[Q] GT-I9300 showing up as "unknown device" in Win7 x64 - Galaxy S III Q&A, Help & Troubleshooting

OK just bought my GF a GT-I9300, I'm a bit new to samsung I'll admit, but I'm not new to modding... just not sure what I've done wrong, or haven't done yet that is holding me back...
here is what I've done so far:
1. downloaded mskip's multi-tool
2. downloaded Chainfire's CF-AutoRoot
(I know I know, slightly redundant, but I wanted more than one option to accomplish the goal)
3. Installed Samsung Drivers via mskip's tool
4. Set phone to "media device" (seemed the proper option for win7)
5. disconnected phone
6. pulled battery and replaced
7. held home + vol down + pwr
8. connected usb to pc
here is where the issue is, now at this point I get a message in windows that driver installation has failed (I thought they were already installed???) and phone shows up as "unknown device" and I cannot see it in Odin or ADB...
I tried this which I found somewhere:
Code:
try to key in this in dialer
*#7284#
it has 4 option there..
UART
MODEM
PDA
USB
MODEM
PDA
For usb. select the PDA.if it already selected to PDA. reselect it by select MODEM and then PDA again.. Only change the USB setting.. and then press back. try reconnect to kies again..
hope it helps..
but I get an invalid code message after hitting the send/talk button... so without the ability to flash insecure boot img, I cannot attain root... would really appreciate some help, I may not be using proper search terms but I have not come up with much on XDA and as far as google, all I could really find, was the above advice which seems to pertain to the S2, not the S3...
will happily donate to anyone that can help!

Only thing I can think of is you have a rom which doesnt support that dialer code, or your not using samsungs dialer. Works ok here.
I can see:
Uart = modem
Usb = pda
As for unknown driver I dont think I ever installed any driver on win7 x64. Bit hazey but I think I just plugged the usb cable in. Try uninstalling the drivers or kies and retry.
Where did you set media device? Dont remember doing that either.
Sent from my GT-I9300 using xda premium

ficti0n851 said:
Only thing I can think of is you have a rom which doesnt support that dialer code, or your not using samsungs dialer. Works ok here.
I can see:
Uart = modem
Usb = pda
As for unknown driver I dont think I ever installed any driver on win7 x64. Bit hazey but I think I just plugged the usb cable in. Try uninstalling the drivers or kies and retry.
Where did you set media device? Dont remember doing that either.
Click to expand...
Click to collapse
thanks for your reply, I will attempt uninstalling the drivers and see if that makes a difference, I'll let you know after the GF gets back from shopping... appreciate the reply though!
as for setting as media device, when I plugged it in, there is a notification that says phone connected as "usb XXX" if you tap that, you have three options first option is USB Storage, second is Media Device, and third is an option for systems that don't support MTP...

Hmmm never seen mass storage mode on my phone when I connect via usb. Could be a driver problem.
Sent from my GT-I9300 using xda premium

