awedel said:
I recently performed the steps to update my RAZR MAXX (XT-912 CDMA) to the OTA JB update. I had no issues. I obtained Root privileges and installed the most recent version of Safestrap for my phone (3.11). No problems detected. I then booted into Safestrap recovery and created a new ROM slot. Installed Jellycore V1.5 to it as well as Gapps. Booted to that slot and NOTHING. The screen just goes black after the Safestrap screen. So I booted back into Safestrap recovery and tried to restore my backup to that slot...same result. When the phone is rebooted, it goes to the Safestrap screen where you can select continue or recovery. If I continue (by selection or waiting the 10 seconds) the screen just goes black. I left it that way overnight thinking it might take a while but no. I've tried reinstalling Safestrap, different ROMS, and reinstalling ROMS. Any ideas? Because I need my AOKP.
Sent from my DROID RAZR MAXX using xda app-developers app
Click to expand...
Click to collapse
okay soo i found this thread and it only had 2 members and sorry if this is a no no,
but i didn't get a reply so i thought i would start a new thread
.. above is the problem that the original thread was created for and below is my problem
..bear with me, i am new to rooting the razr maxx ... i have rooted an htc thunderbolt, 3 gNexs, 2 nexus 7, and 2 galaxy s3s but i am havingw trouble with problem very similar to yours... but with a twist, i cant seem to remember all the the steps i took to produce this problem, as i was rooting my buddies razr maxx over super bowl weeekend and havent picked it up since ..... til now ... but anyways .. i did obtain root and had safestrap 3.11 installed... ok for starters the phone for one will not power on at all unless i plug it into a charger ... and when i do that i see the dual core screen and then it brings up the safestrap diabled screen and gives the option to press the menu button to reboot into recover or press the search button (or wait 10 seconds) to continue... when i press the menu button it goes to the black screen like u said ... when i wait 10 seconds it goes to the black screen and when i press the search button it goes to the black screen ... and then i end up having to use the volume down and power button to power it off (or if i unplug the charger it also powers off) ... when i plug it in again it automattically turns on and goes to the dual core screen and starts the process over ... i am however still able to get in to the boot menu ... and i tried to go into recovery mode that way and now the screen is stuck on the dual core screen with it plugged into the wall charger.... im thinking i have multiple issues ... one battery issue and i must have went wrong somehwere trying to flash a rom ...but wnho knows .. not me lol .... please please help ... we can do a google hangout and try to resolve this issue if you are willling ..... thanks in advance
funkme021 said:
okay soo i found this thread and it only had 2 members and sorry if this is a no no,
but i didn't get a reply so i thought i would start a new thread
.. above is the problem that the original thread was created for and below is my problem
..bear with me, i am new to rooting the razr maxx ... i have rooted an htc thunderbolt, 3 gNexs, 2 nexus 7, and 2 galaxy s3s but i am havingw trouble with problem very similar to yours... but with a twist, i cant seem to remember all the the steps i took to produce this problem, as i was rooting my buddies razr maxx over super bowl weeekend and havent picked it up since ..... til now ... but anyways .. i did obtain root and had safestrap 3.11 installed... ok for starters the phone for one will not power on at all unless i plug it into a charger ... and when i do that i see the dual core screen and then it brings up the safestrap diabled screen and gives the option to press the menu button to reboot into recover or press the search button (or wait 10 seconds) to continue... when i press the menu button it goes to the black screen like u said ... when i wait 10 seconds it goes to the black screen and when i press the search button it goes to the black screen ... and then i end up having to use the volume down and power button to power it off (or if i unplug the charger it also powers off) ... when i plug it in again it automattically turns on and goes to the dual core screen and starts the process over ... i am however still able to get in to the boot menu ... and i tried to go into recovery mode that way and now the screen is stuck on the dual core screen with it plugged into the wall charger.... im thinking i have multiple issues ... one battery issue and i must have went wrong somehwere trying to flash a rom ...but wnho knows .. not me lol .... please please help ... we can do a google hangout and try to resolve this issue if you are willling ..... thanks in advance
Click to expand...
Click to collapse
Okay okay.
Sounds like you got a flashing problem.
Go back to stock via RSD Lite and restart the procedure.
