Related
hi guys. my x10 froze at se boot and does nothing. i've read through almost all helpfull threads that are similar to my problem but the problem still persist. fyi, i booted to xrecovery, made a backup and i noticed that there were problems in backing up (md5 chcksum, i think). but the backup file was created. i restored using that file and now it is stuck at boot. i can't even turn the phone off. i've tried hard reset, tried using the sues, flashtoo and even pc tools but to no avail. this is due to the phone can't connect to usb. can anyone please help me.
You have do a factory reset and wipe cache?
how can i do that andres3d? are there any way for me to do that? i'm trying but the phone just can't go past the se boot. it's just stuck there. i can't even turn the phone off. the only way is to take out the battery.
Try this, enter into xrecovery and select "factory resect" first at all, then reboot.
I got stuck there too, and I haven't the xRec installed
You can download the SE Update Service (SEUS) and flash the original rom back to it.
Download the software and install, take off the battery, wait a little bit (30s or so), insert the battery back. DO NOT TURN ON THE PHONE YET.
Open the SEUS, choose the phone (X10) and click 'go', or 'ok', or whatever. Keep going and the software will tell you to plug the phone. Plug the phone turned off. When it's plugged, turn it on holding the back button until the software tells you to release.
Wait a few moments... and it's done. Turn on your phone, it should take a little longer to boot, but it's just the first time, then it boots normally.
It's quite easy to do when you know what to do
thanks in advance but i've tried both method and it still got me nowhere. first, i can't boot to xrecovery at all and second, the sues doesn't even detect my phone.
Did you try download a stock firmware from here and install by flashtool?
Do you have installed drivers from x10 to your PC?
I thing the only way is by flashtool, because you don't have xrecovery access l.
http://forum.xda-developers.com/showthread.php?t=872298
Sent from my X10 using XDA App
rota2903 said:
thanks in advance but i've tried both method and it still got me nowhere. first, i can't boot to xrecovery at all and second, the sues doesn't even detect my phone.
Click to expand...
Click to collapse
Your phone must be charged ¬¬
Leave him charging at wall for about 45-60min and then try to do the step-by-step
tnx
tnx guys. i'll try the methods that u guys suggested. i really hope that i don't have to send the phone back to the shop.
OMG. it was actually my cable!!! that's why i can't flash my phone. now the phone is back to it's original state. anyways, i would like to thank all of you guys that have given me great advice. thanks again guys.
[Q] {HELP} another x10 stuck at se boot part 2
rota2903 said:
OMG. it was actually my cable!!! that's why i can't flash my phone. now the phone is back to it's original state. anyways, i would like to thank all of you guys that have given me great advice. thanks again guys.
Click to expand...
Click to collapse
Hi all
Unfortunetly my case is 99% similiar as "Sony Ericsson XPERIA X10XPERIA X10 Q&A[Q] {HELP} another x10 stuck at se boot" but changing the cables doesn't help. The only thing which the phone respond is to hold back starting of booting what immidietly happening when i'm connecting the usb cable.
I had xrecover installed before but is not starting onto flashing mode.
Any ideas
Hi,
I have an Xperia X10 with Cyagenmod 6 (gingerbread 2.3.3) but it's broken. It won't boot any more. Some days ago it just went out, and it won't start up again. The phone behaves as if it freezes the moment android should load. Like if your computer would freeze in bios, unable to load your operating system.
I'm also not able to repair it with SEUS because although it recognizes the phone, it can't reset because the phone freezes just before the stage in witch it can reset.
I am kind of a noob with these things and therefore hope one of you guys could help me out. I'm not really looking foreward te buying a new phone already
Thanks!