Related

[Q] Stuck In Download Mode

after a couple failed odin flashes
my PHONE is STUCK in DOWNLOAD MODE and i can't use ODIN because my PC now says USB NOT RECOGNIZED
ive uninstalled/reinstalled driver
different ports..different usb cables..different pc and still no luck..and yes ive searched xda..and i have yet to find anyone with similar issues..any ideas?
i finally got my phone to work
IT SEEMS LIKE WINDOWS DOESNT BOTHER TO TRY TO INSTALL THE DRIVERS SO YOU HAVE TO DO IT MANUALLY THROUGH DEVICE MANAGER
1) download http://www.multiupload.com/NMPX3KMWRS
this has the 64 & 32 bit driver folders..put which ever one u use on ur desktop
2) open device manager..plug your phone..if your pc says usb not recognized and unknown device shows in device manager..right click..properties..then uninstall it..
3) unplug ur phone..plug it back in then unknow device should show up in device manager..go to its properties then click update driver..the select own drivers..then browse to the 64 or 32 bit folder and click ok then next..it will try to install but you might get a error..
hopefully it will say install gadget serial and fail..that means ur pc kinda recognizes it
then all u ahve to do is from there is go to device manager..go to the properties of gadget serial..update driver..and browse to the driver folder..and it should install..then u have to do it a couple of more times for when it recognizes other samsung devices such as the adb and composite
Instructions here
http://forum.xda-developers.com/showthread.php?t=803492
First, download http://www.multiupload.com/NMPX3KMWRS
This contains Odin, the Samsung Drivers, stock odin rom, updated odin rom, pit file.
If you don't want to lose your settings, etc. you can skip to the second part. If your phone still doesn't work than start from the top.
-PART 1-
Step 1.) Make sure you have the appropriate drivers installed for your phone. If you are on 64bit then choose 64, if you are on 32 choose 32. You may already have the drivers installed and it will tell you after you try to install them.
Step 2.) Power your phone off
Step 3.) Open Odin.exe and plug a usb cable to your computer that will connect to your phone (do not plug it in to the phone yet, just the computer)
Step 4.) Hold down both volume buttons at the same time and while holding them down plug the usb into your phone. You should see a COM message show up in Odin.
Step 5.) To ensure your phone is back to stock, in odin you will want to check the repartition button. ONLY CHECK IT WHEN YOU ARE FLASHING BACK TO STOCK. Leave the other check boxes the way they are.
Step 6.) Click the PIT button and select the 512.pit file
Step 7.) Click the PDA button and select Original.tar and then click Start
It should go through a bunch of steps and then your phone will reboot. Below are the steps to update it to the latest release.
Close Odin and power your phone off.
-PART 2-
Step 1.) Open Odin.exe and plug a usb cable to your computer that will connect to your phone (do not plug it in to the phone yet, just the computer)
Step 2.) Hold down both volume buttons at the same time and while holding them down plug the usb into your phone. You should see a COM message show up in Odin.
Step 3.) Leave all check boxes the way they are. Do NOT check the repartition box.
Step 4.) Click the PIT button and select the 512.pit file
Step 5.) Click the PDA button and select T959UVJI6.tar and then click Start
Hope this helps!!!
thanks for the idea..but i know how to do all that...
MY PROBLEM
my PC doesnt recognize my phone and its in download mode so i cant use odin
He gave u the link to the drivers your computer doesn't recognize your phone because the drivers uninstalled themselfs it happed to me also just do it see if it helps k
SmartBrother90 said:
thanks for the idea..but i know how to do all that...
MY PROBLEM
my PC doesnt recognize my phone and its in download mode so i cant use odin
Click to expand...
Click to collapse
Sent from my SGH-T959 using XDA App
Thegreat520 said:
He gave u the link to the drivers your computer doesn't recognize your phone because the drivers uninstalled themselfs it happed to me also just do it see if it helps k
Sent from my SGH-T959 using XDA App
Click to expand...
Click to collapse
if you look in my first post i said
"ive uninstalled/reinstalled drivers"
and if i said i tried it on other pcs that would me i would have to install drivers there too..so the driver idea has already been tried..thanks anyway
Hey, I know u said Odin wont recognize your phone, but does your computer recognize that the device or an unknown device has been attached when u plug your phone into the USB. What version of windows are you using.
Jonathan Rubcic
Electrical Engineer
Sent from my SGH-T959 using XDA App
Sorry, u said your computer recognizes that an unknown device is plugged in. Let me see what I can find. If you can get Into download mode, your phone can be fixed!