Also i would recommend u using BMM
Tell me your progress (PM or post here)
C ya !
Sent from my Galaxy Nexus using xda app-developers app
Yeah I like to flash that's my flashing problem HAHAHA .. I appreciate the help and yes I will definitely keep u update but it won't be til later on ... Otw to a job interview ... WML! But I am on familiar with RSD and BMM would you to be my best bet to catch up with my lack of knowledge?
okay the only problem i have is that the phone wont boot up in fastboot mode unless i have it connected to a wall charger as the computer usb port doesnt charge it fast enough ... and it shuts down if i unplug it from a wall charger ... and to run RSD you have to be in fastboot mode ... any ideas on a work around?
Connect to wall charger and wait for full charge ... if still shutting down you have a battery issue.
navi7512 said:
Connect to wall charger and wait for full charge ... if still shutting down you have a battery issue.
Click to expand...
Click to collapse
I must have a battery issue which is very weird because I didn't prior to the problem
If it's a battery issue this should help you flash and the restore your phone it's a lifesaver I have 1 and it works even if I don't have a battery plugged in... http://shop.teamblackhat.info/Factory-Adapters-motadapt.htm
Related
Hey guys, I recently found an alternative way to fix the low battery problem when your in AP Fastboot and able to get it to charge without the soldering of usb cable or the factory cable. So for those who do not want to open up their razrs or pay 40 bucks for a cable use my method.
-Make sure you have the charging cable connected to the phone and the cable to an outlet not an computer.
-While in the ap fastboot screen with the low battery problem, just push & hold Vol - and Vol+ and power buttons at the same time for 10 seconds
-Then IMMEDIATELY press and hold Vol - and Vol+ for 10 seconds to get back to the boot menu.
-Then once in the boot menu go down the the one option that has the word tools on it which is the last one.
-If it does not do anything just press volume up or down and go back to the tools and click power (enter) again.
-Then you should be boot to the M logo.
-Then after a bit you will be presented to an battery icon charging your phone!
-After a good charge up to 50% or so download the program called
New Link
http://www.droidrzr.com/index.php/topic/2248-droid-razr-utility-16-contains-612181-fastboot-files/
-Download that program and make sure your phone is back in AP fastboot and your battery should say OK meaning you can now program again.
-From there run the Droid RAZR Utility you just download it and choose option 1 and let it do its thing.
-Once done you should have the original stock rom and if you had root you must re-root it.
-Please message back for any questions! I am happy to help because I know how frustrating this is!
vel0city said:
Hey guys, I recently found an alternative way to fix the low battery problem when your in AP Fastboot and able to get it to charge without the soldering of usb cable or the factory cable. So for those who do not want to open up their razrs or pay 40 bucks for a cable use my method.
-Make sure you have the charging cable connected to the phone and the cable to an outlet not an computer.
-While in the ap fastboot screen with the low battery problem, just push & hold Vol - and Vol+ and power buttons at the same time for 10 seconds
-Then IMMEDIATELY press and hold Vol - and Vol+ for 10 seconds to get back to the boot menu.
-Then once in the boot menu go down the the one option that has the word tools on it which is the last one.
-If it does not do anything just press volume up or down and go back to the tools and click power (enter) again.
-Then you should be boot to the M logo.
-Then after a bit you will be presented to an battery icon charging your phone!
-After a good charge up to 50% or so download the program called
Droid RAZR Utility I can't post the link but it is in our forums so just search for it. If pm and I will give you the Link.
-Download that program and make sure your phone is back in AP fastboot and your battery should say OK meaning you can now program again.
-From there run the Droid RAZR Utility you just download it and choose option 1 and let it do its thing.
-Once done you should have the original stock rom and if you had root you must re-root it.
-Please message back for any questions! I am happy to help because I know how frustrating this is!
Click to expand...
Click to collapse
This really works for corrupted systems after a flash failure without a working fastboot?
Sent from my XT910 using Tapatalk
Great Job! Only wish that I knew about this 3 weeks ago! I took the back off and ended up glueing it back on and did a warranty exchange. I hope they don't say anything!!!
Again Great Job!!!!
