[Q] Locked Aoson M30 - Won't boot - Android Q&A, Help & Troubleshooting

Hi guys,
I have an Aoson M30 (rockchip 3066) and it now won't boot to the home screen.
It Just turns on to the company logo boot up screen (which is normal) but stays at this screen. It flashes the pattern over and over so the processor is obviously still running .
It should then go to the home screen but just continues to flash the boot screen.
I tried to reload the firmware but the Rockchips batch tool doesn't work either. It sees the tablet but stays at "pink" on the indicator screen. It doesn't turn green (which it needs to) so the firmware will not transfer to the tablet.
I have reset via the reset button, flattened and recharged etc but it wont start up
.
I tried booting holding the volume + and power buttons and it comes up with an image of 2 penguins? Then it shows a vertical android bot for a second before showing one lying down with a " !" symbol above it.
I guess the firmware is corrupted but without the ability to reload I fear I may have a brick!!!!
Any ideas?
Cheers
Charlie in New Zealand

charlieenz said:
Hi guys,
I have an Aoson M30 (rockchip 3066) and it now won't boot to the home screen.
It Just turns on to the company logo boot up screen (which is normal) but stays at this screen. It flashes the pattern over and over so the processor is obviously still running .
It should then go to the home screen but just continues to flash the boot screen.
I tried to reload the firmware but the Rockchips batch tool doesn't work either. It sees the tablet but stays at "pink" on the indicator screen. It doesn't turn green (which it needs to) so the firmware will not transfer to the tablet.
I have reset via the reset button, flattened and recharged etc but it wont start up
.
I tried booting holding the volume + and power buttons and it comes up with an image of 2 penguins? Then it shows a vertical android bot for a second before showing one lying down with a " !" symbol above it.
I guess the firmware is corrupted but without the ability to reload I fear I may have a brick!!!!
Any ideas?
Cheers
Charlie in New Zealand
Click to expand...
Click to collapse
Hi,
i had the same problem some time ago and the way I solved it was by flashing again the original rom.
Your issue might be the driver installatin on the PC to recognize the tablet as a M30. I had to use an XP to be sble to install properly the RK3066 drivers.
Also try tomuse another usb cable. The one it comes with the tablet is quite patchy and I had to use a good quaƱity one.
Dont give up, if you ger the endless logo loop I dont think it is bricked.
Good luck.

Related

[Q] Android tablet not booting up

Hello everyone,
I recently received an Innovatek Inno Pad 10 (chinese android tablet) as a gift and the problem is that the tablet does not boot up. When I got the tablet and turned it on, it showed me an android bootloader screen and then it brought me to the android logo boot screen where it would basically go into an infinite boot sequence. I have tried charging it fully and then turning it on, I have tried un-plugging the battery and plugging it back in. I even tried re-flashing the firmware on the device using a software supplied by the company (it was very hard to find and the company's support is not that great). The flashing process was completed successfully but the tablet would still go into an infinite boot loop (I even tried re-flashing it again with no luck). Here is the worst part, there was a u-boot-nand.bin file included with the program and I decided to try and flash the tablet using that file. Now the tablet's screen won't even turn on, but the power and charge buttons still light on. I think the bootloader got messed up. Does anybody have an idea how to get this tablet working? I have posted pictures of the tablet and its specs.
Thanks
John

help finding an A13 ROM

Hi!
I've been asked to "fix" a "broken" chinese tablet. The tablet won't boot; sometimes it get stucked at boot logo (some chinese brand I think), and sometimes get stucked at a black screen.
Power button+volume UP brings the layed-down-android-with-red-exclamation secreen, but no combination afterwards brings me the recovery menu. It also has a reset button on the backwards. I've pressed it several times, from 3 to 60 seconds, and it only resets like the reset button on a PC.
I've wiped data with some software I've found somewhere (android multi tools, a green DOS menu), but still I'm having the same issue.
I've read about reinstalling the firmware with phoenixcard, but I can't find the right one. I've uploaded some pictures to ask for help.
Thank you very much!
Try Livesuit 1.11.
I'm running FaaastJB v2.5 http://forum.xda-developers.com/showthread.php?t=2447819
Flashed a few ROM's using Livesuit and works great

Samsung Galaxy S4 WEIRD Problems (A must read for certified problem solvers)

