[Q] No Found RKAndroid rock usb - Android Q&A, Help & Troubleshooting

I'm trying to flash my Pipo S3, but when I plug it, RKAndroidTool returns "No Found RKAndroid rock usb". I have installed the drivers.
I'm using Windows 7 x64.
Thanks.
edit. I wasn't into flash mode, I was into recovery mode.
To get into flash mode with Pipo S3:
1) Start holding Volume +
2) Insert USB
3) Start holding Power
You will hear a notification sound from windows, install drivers if needed and you will be able to flash.
The screen will remain black.

Related

[Q] XT910 (4.0.4) Wont connect to PC

Hi everyone.
So I have a Motorola Droid RAZR XT910 its on 4.0.4 OTA with no root.
The issue I have is that I connect the phone to my PC via USB cable and it does not pick it up.
A few things you must know is:
•I have windows 7 32-bit and
•I am using the cable that comes with my phone
What happens when I plug my phone is the computer says installing drivers for unknown device and then it claims to have successfully installing them for "unknown device". My phone does give me option to chose what type of connection I want but it does charge.
Things I have tried:
•A different cable
•A different PC
• Re-installing drivers
• Re-installing Motocast
•Trying with USB Debugging enabled and disabled
•Different USB ports
•Factory reset
•Different USB ports
•Tried installing PIM Sync form Google Play Store
So yeah that's my problem any help will be helpful...
Try the drivers here:
http://www.motorola.com/consumers/v...59431210VgnVCM1000008406b00aRCRD&pubid=987654
When you try another cable, make sure that works with another device, and not just for charging.
The below instructions will help you troubleshoot if there is a problem with the usb connector on your phone.
1.Power off and disconnect usb cable.
2.Press and hold vol up and down, then hold the power button.
3.You should come to a boot mode selection menu.
4.Press vol down twice to highlight AP fastboot, press vol up once to select.
5.You should see AP fastboot flash mode (s), with last 2 lines saying "Connect USB, Data Cable"
6.Connect your USB cable to your PC and phone, and see if it says USB connected.
7. If nothing happens then it's probably a hardware problem, get it repaired.
Nikorasu said:
Try the drivers here:
http://www.motorola.com/consumers/v...59431210VgnVCM1000008406b00aRCRD&pubid=987654
When you try another cable, make sure that works with another device, and not just for charging.
The below instructions will help you troubleshoot if there is a problem with the usb connector on your phone.
1.Power off and disconnect usb cable.
2.Press and hold vol up and down, then hold the power button.
3.You should come to a boot mode selection menu.
4.Press vol down twice to highlight AP fastboot, press vol up once to select.
5.You should see AP fastboot flash mode (s), with last 2 lines saying "Connect USB, Data Cable"
6.Connect your USB cable to your PC and phone, and see if it says USB connected.
7. If nothing happens then it's probably a hardware problem, get it repaired.
Click to expand...
Click to collapse
Hi thank you for your help.
So I did this method on my PC and it was unsuccessful but i tried it on my mothers and it worked!
So I will update the drivers on my mothers PC and see If I can successfully connect to her PC and use USB mass storage for the first time since I've had Ice Cream Sandwich!
I will keep you updated
Its definitely software. Ill have to wait till there's a rooting application that doesn't require a connection between a PC and phone. One rooted I can flash a ROM from there on...
On your mother's PC, it worked in AP fastboot right? As in the words "USB connected" appears on your phone.
From there you can flash a rom.
Nikorasu said:
On your mother's PC, it worked in AP fastboot right? As in the words "USB connected" appears on your phone.
From there you can flash a rom.
Click to expand...
Click to collapse
I can flash fastboot files which I dont want to do.. I want to flash custom ROMs which require root.
The ap fastboot worked for me but when i restarted the phone it still wont connect with mass storage. i do not own a motorola usb cable mine is an LG and i dont really have money to buy one. bought the phone on ebay and it did not ship with one so ive been using this. it only connects as charging.

