i just replaced my screen in my evo 3d for the second time after getting a faulty replacement and not i seem to be stuck in a boot loop. i had it booting 100% fine before i put in the new screen so i have no idea whats wrong with it. i grounded myself for the whole process so i really dont think i fried anything and i was careful with reassembling it as usual. but now it just gets stuck at the white htc screen ive tried flashing it with fast boot, and ive tried flashing it with the ruu which installed completly but its still stuck in the loop is there anything else i can try.
Is the screen from HTC or some cheap China knock off brand?
DjDom said:
Is the screen from HTC or some cheap China knock off brand?
Click to expand...
Click to collapse
LOL!
HTC is in China, a.k.a. Taiwan.
ramjet73
DjDom said:
Is the screen from HTC or some cheap China knock off brand?
Click to expand...
Click to collapse
its a screen i got out of another evo 3d that wouldnt power on
I am experiecing the exact same issue 1.40 hboot, s-off revoloutionary... Phone was fine aside from the digitizer touching itself randomly. Just replaced screen and can only get into bootloader, otherwise just bootloop. Have 4ext recovery, can not boot into it.
Can you flash pg86img's?
Maybe you should try the ruu
Sent from my PG86100 using xda app-developers app
Suggested ruu? I have not flashed one ever.
---------- Post added at 10:02 PM ---------- Previous post was at 09:49 PM ----------
I am changing back to my old screen to see if its just something crazy with the replacement used one I got. I also tried flashing the boot.img from the rom I am running with no success. Will post back after swapping old screen back in.
---------- Post added at 10:14 PM ---------- Previous post was at 10:02 PM ----------
It is booting...WTH... Is it a potential driver mismatch with my old radio and hboot version, or is this screen just a piece of crap?
mcss86 said:
Suggested ruu? I have not flashed one ever.
---------- Post added at 10:02 PM ---------- Previous post was at 09:49 PM ----------
I am changing back to my old screen to see if its just something crazy with the replacement used one I got. I also tried flashing the boot.img from the rom I am running with no success. Will post back after swapping old screen back in.
Click to expand...
Click to collapse
Related
Hey guys, got a question here...
I flashed prl00001 and now when I update prl through settings to get back on sprint it still reads 00001 even after profile update and reboot. Done this multiple times, starting to get worried about my contract being cancelled... Any ideas? Thanks
Which way did I use to put it on. I used it for a few days but it did not do all that good for me so I just used the epst and that's it. Make sure u r on a sence rom with epst
My 3D Shooter not yours!!
Yeah I'm on steel ROM 2.5 which is sense... I flashed it by dialing ##747# like usual. Trying to get back I use system update prl... Tried renaming prl file just in case it was getting in the way but no dice...
---------- Post added at 07:51 PM ---------- Previous post was at 07:49 PM ----------
Well strangely I tried again and it finally worked... After 20-some times... Ha ha
Every since i did a tituatam backup my home button always viberate but it doesn't go back to home screen or anything. How can you get that to work again ? Thanks
maybe stop rooting and modding your phone if you don't know what your doing
netter159 said:
maybe stop rooting and modding your phone if you don't know what your doing
Click to expand...
Click to collapse
nah , but i'm still looking for a answer though . Thanks for helping .
just do another "tituatam backup" and it should "viberate" harder so that your phone falls of your desk, and softbreaks enabling you to reflash the rom. Your welcome.
---------- Post added at 08:30 PM ---------- Previous post was at 07:34 PM ----------
have you tried reflashing the rom again?
netter159 said:
just do another "tituatam backup" and it should "viberate" harder so that your phone falls of your desk, and softbreaks enabling you to reflash the rom. Your welcome.
---------- Post added at 08:30 PM ---------- Previous post was at 07:34 PM ----------
have you tried reflashing the rom again?
Click to expand...
Click to collapse
-_- i cant get a simple answer ? .
RazKidd said:
-_- i cant get a simple answer ? .
Click to expand...
Click to collapse
learn to read kid. I posted it above, but i'll repost it just for you.
"just do another "tituatam backup" and it should "viberate" harder so that your phone falls of your desk, and softbreaks enabling you to reflash the rom. Your welcome."
