Hello, need to root ZTE V790. Please help. Thank you very much.
Rooting ZTE V790
After series of serching, I was able to root zte V790 through the help of a chinese forum:
bbs.hiapk.com/thread-4620917-1-1.html :good:
Tools to Download
1. Download drivers.
mediafire.com/?f7h1f7i7skggmtg
2. Download V790 Root Tool
pan.baidu.com/share/link?shareid=379900&uk=255085915
DISCLAIMER: I AM NOT RESPONSIBLE IF YOU BRICK / RUIN YOUR PHONE IN ANY WAY. THE FOLLOWING ARE THE STEPS I HAVE FOLLOWED TO SUCCESSFULLY ROOT MY ZTE V790
Procedures:
1.Extract and Install all drivers in the computer.
2.Turn Off the phone and take the sim card out.
3.Turn on the phone. Ensure that the battery is not less than 50%.
4.Plug the usb cable from phone to computer. Ensure that the phone USB debugging is ticked.(Home>Settings>Developer options>USB Debugging). Phone USB computer connection should be "connected as an installer", this can be done by unticking Media device MTP or Camera PTP.
5.Run the Root Tool.exe. (Note that this is in chinese but there are few english words just Follow on screen prompts. It will automatically detect the phone if the drivers are installed correctly)
6.Phone will restart after the process is completed. (Whole process take about 2 to 5 minutes)
7.Once the phone has turned on, You can now see the Superuser icon and Root explorer. Congratulations, you are now rooted.:highfive:
If unsuccessful, repeat all the steps.
Hit Thanks.
astigjaps said:
After series of serching, I was able to root zte V790 through the help of a chinese forum:
bbs.hiapk.com/thread-4620917-1-1.html :good:
Tools to Download
1. Download drivers.
mediafire.com/?f7h1f7i7skggmtg
2. Download V790 Root Tool
pan.baidu.com/share/link?shareid=379900&uk=255085915
DISCLAIMER: I AM NOT RESPONSIBLE IF YOU BRICK / RUIN YOUR PHONE IN ANY WAY. THE FOLLOWING ARE THE STEPS I HAVE FOLLOWED TO SUCCESSFULLY ROOT MY ZTE V790
Procedures:
1.Extract and Install all drivers in the computer.
2.Turn Off the phone and take the sim card out.
3.Turn on the phone. Ensure that the battery is not less than 50%.
4.Plug the usb cable from phone to computer. Ensure that the phone USB debugging is ticked.(Home>Settings>Developer options>USB Debugging). Phone USB computer connection should be "connected as an installer", this can be done by unticking Media device MTP or Camera PTP.
5.Run the Root Tool.exe. (Note that this is in chinese but there are few english words just Follow on screen prompts. It will automatically detect the phone if the drivers are installed correctly)
6.Phone will restart after the process is completed. (Whole process take about 2 to 5 minutes)
7.Once the phone has turned on, You can now see the Superuser icon and Root explorer. Congratulations, you are now rooted.:highfive:
If unsuccessful, repeat all the steps.
Hit Thanks.
Click to expand...
Click to collapse
Wow, thanks.. Finally rooted mine. You're the man :highfive:
Astig ka nga!
help
jessiegoran said:
Wow, thanks.. Finally rooted mine. You're the man :highfive:
Astig ka nga!
Click to expand...
Click to collapse
tol bat ayaw gumana saakin ? na stock ako sa zte boot logo
Help
Hi every one, I bought ZTE V790 Movistar Motion, (in Venezuela) I've rooted and Install a Vietname Rom, Now my Phone Is (Model Number: V8403 Based version Viettel_V8403B01 Build Number VIETTEL_V8403V1.0.0B09) and it's a stupid Rom, I've tried to install another rom from Russian Site but my phone refuse it!!! I want my Phone Back I Don't want this Vietname Version Pleas HELP
Oh yes!!!
thanks for this tutorial bro.. it worked for me!!
now my phone is rooted!!
you're great dude..
thanks a lot..
BTW.. if i managed to root my phone is there any way i can unlock the SIM slots?
SIM2 is already unlocked but SIM1 slot is still locked.
thanks again dude..
it says adb is out of date...
Some tips:
1) If the device is not recognised in the root tool. Install JoinMe as well, it contains another USB driver.
2) If you are stuck in ZTE logo or "waiting for device", just enable an option in Windows Update to automatically search and install device drivers. Windows will ask this when you select 'Trouble shooting' if installing drivers fails.
3) You may need to install USB drivers in total three times from: ZTE USB driver, JoinMe and Windows Update.
ZTE 790 Root
My ZTE v790 still gets stuck in ZTE Logo.
Android driver still missing after selecting auto update drivers.
I'm using XP and it's online.
I reinstalled both the ZTE Drivers and Join ME.
Any other suggestions?
English version of ROM for v90
Hello
is there any English version ROM for v790? I have bought zte v790, android 2.3.6 and unfortunately there is plenty of useless applications in Chinese, as well as Chinese system communicates and the worst thing is that the browser is very difficult to get Google or any proper websites like facebook for example. I can do root and thank you for the instruction but then i will need to install ROM in english version. Is there any way to get English version for v790?
Thank you!
Mk
Heya,
I'm looking for android 4.0 rom for this phone too. Any know where i can find one? I've found Russian one but that's far from what I'm looking for.
Thanks
kptbomba said:
Heya,
I'm looking for android 4.0 rom for this phone too. Any know where i can find one? I've found Russian one but that's far from what I'm looking for.
Thanks
Click to expand...
Click to collapse
every rom has every language, just change it through the settings. i didn't find it very hard to guess where to click as there are icons and the language list has "english" in english. funny that.
Found the fix to getting stuck at ZTE Logo!
Hi guys,
Like Furiku, i kept getting stuck at the ZTE Logo when attempting the steps from the OP.
After doing some research, i found another spanish-language guide that included the Moto Helper drivers. Installing the drivers did the trick.
As i am a new user and cannot yet post links, please search for the file indicated below on google, install, and do the steps again. I'm using Windows 8 and there comes a point when it goes beyond the ZTE Logo to a green screen which looks pixelated, and i thought i might have ruined my phone. Gave me a 3-second heart attack. Then the Moto Helper drivers kicked in, and it rebooted, and now the SuperUser icon is there.
Please note that I am making the same disclaimer as the OP: Do this at your own risk. Follow instructions to the letter. We cannot be held responsible for issues that may lead to a damaged/bricked phone.