Sent from my DROID RAZR using xda premium
pedrotorresfilho said:
This really works for corrupted systems after a flash failure without a working fastboot?
Sent from my XT910 using Tapatalk
Click to expand...
Click to collapse
As long as once it is plugged in and the screen comes up in the AP Fastboot it will work. Just hold power plues volume up and down then once that turns off immediatley press the volume up and down and it will boot you right to the boot menu. But just wondering what shows up for you if it is not the fastboot?
I can't get it to work, after I select BP Tools, it flashes the Motorola Logo and goes back to the AP Fastboot screen again. I don't think it works if you formatted \System.
renx0 said:
I can't get it to work, after I select BP Tools, it flashes the Motorola Logo and goes back to the AP Fastboot screen again. I don't think it works if you formatted \System.
Click to expand...
Click to collapse
exactly. for those that got cut off as the phone was in the process of flashing, i dont think it will boot to any phone charging icon because there's no software on the device. I've been trying for a week now
vel0city said:
Hey guys, I recently found an alternative way to fix the low battery problem when your in AP Fastboot and able to get it to charge without the soldering of usb cable or the factory cable. So for those who do not want to open up their razrs or pay 40 bucks for a cable use my method.
-Make sure you have the charging cable connected to the phone and the cable to an outlet not an computer.
-While in the ap fastboot screen with the low battery problem, just push & hold Vol - and Vol+ and power buttons at the same time for 10 seconds
-Then IMMEDIATELY press and hold Vol - and Vol+ for 10 seconds to get back to the boot menu.
-Then once in the boot menu go down the the one option that has the word tools on it which is the last one.
-If it does not do anything just press volume up or down and go back to the tools and click power (enter) again.
-Then you should be boot to the M logo.
-Then after a bit you will be presented to an battery icon charging your phone!
-After a good charge up to 50% or so download the program called
Droid RAZR Utility I can't post the link but it is in our forums so just search for it. If pm and I will give you the Link.
-Download that program and make sure your phone is back in AP fastboot and your battery should say OK meaning you can now program again.
-From there run the Droid RAZR Utility you just download it and choose option 1 and let it do its thing.
-Once done you should have the original stock rom and if you had root you must re-root it.
-Please message back for any questions! I am happy to help because I know how frustrating this is!
Click to expand...
Click to collapse
dude your a life saver! thank you!!!
solution
I tried to do so but did not work I tried to boot straight to the battery also did not work had to own a cable faser
mestisso79 said:
I tried to do so but did not work I tried to boot straight to the battery also did not work had to own a cable faser
Click to expand...
Click to collapse
did you try the above tutorial? worked fine for me a couple hours ago
jaredakelly said:
did you try the above tutorial? worked fine for me a couple hours ago
Click to expand...
Click to collapse
Definitely didn't work. When that m logo comes up, it disappears and the screen goes off. The charging icon does not show.
Sorry for the late reply but it is good to hear this method to work for jaredakelly . For those who are having problems did you have the phone charging in the wall outlet and not on a computer usb? The best steps is to choose the the tools option then just let the phone boot to the m logo then just leave it there on the wall outlet. Make sure you are using the Motorola usb cable that came with your phone and its usb adaptor that might make a difference.
I just tried this tut and it works as far as I can tell I am at the screen for battery charging but there is a big "?" in the center, the phone doesnt know what level its at lol..
I suggest you space out and make your original steps in bigger and bolder text for the specific buttons because I almost missed the power + vol down + vol up and was just pressing the volume buttons
This thread should be stickied!
Yeah sorry if my instructions were not to clear this is my first time posting anything like this on this site, but I am glad to hear it is working for you too. I don't even have this phone lol , it was my friend's and he had it stuck on the fastboot so I messed around with it and in the end this was the result.
yep
i think my battery is too low to attempt this i got it on 3 times and tried to fastboot restore but battery kept dying before completion so i guess im just screwed
no you should be fine because as long as the power cable is still plugged in it should work regardless of the low battery level. I did this on my friend's phone with 0% battery.
renx0 said:
I can't get it to work, after I select BP Tools, it flashes the Motorola Logo and goes back to the AP Fastboot screen again. I don't think it works if you formatted \System.
Click to expand...