Jonathan Rubcic
Electrical Engineer
Sent from my SGH-T959 using XDA App
jarubcic said:
Sorry, u said your computer recognizes that an unknown device is plugged in. Let me see what I can find. If you can get Into download mode, your phone can be fixed!
Jonathan Rubcic
Electrical Engineer
Sent from my SGH-T959 using XDA App
Click to expand...
Click to collapse
my phone is in the download mode..matter of fact..its the only mode i can get into..but i cant do anything because my pc wont recognize it
I know this seems simple.... But unplug phone, shut down ODIN, re-open ODIN, plug phone back in.
SmartBrother90 said:
after a couple failed odin flashes
my PHONE is STUCK in DOWNLOAD MODE and i can't use ODIN because my PC now says USB NOT RECOGNIZED
ive uninstalled/reinstalled driver
different ports..different usb cables..different pc and still no luck..and yes ive searched xda..and i have yet to find anyone with similar issues..any ideas?
Click to expand...
Click to collapse
same problem here
All~G1 said:
I know this seems simple.... But unplug phone, shut down ODIN, re-open ODIN, plug phone back in.
Click to expand...
Click to collapse
tried that and still nothing
All~G1 said:
I know this seems simple.... But unplug phone, shut down ODIN, re-open ODIN, plug phone back in.
Click to expand...
Click to collapse
yea that doesnt work & it wouldn't. because the pc has to recognize the phone before odin can..an that the issue! thanks tho
I've also got this probem. Did you by any chance install the voodoo thing? Apparently it messes up your phone if you flash over it.
I think I might buy one with a broken screen for 200ish...............but I really hope I dont have to.
Anyone have a fix for this yet?
@xaymaca i finally got mines to work after 48 hours but it seems like it depends on luck
1) download http://www.multiupload.com/NMPX3KMWRS
this has the 64 & 32 bit driver folders..put which ever one u use on ur desktop
2) open device manager..plug your phone..if your pc says usb not recognized and unknown device shows in device manager..right click..properties..then uninstall it..
3) unplug ur phone..plug it back in then unknow device should show up in device manager..go to its properties then click update driver..the select own drivers..then browse to the 64 or 32 bit folder and click ok then next..it will try to install but you might get a error..
hopefully it will say install gadget serial and fail..that means ur pc kinda recognizes it
then all u ahve to do is from there is go to device manager..go to the properties of gadget serial..update driver..and browse to the driver folder..and it should install..then u have to do it a couple of more times for when it recognizes other samsung parts.
it seems like windows doesnt want to install the drivers itself
um, you just tried alot with those drivers and it eventually worked out differently?
RPGbig said:
um, you just tried alot with those drivers and it eventually worked out differently?
Click to expand...
Click to collapse
no basically first i uninstalled the "unknown device" through device manager
then i would plug the phone..go to device manager and update the drive manually..until gadget serial showed up..if not..i repeat the process..
then when gadget serial shows up..update its driver manually..then samsung adb should show up in device manager..it takes alot of time and patience
If your system still fails to recognize your phone. Try installing Mini Kies. Do a quick search there are plenty of download links for that software. Make sure you restart your system after uninstalling the device.
I had similar issues with myn. But eventually got over with by doing a clean install off the drivers.. Hope this helps.
so i did that and it recognized my phone. it says it on the computer and on odin it changed from 0:[COM4] to 1:[COM3]. but it still stays stuck on set PIT file DO NOT TURN OFF TARGET.
Jessejess87 said:
so i did that and it recognized my phone. it says it on the computer and on odin it changed from 0:[COM4] to 1:[COM3]. but it still stays stuck on set PIT file DO NOT TURN OFF TARGET.
Click to expand...
Click to collapse
what tar and pit files are you using, i had similar issues when i tried odin'ing back to ji6. however odin'ing to stock JFD worked beautifully. if you need help finding the proper odin files here is a mirror of them: Odin Mirrors
This happened to me before, and someone mentioned it earlier. Get into device manager on windows, go to the Universal Serial Bus (USB) section, and I uninstalled every option you see in there. Restart your computer and windows will automatically reinstall those items apon reboot. The phone should now be detectable...
EDIT: Fail, it appears you already got it solved...
hey im not sure what tar abd pit files are. im really new to this. question, with the mirror how would i use it? will it still work with my phone trippin lol and not being picked up on my computer.