Google this file and DL: MotoHelper_2.1.32_Driver_5.4.0.exe
No go with Android 4
AzmoD3uS said:
Hi guys,
Like Furiku, i kept getting stuck at the ZTE Logo when attempting the steps from the OP.
After doing some research, i found another spanish-language guide that included the Moto Helper drivers. Installing the drivers did the trick.
As i am a new user and cannot yet post links, please search for the file indicated below on google, install, and do the steps again. I'm using Windows 8 and there comes a point when it goes beyond the ZTE Logo to a green screen which looks pixelated, and i thought i might have ruined my phone. Gave me a 3-second heart attack. Then the Moto Helper drivers kicked in, and it rebooted, and now the SuperUser icon is there.
Please note that I am making the same disclaimer as the OP: Do this at your own risk. Follow instructions to the letter. We cannot be held responsible for issues that may lead to a damaged/bricked phone.
Google this file and DL: MotoHelper_2.1.32_Driver_5.4.0.exe
Click to expand...
Click to collapse
I've installed all the drivers. On the English words displayed (after being told to press any key & doing so), I get "fastboot error: protocol fault (no status)" & "< waiting for device >" with the phone's display stuck on the ZTE logo. I think that the problem is that my phone uses Android 4 (Jelly Bean) whereas other phones successfully rooted are using Android 2 (Gingerbread). Any ideas?
astigjaps said:
After series of serching, I was able to root zte V790 through the help of a chinese forum:
bbs.hiapk.com/thread-4620917-1-1.html :good:
Tools to Download
1. Download drivers.
mediafire.com/?f7h1f7i7skggmtg
2. Download V790 Root Tool
pan.baidu.com/share/link?shareid=379900&uk=255085915
DISCLAIMER: I AM NOT RESPONSIBLE IF YOU BRICK / RUIN YOUR PHONE IN ANY WAY. THE FOLLOWING ARE THE STEPS I HAVE FOLLOWED TO SUCCESSFULLY ROOT MY ZTE V790
Procedures:
1.Extract and Install all drivers in the computer.
2.Turn Off the phone and take the sim card out.
3.Turn on the phone. Ensure that the battery is not less than 50%.
4.Plug the usb cable from phone to computer. Ensure that the phone USB debugging is ticked.(Home>Settings>Developer options>USB Debugging). Phone USB computer connection should be "connected as an installer", this can be done by unticking Media device MTP or Camera PTP.
5.Run the Root Tool.exe. (Note that this is in chinese but there are few english words just Follow on screen prompts. It will automatically detect the phone if the drivers are installed correctly)
6.Phone will restart after the process is completed. (Whole process take about 2 to 5 minutes)
7.Once the phone has turned on, You can now see the Superuser icon and Root explorer. Congratulations, you are now rooted.:highfive:
If unsuccessful, repeat all the steps.
Hit Thanks.
Click to expand...
Click to collapse
jessiegoran said:
Wow, thanks.. Finally rooted mine. You're the man :highfive:
Astig ka nga!
Click to expand...
Click to collapse
How do you install the CFW????
Please help
Thanks
Is there any custom ROM for this phone?
Why when I plug jt my computer it says it's a V790 when it's a t2 lite
Related
hi all,
i need root for Alcatel one touch 918D. anybody an idea?
cu
How to root Alcatel 918D "Blaze Glory"
1. Install drivers
2. Install Android SDK
3. Make sure that USB-Debugging ist activated on your device
3. Start Dalvik Debug Monitor and make sure that your device is connected
4. Start SuperOneClick 2.3.3.
5. Voila! :-D
CU
EJ
So easy?
I'll try it...
p.s.
Where kan I find Dalvik debug monitor to download?
After many unsuccessful attempts (Gingerbreak, other SOC-Versions) someone in a forum from the philippines told me this way and for me it worked perfect!
The secret was to keep the device connected to DDM! Without that SOC freezes...
CU
EJ
h**p://s14.directupload.net/file/d/2794/biea5dsy_png.htm
EJ_the_DJ said:
1. Install drivers
...EJ
Click to expand...
Click to collapse
Which drivers?
I have no driver for Windows7...?
immerzu said:
Which drivers?
I have no driver for Windows7...?
Click to expand...
Click to collapse
Install "PDANet" on your PC with generic drivers. After that you should find an "Android ADB Phone" on your PC after plug-in the device.
Where can I find the Dalvik debug monitor?
If you installed the SDK you'll find it ..\Android\android-sdk\tools
Use the ddms.bat
Thanks, I've found.
But now he stuck at step 7 (Superoneclick).
any news about the root guys?
and i want to ask you a favore...
i know that some for most of you the steps to follow about the root operation,seems common and easy,but pls not forget that some of us,older than you,we have problem to "follow" you!!
i know that maybe i ask to much,but pls try to write the steps as simple as possible...
thank you very much
p.s you are the best
immerzu said:
Thanks, I've found.
But now he stuck at step 7 (Superoneclick).
Click to expand...
Click to collapse
i have the same problem with you
any solution pls?????
thank you!!!
any news???????
is there any other way to roor?
like un update zip file that we can run fron recovery mode?
pls..help
come on guys!
a little of help pls!!!!
something new?
immerzu said:
something new?
Click to expand...
Click to collapse
nothing at all!!
i do everithing that the other guys did.....but nothing.
soc stucks at step 7...
i have tried in 3 different pc....nothing
....maybe is because my firmware is different from theirs......
v23AAG0 greece
the guy that i have told has v23AAE0 germany
we must find another way to root....soc does not work at least for me!!
Firmware:
2.3.5
Build-Number:
v23AAE0
nothing to make. Tried on two PC.
something must be different
How to root OT918
Download this: ht tp: //w ww. unlockroot. com / index .htm
(sorry, i still can't post a link since i'm new. just remove the spaces on the posted link above)
1. Install the unlock root in your PC.
2. Enable USB Debugging mode on your device.
3. Connect your device to your PC using a USB cable.
4. Install the driver from the application shortcut menu under "Programs" on your PC.
5. Run the Unlock Root application.
6. Choose your device from the list of autodetected devices.
7. Click the Root button to start the rooting process.
8. Wait for it to complete the installation, after which you’ll be greeted with a message saying your device has been successfully rooted.
9. After the rooting process, simply reboot your device for the changes to take effect.
To check if you successfully rooted your device, just look if the Superuser app was installed.