Click to collapse
I have the same problem :/
This method worked for me! Your are the MAN OP!
Sent from my DROID RAZR using XDA
I think this should be stickied
Sent from my DROID RAZR using XDA
Well this got on xda front page
Sent from my DROID RAZR using XDA
Not a very good success rate for being on the front page. I'm going to try it later, though I think that I tried something like this before and it didn't work. I know that I have read this somewhere else.
I rooted my phone the other day using super one click 2.3 and left it just rooted due to cwm in my rom manager app not showing my phone model for whatever odd reason. Tonight I did the most stupidest thing and decided to pick nexus 4G in rom manager and downloaded CM10 ICS rom from rom manager itself and as soon it finished downloading I pressed install with dalvik cache wipe checked and now my phone is just stuck on boot screen that say "GALAXY S 4G exclusively from T-Mobile"
I tried to hard reset by pressing home/vol up,down/power button but the screen just goes black for about 3 seconds then the same "GALAXY S 4G exclusively from T-Mobile" screen come on and it just stay there. I also tried to plug in the phone to my laptop but the phone is not recognized anymore and nothing happens.
This is the only phone I have and I am lost. I really need my phone back. What do I need to do?
please HELP:crying:
CyberGmonster said:
I rooted my phone the other day using super one click 2.3 and left it just rooted due to cwm in my rom manager app not showing my phone model for whatever odd reason. Tonight I did the most stupidest thing and decided to pick nexus 4G in rom manager and downloaded CM10 ICS rom from rom manager itself and as soon it finished downloading I pressed install with dalvik cache wipe checked and now my phone is just stuck on boot screen that say "GALAXY S 4G exclusively from T-Mobile"
I tried to hard reset by pressing home/vol up,down/power button but the screen just goes black for about 3 seconds then the same "GALAXY S 4G exclusively from T-Mobile" screen come on and it just stay there. I also tried to plug in the phone to my laptop but the phone is not recognized anymore and nothing happens.
This is the only phone I have and I am lost. I really need my phone back. What do I need to do?
please HELP:crying:
Click to expand...
Click to collapse
Okay, okay relax and stay calm first and foremost. I assure you, we've all been there (at least I have been lol). Needless to say, it sounds like you can fix this...which is good! I suggest you first head over to this thread: http://forum.xda-developers.com/showthread.php?t=954509 and download the toolbox. Once its downloaded, install the necessary drivers if you have not already. After that, you need to get your phone into download mode. There are a few ways to do this, and people prefer going about it in different ways...I'd suggest taking out your battery, and then popping it back in and holding the power on and volume up button at the same time and hopefully it will boot into download mode (it'll be yellow). If that doesn't work after a few minutes, remove the battery again, pop it in and try holding the power, the volume up and the little "arrow up" soft key at the bottom of the screen and hopefully this time it will go into DL mode. Once you're in DL mode, connect your phone to the computer and use the toolbox to flash to stock. This will bring your phone back to factory conditions and you'll be set to go. Be sure not to remove your phone while its flashing back to stock until you are given the green light. Good luck!
Xenoism said:
Okay, okay relax and stay calm first and foremost. I assure you, we've all been there (at least I have been lol). Needless to say, it sounds like you can fix this...which is good! I suggest you first head over to this thread: http://forum.xda-developers.com/showthread.php?t=954509 and download the toolbox. Once its downloaded, install the necessary drivers if you have not already. After that, you need to get your phone into download mode. There are a few ways to do this, and people prefer going about it in different ways...I'd suggest taking out your battery, and then popping it back in and holding the power on and volume up button at the same time, once your screen turns on, remove your finger from the power button and continue holding the volume up button, and hopefully it will boot into download mode (it'll be yellow). If that doesn't work after a few minutes, remove the battery again, pop it in and try holding the power, the volume up and the little "arrow up" soft key at the bottom of the screen, when the screen comes on, let go of the power button and hopefully this time it will go into DL mode. Once you're in DL mode, connect your phone to the computer and use the toolbox to flash to stock. This will bring your phone back to factory conditions and you'll be set to go. Be sure not to remove your phone while its flashing back to stock until you are given the green light. Good luck!
Click to expand...