Freekh
kinda same problem..
i'm removing battery, put back and after holding power the phone shows green led for short time and vibrates for a sec and that's.
add:
i've flashed it before the problem occurs.. flashed, phone booted up, everything normal.. put on usb for charging, changed language and time when it suddenly freezed
This is what happened to mine what country u in
sent with a geordie kiss using wb 2.3.3
what do you mean with "country"?
freekh said:
Hi,
I have an Xperia X10 with Cyagenmod 6 (gingerbread 2.3.3) but it's broken. It won't boot any more. Some days ago it just went out, and it won't start up again. The phone behaves as if it freezes the moment android should load. Like if your computer would freeze in bios, unable to load your operating system.
I'm also not able to repair it with SEUS because although it recognizes the phone, it can't reset because the phone freezes just before the stage in witch it can reset.
I am kind of a noob with these things and therefore hope one of you guys could help me out. I'm not really looking foreward te buying a new phone already
Thanks!
Freekh
Click to expand...
Click to collapse
Try re-flashing the stock rom using flashtool. That solves Every problem for me ^^
freekh said:
Hi,
...
I'm also not able to repair it with SEUS because although it recognizes the phone, it can't reset because the phone freezes just before the stage in witch it can reset.
...
Click to expand...
Click to collapse
not able to flash anything
blmn1337 said:
not able to flash anything
Click to expand...
Click to collapse
Why exactly are u unable to flash anything? Are you following the proper procedure?
Here's a guide fro using flashtool http://forum.xda-developers.com/showthread.php?p=10879507#post10879507
fawadmir said:
Why exactly are u unable to flash anything? Are you following the proper procedure?
Here's a guide fro using flashtool http://forum.xda-developers.com/showthread.php?p=10879507#post10879507
Click to expand...
Click to collapse
i've posted some logs in other thread
http://forum.xda-developers.com/showthread.php?t=1190540&page=2
umm.. Do u move your mobile when the flashing process is going on? The xperia USB slot is pretty sensitive. Moving the phone can cause it to lose connection and abort the flashing process
28/048/2011 21:48:10 - ERROR - Error flashing. Aborted
i always receive this error if i move my phone.
Notice if you hear the USB device unplug sound from your PC before this error occurs.
^^
fawadmir said:
umm.. Do u move your mobile when the flashing process is going on? The xperia USB slot is pretty sensitive. Moving the phone can cause it to lose connection and abort the flashing process
28/048/2011 21:48:10 - ERROR - Error flashing. Aborted
i always receive this error if i move my phone.
Notice if you hear the USB device unplug sound from your PC before this error occurs.
^^
Click to expand...
Click to collapse
it doesnt seem to be a connection-problem (no usb unplug sounds).
it seems that the phone is in a state, where bootup is not possible
But the phone is not required to boot during flashing. Did you try changing the USB slot on your PC? The one you're connecting your phone to? Try another slot. Sometimes that works too.
fawadmir said:
But the phone is not required to boot during flashing. Did you try changing the USB slot on your PC? The one you're connecting your phone to? Try another slot. Sometimes that works too.
Click to expand...
Click to collapse
same result. can't flash
Me too. Can't flash with Flashtool (latest version), even without moving my phone. It starts flashing, but the progress bar shows of no progress. After a while it just says Error - Abort Flashing. I tried all of my USB port, but nothing changes.
after doing and trying my battery got completely drained (red led blinking) so i left it on the wallcharger for ~1day..
then at sometime it managed to boot up itself.. i left it for charging till 100%
after that i did a few "wipe battery stats" in xrecovery and now it seems to work stable again..
is it possible that messed up battery stats could cause the problem?
Wow, that would be nice.
A question! Was the little led on while charging? Because when I put my phone in the loader, it turns green (as if the battery is completely empty) and after a while it just goes off (when it would normally turn red). Do you have that to?
Putting my phone in the loader now, and waiting till tomorrow! Hope this helps!
yea, i've noticed this with my phone too..
strange led behavior..try to plug the charger first (green led turns on, cant say whether its charging or doing anything else) and then put in the battery and wait
maybe you're lucky and the phone will boot
and report pls
I didn't work. I've put my phone in the loader for over 24 hours, but nothing happened.