Hope this help, tried and tested on windows 7 with my OT918
jhezsie20 said:
Download this: ht tp: //w ww. unlockroot. com / index .htm
(sorry, i still can't post a link since i'm new. just remove the spaces on the posted link above)
1. Install the unlock root in your PC.
2. Enable USB Debugging mode on your device.
3. Connect your device to your PC using a USB cable.
4. Install the driver from the application shortcut menu under "Programs" on your PC.
5. Run the Unlock Root application.
6. Choose your device from the list of autodetected devices.
7. Click the Root button to start the rooting process.
8. Wait for it to complete the installation, after which you’ll be greeted with a message saying your device has been successfully rooted.
9. After the rooting process, simply reboot your device for the changes to take effect.
To check if you successfully rooted your device, just look if the Superuser app was installed.
Hope this help, tried and tested on windows 7 with my OT918
Click to expand...
Click to collapse
the same ****
http://i.imgur.com/Uyivg.jpg
yeah....the same.....nothing works here.....
what the hell is going on with this phone??
The phone lives. :-D
immerzu said:
The phone lives. :-D
Click to expand...
Click to collapse
i dont know yet for how long its will be alive...
my hummer is ready for use
/dev/block/mtd
that is always the last script that i see in soc
in step 7,with the sdcard unmount
Hi there. I have this Android Phone from china called Dapeng i9800. Its a 6inch MTK 6575 using ICS 4.03. I wonder where can I find the original rom for this and if there is any tweaks for this phone. Sometimes sluggish when using it as it only has 512 ram.
Thanks in advance
i also have the same model! have you rooted this phone? i can't seem to find instructions on how to go about doing this. can you please point me the right way?
thanks
zaraki kenpachi said:
i also have the same model! have you rooted this phone? i can't seem to find instructions on how to go about doing this. can you please point me the right way?
thanks
Click to expand...
Click to collapse
I got the root from here
xxx.slatedroid.com/topic/33144-haipad-i9220-mtk6575-android-40/
1.Please download root file on
xxx.t-kstore.com/4.0root.rar
2.Go to*setting-developer options-click USB debugging
3.Connect the phone with computer,turn on usb device.
4.Click the file you download from the link TPSparkyRoot.bat*
5.Your phone will restart first time,after the phone start finish(until you see the unlock),click enter in the window of TPSparkyRoot.bat.
6.The phone will restart second time,still the same as first time we did.Then start third time,same as we did in last two*times.Click enter,then phone was rooted.
7.You will see two more app was installed in your phone,that mean root phone successfully.
thanks! that was very helpful information! i had some trouble getting windows to connect to my device. kept getting the error: device not found. i suppose it is because i didn't have the proper drivers for the device.
but it is surprisingly easier when done in linux. i just needed to mess around a little with the udev rules.
for the benefit of newbies like me, the instructions provided from that link provided by worldbreaker, i didn't completely follow them. you can choose to install your own superuser and root explorer apk here. in my case, i already installed the Superuser app from the play store even before the rooting process. i also installed Root Explorer separately from the rooting process as well. so no chinese apps for me
now what?
worldbreaker said:
I got the root from here
xxx.slatedroid.com/topic/33144-haipad-i9220-mtk6575-android-40/
1.Please download root file on
xxx.t-kstore.com/4.0root.rar
2.Go to*setting-developer options-click USB debugging
3.Connect the phone with computer,turn on usb device.
4.Click the file you download from the link TPSparkyRoot.bat*
5.Your phone will restart first time,after the phone start finish(until you see the unlock),click enter in the window of TPSparkyRoot.bat.
6.The phone will restart second time,still the same as first time we did.Then start third time,same as we did in last two*times.Click enter,then phone was rooted.
7.You will see two more app was installed in your phone,that mean root phone successfully.
Click to expand...
Click to collapse
anyone know how i can flash clockworkmod recovery on this phone? i can't seem to find any information about this.
Please give me a fresh link to this suggested link
worldbreaker said:
I got the root from here
xxx.slatedroid.com/topic/33144-haipad-i9220-mtk6575-android-40/
1.Please download root file on
xxx.t-kstore.com/4.0root.rar
2.Go to*setting-developer options-click USB debugging
3.Connect the phone with computer,turn on usb device.
4.Click the file you download from the link TPSparkyRoot.bat*
5.Your phone will restart first time,after the phone start finish(until you see the unlock),click enter in the window of TPSparkyRoot.bat.
6.The phone will restart second time,still the same as first time we did.Then start third time,same as we did in last two*times.Click enter,then phone was rooted.
7.You will see two more app was installed in your phone,that mean root phone successfully.
Click to expand...
Click to collapse
Hi everyone,
I'm trying to root my phone and this file xxx.t-kstore.com/4.0root.rar is no longer available. I hope that someone can plase give me a copy of it or at least let me know where to find it.
Thank you.
Dapeng i9800 firmware found but links dead! Nead russian help!
Hi, I'm from West-Germany and got into trubble:
First of all, I used A Dapeng I9800 for more than 2 years without any problems!
Then, I got my Winter-Blues and cleaned cache from recovery mode!
After that the device didn't boot, because it wanted a passwort to use the cache, which wasn't set. No prob so far!
The solution I found was, that I have to set back to factory default.
But I took off the battery while it was formatting.
Yes, shame on me, I wasn't patient(!) thats my fault!
Now, I've got two new problems:
Is the EMMC bricked?
My russian isn't good enough to enter this forum: china-iphone.ru
to ask these two guys:
BBV1962 http://forum.china-iphone.ru/member12688.html
and:
designed http://forum.china-iphone.ru/member201062.html
via PM, for a working link they posted for my device in their posts on this sides:
http://forum.china-iphone.ru/n9880-6-0-480x854-1-2ghz-android-4-0-3-2x3000-mah-t21999-120.html
http://forum.china-iphone.ru/n9880-6-0-480x854-1-2ghz-android-4-0-3-2x3000-mah-t21999-140.html.
The MTK6575-77 6" original firmware ROM below the posted picture is what I mean.
I hope, someone can get a link for me AND it is not worthless, because the EMMC is broken, as my own backup dosn't work.
Maybee you can get the info hww to flash back exactly, because I get an 4010 format error with the spflash tool.
Thanks a lot
Hello all,
I have googled, and searched forums high and low to no result so I thought i'd ask.
I recently purchased "KVD APOLLO ONE K6589 Quad-Core Android 4.2.1 WCDMA Smartphone w/ 5.5"
Im new so I can't post external links, however if you go to google or deal extreme and search, you'll find it easy enough.
The phone itself was next to nothing ($180) so even if its Unrootable, I'm not too fussy.
I would however prefer it rooted, I have read that you can basically use the MTK6577 rooting tool on the device?
Would this risk bricking the device.