Click to collapse
Thanks for trying to help, but is not working. I tried both options multiple times but it would not go into DL mode. I can't believe I did this to my only phone
CyberGmonster said:
Thanks for trying to help, but is not working. I tried both options multiple times but it would not go into DL mode. I can't believe I did this to my only phone
Click to expand...
Click to collapse
Relax, relax...I assure you. Everything will be fine. Your phone isn't dead. Getting into DL mode can be a pain, and honestly it took me a few tries my first time also. You just need to find the correct combo. Try with phone off, holding volume up and down at the same time and then plug in the usb until the phone boots up into DL (hopefully). If this doesn't work, report back. If it does, go through the steps in my last post.
Xenoism said:
Relax, relax...I assure you. Everything will be fine. Your phone isn't dead. Getting into DL mode can be a pain, and honestly it took me a few tries my first time also. You just need to find the correct combo. Try with phone off, holding volume up and down at the same time and then plug in the usb until the phone boots up into DL (hopefully). If this doesn't work, report back. If it does, go through the steps in my last post.
Click to expand...
Click to collapse
Another thing to try, pull battery, SIM card and SD Card. Then plug in USB to computer, plug in to phone, pop the battery in holding down volume keys (up and down) -- its a little tricky but you get the hang of it. It was only consistent way my phone would go into DL mode.
Same Problem
CyberGmonster said:
I rooted my phone the other day using super one click 2.3 and left it just rooted due to cwm in my rom manager app not showing my phone model for whatever odd reason. Tonight I did the most stupidest thing and decided to pick nexus 4G in rom manager and downloaded CM10 ICS rom from rom manager itself and as soon it finished downloading I pressed install with dalvik cache wipe checked and now my phone is just stuck on boot screen that say "GALAXY S 4G exclusively from T-Mobile"
I tried to hard reset by pressing home/vol up,down/power button but the screen just goes black for about 3 seconds then the same "GALAXY S 4G exclusively from T-Mobile" screen come on and it just stay there. I also tried to plug in the phone to my laptop but the phone is not recognized anymore and nothing happens.
This is the only phone I have and I am lost. I really need my phone back. What do I need to do?
please HELP:crying:
Click to expand...
Click to collapse
I have almost the same problem.
Did you ever get the phone to go into DL mode?
TIA
Wrong forum. Go to galaxy s 4G forum.
Sent from my SGH-T959 using xda app-developers app
gknitz said:
I have almost the same problem.
Did you ever get the phone to go into DL mode?
TIA
Click to expand...
Click to collapse
What exactly is your problem? Please list your device model and what ROM or stock android version you were using when issue began. Any other info you have would be helpful.
Paranoid, sitting in a deep sweat...
samsgun357 said:
What exactly is your problem? Please list your device model and what ROM or stock android version you were using when issue began. Any other info you have would be helpful.
Paranoid, sitting in a deep sweat...
Click to expand...
Click to collapse
i rooted with superoneclick .... it couldnt verify shell but it rooted.... then i put a kernel on called sms-t959v-kj6-v0.1.0unsigned-update. then i tried to flash a rom called SamsungSlim-T959-4.2.1.Beta.1-OFFICIAL and thats where everything failed.... its stuck at the rom boot.... the screen says semaphore..... PLEASE PLEASE HELP.... I FELL LIKE IM DYING LOL MY EMAIL IS carlosts2009 at gmail.com.. or text 856 2 4 4 101 8
Your problem is the kernel is for the t959v galaxy s 4g and the ROM is for t959 vibrant. You can fix it in Odin with the stock firmware but we need to figure out which device you have. Do you have a stock front facing camera?
Sent from my SCH-I535 using xda premium
samsgun357 said:
What exactly is your problem? Please list your device model and what ROM or stock android version you were using when issue began. Any other info you have would be helpful.
Paranoid, sitting in a deep sweat...
Click to expand...
Click to collapse
im using a samsung galaxy s 4g running on gingerbread (the latest version for this phone) I got the instructions for how to root my phone from youtube and everything was good until today when it just got stuck on the boot screen. how can I fix this. I need a professionals assistance for this.