But my phone wasn't completely drained. Perhaps that is a condition to make this work. The only question is, how do I drain my battery when I can't turn on my phone?
i have used an 5watt light bulb ^^
connected on + and - and then waited till light goes out
Wel, I connected a little lamp and waited until it went out. Then when I put my battery in my phone and pressed the ON button nothing happend, not even the green light flashing shortly.
When I put my phone in the loader the LED started flashing red. And that whent on for a while until it stoped, and the LED did nothing. Then I waited over 24 hours, but nothing has happend.
When I put my phone in the loader now, it's just like before, the green light burns a little while, then nothing..
it happened to me again.. freeze and then no boot.
but i think i know whats wrong. for my phone i can say, that the battery is ok and the rom/os aswell.
its hardware problem. something is screwed up inside the phone.
when i press the phone at randomly places and hold it + then pushing on-button it boots up
i will open it tomorrow
So, sort of long story, i'll cut it short
-Got an old X10, had stock 2.3.3
-Rooted it
-Did not unlock bootloader, got kinda scared.
-Tried to install FeraLab custom ROM, it failed probably because of sdcard permissions; i accidentally wipe /system /data /cache
-stuck at first Sony Ericsson screen
-Somehow managed to flash a 2.1 stock rom with flashtool, after an hour of different combinations of enterring flash mode and pulling the battery
-Tried to install FeraLab again, this time it went through
-After install, rebooted, phone shut down during boot up process
-Will not turn on at all. Even when plugged into a PC, wall, not plugged in, pulling battery, etc.
I think what happened is that FeraLab needed a newer baseband than the 2.1 stock rom had. Does anyone have any suggestions on how to get this sucker to even turn on? Not a single LED is on when plugged in, giving me the impression that it's not charging.
If the battery has drained out, it might take some time before it kicks in and indicates that it is charging.
If the ROM has failed somehow, it might not show that it is charging at all, but might be charging.
Either way: Let it charge "blindly" for a while, and see what happens.
Once it does boot up to some level or shows life-signs, let it charge fully before you'l attempt a ROM flash.
The flash/recovery mode needs a full battery, and reason is that the external power isn't used even when connected while in flash/recovery mode.
If you happen to be in bad luck, and the ROM failed as a result of a drained battery, you might have to charge the battery externally. Use an external battery charger made for 3.6 volts Lithium Polymer batteries, and make sure to align the + and - terminals properly.
I can recommend the multicharger from Powerbase, called C-734U:
http://www.powerbasehk.com/product.php?id=148
Using it myself to charge the X10 battery, as well as other batteries from other devices I have.
EDIT:
(For some reason, powerbase has taken back that it'll charge Lipo batteries, but when I bought mine, it was described as a li-ion, li-poly and Ni-MH charger, and it't ability to charge li-poly batteries was the very one reason to why I bought it.
I suspect PowerBase does not want to take responsibility if anything happens to the li-poly-batteries, as they are known to be more dangerous than other types.)
I've left it on the wall charger all night, no response or anything. Luckily, I bought a new battery a few days ago, so when that comes in, hopefully it will be charged enough for this thing to boot.
Do me a favour are u able to take screebshot of settings, about phone menu and post it here? Need to see ur baseband and kernel
Sent from my X10i using XDA
laneyofdeath said:
Do me a favour are u able to take screebshot of settings, about phone menu and post it here? Need to see ur baseband and kernel
Sent from my X10i using XDA
Click to expand...
Click to collapse
Dude his phone wont start up. How come he'll be able to take a screenshot
Sent from my LT26i using xda premium
king-iyokan said:
Dude his phone wont start up. How come he'll be able to take a screenshot
Sent from my LT26i using xda premium
Click to expand...
Click to collapse
Yeah, i'm not sure what he expected. But, good news! Now for some reason my phone started blinking red whenever I tried to turn it on! I guess the battery completely ran out or something. It also blinks every now and then when plugged in, so I guess it's charging. The previous owner of this phone said that it had some battery problems, so that's why I ordered that new battery. I'll let it charge for awhile and let you guys know what happens.