I'v attempted to contact the manufacturer however to no avail! This is a rather new model so I know im being a tad impatient but if anyone can help then please do
Thanks guys
Potentional Tutorial
philipkroberts said:
Hello all,
I have googled, and searched forums high and low to no result so I thought i'd ask.
I recently purchased "KVD APOLLO ONE K6589 Quad-Core Android 4.2.1 WCDMA Smartphone w/ 5.5"
Im new so I can't post external links, however if you go to google or deal extreme and search, you'll find it easy enough.
The phone itself was next to nothing ($180) so even if its Unrootable, I'm not too fussy.
I would however prefer it rooted, I have read that you can basically use the MTK6577 rooting tool on the device?
Would this risk bricking the device.
I'v attempted to contact the manufacturer however to no avail! This is a rather new model so I know im being a tad impatient but if anyone can help then please do
Thanks guys
Click to expand...
Click to collapse
philipkroberts said:
Hello all,
I have googled, and searched forums high and low to no result so I thought i'd ask.
I recently purchased "KVD APOLLO ONE K6589 Quad-Core Android 4.2.1 WCDMA Smartphone w/ 5.5"
Im new so I can't post external links, however if you go to google or deal extreme and search, you'll find it easy enough.
The phone itself was next to nothing ($180) so even if its Unrootable, I'm not too fussy.
I would however prefer it rooted, I have read that you can basically use the MTK6577 rooting tool on the device?
Would this risk bricking the device.
I'v attempted to contact the manufacturer however to no avail! This is a rather new model so I know im being a tad impatient but if anyone can help then please do
Thanks guys
Click to expand...
Click to collapse
Also looks like im getting the Star N9589 just due to the more support available.
Anyhow until then, failing any answers from here, another chinese forum a spanish one and Yahoo answers I am going to go with the following method, If it dies, It dies this was my own fault for not doing enough research and at least it lets others know. I would send it back to DX But cba with postage fees and the hassle;
THIS IS DONE AT YOUR OWN RISK! -
APOLLO ONE - MTK 6589 K6589
Please note all tools and zip files mentioned I cant link to yet should you feel you want them please post in this thread and I will PM you, Gotta get my post count up first!
Guide by philipkroberts Twitter @philipkroberts
Revision 1 - People to be added to credits for leehed source, currently untested, concept only
Before anything try and boot into any form of recovery mode and backup if possible!
DISABLE UAC in WINDOWS 7
RIGHT CLICK RUN AS ADMIN ON ALL FILES
ALLOW NON TRUSTED DRIVER INSTALLATION (Google this if unsure)
On the phone install anububu on pc phone. - See what model it detects as and note it down.
Run MTK DROID TOOLS and connect phone see if drivers After a few seconds, the box should turn blue, and it should say "Apollo ONE or Other Name " besides it. The drivers are working.
If not try the other drivers in the drivers folder using device manager, there are many tutorials for this I cba typing one im so tired! and make sure you have the only trusted drivers thing turned off, if you constantly get unknown driver then your out of look and wil have to try and source some yourself.
Win7 (This method has not been tested by myself. Confirmation required.)
HOW TO MANUALLY INSTALL ANY DRIVERS IF NEEDED
a - Downloading This tool Called EASYBCD
b - Use it to restart your computer in advanced boot mode. (PRESSING F8 WHILST BOOTING UNTIL YOU GET THE OPTION FOR Disable signed driver enforcement)-Must be done everytime you wanna root a phone with this method.
c - Follow instructions and disable SDE.
d Manually install drivers, if above did not work (Yellow sign issue)
e Navigate to control panel - > Hardware and Sound - > Device Manager
f You should see a driver notice with a yellow warning sign next to it.
g Right click on it and choose "Update driver..".
h- Manually assign drivers, usually the choice furthest down.
i- In the window which should have appeared, navigate to the preload/Mt6590 folder and press OK.
j- If SDE is turned off, you should see a red warning window. This is normal, just accept the message prompted.
k- The drivers should now be successfully installed.
l - Once this is done open C:\Users\Hate\Desktop\Chinese Droid Rooting\MTKROOT TOOLS\Root_with_Restore_by_Bin4ry_v28\runme.bat Hope it ****ing works if so your rooted, If not try this next few steps, AGAIN at your own risk, no need to format just continue from here.
THE FOLLOWING STEPS ARE FOR THE STAR S5 - SAME PROCESSOR BUT NO GARUNTEE. DO NOT FOLLOW THESE STEPS UNLESS YOU ROOTED ANOTHER WAY AND NOW JUST WANT TO INSTALL A CWM
THE FOLLOWING STEPS ARE FOR THE STAR S5 - SAME PROCESSOR BUT NO GARUNTEE. DO NOT FOLLOW THESE STEPS UNLESS YOU ROOTED ANOTHER WAY AND NOW JUST WANT TO INSTALL A CWM
THE FOLLOWING STEPS ARE FOR THE STAR S5 - SAME PROCESSOR BUT NO GARUNTEE. DO NOT FOLLOW THESE STEPS UNLESS YOU ROOTED ANOTHER WAY AND NOW JUST WANT TO INSTALL A CWM
THE FOLLOWING STEPS ARE FOR THE STAR S5 - SAME PROCESSOR BUT NO GARUNTEE. DO NOT FOLLOW THESE STEPS UNLESS YOU ROOTED ANOTHER WAY AND NOW JUST WANT TO INSTALL A CWM
0 - Use PC to copy UPDATE-SuperSU-v.1.25.zip to the root of SD CARD, do not unpack just leave whole zip there.
1 - Turn off your phone, remove your battery. (Do not connect your phone to the computer yet!)
2 - Navigate to the "SP Flash Tool" folder, and run the tool.
3 - On the right side of the tool, there should be a button, iconed with a folder, named "Scatter-Loading". Click this.
4 - Navigate to the "Yulypis Recovery" folder, and double-click on the "Mt6589_Android_scatter-emmc.txt".
5 - You should be back at the SP Flash Tool start-screen, and there should have appeared a list of text and hex-codes.
6 - The "Recovery" line, should be ticked off, and preloader should be red.
7 - Now, click on the button named "Download", with a blue arrow on it. Press "YES" on the NOT ALL images has been correctly loaded warning.
8 - Connect your phone to a USB 2.0, with removed battery. The program should now work, and if drivers is set up correctly, the 0% will turn 100% and a green circle will appear in the middle of the screen. If your phone disconnects before the flashing tool is able to recognize your device, try putting the battery back into the phone before running SP Flash tool. Additionally, if this doesn't work, try using different drivers in the drivers folder
9 - Disconnect your K6589 from the computer when you see the green circle, insert the battery and boot the phone. Wait for it to get to the start screen.