This is the Samsung vibrant t959 (3g). It looks like you have the Samsung galaxy s 4g t959v. These are totally different phones, you need the galaxy s 4g forums, these files for the vibrant will not work on your phone. Find the correct forum on xda website and flash back to stock for the t959v
Sent from my SGH-T959 using Tapatalk 2
If someone helped you, hit the thanks button!
I am desperate and have searched all over several forums to hopefully find someone else that has pulled this boner and had the same situation. I seem to be the only one ... LOL
I tried updating my Razr Maxx to Blur_Version.6.16.211.XT912.Verizon.en.US (actually is 6.16.215). I got a stock 211 on my Razr using RSD. It booted into recovery afterwards and I just went ahead and tried plashing 215 from the SD card. All seemed to be going well, phone rebooted afterwards and showed it was "Optimizing Apps". I walked off to do something and when I came back my Razr had a black screen. I tried to turn it on, No Go. I tried the Reboot (Vol - plus Power buttons), No Go. I tried to boot into recovery (power and both Vol buttons). No GO
The facts as I know them. I did not unroot before trying to flash 215. When I plug the charger in, I get the LED in the upper left for a moment and then it goes out. I have charged the phone for 7 hours and then tried all the boot up options (regular, soft reboot, Recovery). Nothing seems to work to turn my phone on so I can retry everything via RSD or whatever I need to do.
I know this is long, but I really need your help .... From all you guru's ...
Thanks in advance. I am at work so I may not be able to reply right away. Thanks again.
James
Anybody??
vip546 said:
I am desperate and have searched all over several forums to hopefully find someone else that has pulled this boner and had the same situation. I seem to be the only one ... LOL
I tried updating my Razr Maxx to Blur_Version.6.16.211.XT912.Verizon.en.US (actually is 6.16.215). I got a stock 211 on my Razr using RSD. It booted into recovery afterwards and I just went ahead and tried plashing 215 from the SD card. All seemed to be going well, phone rebooted afterwards and showed it was "Optimizing Apps". I walked off to do something and when I came back my Razr had a black screen. I tried to turn it on, No Go. I tried the Reboot (Vol - plus Power buttons), No Go. I tried to boot into recovery (power and both Vol buttons). No GO
The facts as I know them. I did not unroot before trying to flash 215. When I plug the charger in, I get the LED in the upper left for a moment and then it goes out. I have charged the phone for 7 hours and then tried all the boot up options (regular, soft reboot, Recovery). Nothing seems to work to turn my phone on so I can retry everything via RSD or whatever I need to do.
I know this is long, but I really need your help .... From all you guru's ...
Thanks in advance. I am at work so I may not be able to reply right away. Thanks again.
James
Click to expand...
Click to collapse
Can any body help me? or
Can you at least tell me if this is recoverable or do I need to us It as a paperweight????
You have try to charge your razr? It happens me one time.
Sorry I didn't read it, but you can do a factory cable to charge directly the battery
Enviado desde mi XT910 usando Tapatalk 2
Hi everyone,
I am writing in order to find a helping hint to rescue my Motorola Razr XT910...
I was just trying to install another ROM via BMM, wiped everything, tried to reboot to BMM again because I inserted a SD card...
Now it does not reboot anymore and does not show the BMM boot animation!
It shows the regular, red Motorola logo, and then nothing.. black..
What did I do wrong, or what can I do to revive it??? Is there any windows one click installer/tool/recovery program??
I have been using BMM for a while now and this never happened... I installed many roms but now it seems as if it is broken.
I would be so happy to get some hints. I haven't found some similar posts for this problem.
ejay
ejaybass said:
Hi everyone,
I am writing in order to find a helping hint to rescue my Motorola Razr XT910...
I was just trying to install another ROM via BMM, wiped everything, tried to reboot to BMM again because I inserted a SD card...
Now it does not reboot anymore and does not show the BMM boot animation!
It shows the regular, red Motorola logo, and then nothing.. black..
What did I do wrong, or what can I do to revive it??? Is there any windows one click installer/tool/recovery program??
I have been using BMM for a while now and this never happened... I installed many roms but now it seems as if it is broken.
I would be so happy to get some hints. I haven't found some similar posts for this problem.
ejay
Click to expand...