Rooting guide of Intratech DOES work! :)

Hi all! The rooting guide of Intratech given here : http://forum.xda-developers.com/showthread.php?t=1075278 DOES NOT WORK! I have an SGS II Kernel version of KE8 (India) and I tried to follow the steps given in the guide, but when I open ODIN and connect my phone in Download mode with my laptop via USB Cable, ODIN is not connecting to the phone. The box meant to turn yellow does NOT change color. Nothing happens at all. Why is this so? I cannot post in the relevant thread because I am a newbie in the forun
Have you installed kies first to get the drivers?
Sent from my GT-I9100 using XDA Premium App
Yes, of course, I have the latest version of Kies installed on my laptop and I use it regularly to connect with my SGS II. I kept Kies closed when trying the rooting procedure as mentioned in Intratech's guide. Started phone in download mode. Opened Odin on laptop, then connected phone via USB........the box which is supposed to turn yellow on connection, doesn't light up. Nothing happens at all.
TheMegastar said:
Hi all! The rooting guide of Intratech given here : http://forum.xda-developers.com/showthread.php?t=1075278 DOES NOT WORK! I have an SGS II Kernel version of KE8 (India) and I tried to follow the steps given in the guide, but when I open ODIN and connect my phone in Download mode with my laptop via USB Cable, ODIN is not connecting to the phone. The box meant to turn yellow does NOT change color. Nothing happens at all. Why is this so? I cannot post in the relevant thread because I am a newbie in the forun
Click to expand...
Click to collapse
I suggest to you that the overwhelming majority of the people who use the guide will disagree with you and provide evidence to the fact that it does, indeed, work. The fact that it does not work for you suggest that you are doing something wrong or have a problem with your computer.
I would suggest that you ensure that KIES is also closed in the system tray of your computer before opening Odin and connecting the phone. Also ensure that your computer has an internet connection and is able to connect to windows update to download and install drivers. If that doesn't work then change USB port or computer.
By all means, if you find a way that works then feel free to write your own guide. More information is good and maybe others might find your method, if you discover one, easier to follow.
@Intratech: Hi. Thanks for your reply. Ok, so it is not working for me. Can you help?
My laptop is working on Windows 7 Home Premium which is upto date in all respects. My USB port is working fine as I am able to connect my SGS II to Kies through that. Kies was closed when I tried to connect to Odin. Odin version is 1.85. While the phone (in download mode) is connected to the laptop, and Odin is Open, nothing happens. Nothing.
TheMegastar said:
@Intratech: Hi. Thanks for your reply. Ok, so it is not working for me. Can you help?
My laptop is working on Windows 7 Home Premium which is upto date in all respects. My USB port is working fine as I am able to connect my SGS II to Kies through that. Kies was closed when I tried to connect to Odin. Odin version is 1.85. While the phone (in download mode) is connected to the laptop, and Odin is Open, nothing happens. Nothing.
Click to expand...
Click to collapse
Is kies closed in the system tray as well?
Yes, Kies is closed in system tray also. Fully closed. Odin opens, and I see the Odin screen as per your screen shots, but the box which is supposed to light up yellow, does not.
Are you using the Samsung USB cable or a HTC one?
Samsung USB cable which came with the phone box pack. I can see the Auto Reboot and F. Reset Time boxes checked. Nothing else is checked, not even the PDA button. The box saying ID:COM (which is supposed to light up) is blank.
u need to check pda and load the file u want to flash it
then click on start
Look in your program and features list, found in control panel, and see if you have a listing for Samsung USB driver for mobile phones there. If you do then uninstall it and uninstall KIES. Download a new copy of KIES from Samsung and install it. After installing it, make sure you don't have USB debug ticked, connect the phone and leave it until all the drivers install. After that remove the device and lose KIES. Put the tick in USB debugging and connect the phone and leave it so that any needed drivers install. After this put the phone in download mode and connect it, without opening KIES or ODIN, and leave it to download any drivers needed. If it downloads and install any drivers wait for it to finish, once it does then you can go ahead and use Odin normally.
If this doesn't work your PC is at fault, fix it.
cyberwarfare said:
u need to check pda and load the file u want to flash it
then click on start
Click to expand...
Click to collapse
How you going to flash without connecting to the device?
Turn USB debugging off on phone .USB connection should be to a motherboard port .
Reboot phone set phone to connect in USB mass storage mode .
Connect cable wait for Windows to load drivers . You should be able to browse phone via Windows explorer if USB drivers are correct .If so remove cable and reboot phone to download mode . Open Odin select files to load connect cable .
That fails then
Rooting guide of intratech does not work! for you your PC or your phone but for everyone else so give up .
jje
@cyberwarfare: Yes, I tried that. The file loaded, I pressed start. Yet nothing happened. I just saw one line notification in the left hand side column of Odin, which read something like "successes: 0/failures: 0". I am speaking from memory here. Nothing really happened even after loading PDA and pressing the Start button.
@Intratech: Yes, both Kies and Samsung USB Driver for Mobile Phones are there in my program list. I downloaded Kies from their India support site : http://www.samsung.com/in/support/d...1&prd_mdl_cd=GT-I9100LKAINU&srchword=GT-I9100
Worth mentioning here that the USB debug check box was ticked when I tried to Root with Odin.
So basically, you're asking me to uninstall & reinstall Kies and its drivers. Ok, will do. It will take time so will do it when I have a little more time on my hands. Thanks for your help & your time. I appreciate. If you have time, then look at my other post here which says, "7 major issues with SGS II" ...... and help with solving my other issues like that of bluetooth not connecting and phone ringer's erratic behaviour. Thanks a ton.
Mate I haven't used the Indian firmware so I'm not too sure about troubleshooting it. There is an Indian thread in the general forum where you may be able to get more help with the issues you have.
@JJEgan: Thanks for replying. All my USB Ports are on the motherboard itself, worth mentioning that the same USB port works fine when I connect the phone to the laptop. Am able to transfer files to and fro via the same USB port.
"set phone to connect in USB mass storage mode".....how do I do that? Where to find that in phone settings?
I am able to browse the contents/files on the phone very well...so this proves my drivers are fine. So which basically means, that Intratech's rooting guide does not work FOR ME! Happy? This may be a problem specific to the India specific phones....Kernel version is 2.6.35.7-I9100XWKE8-CL214845
[email protected] #2
PDA : I9100XWKE8
Phone : I9100DDKE2
CSC : I9100ODDKE2
Build Info : Wed May 18 13:55:45 KST 2011
@Intratech: Thanks mate. I've posted my problem in the India specific thread also.....lets see if someone replies. But the problem is not with the rooting procedure, the problem is that I can't even seem to get started with the procedure as there is no connection between Odin and the phone.
Nah, it's not with the firmware. The other Indians who use it have no issue following the guide.
Please try and reinstall everything as I've stated and see if that work. Also, when you go into download mode what do you see on the screen?
In download mode I see a static warning on the screen which tells me of the risk and tells me I have to press the VOL down button to cancel this, and there is a yellow triangle at the bottom. The screen stays there as I connect the USB cable to the laptop.
TheMegastar said:
In download mode I see a static warning on the screen which tells me of the risk and tells me I have to press the VOL down button to cancel this, and there is a yellow triangle at the bottom. The screen stays there as I connect the USB cable to the laptop.
Click to expand...
Click to collapse
You need to read the instructions start off by reading what it says on that screen .Do not read half of the instructions like you are its very dangerous flashing if you cannot read and follow the instructions and i advice you dont flash .
The screen message you are not reading is the sentence above the one you posted .
To install custom rom press Vol Up key .
jje
TheMegastar said:
In download mode I see a static warning on the screen which tells me of the risk and tells me I have to press the VOL down button to cancel this, and there is a yellow triangle at the bottom. The screen stays there as I connect the USB cable to the laptop.
Click to expand...
Click to collapse
Right this is your problem, you have not put the phone in download mode as yet. Press volume up at this screen to enter download mode and now you will connect.

[Q] I rooted my GN and now my computer doen't recognize it, any fix?