Ok, so one night I was using my phone normally (Browsing. Watching YouTube, Playing Games) like everyone else does. Then all of a sudden it shuts off, but immediately turns on again without me pressing a button. (So basically it suddenly auto restarts on its own) This occured maybe 2-4 times (all in one night) until one time, it shuts off but doesn't turn on again (basically an automatic shutdown), so I tried turning it on again (Power button), then I got shocked because all of a sudden it enters a boot loop (Screen displaying this sequence : Samsung Galaxy S4 screen, my carrier logo screen, The encrypted screen (where you have to enter your encryption password) then again the Samsung logo but this time with the colors splashing from the background, then it shuts off again.) Sometimes after the boot loop sequence, it vibrates but never turns on again, sometimes it just turns off after the sequence. And as I try and try to get away from the boot loop, the sequence became shorter. So I'm guessing it's a battery problem, BUT my battery isn't bloated or deformed. I tried clearing the cache first, again the sequence got shorter (never going up to the carrier logo screen), then I tried formatting the data, still to no avail. Now, when I turn it on, It shows the Samsung logo screen for 2 seconds and shuts down.
I tried flashing it with ODIN thru Download mode BUT (HERE'S where another problem occured) :
My phone never get pass on the system.img.ext4 dialogue and my screen just goes blank. But ODIN still recognizes my phone. And when I remove the USB cable, ODIN says FAIL.
I'm sure the cable is working. I downloaded the firmware for my carrier (Tre 3).
What could be the real problem here?
Here is the description of my device :
Samsung Galaxy GT-I9505
Bought from Italy, Tre 3 carrier
Can I download a different region/carrier for my I9505 phone?
Advanced thanks for anyone who comments and I'm very sorry for my English. Thanks!
I would install TWRP recovery, boot to it, and use it to format data, which will remove the encryption. Then I would either push a rom to the phone via recovery or try to reinstall the stock firmware with Odin. Make sure that you run Odin as admin as well. The firmware must be the same version or newer. If you still have the stock recovery and can boot to it, then I think the build number of the currently installed firmware will be visible there. You should be able to use that to Google the correct version you need.
Hey it's me. Just posting a quick reply.
Thanks for replying to my post. Yesterday I successfully flash a rom to my GT-I9505 (Version 5.0.1 Italy HUI 3G). However it still didn't boot up. At first try it booted up to the first setup screen then just randomly shuts down. Then as I try to boot it up again, It just shuts down after the first Samsung logo (with the GT-I9505 logo), I can't boot into recovery cause it shuts down. I'm sure it's not a battery issue cause when I boot into download mode, it can stay in that screen for like 10 minutes. What could be the issue? I'm planning to disassemble my S4 sooner to see if something's wrong inside. Thanks again for the reply

HIMEDIA Q10 Pro Bricked after firmware upgrade - help!

I have a Himedia Q10Pro Android box that has been bricked by a firmware update. I followed the instructions (FAT32 drive, only update on root of drive) I was performing the firmware upgrade from 1.0.8 (Android 5.1) to 2.0.1 (Android 7) very carefully as instructed by the post in the forum, box is in a cool equipment area, fed from a clean UPS for power. Got the Android upgrade screen, progress bar was moving. Stepped away to help my daughter, and when I came back I was at the HIMEDIA boot screen. Left it to boot.. and waited.. and waited. Wouldn't go past that boot screen, left it a couple of hours. Then powered off and then back on, still stuck on the boot screen (says boot on the LCD display too).. left it an hour again, no go. Tried leaving it unplugged overnight (clutching at straws!).. no change.
I've tried the upgrade again, when pressing the upgrade button, the LCD changes to 0000, but still displays the HIMEDIA logo and no activity light on my USB thumb drive. Tried several thumb drives, all 3 USB ports, several firmware versions (including the 1.0.7 as suggested), and every combination.. no dice. Stuck on 0000 on the LCD and Himedia logo on TV if I've used the upgrade button.. stuck on boot on the LCD screen and Himedia logo on the TV if I haven't. There is a guy in youtube (can't post links yet, search 'Himedia Q10 pro bricked after upgrade to hmd2.0.1') who seems to have the exact same problem.
Any suggestions gratefully received.
Thanks
Does the power button blink red and white?
The same problem
The USB does not respond to a any USB flash disk
The same problems.. Guess it is bricked.
Bleh_KR said:
The same problems.. Guess it is bricked.
Click to expand...
Click to collapse
Solution..Open box -contact with rs232 an try with puty...Are work - stop elec. when open driver usb..

Black screen after Logo[GFive President G9]

Hello guys, I have run into a serious problem here! Please help me out..
I have a GFive President G9 Android running stock Jelly Bean 4.2.1 (ROOTED). I tried to install a boot animation through ROM Toolbox app, when I rebooted it, it didnt show any boot animation and booted straight to the home screen. So I just went into the ROM ToolBox app and restored the bootanimation backup I had created earlier to get the original GFive boot animation back.
However, when I rebooted, my phone showed the GFive Logo, and after it the screen went dark( The screen is backlit but doesnt display anything). It just stops there and doesnt do anything. Ive tried removing the battery but to no avail. For some reason I CAN'T ACCESS the RECOVERY or the DOWNLOAD MODE, as holding the power button and vol up etc still ends up in the same situation - Black backlit screen after logo. The phone isnt in a reboot loop or anything, it just stops at the black screen for eternity.
THE WORST PART, this phone probably has a damaged USB port, since I was previously able to charge it via the PC, but it wasnt detected in the PC. So I CANNOT CONNECT IT TO THE PC.
So is there anyway I could get this phone back alive? Is a factory reset possible? Please help me experts!! :crying:
P.S Custom TWRP is installed, but I cant access it
So there's no expert in this whole forum who has a solution for this? Because no reply means no one has an answer..
Incase theres no way out of this, please mention that.

Categories

Resources