Click to collapse
there isn't a script tool for the xt910 because there are too many firmwares. The motorola logo means your bootloader is there, the black screen after means there isn't a ROM for it to boot up. It is curious that BMM hijack isn't showing up though. Have you taken the sd card out and tried booting it up again?
Anyways make sure you can get into stock recovery, if so, find the correct firmware for your xt910 (it is region specific.)
reinstall it with RSD lite(make sure you have plenty of battery.) Reroot, Reinstall BMM and restore your backup.
Draxin said:
there isn't a script tool for the xt910 because there are too many firmwares. The motorola logo means your bootloader is there, the black screen after means there isn't a ROM for it to boot up. It is curious that BMM hijack isn't showing up though. Have you taken the sd card out and tried booting it up again?
Anyways make sure you can get into stock recovery, if so, find the correct firmware for your xt910 (it is region specific.)
reinstall it with RSD lite(make sure you have plenty of battery.) Reroot, Reinstall BMM and restore your backup.
Click to expand...
Click to collapse
Thanks for your quick reply!
Right now I cannot get into ANY menu or something, I can press any button I want. After the "logo" it stays black. The phone also might not even be able to be connected to my computer. At least Microsoft Windows doesn't even show a new device when I connect it via USB, regardless if I have the correct drivers...
I dont know what to do... RSD didnt help me either. It wont find the phone...
ejaybass said:
Thanks for your quick reply!
Right now I cannot get into ANY menu or something, I can press any button I want. After the "logo" it stays black. The phone also might not even be able to be connected to my computer. At least Microsoft Windows doesn't even show a new device when I connect it via USB, regardless if I have the correct drivers...
I dont know what to do... RSD didnt help me either. It wont find the phone...
Click to expand...
Click to collapse
What logo?There is no logo in recovery...
Press vol-,vol+ and power button at the same time to get into recovery,select the option AP Fastboot and then you connect it via usb.
Sent from my Razr XT910
welder73 said:
What logo?There is no logo in recovery...
Press vol-,vol+ and power button at the same time to get into recovery,select the option AP Fastboot and then you connect it via usb.
Sent from my Razr XT910
Click to expand...
Click to collapse
Well, whenever you turn on your Razr, there is an initial red Motorola Logo. After that you usually touch the screen to boot into BMM (in case the green boot loader appears).
BUT... (of course I tried the VOL+ Vol- und Power button move) after rebooting it only shows the red Motorola Logo and then nothing but black.
ejaybass said:
Well, whenever you turn on your Razr, there is an initial red Motorola Logo. After that you usually touch the screen to boot into BMM (in case the green boot loader appears).
BUT... (of course I tried the VOL+ Vol- und Power button move) after rebooting it only shows the red Motorola Logo and then nothing but black.
Click to expand...
Click to collapse
I know there is a logo when you turn on the phone normally but you should turn it off and then turn it on with those three buttons,it must boot into recovery...
Sent from my Razr XT910
welder73 said:
I know there is a logo when you turn on the phone normally but you should turn it off and then turn it on with those three buttons,it must boot into recovery...
Sent from my Razr XT910
Click to expand...
Click to collapse
I have been trying this with these three buttons million times now. Until so far it always worked.. but now nothing happens anymore...
ejaybass said:
I have been trying this with these three buttons million times now. Until so far it always worked.. but now nothing happens anymore...
Click to expand...
Click to collapse
How long are you holding them down.. it can take a good twenty-thirty seconds sometimes. Mine is also finicky if I don't press them all down at the exact same time, it wont let me in then either.
If your getting the boot logo it is just really hard to believe you dont have stock recovery... can the device charge? If you hook it to a computer do you get the white led?
While it is Flashing M LOGO.... just keep the VOLUME DOWN AND POWER KEY Pressed...till it Flashes and Shutsdown....and immediately let go the Buttons and Immediately Again press Both the buttons... VOL DOWN+POWER Key
when you get to the FASTBOOT mode
you can follow this video
https://www.youtube.com/watch?v=LA8og7sbtBY
To unbrick your phone...Don't worry... its not broke
hrishi21007 said:
While it is Flashing M LOGO.... just keep the VOLUME DOWN AND POWER KEY Pressed...till it Flashes and Shutsdown....and immediately let go the Buttons and Immediately Again press Both the buttons... VOL DOWN+POWER Key
when you get to the FASTBOOT mode
you can follow this video
To unbrick your phone...Don't worry... its not broke
Click to expand...
