and proceed to flash a new CWM recovery using ODIN
Then once you have flashed a new recovery, boot into it (VOL UP & HOME & POWER buttons together).
Then follow my instructions from my previous post.
prank1 said:
Firstly your phone is fine, it can be easily fixed one way or another.
Can you still boot into recovery?
If not, reflash recovery using ODIN via Download mode
Once you have access to the recovery, try wiping the following:
Data/Factory reset
Cache
Dalvik Cache
Format /system (probably not required but just in case)
And then reflash the omega ROM, making sure it is not corrupt; maybe redownload/check MD5 sum to be sure.
If, for whatever reason you are still having problems with the phone not booting into Android, I would try flashing a different ROM for the time being.
Click to expand...
Click to collapse
If you want to flash a stock ROM instead of CWM + Custom ROM then you can do that via ODIN as well.
heyy i am suffering with same problem
Hi i have galaxy s3
I was using Omega Rom happily since last month. But today i installed extended power menu and brightness fix mods from omega app. Then when the phone restarted it is stuck in boot (Samsung)
I did everything what could i do:
Re-installed CF-Root many times
Re-installed kernal siyah again
But nothing is happening its still stucked on the boot screen & it vibrates 2 3 times but the screen remains still on samsung logo
Guys plz tell me what should i do.
themude said:
heyy i am suffering with same problem
Hi i have galaxy s3
I was using Omega Rom happily since last month. But today i installed extended power menu and brightness fix mods from omega app. Then when the phone restarted it is stuck in boot (Samsung)
I did everything what could i do:
Re-installed CF-Root many times
Re-installed kernal siyah again
But nothing is happening its still stucked on the boot screen & it vibrates 2 3 times but the screen remains still on samsung logo
Guys plz tell me what should i do.
Click to expand...
Click to collapse
Boot into custom recovery (VOL UP & HOME & POWER buttons together)
Then:
Data/Factory reset
Wipe Cache
Wipe Dalvik Cache
Reboot into Android and see if that has fixed it; if not, then go back to CWM recovery and do the following:
Data/Factory reset
Wipe Cache
Wipe Dalvik Cache
Format /system (probably not required but just in case)
And then flash Omega ROM again
how? CMW is not opening the phone is only able to open in download mode nothing else. Its a fault with OMEGA 8.1 mods or maybe siyah beta kernal
how to start in recovery mode? If i press the 3 buttons it takes me to download mode
themude said:
how? CMW is not opening the phone is only able to open in download mode nothing else. Its a fault with OMEGA 8.1 mods or maybe siyah beta kernal
how to start in recovery mode? If i press the 3 buttons it takes me to download mode
Click to expand...
Click to collapse
http://www.youtube.com/watch?v=UxaVXJJdhhk
How to enter RECOVERY mode on the Samsung Galaxy S3
1) Make sure the phone is turned OFF (take out battery, wait 10 seconds, replace battery, make sure nothing appears on screen)
2) Press+Hold the VOL UP and HOME buttons, together
3) Now, whilst holding these two buttons together, press+hold the POWER button
4) Keep all of these buttons held down, don't let go even if you see the 'Samsung Galaxy S III' logo screen, ignore it and keep holding those three buttons down
5) Once you see the recovery screen, you can let go of the buttons and start using the recovery as you wish
How to enter DOWNLOAD mode on the Samsung Galaxy S3
Follow all the steps as above, except at step 2) press+hold VOL DOWN and HOME buttons together
Hello all
i tried flashing with odin mobile thing pro but i failed now when i boot up nothing comes up after the samsung logo. i can still use download and recovery mode (the recovery mode is from sasmung) my phone is rooted , had 2.3.3 on it and is an samsung galaxy s2 I9100 hope you guys can help me i was trying to update it to 2.3.6 can you guys help me with that too?
kristofer_gvenetadze said:
Hello all
i tried flashing with odin mobile thing pro but i failed now when i boot up nothing comes up after the samsung logo. i can still use download and recovery mode (the recovery mode is from sasmung) my phone is rooted , had 2.3.3 on it and is an samsung galaxy s2 I9100 hope you guys can help me i was trying to update it to 2.3.6 can you guys help me with that too?
Click to expand...
Click to collapse
boot to recovery mode and perform a factory reset. Reboot your phone
Your device should boot now , if the flashing process was error- free.