Hi Folks, I rooted my GN a few days ago with no problem. Now that I want to flash a Recovery to Install a ROM the computer don't recognize the phone. I have tried a few methods that I saw online with no results.
Looking for some help! Thanks in advance!
On a Windows machine go to Start/Control Panel/Windows Update. With the phone plugged directly to the PC, not a hub and click "check for updates". You might have to do this a few times and reboot, I did.
Odds are you tried this, but just in case....
USB Driver Not Being Recognized For SYNC
Following are my observations and possible steps to
5. solution lies in the phone
a. key in the dialer *#7284#
b. it has 4 option there..
UART (MODEM/PDA)
USB (MODEM/PDA)
c. For USB. select the PDA. If it already selected to PDA, reselect it by select MODEM and then PDA again.. Only change the USB setting.. and then press back. try reconnect.
6. The Laptop will start recognizing the required drivers and install them
also Phone is not recognized by laptop when it is in USB debug mode, MyPhoneExplorer does not recognize when it is not in Debug mode
aj_vogtman said:
On a Windows machine go to Start/Control Panel/Windows Update. With the phone plugged directly to the PC, not a hub and click "check for updates". You might have to do this a few times and reboot, I did.
Click to expand...
Click to collapse
aj, Im installing some updates now and I will tell u then the results!
Sent from my SAMSUNG-SGH-I717 using xda premium
enjoythemusic said:
Odds are you tried this, but just in case....
USB Driver Not Being Recognized For SYNC
Following are my observations and possible steps to
5. solution lies in the phone
a. key in the dialer *#7284#
b. it has 4 option there..
UART (MODEM/PDA)
USB (MODEM/PDA)
c. For USB. select the PDA. If it already selected to PDA, reselect it by select MODEM and then PDA again.. Only change the USB setting.. and then press back. try reconnect.
6. The Laptop will start recognizing the required drivers and install them
also Phone is not recognized by laptop when it is in USB debug mode, MyPhoneExplorer does not recognize when it is not in Debug mode
Click to expand...
Click to collapse
enjoythemusic, also I had tried this before and doesnt work for me. Thanks for your help. Im installing some updates now and will see if work if not will do this again over the updates!
Sent from my SAMSUNG-SGH-I717 using xda premium
I rooted the stock GB yesterday then flashed DAGr8's ICS rom with a ton of mods afterwards and mine is functioning fine.
I did notice a Samsung driver available as an optional install in Windows Updates. Is that the one you tried to install?