11 - Installing SuperSU through Yulypis recovery
12 - Run "MtkDroidTools.exe" from the folder.
13 - Connect your device, and after a few seconds, information about your device should appear.
14 - Click on reboot, on the mtkDroidTools start-screen, and choose "..recovery".
15 - If recovery has been properly flashed, your device will now enter Yulypis recovery. Blue, with english text.
16 - Controllers: "Power = Enter, Initialize", "Volume down = Scrolling down". (Don't remember if volume up was bugged or not)
17 - Enter "Install zip from SDcard" - > Navigate to the earlier copied "UPDATE-SuperSU-v.1.25.zip and initialize it by pressing the power button.
18 - Follow the on-screen instructions, and it should be prompted to install after 1-2 more screens.
19 - Reboot the device by clicking on "+++++back+++++" and "Reboot now / Reboot Device".
Either way I am going to smash this in a week or so when the phone arrives from DX and will keep people update.
Peace
Please I want to buy this phone. Can you answer me a few doubts I have?
- How is the viewing angle? Cause i purchased a tablet from china and the angle is very bad.
- Has proximity sensor?
Are you ok with the phone?
thank you.
cabrote said:
Please I want to buy this phone. Can you answer me a few doubts I have?
- How is the viewing angle? Cause i purchased a tablet from china and the angle is very bad.
- Has proximity sensor?
Are you ok with the phone?
thank you.
Click to expand...
Click to collapse
I'm still awaiting the phone, hence why that guide is at your own risk.
However from what I have been told and gather that should root the phone no problems.
As for custom roms, I wouldn't even bother trying!
Once the phone gets here I will test my tutorial and re-write it into a more easy on the eyes fashion.
Thanks
http://www.fastcardtech.com/APOLLO-ONE-K6589?u=37825
They sell the phone, for an extra $3 they root before sending.
It cant be that hard, I'd love to know someone in that factory!
I'm looking for a link to download the full stock firmware for this device.
Anyone, please?
...or at least a firmware dump from a non-modified working phone.
One could use MTK Droid Tools and SPFlash to perform this task easily.
PM me for assistance if you need it.
Thank you.
well, i hope this will pass cause I am a noob here..
As an owner of this pretty much cheap and quite alright device I had hard time finding proper root method but in the end it was found..
Mine was already on 4.2.1 and the rest is as usual 1,5ghz dual core, mali 400 graphics, and apparently cortex a7 not a9 as on the box.. but who cares, right!?
so i got to the file (its actually based on crystal_root method from xda but some smart guy somewhere just made it work for 4.2 generic tablet ) I apologize if this si mentioned somewhere else, and I couldn't reply to crystal root board cause i am a noob, but I am sure some people will find this useful, that's all.
ok...you can chat here with me untill i got those 10 posts to upload link, you can google "Aigo M80E - JB 4.2.1 - help with rooting (killing cell standby)" or you can be a good soul and my first mate here and paste link
Cheers!
Hello,
I have the same model, and been looking for root.
Thanks.
MS!
prestigio 8.0 hd root (JB 4.2.1)
copy this file to sd card go to recovery and install
New firmware
New firmware available for our tablet:
PMP5588C_20140102_v1.0.42:
http://de05.dl.prestigio.com/Service_Files/TabletPC/PMP5588C/PMP5588C_20140102_v1.0.42.zip
1. New preinstalled applications
2. User agent profile for Android browser updated
3. APN/SPN files updated
4. Skype issue fixed
5. Video player issue fixed
6. Chrome browser bugs fixed
7. Sound Recorder issue fixed
8. Wi-Fi bugs fixed
9. Gallery issue fixed
10. System stability and speed improved
11. Other minor issues fixed
verification
Hello friends, i have problem with verification of modified or created own firmware on my PMP5588c duo, during instaling of this update from recovery, boot loader delet this instalation and displayes " validating error" Is possible break this validation? modified or choose other bootloader? sorry for multiple question. thanks for help David
Prestigio 5588c Rooting Issue
Hello to all.
I have a Prestigio 5588c and I had recently updated it to the latest firmware. I wanted to root this device, but it seems that the new update is not allowing the utoo-root-signed.zip to root it. It keeps failing. I was wondering if there is someone out there that is in the process of renewing the file so that it works on the most recent update from Prestigio.
Thank you in advance for your time and your great work regarding all things that are Android
Az
Root for PMP5588c_Duo
AzahTabor said:
Hello to all.
I have a Prestigio 5588c and I had recently updated it to the latest firmware. I wanted to root this device, but it seems that the new update is not allowing the utoo-root-signed.zip to root it. It keeps failing. I was wondering if there is someone out there that is in the process of renewing the file so that it works on the most recent update from Prestigio.
Thank you in advance for your time and your great work regarding all things that are Android
Az
Click to expand...
Click to collapse
Hello all,
I have the same PMP5588c_Duo device (4.2.1 stock Build PMP5588C.20131231.1.0.42) and managed to easily root it using Kingo root (kingoapp.com). It's a straighforward process:
download the app and install it on your PC
enable USB Debugging from the Developer options on the tablet
start the app on the PC
connect the table and PC with a microUSB cable
do not enable anything else on the tablet (like SD card access)
wait for Kingo to detect it
it will automatically download and install USB drivers to your PC and show a ROOT button
click the ROOT button, wait for 2-3 minutes, it could take up to 10min so be patient
the device will automatically reboot after the root has been applied
at which point disconnect the device
after the restart check for the SuperUser app, it will automatically install it
Have fun.
Z.
Zapryanov said:
Hello all,
I have the same PMP5588c_Duo device (4.2.1 stock Build PMP5588C.20131231.1.0.42) and managed to easily root it using Kingo root (kingoapp.com). It's a straighforward process:
download the app and install it on your PC
enable USB Debugging from the Developer options on the tablet
start the app on the PC
connect the table and PC with a microUSB cable
do not enable anything else on the tablet (like SD card access)
wait for Kingo to detect it
it will automatically download and install USB drivers to your PC and show a ROOT button
click the ROOT button, wait for 2-3 minutes, it could take up to 10min so be patient
the device will automatically reboot after the root has been applied
at which point disconnect the device
after the restart check for the SuperUser app, it will automatically install it
Have fun.
Z.
Click to expand...
Click to collapse
hey Z.
thank you for the guidance.. testing it now so will update shortly.. although the program thought I had a samsung note lol
ok, this is an update.. seems the program did not want to root my tablet. when I started it again, it classed it as a google device, but said connection failed due to cable instability.. guess I will have to try another way
double update... after leaving it for a few days, it seems to have wanted to work.. woohoo. thanks Z for the info
help with prestigio multipad 8.0 HD !!!