Swyped from my Galaxy SII
This is a soft brick ( don't panic , when i don't softbrick my phone at least once every couple of days , i feel that something is wrong with the phone )
Ok here is what to do
1) download siyah kernel.tar from http://www.gokhanmoral.com/public/files/siyahkernel/v3.0/Siyah-v3.3.3d.tar
2)download pc odin3 v1.85 ( google it)
3) get into download mode and flash siyah kernel
4) download a rom.zip and put on ur external sd card using a card reader to connect it to ur pc
5) boot into siyah kernel's recovery mode and install zip from sdcard then install the rom u want
It is recommended to wipe data and cache via recovery ( but dont do it if u were on 4.0.4 or were trying toi stall it)
Tefanym said:
This is a soft brick ( don't panic , when i don't softbrick my phone at least once every couple of days , i feel that something is wrong with the phone )
Ok here is what to do
1) download siyah kernel.tar from http://www.gokhanmoral.com/public/files/siyahkernel/v3.0/Siyah-v3.3.3d.tar
2)download pc odin3 v1.85 ( google it)
3) get into download mode and flash siyah kernel
4) download a rom.zip and put on ur external sd card using a card reader to connect it to ur pc
5) boot into siyah kernel's recovery mode and install zip from sdcard then install the rom u want
It is recommended to wipe data and cache via recovery ( but dont do it if u were on 4.0.4 or were trying toi stall it)
Click to expand...
Click to collapse
Thx !!!!
Tefanym said:
This is a soft brick ( don't panic , when i don't softbrick my phone at least once every couple of days , i feel that something is wrong with the phone )
Ok here is what to do
1) download siyah kernel.tar from http://www.gokhanmoral.com/public/files/siyahkernel/v3.0/Siyah-v3.3.3d.tar
2)download pc odin3 v1.85 ( google it)
3) get into download mode and flash siyah kernel
4) download a rom.zip and put on ur external sd card using a card reader to connect it to ur pc
5) boot into siyah kernel's recovery mode and install zip from sdcard then install the rom u want
It is recommended to wipe data and cache via recovery ( but dont do it if u were on 4.0.4 or were trying toi stall it)
Click to expand...
Click to collapse
thx again it worked !!!
kristofer_gvenetadze said:
thx again it worked !!!
Click to expand...
Click to collapse
Happy to hear that , just stay away from ICS 4.0.4
problem with the boot
heloo everyone i updated my samsung galaxys3 (SHVE210S) using odin(ICS to JELLYBEAN) but after the installation odin says SUCESS but my phone is not working :/ phone is starting but stuck in a moment after the welcome sound can plzzz anyone can help me how to resolve this problem, is it a problem in the firmware ????
not going after samsung logo
Tried rooting my s2 using odin. went into download mode then connected the phone. and clicked start. according to the instructions for rooting from youtube , it said the phone would restart after it said PASS on Odin. After it showed PASS it didnt restart even after a very longtime. so i disconnected.
Now i get the samsung logo with a triangle below. I m able to go to download mode.
Pls help guys
Ok there, guys.
Before I start, yes I'm an idiot, yes I'm a huge noob, no I don't know what I'm doing.
Basically, I have a SGS2 and I was trying to install Cyanogenmod 10.1.
I used Heimdall to (flash?) install ClockworkMod Recovery and it worked.
I realised that I hadn't put the Cyanogenmod .zip on my phone before I installed CWM.
I got up to rebooting my phone so I could transfer the zip but after the Galaxy splash screen nothing happened.
The screen just stays black and doesn't do anything.
I can access Download and Recovery mode so that's good.
I only have access to a Mac at the moment so I have to use the Heimdall command line.
If anybody could help it would be great, thanks!
jubsticles said:
Ok there, guys.
Before I start, yes I'm an idiot, yes I'm a huge noob, no I don't know what I'm doing.
Basically, I have a SGS2 and I was trying to install Cyanogenmod 10.1.
I used Heimdall to (flash?) install ClockworkMod Recovery and it worked.
I realised that I hadn't put the Cyanogenmod .zip on my phone before I installed CWM.
I got up to rebooting my phone so I could transfer the zip but after the Galaxy splash screen nothing happened.
The screen just stays black and doesn't do anything.
I can access Download and Recovery mode so that's good.
I only have access to a Mac at the moment so I have to use the Heimdall command line.
If anybody could help it would be great, thanks!
Click to expand...
Click to collapse
Put your forgotten .zip on an sd card put it in your phone. Boot to recovery and install. Then do full wipe and you should be good to go.
LSD Powered Time Machine.
gaosphappy said:
Put your forgotten .zip on an sd card put it in your phone. Boot to recovery and install. Then do full wipe and you should be good to go.
LSD Powered Time Machine.
Click to expand...
Click to collapse
How can I access my phone's storage through recovery/download mode?
Thanks for the reply, by the way.
Edit: Oops, sorry. Didn't read your reply correctly. Unfortunately I don't have a SD card. Is there a way I can restore my phone COMPLETELY to stock?
jubsticles said:
How can I access my phone's storage through recovery/download mode?
Thanks for the reply, by the way.
Edit: Oops, sorry. Didn't read your reply correctly. Unfortunately I don't have a SD card. Is there a way I can restore my phone COMPLETELY to stock?
Click to expand...