Odin does not see phone

Help mee.
I have bought a s3 that is locked to Orange, need to unlock, but odin does not see the phone in recovery/dl mode.
Odin see the phone in normal mode , but each time i put into start/+vol/home odin see nothing.
I have kies updated.
Thanks
crazydiamond1970 said:
Help mee.
I have bought a s3 that is locked to Orange, need to unlock, but odin does not see the phone in recovery/dl mode.
Odin see the phone in normal mode , but each time i put into start/+vol/home odin see nothing.
I have kies updated.
Thanks
Click to expand...
Click to collapse
I had a similar thing when i was plugged into a usb hub
Was ok when i plugged directly into the pc
Install Samsung Kies to be able your PC to detect your phone via Odin
also check the debugging mode in the developer options
bordikun said:
Install Samsung Kies to be able your PC to detect your phone via Odin
also check the debugging mode in the developer options
Click to expand...
Click to collapse
I have Kies, also tried debugging, i need root to unlock phone
Try to use the latest Odin
Odin v3.04
bordikun said:
Try to use the latest Odin
Odin v3.04
Click to expand...
Click to collapse
I have uninstalled the older Kies, re installed the latest.
I have installed the lastest odin.
Have tried to link up with and without debugging, odin still does not see phone when in recovery mode.
Only time odin see the phone when phone is in normal mode.
Starting to get annoyed now lol, i cant cut my sim to fit phone, untill this is done
I cant see my s2 on odin either, what am i doing wrong ????
1. Reboot PC
2. Ensure KIES is not running and kill any KIES processes in PC task manager.
3. Download mode
4. Connect USB directly to PC port (no hub)
5. Wait for any drivers to instal or load on PC
6. Start Odin in administrator mode
If still no good;
a) Different USB cable
b) Different PC USB port and wait for drivers
Sent from my GT-I9300 using xda premium
Thanks . Seems that I had been pressing volume up not down.
I have another question . I used chainfire Rom to debrand the phone but keis does not recognize . How can I solve this . Could it be because the phone is rooted ?
i am having this problem at the mo, I have tried all of the above, apart from a different pc.
oden worked fine with my galaxy s2
is there any more updates on how to sort this out please?
thanks
ian
I know this is a 7 day old thread, but I feel for you having been in the same situation. Firstly, have you installed the Android SDK? If not then I advise you to do so. Do a search on how to install the SDK. There maybe smaller downloads available with a package of the binaries you need to do some testing i.e. adb. The instructions will elaborate about how to set up your Environment settings in Windows. Essentially ADB needs to be called from within any part of your Windows system....or else you will have to cd to its location each and every time you want to do something like this. So once you have done that, open command prompt and type adb and see what comes up? If it says bad command or file name it means your environment settings for the ASK are incorrect, if it displays the adb help text in command prompt you are ready to proceed.
When you plug your device in (not in DL or recovery modes) is it detected by the PC? If so then your drivers are probably fine. If not then it maybe 1 of 2 things? 1 the device is detected but the MTP drivers have not been loaded or 2. No detection what so ever and all drivers need to be installed.
To determine how to proceed you will need to do a bit of investigating.
Note the USB drivers are included as part of the Android SDK.
Check in Device manager inside of Windows to see if anything is detected when you plug it in. If so but it has a yellow exclamation ! then it would indicate you need to update your drivers (but not always?). From here you can test to see if the phone is detected and you only need MTP drivers.
If not then I would suggest uninstalling Keis all together and downloading and installing the Samsung USB drivers separately. Install the drivers. Plug in the phone. If it is not detected straight away, then reboot the PC then plug the phone into a different USB port. From here you can determine how to proceed by using adb.
plug your phone in via USB and open command prompt and type this: adb devices
You should see 1 of 2 things.
1) The words "list of devices attached" followed by a 16 digit long ID number a gap and the word "device"
2) just the words "list of devices attached" and then blank and nothing else?
If a device ID is returned then you can proceed with the following. Otherwise you need to do some additional trouble shooting
Proceed here:
Once it is detected by Windows and shows up in Explorer then unplug the phone and go into settings and developer options and check enable USB debugging. Once you have done this it should allow your device to be seen in DL and recovery modes.
Troubleshoot: If not detected try the following:
1) Reboot the PC and plug into a new USB port that you have not previously plugged into.
2) Try disabling USB debugging plugging the device in and then unplugging it and reenabling USB debugging
3) From the status bar try switching modes between MTP and PTP modes. Wait a good minute or so between to allow Windows to detect the driver change. Tip a good indication is your notification tray Icon with green USB disk with a magnifying glass swirling around....Note if you cannot see this at all you probably should drag it into the notification panel so that you CAN!
4) Open up device manager again and ensure no yellow exclamation marks !
Once all this is right and you can get List of devices attached followed by an ID number then you can for sure be able to detect your device from Odin. Make sure you are running Odin 3.04, run it as admin (not necessary but have heard that it helps?)
Good luck
James
I have an S4 Active that NO MATTER WHAT I DO, Odin will NOT see phone in Download mode, it will with the phone on, and my PC will see the phone, but not Odin. I am stumped. I have tried 3 PC's, I have ALL the drivers and then some. I am Stumped.
rekamyenom said:
I have an S4 Active that NO MATTER WHAT I DO, Odin will NOT see phone in Download mode, it will with the phone on, and my PC will see the phone, but not Odin. I am stumped. I have tried 3 PC's, I have ALL the drivers and then some. I am Stumped.
Click to expand...
Click to collapse
have you tried factory resetting the phone?
afasayan said:
have you tried factory resetting the phone?
Click to expand...
Click to collapse
Several times
rekamyenom said:
Several times
Click to expand...
Click to collapse
You can try with minimal/no drivers i.e. uninstall kies if you have it and delete the drivers you might have installed on your own-it sounds counter productive but it has worked for me a few times.
You can also try to either install kies or the drivers separately.
Try the forum for your own phone, the people there might know better about this problem.
Also what OS are you on?
afasayan said:
You can try with minimal/no drivers i.e. uninstall kies if you have it and delete the drivers you might have installed on your own-it sounds counter productive but it has worked for me a few times.
You can also try to either install kies or the drivers separately.
Try the forum for your own phone, the people there might know better about this problem.
Also what OS are you on?
Click to expand...
Click to collapse
I will give all that a try. I'm on 4.4.2 build NH3. That's why I need Odin, to get back to build NE3
rekamyenom said:
I will give all that a try. I'm on 4.4.2 build NH3. That's why I need Odin, to get back to build NE3
Click to expand...
Click to collapse
By OS I meant the computer's OS.
afasayan said:
By OS I meant the computer's OS.
Click to expand...
Click to collapse
I have tried several computers using Windows 7 and Windows XP both 32 and 64