Welcome. I have a problem with this tablet.
Tablet died after a crash. There is no option to enter a Power + vol +
also does not move with the micro SD card from the system manufacturer Charges start-up screen and that's it. When connected to a PC saw it as m3-chip.
In total, I found drivers in Device Manager I did update the driver for the M3-chip and now the tablet is listed in my device manager as libusb- win 32 device. I found a program that detects such a connected tablet. The program is Amlogic Image Burning Tool v.1.6.2.2. For the time being this my progress stopped. I was trying to upload with this software firmware downloaded from the manufacturer's website dedicated for this device, but I get the message "find no upgrade" and do not know what to do. Can someone help me ??? I'm not an expert, and the above step I got reading the various forums. To my eye it looks as if they fell bootloader, but thanks to the above program to see the tablet (or rather its processor) and now combines where to download a bootloader to throw it out there and then be able to upload the system such as the sd card. Or is there some other program or a way to restore the dead to life my tablet ??? Can you help ???
1. Turn off the tablet (hold the power button and count to 12
2. Insert prepared SD card https://yadi.sk/d/_6VITNSbhKPyi
3. Press and hold the "Vol +", press "Power ON" for 2 sec.
4. Release all buttons and wait for boot TWRP (about 10 seconds)
5. In TWRP select Install -> update.zip
6. Reboot tablet
testatura said:
well, i hope this will pass cause I am a noob here..
As an owner of this pretty much cheap and quite alright device I had hard time finding proper root method but in the end it was found..
Mine was already on 4.2.1 and the rest is as usual 1,5ghz dual core, mali 400 graphics, and apparently cortex a7 not a9 as on the box.. but who cares, right!?
so i got to the file (its actually based on crystal_root method from xda but some smart guy somewhere just made it work for 4.2 generic tablet ) I apologize if this si mentioned somewhere else, and I couldn't reply to crystal root board cause i am a noob, but I am sure some people will find this useful, that's all.
ok...you can chat here with me untill i got those 10 posts to upload link, you can google "Aigo M80E - JB 4.2.1 - help with rooting (killing cell standby)" or you can be a good soul and my first mate here and paste link
Cheers!
Click to expand...
Click to collapse
Sorry Dude but it doesnt work ..... while updating abort... i tryed with all known firmware from the company ... kingoRoot KingRoot and also OneKlickRoot doesn´t work too. I´m Sad about that...
regards Michael
Hi, i've bricked my phone...someone knows how to unbrick.?
luisfernandoo.nunezfranco said:
Hi, i've bricked my phone...someone knows how to unbrick.?
Click to expand...
Click to collapse
Without any further details, it's going to be difficult to help. It's pretty hard to do so..... What did you do to brick it? Can you get into recovery. Do you have a custom rom? Provide some more details & someone might be able to help you
mightymaki said:
Without any further details, it's going to be difficult to help. It's pretty hard to do so..... What did you do to brick it? Can you get into recovery. Do you have a custom rom? Provide some more details & someone might be able to help you
Click to expand...
Click to collapse
>Hi Friend, i would appreciate yor help, my Nubua Z7 max is bricked after flashing the new(from needrom site) 5.0 stock rom and reflashing the original kitkat stock rom.
I need to repartition the phone storage , when i boot it appears only 4.0 Gbyte storage for programs , but no internal storage.
How can i repartition the internal storage?
Thank you
Simonis said:
>Hi Friend, i would appreciate yor help, my Nubua Z7 max is bricked after flashing the new(from needrom site) 5.0 stock rom and reflashing the original kitkat stock rom.
I need to repartition the phone storage , when i boot it appears only 4.0 Gbyte storage for programs , but no internal storage.
How can i repartition the internal storage?
Thank you
Click to expand...
Click to collapse
There are some instructions on the Z7 mini thread here on XDA. Have a search & follow the instructions
Unbrick Z7 max
mightymaki said:
There are some instructions on the Z7 mini thread here on XDA. Have a search & follow the instructions
Click to expand...
Click to collapse
Thank you but i did not find anything relevant by searching
[email protected] said:
Thank you but i did not find anything relevant by searching
Click to expand...
Click to collapse
You can follow this thread: http://www.androidiani.com/forum/zte-nubia-z7/446548-guida-di-unbrick-z7-max-mini.html
use google translate.
I am going to post a guide in English in about 2 hours. I have bricked mine and I followed the procedure from androidiani.
Guide to unbrick ZTE Nubia Z7 Mini
I have done this procedure on my device without any problem after a repartition failure, but I am not responsible about anything happens to your device (which is already bricked...)
The source is http://www.androidiani.com/forum/zte-nubia-z7/446548-guida-di-unbrick-z7-max-mini-27.html
1) We disable driver signature verification for windows.
- Windows XP https://mega.co.nz/#!30I1yLRD!kLblCqP9_LmiOXjpfzGbFL7m2zqAqKqZ8ciPFWMBDB0
- Windows 7 http://www.sabrent.com/support/knowledgebase.php?article=14
- Windows 8 http://www.howtogeek.com/167723/how...8.1-so-that-you-can-install-unsigned-drivers/
2) We download the drivers, which we extract in our desktop.
3) We connect the device while switched off to PC via a USB 2.0 port, and we launch Windows device manager. We press simultaneously Vol +/Vol -/Power button for ~5 seconds. We should see our device identified as QHUSB_BULK under Ports section in device manager. If we get prompted to format several drives we cancel all of the actions.
4) We right-click at device QHUSB_BULK > Update Driver > Browse my computer for driver software > Let me pick from a list of device drivers on my computer > Have disk > Browse, and we open Nuova cartella folder which we have extracted, containing the drivers.
We choose the driver named Qualcomm HS-USB QDloader 9008 and we install it.
We can see our device now identified with that name in the device manager.
5) We download Nubia Toolstudio , and Z7 mini files.
We extract them inside a folder in our desktop, and we run toolstudio as administrators, disabling our anti-virus, or putting the program to its' exceptions because it will be detected as malware.
In the prompt which will pop-up requiring a password, we enter the e-mail address found at the .txt file.
6) We select eMMC Download, we refresh and we should see our device identified like this.
7) We select browse, and we select the folder nx507J_files containing the Z7 mini files.
8) We select start all, and we wait until the procedure finishes.