Click to collapse
Flash a stock rom and start from scratch. Get stock rom file from xda or sammobile (NOT A 4.0.4 ics rom tho.) flash via odin/Heimdall in download mode. it will boot up when done turn it off and reboot to recovery and do full wipe. redo your flash with missing .zip.
good luck
gaosphappy said:
Flash a stock rom and start from scratch. Get stock rom file from xda or (NOT A 4.0.4 ics rom tho.) flash via odin/Heimdall in download mode. it will boot up when done turn it off and reboot to recovery and do full wipe. redo your flash with missing .zip.
good luck
Click to expand...
Click to collapse
I flashed a 4.1.2 stock rom onto my phone but it still doesn't work.
I flashed the phone, it automatically rebooted, when the Samsung logo came up I took out the battery, went to recovery mode, wiped cache and full wipe, hit reboot and now it just stays on the Samsung logo, pulsing blue and what not.
I also did the same thing and instead of taking out the battery I just left it in there after the first reboot and the same thing happened.
How can I fix this?
Hum....I9100?
flash lsj (only phone, code abd csc).
Sent from the little guy
Hey,
I have since become a S3 ... I have rooted it and wanted to play another Rome.
First I flashed my Carbon ... that was wonderful, but I had no wifi. Then I tried another Rom (with aroma installer). When I had WiFi, but since I have the menu did not like it and it was me too many Samsung Apps.
Now I have flashed me the Resurrection Remix, but the S3 boots constantly new to the CWM.
The same I have with CM11.
What am I doing wrong please?
lolamarcel said:
Hey,
I have since become a S3 ... I have rooted it and wanted to play another Rome.
First I flashed my Carbon ... that was wonderful, but I had no wifi. Then I tried another Rom (with aroma installer). When I had WiFi, but since I have the menu did not like it and it was me too many Samsung Apps.
Now I have flashed me the Resurrection Remix, but the S3 boots constantly new to the CWM.
The same I have with CM11.
What am I doing wrong please?
Click to expand...
Click to collapse
You need to install exactly like below don't miss any steps
-Installation-
1.- Wipe data / factory reset (mandatory if you coming from STOCK OR 4.2.X version or another ROM)
2.- Install the Main ROM
3- install gapps
4.- When you're back on recovery go to Advanced
5.- Wipe Dalvik Cache
6.- Fix Permissions
7.- Wipe Cache Partition
8.- Reboot
If it still not working flash TWRP recovery and use that to flash the rom
Hey,
I just did it. Then came the Samsung logo, phone restarts and I'm back in the CWM.
Have just flashed TWRP reboot (via CWM) Recovery and but still have CWM.
Grrrrrr ...... what for now
Better download official firmware from Sammobile and install thru Odin. Then Root and carry on with your favorite custom rom.
Yes I agree with KSKHH if problem still there return to stock with odin and start again..
tallman43 said:
Yes I agree with KSKHH if problem still there return to stock with odin and start again..
Click to expand...
Click to collapse
How are you doing? Your phone is working now?
Hey,
so suck an official firmware and flash it with Odin ... then the CWM away again?
If I then use the rooten begin I play me but come back on automatically, or not?
lolamarcel said:
Hey,
so suck an official firmware and flash it with Odin ... then the CWM away again?
If I then use the rooten begin I play me but come back on automatically, or not?
Click to expand...
Click to collapse
Steps:
Install ORIGIANAL firmware via ODIN
Don't need to root
INSTALL CUSTOM RECOVERY
Copy desired ROM into memory card (or intrernal, if dont have memory card)
Wipe all
Install
Profit
Hey,
I have now taken me this firmware:
I9300XXUGML2_I9300DTMGML2_I9300BOUGMK3_HOME.tar
Odin started, specified in the PDA tar file, made my S3 in the download mode, USB cable ran ... it was detected and was also flashed. Now I sit for at least 10 minutes and nothing happens.
The Samsung logo always changes its color and the LED on the top left light blue.
lolamarcel said:
Hey,
I have now taken me this firmware:
I9300XXUGML2_I9300DTMGML2_I9300BOUGMK3_HOME.tar
Odin started, specified in the PDA tar file, made my S3 in the download mode, USB cable ran ... it was detected and was also flashed. Now I sit for at least 10 minutes and nothing happens.
The Samsung logo always changes its color and the LED on the top left light blue.
Click to expand...
Click to collapse
Boot into recovery then factory reset..
hey,
exactly these thoughts I had just as well.
Meanwhile, I have written this text did something on the screen ... the phone goes again.
Thanks to all
So now just flash a recovery and then flash as usual custom of Rome?
Edit:
GT-I9300
Android 4.3
Baseband I9300BOUGMK3
Kernel: 3.0.31-2303192 [email protected]#1 FriDec 13 21:55:31 KST2013
Build: JSS15J.I9300XXUGML2
Edit2:
Hey,
so, now I have successfully flashed TWRP and tested.
Now I'll try to flash CM11 ... hopefully it starts this time also
Edit 3:
so, now it has worked wonderfully.
Thanks again for the help