Okay, after getting my new battery, the phone will still not turn on. I think i've figured out two behaviors:
1. If the battery is nearly completely out of charge, it will flash a red light
2. If the battery has charge, it will not do anything at all.
Anyone know how to fix this?
While trying to turn on the phone, after long-press power button, do you get a flash from status led & short vibration?
From my XPERIA X10S v8.2 on kCernel @ 1.19ghz
ToledoJab said:
While trying to turn on the phone, after long-press power button, do you get a flash from status led & short vibration?
From my XPERIA X10S v8.2 on kCernel @ 1.19ghz
Click to expand...
Click to collapse
No vibration, the red LED flashes three times, and that is , as I said before, what happens when the battery seems to not have any charge. If I have a charged battery it does absolutely nothing.
Have you removed sim & sd card and tried. I know it sounds dumb but when I flashed a bad kernel I had to try to connect flash mode like 10 times. Finally I left the phone unplugged from pc, started flashtool and started flashing. I only put battery in phone just before holding back key. I never connected USB until tool said to dis-connect phone and connect in flashmode.
i wish you luck, I know how I felt when it went wrong
From my XPERIA X10S v8.2 on kCernel @ 1.19ghz
FireFreek said:
So, sort of long story, i'll cut it short
-Got an old X10, had stock 2.3.3
-Rooted it
-Did not unlock bootloader, got kinda scared.
-Tried to install FeraLab custom ROM, it failed probably because of sdcard permissions; i accidentally wipe /system /data /cache
-stuck at first Sony Ericsson screen
-Somehow managed to flash a 2.1 stock rom with flashtool, after an hour of different combinations of enterring flash mode and pulling the battery
-Tried to install FeraLab again, this time it went through
-After install, rebooted, phone shut down during boot up process
-Will not turn on at all. Even when plugged into a PC, wall, not plugged in, pulling battery, etc.
I think what happened is that FeraLab needed a newer baseband than the 2.1 stock rom had. Does anyone have any suggestions on how to get this sucker to even turn on? Not a single LED is on when plugged in, giving me the impression that it's not charging.
Click to expand...
Click to collapse
Try to flash any latest kernel via flashtool . Go for doomkernel . I think its software issue . Try this first .
Almost same here please help..
Last night battery ran out of charge & phone switched off.. then i plugged the charger it doesn't charge.. after some time i tried turning on.. Vibrates with the green LED but nothing happens then..
Note: This is not the 1st time i'm letting my phone drain, but facing this problem for the 1st time..
Rom : Spikelabs GB Gaming rom
Kernel : Ferakernel v23 beta6
I tried another battery, charger, data cable.. Tried flashing stock & spikelabs kernel., but of no use..
Any help is greatly appreciated..
Thanks in advance.. :good:
Something like that happened to me not long ago!
I was trying to flash some ROMs and I messed up then my phone wouldn't turn on!
But Miracously, I could flash a Stock 2.3.3 which fixed the problem!
At first, I used Sony PC Companion, which helped a lot- and after I screwed it for the second time, I used FlashTool-
I don't know if this was helpful, but I hope your x10 will be fixed soon!
yeah try the PC Companion first, it helped me too a couple of weeks ago
No luck...
Hi friends..
Tried to repair using PC companion, but was able to connect only in flash mode, unable to proceed software update..
I previously tried flashing stock GB using flashtool thrice. Still couldn't switch on the phone.. What else may i try..
Thanks friends..
ashok weird said:
Hi friends..
Tried to repair using PC companion, but was able to connect only in flash mode, unable to proceed software update..
I previously tried flashing stock GB using flashtool thrice. Still couldn't switch on the phone.. What else may i try..
Thanks friends..
Click to expand...
Click to collapse
try flashing kernel other than spikelabs (e.g. feravolt,doom,achotjan,zkernel..etc.)
sanababitz said:
try flashing kernel other than spikelabs (e.g. feravolt,doom,achotjan,zkernel..etc.)