Im still trying to get over that signature......maybe if you do another "tituatam backup" while holding your home button it will remember to back that up too...
i agree,def another tititatitiiatuuuam backup. Get the new version too. If he only spent as much time thinking about what he types, he might get worthwhile responses.
Can you damage the device at all doing this? Also if I do this, and it went wrong, would I have to RUU again? Another question, I am on the stock ICS OTA and its rooted, is that where I need to be to do this?
It is possible but you have to be pretty stupid to mess it up. Just touch the pins that it says to. It might take awhile to get the timing right but you should have no issues
Sent from my ADR6425LVW using Tapatalk 2
Evocm7 said:
It is possible but you have to be pretty stupid to mess it up. Just touch the pins that it says to. It might take awhile to get the timing right but you should have no issues
Sent from my ADR6425LVW using Tapatalk 2
Click to expand...
Click to collapse
Well it's not so much that I don't think I could do it, I just wondered if there is any risk. If you do mess up, I am guessing you would have to RUU right?
Stock rooted is the best possible place to be when doing it. Just use an insulated wire and you'll be fine. As for the timing, I've had the best luck basically just machine-gunning it. When I actually wait the 1.75 seconds, it never seems to work.
---------- Post added at 03:24 PM ---------- Previous post was at 03:23 PM ----------
Mrdroid921 said:
Well it's not so much that I don't think I could do it, I just wondered if there is any risk. If you do mess up, I am guessing you would have to RUU right?
Click to expand...
Click to collapse
No. Just pull up the troubleshooting page at unlimited.io and close to the bottom they have recovery steps. Just follow them and you'll be right back where you were.
EDIT: One more thing...back up your external SD card. It's supposed to restore it, but it's only been about 50% successful for me.
shrike1978 said:
Stock rooted is the best possible place to be when doing it. Just use an insulated wire and you'll be fine. As for the timing, I've had the best luck basically just machine-gunning it. When I actually wait the 1.75 seconds, it never seems to work.
---------- Post added at 03:24 PM ---------- Previous post was at 03:23 PM ----------
No. Just pull up the troubleshooting page at unlimited.io and close to the bottom they have recovery steps. Just follow them and you'll be right back where you were.
EDIT: One more thing...back up your external SD card. It's supposed to restore it, but it's only been about 50% successful for me.
Click to expand...
Click to collapse
as long as you only connect the two circuits it tells you too all will be fine.. i helped someone who was nervous about hitting the other circuits so i had him cover the ones you dont want to touch with electrical tape if your that worried about. but all will be well if you follow instructions. the wire trick is a crucial part of the control bear procedure..
I actually screwed mine up because I didn't realize I was touching Pin1 to the pin above GND, I started it correctly but since it took a lot of attempts I forgot which pin I was using. It didn't immediately screw up anything but I found that my data connection was constantly dropping out, even when I went back to stock and S-On'd. I brought it into Verizon and they suggested a factory reset, which I said I had done multiple times and then they said they didn't know what else to do so I got a new one
There is no risk on the software side in the actual s-off process that I know of.
The only other risk would be physically damaging the phone.
Someone pressed to hard with the wire and damaged the pins on the motherboard.
Sent from my HTC Rezound
I've been running cm10 for the past week or more. Last night phone powered off randomly, and when restarted came up with message saying the modem won't power on, starting rsd protocol, battery too low to flash. its been plugged in all night and says the same thing. ive factory reset in recovery mode, that didnt work. obviously cant sbf because the phone thinks the batt is dead. ??? phone wont turn on at all unless plugged into the wall
can you get into recovery? if so, it charges while in recovery.
Lorenzo VonMatterhorn said:
can you get into recovery? if so, it charges while in recovery.
Click to expand...
Click to collapse
I can, left it for a while and got the same message
Try another fully charged battery.
tallyforeman said:
Try another fully charged battery.
Click to expand...