Galaxy s3 i9300 only charging via usb but not mounting

Bro's I have a galaxy s3 32gb gt i9300 with stock 4.1.2. When I connect the phone to my laptop via usb (laptop is also Samsung) I hear a beep sound on the cellphone and it begins to charge. However, I see no options and no usb connected 3 pin symbol in the panel of phone and nor is there any other option like mount cellphone etc. I do have latest version of Kies installed on my laptop but even that shows no device connected. Please help guys I have spent a bunch of hrs trying to figure out how to get it going but eventually had to register on this forum for help :silly:
Tried a different cable? Usb uses fewer pins to charge than to connect to a pc. Perhaps the cable is damaged (or usb socket).
Sent from my GT-I9300 using Tapatalk 2
Much thanks for the quick reply.... No I don't think the port or the usb is damaged. Further, I'm using the stock usb cable provided with the phone. Any other suggestions?
Ionous said:
Much thanks for the quick reply.... No I don't think the port or the usb is damaged. Further, I'm using the stock usb cable provided with the phone. Any other suggestions?
Click to expand...
Click to collapse
And yes tried different usb cable, plugged it to different pc's, manually downloaded drivers from Samsung but still the dawn thing doesn't work
Edit: just now tried connecting a different cellphone using s3's usb cable on the same usb port and that works fine. So I guess that confirms both the cable and the port are fine
By port, I meant the one on your s3...
Check its clear. If it is, factory reset. If its still a problem, send for repair
Sent from my GT-I9300 using Tapatalk 2
rootSU said:
By port, I meant the one on your s3...
Check its clear. If it is, factory reset. If its still a problem, send for repair
Sent from my GT-I9300 using Tapatalk 2
Click to expand...
Click to collapse
I'm sorry for my quick scan on the thread if I miss something.
Maybe you should try go into recovery and mount USB in there to see what happens or try download mode as well (in this case, with download mode you can see whether USB works or not, if it works then means maybe problem with ROM, so you don't have to send to repair because software issue is not really a issue here, and if it doesn't, then download flash won't start so won't affect on your warranty for flash counts )
Sent from my GT-I9300 using xda premium
I had this problem before with a new brand cable, i just solved the problem buyin a usn charger for Cielo cards.
amazing.
Solved
I tried everything possible....
uninstall drivers. reboot laptop. install drivers. reboot laptop. plug in phone. no sucess.
put phone in download mode and plugged in. no success.
tried on different laptop running Windows 8 and Windows XP. Still no success.
Then i read about this somewhere...
said uninstall drivers. reboot laptop. install drivers. reboot. make sure USB debugging is OFF. Plug in phone. Switch ON USB debugging. Laptop should now detect the phone. But that didnt happen either. No success again.
Also read....
Go to phone dialer.... dial *#7284# to access PhoneUtil > "Qualcomm USB Settings" > set it to "MTP + ADB" .... phone will reboot. Then connect via USB and everything will be ok.
Unfortunately....
dialing *#7284# to access PhoneUtil did not show me Qualcomm USB setting.
It gave me 2 options:
UART> Modem or PDA (here Modem was selected for me by default)
and
USB> Modem or PDA (here Modem was selected for me by default)
I left UART as Modem itself.... but changed USB to PDA. Then click "SAVE and RESET" button.
My phone then rebooted. Once my phone rebooted and i was on lock screen/home screen.... i connected the USB to my phone and voila... my laptop detected my phone as GT-i9300 and show both my SDcard and extCard :good:
Give it a shot and lemme know....
I have same problem. I tried 3 diferent usb cables, two original, 3 computers and nothing. I used MTP few days ago and now nothing in options, just cahrge. I tried factory reset, clean cache, usb debuging on/of, in download mode too... Reinstaled Kies and drivers. I cleaned usb but still nothing. I tried secret code but not have option ADB+MTP. Any help? Sory for my english
webmar said:
I have same problem. I tried 3 diferent usb cables, two original, 3 computers and nothing. I used MTP few days ago and now nothing in options, just cahrge. I tried factory reset, clean cache, usb debuging on/of, in download mode too... Reinstaled Kies and drivers. I cleaned usb but still nothing. I tried secret code but not have option ADB+MTP. Any help? Sory for my english
Click to expand...
Click to collapse
Does #*7284# give you the following:
------—-—-------------
UART
-Modem <--- selected by default
-PDA
USB
-modem
-PDA <--- selected by default
???
If under USB, modem is selected by default, then change and select PDA.
Leave UART value to remain as modem itself. No charge here
Or worse comes to worse...
While keeping phone connected to laptop, enable USB debugging and see what happens.
keneth_c said:
Does #*7284# give you the following:
------—-—-------------
UART
-Modem <--- selected by default
-PDA
USB
-modem
-PDA <--- selected by default
???
If under USB, modem is selected by default, then change and select PDA.
Leave UART value to remain as modem itself. No charge here
Or worse comes to worse...
While keeping phone connected to laptop, enable USB debugging and see what happens.
Click to expand...
Click to collapse
Yes, I tried with that settings and not work, also try to change and same. USB debugging on nothing...
webmar said:
Yes, I tried with that settings and not work, also try to change and same. USB debugging on nothing...
Click to expand...
Click to collapse
OK...
So at the moment your PhoneUtil settings are UART>Modem and USB>PDA right? Leave it at this setting.
Now with the phone connected to you computer... Go to device manager and Uninstall any Samsung drivers that u would see in Device Manager (Windows). If you see anything like adb drivers then also Uninstall. If you have any other phone drivers (Nexus, LG etc), Uninstall those as well. Also from Control Panel>Uninstall a Program, Uninstall any USB drivers programs that u would see in the list.
Once u are certain you have Uninstalled all phone & adb USB drivers. Also Uninstall Kies completely. You might also need to disable Windows auto driver installer. Reboot ur laptop / computer.