The whole process has ended, we unplug our device and we can boot it. We will be with stock rom 1.28
Hi Stratos,
i was able bevor to google translate the italian text an d using the screenshots avaliable there i was able to flash the Nubia 7 MAX
software. BUT no imeis are in the Phone so now i have to find a method to type the IMEI numbers in the Phone dont know how..
I tried to create a flashable zip (as suggested by nano7mobile.blogspot) but did not work maybe becuase i dont know
the IMEI Folder location inside the Phone..
Simos
previously after bricked zte z7 max, can flash with ToolStudio : http://www.needrom.com/download/z7-max-2-13-android-5-beta_eng_chi/ (file: NX505J_CNCommon_V2.13.tar)
voila, phone revive.. thankyou..
Another Problem is Appear..
Imei,Meid, is gone.
i backup imei (blank) with Qpst, generate name: blank_imei.QCN ( ^^)
edit my own file : blank_imei..QCN (with blank imei,meid,esn)
the file is about 141 KB.
i open with hexa editor, feel confuse, don't know where to start, don't know the location of imei,meid,esn.
i don't know where "offset" position to be edit.
i google around,
i think need file : *.QCN from someone z7 max backup, to determine the position of imei,meid,esn. (cmiiw)
can someone help me, provide backup of Z7 Max *.QCN file?
i will Surely change it with hexa editor, edit it with my own imei,meid,esn.
or there is another way to fix this imei-meid-esn problem?
please help...
best regard's
stratos_21 said:
I have done this procedure on my device without any problem after a repartition failure, but I am not responsible about anything happens to your device (which is already bricked...)
The source is http://www.androidiani.com/forum/zte-nubia-z7/446548-guida-di-unbrick-z7-max-mini-27.html
1) We disable driver signature verification for windows.
- Windows XP https://mega.co.nz/#!30I1yLRD!kLblCqP9_LmiOXjpfzGbFL7m2zqAqKqZ8ciPFWMBDB0
- Windows 7 http://www.sabrent.com/support/knowledgebase.php?article=14
- Windows 8 http://www.howtogeek.com/167723/how...8.1-so-that-you-can-install-unsigned-drivers/
2) We download the drivers, which we extract in our desktop.
3) We connect the device while switched off to PC via a USB 2.0 port, and we launch Windows device manager. We press simultaneously Vol +/Vol -/Power button for ~5 seconds. We should see our device identified as QHUSB_BULK under Ports section in device manager. If we get prompted to format several drives we cancel all of the actions.
4) We right-click at device QHUSB_BULK > Update Driver > Browse my computer for driver software > Let me pick from a list of device drivers on my computer > Have disk > Browse, and we open Nuova cartella folder which we have extracted, containing the drivers.
We choose the driver named Qualcomm HS-USB QDloader 9008 and we install it.
We can see our device now identified with that name in the device manager.
5) We download Nubia Toolstudio , and Z7 mini files.
We extract them inside a folder in our desktop, and we run toolstudio as administrators, disabling our anti-virus, or putting the program to its' exceptions because it will be detected as malware.
In the prompt which will pop-up requiring a password, we enter the e-mail address found at the .txt file.
6) We select eMMC Download, we refresh and we should see our device identified like this.
7) We select browse, and we select the folder nx507J_files containing the Z7 mini files.
8) We select start all, and we wait until the procedure finishes.
The whole process has ended, we unplug our device and we can boot it. We will be with stock rom 1.28
Click to expand...
Click to collapse
I bricked it yesterday trying to downgrade from cm12.1 to Official nubia 3.01. Yesterday it showed up as QHUSB_BULK, but now it shows up as android cd rom drive and I can't do anything with it. Currently it will boot into the nubia recovery and it will charge, I can't enable it as mass storage device . I can see that all my files are there through the recovery but I can't gain access to them. Will it let me flash from External USB micro sd card as I am about to go buy one? If I turn it on it goes straight into nubia recovery and when I have it off it charges.
When you said 1.28 did you mean Official 1.82? The 1.82 did not work for me as I had an official 1.82 already downloaded. The file you linked I could not download due to poor connection. I was able to install Nubia 3.01 but I think I lost my imei because it says no sim detected. Fortunately, I do have an efs backup from HC-kTool - will I be able to restore that? Also all of this began as I went straight to V3.01 instead of V2.03, first . And then I went to cm12.1 which was extremely buggy so I try to downgrade to official v3.01 and then to Kitkat 4.4.4 v1.82 when something happened to the pc and phone lost connection during the downgrade.
What should I do next? I currently am on Lollipop 3.01 with no radios, baseband etc. My blue-tooth and wi-fi are working. Should I try to restore my efs.img I backed up with HC-kTool?
next4nextel said:
I bricked it yesterday trying to downgrade from cm12.1 to Official nubia 3.01. Yesterday it showed up as QHUSB_BULK, but now it shows up as android cd rom drive and I can't do anything with it. Currently it will boot into the nubia recovery and it will charge, I can't enable it as mass storage device . I can see that all my files are there through the recovery but I can't gain access to them. Will it let me flash from External USB micro sd card as I am about to go buy one? If I turn it on it goes straight into nubia recovery and when I have it oharges.
Click to expand...
Click to collapse
I'm in a similar situation with mine, self inflicted of course while I was trying to get the phone rooted with 3.01.
Anyway where it is now I can still boot to a point and I still have the Nubia recovery util fully functional. If you go into that and look under 'other' you will see that you have the ability to enable mass storage from there and yes you have the option of updating via SD,internal and OTG via the recovery util.
For me though unless I want to get nasty and do things from scratch it looks like I can only carry out an update using an official Nubia file and not just a recovery nor an earlier or current version of stock firmware which is kind of weird. And yes you have the option of updating via the SD,internal and OTG via the recovery util.
Thanks Parso, fortunately I followed the above steps and I restored to official 5.0. but then I lost my imei and had to sort that out. I actually like the official 5.0 except for 2 bugs one where I can't see the WiFi icon on the status bar unless I'm connected to Wi-Fi. And the other is sometimes when I get a call the screen never lights up and I can't swipe to answer the calls which is really annoying because I have to call them back.
I have the same situation right now.I upgraded my z7max 1.64 to 3.09.then I tried cm12 but there were so many problems with mobile data.
So I decided to change it.It was a big mistake to go back to 1.64 without reading anything.In the end it stopped working after a few trys.
Anyway I managed to enter toolstudio 4.6 and show it at por as com13 .Then I watched steps and flashed 3.09 to phone.It seemed like succesfull but it wasnt.Now it s not reacting and all black screen.
Also when I connected it to computer again at the beginning it was QHUSB_BULK with yellow sign.Then I tried to install Qualcomm CDMA Technologies MSM to set it up.Now it became worse.When I connect my phone it s written "unidentifed device" on device manager.