Click to expand...
Click to collapse
Tried Ferakernel, Stock GB kernel, etc bro.. No luck..
Flashed Stock GB firmware more than 3 times still no luck :crying:
SEUS not working _ couldn't connect to network..
SUS does not have x10 enlisted
Went to 3 service shops at - Ritchie street, Chennai. They simply said harware issue (Short in board) and gave back the phone.
Now given at a better service centre. Will get back on monday it seems. Will update the status friends..
Thanks..
Here also they said the same reason friends.. Short in board..
Is there any way i could recover the phone???
Hi guys/girls/undecideds,
My phone made me a sad panda recently when it stopped booting correctly - on startup it vibrates as it should, the screen lights up, but does nothing more - it does NOT reach the sony-ericsson logo that comes up, and the light goes off. It continues to repeat this loop about once every five or so seconds.
Obviously, not being a total moron (i'm only like, 40% moron), my first thought was to reflash the software, but I can't, because every time I connect the phone to flashtool, it disconnects a couple of seconds later and obviously, the flashing fails.
Can you help me find my smile?
sodslaw said:
Hi guys/girls/undecideds,
My phone made me a sad panda recently when it stopped booting correctly - on startup it vibrates as it should, the screen lights up, but does nothing more - it does NOT reach the sony-ericsson logo that comes up, and the light goes off. It continues to repeat this loop about once every five or so seconds.
Obviously, not being a total moron (i'm only like, 40% moron), my first thought was to reflash the software, but I can't, because every time I connect the phone to flashtool, it disconnects a couple of seconds later and obviously, the flashing fails.
Can you help me find my smile?
Click to expand...
Click to collapse
It's behind the cupboard on the second floor, you left it there last week
But on a more serious note, have you tried doing a repair using either SEUS or PC Companion? It flashes your phone all the way back to original firmware, but that's always better than nothing
Yes, i've since repaired the firmware and the problem persists.
If you start it up, does the led flash red?
Nothing from the LED. Only time I can see the LED is when it's on charge.
uhmmm... i guess Sony-Ericsson repair center would be an option at this point, wouldn't know what it could be.
Was this just random? Or any damange happend?.. Looks like some harware issue.. If u can find some video's on youtube make for disassmely n check if internal the connection are connected properly. Specially the flex which connects to the motherboard.
Sent from my U20i using xda premium
Yes, disassembled and reassembled the phone and checked all the internal connections, and everything seems fine as far as I can tell - I disconnected and then reconnected all the connections anyway just in case, and the problem persists.
Problem just started one day, but I was drunk at the time (surprise surprise) so it's not inconceivable that it MAY have taken some damage, but I'm very much certain it did not.
Ok can u tel which ROM n kernel u are on?? N after connecting ur phone into flash mode ( as u said in the main thread ) it disconnects, can u tell which error it reports from its log..
Sent from my U20i using xda premium
No idea which rom and kernel - what's on it currently will be the latest firmware that PC companion repairs with.
I can't tell which error it is, it just says "error: flashing aborted" in flashtool.
sodslaw said:
No idea which rom and kernel - what's on it currently will be the latest firmware that PC companion repairs with.
I can't tell which error it is, it just says "error: flashing aborted" in flashtool.
Click to expand...
Click to collapse
Once, I got the same problem as you... I solved it via SEUS... Seeing you said 'PC Companion', I suugest you to use SEUS (Sony Ericsson Update Service). Those are two different programs..
Hopefully, it helps..
And, by the way, what happened when you open flashtool, and connect your phone in flash mode ? Does it keep getting errors, or just when you tried to flash some kernel ?
Sent from my U20i using XDA
Here's the situation:
My sister did something bad about her phone(x10 mini pro).
It has a newly installed stock rom (the phone used to have cyanogen but she told me to revert it back to stock).