Once computer reboots... Google for Samsung USB drivers for mobile phone. The version I used was v1.5.27. You can try with any version. Some people have had the best luck with v1.4.60. Install the drivers and reboot the system again.
Switch off ur phone. And go to download mode.
Then connect ur phone to the computer via USB cable and see what happens? Look in Device Manager again and see what is showing. Also try using a USB 2.0 port for best results.
Once done... Unplug the phone... Get out of download mode.... (u can simply put the battery out of the phone)... Or long press the power button... Let the phone restart. Plug the phone again to the computer and see what happens?
--
Sent from my Samsung S3 (GT-i9300) using Tapatalk
---------- Post added at 07:58 AM ---------- Previous post was at 07:55 AM ----------
keneth_c said:
OK...
So at the moment your PhoneUtil settings are UART>Modem and USB>PDA right? Leave it at this setting.
Now with the phone connected to you computer... Go to device manager and Uninstall any Samsung drivers that u would see in Device Manager (Windows). If you see anything like adb drivers then also Uninstall. If you have any other phone drivers (Nexus, LG etc), Uninstall those as well. Also from Control Panel>Uninstall a Program, Uninstall any USB drivers programs that u would see in the list.
Once u are certain you have Uninstalled all phone & adb USB drivers. Also Uninstall Kies completely. You might also need to disable Windows auto driver installer. Reboot ur laptop / computer.
Once computer reboots... Google for Samsung USB drivers for mobile phone. The version I used was v1.5.27. You can try with any version. Some people have had the best luck with v1.4.60. Install the drivers and reboot the system again.
Switch off ur phone. And go to download mode.
Then connect ur phone to the computer via USB cable and see what happens? Look in Device Manager again and see what is showing. Also try using a USB 2.0 port for best results.
Once done... Unplug the phone... Get out of download mode.... (u can simply put the battery out of the phone)... Or long press the power button... Let the phone restart. Plug the phone again to the computer and see what happens?
--
Sent from my Samsung S3 (GT-i9300) using Tapatalk
Click to expand...
Click to collapse
Oh and make sure USB debugging is Off when doing the above. USB debugging should always be Off... At least till ur pc detects ur phone.
Have the drivers installed on ur system before u are troubleshooting.
--
Sent from my Samsung S3 (GT-i9300) using Tapatalk
I'm facing same problem..
I have Korean version of S3 SHV-E210S..
Android version 4.1.2
Baseband version I9300ZCLK2
I've installed samsung usb driver, kies, and even adb driver installer..
But it doesn't help me at all..
Then i go to his thread, i tried to dial *#7284#, but nothing happen..
I've put it in download mode too..
And my pc can't detect my phone..
Please help me..
Sorry for my bad english..
Please read post # 12.
These are the only things I can suggest.
If all fails then your only option would be to download "Airdroid" from Play store.
It will not solve your issue but will let you transfer files to your phone at least
--
Sent from my Samsung S3 (GT-i9300) using Tapatalk
keneth_c said:
OK...
So at the moment your PhoneUtil settings are UART>Modem and USB>PDA right? Leave it at this setting.
Now with the phone connected to you computer... Go to device manager and Uninstall any Samsung drivers that u would see in Device Manager (Windows). If you see anything like adb drivers then also Uninstall. If you have any other phone drivers (Nexus, LG etc), Uninstall those as well. Also from Control Panel>Uninstall a Program, Uninstall any USB drivers programs that u would see in the list.
Once u are certain you have Uninstalled all phone & adb USB drivers. Also Uninstall Kies completely. You might also need to disable Windows auto driver installer. Reboot ur laptop / computer.
Once computer reboots... Google for Samsung USB drivers for mobile phone. The version I used was v1.5.27. You can try with any version. Some people have had the best luck with v1.4.60. Install the drivers and reboot the system again.
Switch off ur phone. And go to download mode.
Then connect ur phone to the computer via USB cable and see what happens? Look in Device Manager again and see what is showing. Also try using a USB 2.0 port for best results.
Once done... Unplug the phone... Get out of download mode.... (u can simply put the battery out of the phone)... Or long press the power button... Let the phone restart. Plug the phone again to the computer and see what happens?
--
Sent from my Samsung S3 (GT-i9300) using Tapatalk
---------- Post added at 07:58 AM ---------- Previous post was at 07:55 AM ----------
Oh and make sure USB debugging is Off when doing the above. USB debugging should always be Off... At least till ur pc detects ur phone.
Have the drivers installed on ur system before u are troubleshooting.
--
Sent from my Samsung S3 (GT-i9300) using Tapatalk
Click to expand...
Click to collapse
I tried all of that and nothing, pc just charge phone, no notification But, yesterday 2 times on charging after half hour via USB I got notification in windows: unknown hardwere or something like that ang nothing with drivers. In device manager not have anything about samsung and unknown devices.
webmar said:
I tried all of that and nothing, pc just charge phone, no notification But, yesterday 2 times on charging after half hour via USB I got notification in windows: unknown hardwere or something like that ang nothing with drivers. In device manager not have anything about samsung and unknown devices.
Click to expand...
Click to collapse
Did you download and install "Samsung USB drivers for mobile phones"? Any version should work. Make sure u install the drivers and reboot your machine.
--
Sent from my Samsung S3 (GT-i9300) using Tapatalk
Yes, instaled and reinstaled drivers and Kies.
webmar said:
Yes, instaled and reinstaled drivers and Kies.
Click to expand...
Click to collapse
In my case, post#8 works!
UART - >modem
USB - > PDA
khaaba said:
In my case, post#8 works!
UART - >modem
USB - > PDA
Click to expand...
Click to collapse
That not work for me. Selected same but not work.
webmar said:
That not work for me. Selected same but not work.
Click to expand...
Click to collapse
while saving after selecting SUB -> PDA, phone should boot automatically.
but my phone resets the both options to MODEM. I dunno why.

Categories

Resources