I guess we re missing one thing.For example this "Qualcomm CDMA Technologies MSM" or qhsusb驱动 folders are for XP, Vista or 7. I m using windows 8 right now and I think these files are not suitible as drivers.
So my phone is dead now.If I can set drivers up I guess I can fix it.But I cant find any other drivers and that s the biggest problem.
Hi everyone,
My feedback, After try CM12.1 i decided to return at android 4.4 and for that i used nubia updated tools and nubia studio.
After flash, no imei and only USA Band.
After restored my NV backup 1 IMEI of 2 come back ?!, After restore my
NV Value (values from opo guide, because NV Calculator give me a bad number ?) all band done USA, ENRO, JAPAN etc ...
BUT the phone lock/unlock (after enter my lock pin) every 5 secondes ?
Please help me, i have no ideas
buzz-27 said:
Hi everyone,
My feedback, After try CM12.1 i decided to return at android 4.4 and for that i used nubia updated tools and nubia studio.
After flash, no imei and only USA Band.
After restored my NV backup 1 IMEI of 2 come back ?!, After restore my
NV Value (values from opo guide, because NV Calculator give me a bad number ?) all band done USA, ENRO, JAPAN etc ...
BUT the phone lock/unlock (after enter my lock pin) every 5 secondes ?
Please help me, i have no ideas
Click to expand...
Click to collapse
For all those who are facing issues unbricking the phone as given above, use these Qualcomm drivers (5th post from top)
http://forum.cyanogenmod.org/topic/71825-hard-brick-to-hell-and-back-guide-to-recovery/page__st__40
Point to these drivers from Device manager (QHUSB_BULK). Your device should be identified correctly. Also follow the same steps exactly as given earlier. I managed to unbrick with completely working phone & IMEI.
If anyone is intersted in reading why Qualcomm devices cannot be bricked completely, read the links given below in 2 parts
http://www.androidbrick.com/ultimate-qualcomm-snapdragon-unbrick-guide-snapdragons-are-unbrickable/
http://www.androidbrick.com/unbrick...oader-9008-if-you-have-the-right-kind-of-rom/
next4nextel said:
Thanks Parso, fortunately I followed the above steps and I restored to official 5.0. but then I lost my imei and had to sort that out. I actually like the official 5.0 except for 2 bugs one where I can't see the WiFi icon on the status bar unless I'm connected to Wi-Fi. And the other is sometimes when I get a call the screen never lights up and I can't swipe to answer the calls which is really annoying because I have to call them back.
Click to expand...
Click to collapse
Hello,
COuld you please tell me how you solved the problem, cause all imei and meid are:null
Please someone help me fix the imei problem, i have my imei nr's on the box, but i did not do a back-up.
Thank you
zte z7 mini
hi bad rom update and can not get back into recovey have looked at the posts but drivers link down and when i get Nubia Toolstudio i downloade 3 times put needs password ??? any help please i am runing on windows 10 64bit and win 7 32 bit if some can help on here or mail me on [email protected] going mad with this
Hi, this is my first post here. XDA-forums are great and I think here is the place where you would help me to solve the problem with my phone Nubia z7max.
The problem is that after a software (ROM) update in recovery TWRP from the stock 3.22 to Mokee (android 6 ) , the phone remained on logo "Nubia powered by Android". I have read probably everything written about that problem in all possible places that I found around the internet including Chinese NUBIA forum, Androidiani, 4PdA and so on. I followed all the steps which incidentally are the same everywhere for fixing the phone:
http://forum.xda-developers.com/zte-z7/general/unbrick-nubia-z7-mini-t3006268/page2
stratos_21 said:
I have done this procedure on my device without any problem after a repartition failure,
but I am not responsible about anything happens to your device (which is already
bricked...)
The source is http://www.androidiani.com/forum/zte-nubia-z7/446548-guida-di-unbrick-z7-max-mini-27.html
1) We disable driver signature verification for windows.
2) We download the drivers, which we extract in our desktop.
3) We connect the device while switched off to PC via a USB 2.0 port, and we launch Windows device manager. We press simultaneously Vol +/Vol -/Power button for ~5 seconds. We should see our device identified as QHUSB_BULK under Ports section in device manager. If we get prompted to format several drives we cancel all of the actions.
4) We right-click at device QHUSB_BULK > Update Driver > Browse my computer for driver software > Let me pick from a list of device drivers on my computer > Have disk > Browse, and we open Nuova cartella folder which we have extracted, containing the drivers.
We choose the driver named Qualcomm HS-USB QDloader 9008 and we install it.
We can see our device now identified with that name in the device manager.
5) We download Z7 mini files.
We extract them inside a folder in our desktop, and we run toolstudio as administrators, disabling our anti-virus, or putting the program to its' exceptions because it will be detected as malware.
In the prompt which will pop-up requiring a password, we enter the e-mail address found at the .txt file.
6) We select eMMC Download, we refresh and we should see our device identified like this.
7) We select browse, and we select the folder nx507J_files containing the Z7 mini files.
8) We select start all, and we wait until the procedure finishes.
The whole process has ended, we unplug our device and we can boot it. We will be with stock rom 1.28
Click to expand...
Click to collapse
The difference in my case is that the procedure for flashing have completed with no errors and the phone restarts and it is in the same condition without any change: the logo "NUBIA powered by Android".
I tried to maybe over 10 different drivers. The phone is detected by the computer as it should be. When downloading the ROM in to the phone with ToolStudio_4.6 or NX505J Nubia Tool V2.1.0, procedure runs without any problems but the result is the same. There is no possibility to enter into recovery, I was TWRP and accordingly have a backup made in TWRP ahead of time when my phone is working normally.
With the combination Vol+, Vol- & Power pressed together for about 7-8 seconds the phone is recognized by the computer as HSUSB_Bulk and a cuple of disc drives with a different volume. Drivers are installed correctly although hardware is 19d2 and the phone is recognized as Qualcomm HS-USB QDLoader 9008 (COM XX).
With the combination Vol+ & Power pressed together for about 7-8 seconds the phone is recognized as Android ADB Interface, on screen are Nubia logo. In this kind I can charge (at least visibly) TWRP through "Z7_Max_All_In_One_Tool_Created_By_Tigreos" (NeedRom), but after that I can not go into Recovery. With the same tool I can install stock recovery too but still can not login to recovery.
The biggest success I've achieved after many attempts, two weeks from now, are to initial animation pictures and melody at startup and phone suddenly goes off.
Pleace Help