She told me that all she did was install SonyEricsson Xperia Flasher on her machine and used it to flash her x10 mini pro. The flasher tells her that it is succesfull but when she turned off her phone for a restart, the phone does not turn on anymore. I have tried charging the battery overnight as well as using a different working battery but it does not help. Pressing the power button does nothing. No led light, no vibration, nothing. I have also tried different button combo(tried almost any combination) found here in forums but it does nothing as well.
I bought this device to a tech guy which is in a mall and he is charging me Is there something else I can do to fix thing device without spending? Is there another way other than unbrickin it with JTAG?
Any help or suggestion would be greatly appreciated.
Edit:
SEUS does not help because the phone cannot be detected when plugged in because it doesnt turn on and yes, I tried using a different usb cable.
I think my sister flashed the wrong kernel.
Does the battery charge (green LED)?
Do you know someone with the same phone? Try his/her battery. I had this problem too once, it would not turn on or anything, untill i tried to insert another battery. Then it started up and all. After clear battery stats, it worked again with my own battery.
This gives me the assumption, that is has something to do with battery stat (doh') - therefore all guides about doing a SEUS or other stock flash, should also instruct users to do a clear battery stat before the stock-flash.
Any one correct me on this if i'm totally wrong
gonix said:
Here's the situation:
My sister did something bad about her phone(x10 mini pro).
It has a newly installed stock rom (the phone used to have cyanogen but she told me to revert it back to stock).
She told me that all she did was install SonyEricsson Xperia Flasher on her machine and used it to flash her x10 mini pro. The flasher tells her that it is succesfull but when she turned off her phone for a restart, the phone does not turn on anymore. I have tried charging the battery overnight as well as using a different working battery but it does not help. Pressing the power button does nothing. No led light, no vibration, nothing. I have also tried different button combo(tried almost any combination) found here in forums but it does nothing as well.
I bought this device to a tech guy which is in a mall and he is charging me Is there something else I can do to fix thing device without spending? Is there another way other than unbrickin it with JTAG?
Any help or suggestion would be greatly appreciated.
Edit:
SEUS does not help because the phone cannot be detected when plugged in because it doesnt turn on and yes, I tried using a different usb cable.
I think my sister flashed the wrong kernel.
Click to expand...
Click to collapse
The Experia Flasher is not for the 2010 devices i think, so she may well have flashed the wrong firmware. SUS doesn't need to detect the phone, if you choose update and it can't recognise the phone it offers a repair option, this lets you choose the model yourself, it will download the proper firmware and all you have to do is connect your phone in flash-mode (ie hold the back-button while you plug in the usb-cable).
But she may well have bricked it properly and in that case, JTagging it is the only option to get it back up and working.
Screen-shots are from the old PC Companion, byt they still looks very much like them in the new version
http://forum.xda-developers.com/showpost.php?p=17458289&postcount=8
Emperor.dk said:
Does the battery charge (green LED)?
Do you know someone with the same phone? Try his/her battery. I had this problem too once, it would not turn on or anything, untill i tried to insert another battery. Then it started up and all. After clear battery stats, it worked again with my own battery.
This gives me the assumption, that is has something to do with battery stat (doh') - therefore all guides about doing a SEUS or other stock flash, should also instruct users to do a clear battery stat before the stock-flash.
Any one correct me on this if i'm totally wrong
Click to expand...
Click to collapse
Oh I know someone who has the same x10 with me. I guess Ill have to try your suggestion.
SmG67 said:
The Experia Flasher is not for the 2010 devices i think, so she may well have flashed the wrong firmware. SUS doesn't need to detect the phone, if you choose update and it can't recognise the phone it offers a repair option, this lets you choose the model yourself, it will download the proper firmware and all you have to do is connect your phone in flash-mode (ie hold the back-button while you plug in the usb-cable).
But she may well have bricked it properly and in that case, JTagging it is the only option to get it back up and working.
Click to expand...
Click to collapse
It doesnt help because when Im in the part where it says, press the back button while inserting the usb, the phone cannot be detected and so the update cannot continue.