Click to collapse
Or another battery I had my phone do the same thing ended up having to buy another battery and it was cm10 when it happened
P.S. there's a pretty good deal on anker atrix 1800mAh x2 w/ external charger I love having the two batteries and the external charger and for 25 bucks on Amazon you can't go wrong
don't be scared it's only a phone
ogd x d2g x2 gs3
old ladies ^
if you are going to root, you should have, atleast one of these three
1 spare battery
2 spare battery charger
3 Motorola Programing Adaptor by Team Black Hat
---------- Post added at 02:50 PM ---------- Previous post was at 02:48 PM ----------
Lorenzo VonMatterhorn said:
can you get into recovery? if so, it charges while in recovery.
Click to expand...
Click to collapse
BSR(DX2 system recovery) not android stock recovery
tbc
---------- Post added at 02:54 PM ---------- Previous post was at 02:50 PM ----------
3 things every Android person must have-Tomsgt123
bad bone said:
Or another battery I had my phone do the same thing ended up having to buy another battery and it was cm10 when it happened
P.S. there's a pretty good deal on anker atrix 1800mAh x2 w/ external charger I love having the two batteries and the external charger and for 25 bucks on Amazon you can't go wrong
don't be scared it's only a phone
ogd x d2g x2 gs3
old ladies ^
Click to expand...
Click to collapse
sd_shadow said:
if you are going to root, you should have, atleast one of these three
1 spare battery
2 spare battery charger
3 Motorola Programing Adaptor by Team Black Hat
---------- Post added at 02:50 PM ---------- Previous post was at 02:48 PM ----------
BSR(DX2 system recovery) not android stock recovery
tbc
---------- Post added at 02:54 PM ---------- Previous post was at 02:50 PM ----------
3 things every Android person must have-Tomsgt123
Click to expand...
Click to collapse
i see that now. my friend has his old dx im going to switch the batteries tonight. i leave for boot camp on monday so i dont have time to get something shipped.
edit: also does anyone know what "modem did not power on (2)" means
So I recently got a new LG K7. So being a complete idiot I did not back up my phone, then I proceeded to root it with kingroot then because it only has 8gb of storage I thought "well I really want to get GTA SA on my phone so ill just delete a couple of things in there to make it work." So I deleted a ton of Google play stuff and when I realized I would not be able to accomplish my goal I found out I messed up Google play for good. Fine I said I'll just factory reset. But when I factory reseted it would so the normal checking for connection thing except that it never ends (i left it sitting like that for a full 24 hours) so... yeah... my phone is basically screwed up. I took it to Tmobile to see if they could help but they pointed me here so now I'm just seeing if any of you can help. Thanks -Daniel
So since you messed up one of the valuable components of Google services, the Only option you have is to flash your firmware to the default firmware of your phone. Hope that helps!
Did you find the stock firmware? Did you also try to reflash gapps
NotAgain!!!!!! said:
Did you find the stock firmware? Did you also try to reflash gapps
Click to expand...
Click to collapse
Yu ever get it
I can help you fix it if you still need help
I may be in need of your expertise as [email protected] My situation is identical to his as i did the same to my girlfriends phone. In that after a hard reset, it won't get past the connectivity setup screen. Would greatly appreciate your help. Thanks in advancer
@goitalone .. Was wondering if you can help in getting my girls lg k7 up and running. It gets to the connectivity setup screen but never connects. Id truly appreciate any help. Thanks in advance:cyclops:
---------- Post added at 09:47 PM ---------- Previous post was at 09:45 PM ----------
[/COLOR @goitalone .. Was wondering if you can help in getting my girls lg k7 up and running. It gets to the connectivity setup screen but never connects. Id truly appreciate any help. Thanks in advance:cyclops:
DarkOn3 said:
@goitalone .. Was wondering if you can help in getting my girls lg k7 up and running. It gets to the connectivity setup screen but never connects. Id truly appreciate any help. Thanks in advance:cyclops:
---------- Post added at 09:47 PM ---------- Previous post was at 09:45 PM ----------
[/COLOR @goitalone .. Was wondering if you can help in getting my girls lg k7 up and running. It gets to the connectivity setup screen but never connects. Id truly appreciate any help. Thanks in advance:cyclops:
Click to expand...
Click to collapse
text me:
321-252-8858
or email:
[email protected]
---------- Post added at 04:01 AM ---------- Previous post was at 03:52 AM ----------
goitalone said:
text me:
321-252-8858
or email:
[email protected]
Click to expand...
Click to collapse
NM, sent you pm