Click to collapse
Thanks a lot for your reply! This video gave me hope I will try this as soon as I can...
ejaybass said:
Thanks a lot for your reply! This video gave me hope I will try this as soon as I can...
Click to expand...
Click to collapse
Now I am facing an issue that's really annoying. I can get into recovery (AP Fastboot) if the phone is connected to a power source. As soon as I unplug it, the screen turns black! When I connect the phone to my computer, the LED goes white and I cannot access AP Fastboot....
When no cable is connected to the phone I cannot access any recovery mode.
What is wrong here? Even if I connect the phone to the power source only, it shows the red Motorola logo all the time. It seems as if I cannot turn it off. Is there also a trick how to really turn it off and let the phone charge??
As the title says:
My phone: Motorola Razr Maxx / xt910
I have used 3.65 but i decided to update to 3.73 along since i hopped to CM11 M9 from CM11 M7
This is where my problems started.
I made a new partition, and activated it as "active" one.
I installed CM11 M9 onto it, and google apps after that.
I booted to the new system and setup my apps and everything was fine, then i shut down the phone.
After i re-started the phone today it was stuck on motorola dual core technology logo. (which happens before safestrap).
And i managed to get into bootloader and deleted the CM11 M9 partition and switched back to stock rom as active one.
Then i attempted to re-create the partition and when it was doing the partition, the phone went off (still had 96% battery left).
After starting the phone up again, it's stuck on infinite boot loop, and flashes the green safestrap BIOS for half a second.
Is there any way i can fix my phone?
Try to flash it with RSD Lite, but its loss of data :/
Thank you for answering
archie1988 said:
Try to flash it with RSD Lite, but its loss of data :/
Click to expand...
Click to collapse
That is least of my worries And i got all data backed up pretty well
Is there any step by step tutorial for this?
stefeman said:
Thank you for answering
That is least of my worries And i got all data backed up pretty well
Is there any step by step tutorial for this?
Click to expand...
Click to collapse
Go here: http://forum.xda-developers.com/showthread.php?t=2155576
And scroll to video named undbrick/restore/unroot via rsd lite.
On the first page [emoji6]
archie1988 said:
Go here: http://forum.xda-developers.com/showthread.php?t=2155576
And scroll to video named undbrick/restore/unroot via rsd lite.
On the first page [emoji6]
Click to expand...
Click to collapse
I can't even get to AP Fastboot.. the safestrap flashes upper area and ****s up before that
Enough with this ****.. I'll bring this **** to my ISP and pay something so they null it and re-install stock system..
Lesson of the day.. don't update safestrap lol
stefeman said:
I can't even get to AP Fastboot.. the safestrap flashes upper area and ****s up before that
Click to expand...
Click to collapse
Turn off the phone and while it's off press vol- vol+ and the power button at the same time.
If you do it right,you shouldn't see anything related to SS.
Sent from my Razr XT910
welder73 said:
Turn off the phone and while it's off press vol- vol+ and the power button at the same time.
If you do it right,you shouldn't see anything related to SS.
Sent from my Razr XT910
Click to expand...
Click to collapse
Done that multiple times and the screen just flashes on upper area of the screen and goes off..
I can't even power it on without plugging in a charger first.. If i unplug charger it flashes and goes off..
The battery is close to 96-98%
stefeman said:
Done that multiple times and the screen just flashes on upper area of the screen and goes off..
I can't even power it on without plugging in a charger first.. If i unplug charger it flashes and goes off..
The battery is close to 96-98%
Click to expand...
Click to collapse
What about the led light,is it white?
If it's white then your battery is too low,you must buy or make the factory cable to be able to flash the fastboot with Rsd lite.
Sent from my Razr XT910
welder73 said:
What about the led light,is it white?
If it's white then your battery is too low,you must buy or make the factory cable to be able to flash the fastboot with Rsd lite.
Sent from my Razr XT910
Click to expand...
Click to collapse
Led light is never shown.. =/