[Q] Onda v701 not recognized by windows

After a did a firmware update using USB Burning tool, without no troubles, I want to install other firmware because the accelerometer doesn't work, and so the auto-rotate function (it worked on the old firmware), and I can't get into recovery mode, the home + power function does not work anymore.
I want to use USB Burning tool to reflash the tablet, like the last time, but now I have this problem: when I connect the tablet trough USB cable with the power on, windows recognize the mass storage, but when the power is off, which I need for USB Burning tool, it doesn't do anything. It should show in the bottom-right corner that USB device found, but it doesn't.
I tried this:
1. to hold home-button and then to insert USB... nothing, it just shows the battery charging
2. to hold home+power button... nothing... doesn't enter in recovery mode, it's just loading android system.
3. SD card slot was empty when I tried this.
Does anybody had some king of problems? or know what's the problem?
Please, I need to fix this.

[Q] Can't Fastboot

Hi,
I have on my tf201 latest official firmware, 4.1.1 build-number: JRO03C.WW_epad-10.4.2.18-20121122.
As Asus doesn't provide any more updates for our device and mine is out of warranty I'm finally ready to move on to some custom roms.
My tablet is Rooted.
Now after a lot of reading I thought it would be wise to do a backup of everything and make my device unbrickable.
I started to follow the instructions on this site : matthill.eu/android/transformer-prime-tf201-jellybean-nvflash
At first I backed everything up with Titanium Backup and then I did a factory reinstall, so I would have a clean tablet to start.
Then I installed the unlocking tool and succesfully unlocked my device.
I restarted my tf201 with holding the volume button down to get the options to enter fastboot.
When I got to the selection menu, I press the volume button a few times to select the USB-icon.
Then I press the volume up button to enter fastboot, but nothing happens. It just freeze.
The only thing I can do is hold the power button until my tablet restarts.
Also, since i'm on JB I never could connect it on my pc anymore. It even doesn't show up as an unknown device.
So when I want to use ADB I have to use ADB Konnect (wireless ADB).
JNiels1980 said:
Hi,
I have on my tf201 latest official firmware, 4.1.1 build-number: JRO03C.WW_epad-10.4.2.18-20121122.
As Asus doesn't provide any more updates for our device and mine is out of warranty I'm finally ready to move on to some custom roms.
My tablet is Rooted.
Now after a lot of reading I thought it would be wise to do a backup of everything and make my device unbrickable.
I started to follow the instructions on this site : matthill.eu/android/transformer-prime-tf201-jellybean-nvflash
At first I backed everything up with Titanium Backup and then I did a factory reinstall, so I would have a clean tablet to start.
Then I installed the unlocking tool and succesfully unlocked my device.
I restarted my tf201 with holding the volume button down to get the options to enter fastboot.
When I got to the selection menu, I press the volume button a few times to select the USB-icon.
Then I press the volume up button to enter fastboot, but nothing happens. It just freeze.
The only thing I can do is hold the power button until my tablet restarts.
Also, since i'm on JB I never could connect it on my pc anymore. It even doesn't show up as an unknown device.
So when I want to use ADB I have to use ADB Konnect (wireless ADB).
Click to expand...
Click to collapse
When you press up on the USB icon and it freezes that it normal.. This is fastboot mode.
You now must access it over a PC after installing the naked drivers.. If it is not showing on your PC then either try a different PC or your cable is faulty.
Thanks for the quick reply.
I tried once more to enter fastboot. Same result.
But when I disconnected my usb cable to connect it to an other computer, suddenly I got this message on my tablet:
"Starting Fastboot USB download protocol"
This message didn't show up before.
I plugged the tablet back to my pc, but still no device detection in device manager, even when refreshing (So I can't install naked drivers, as it is not recognized).
My computer is a Windows 8.1 system.
I restarted my tablet again, (after disconnecting it from my pc) and followed the procedure to enter Fastboot again.
I waited for the message "Starting Fastboot ..." and then I connected the cable to my other pc (Windows 7 system)
Same result as on the Windows 8.1 machine, not recognized
You say it could be that my cable is broken. Maybe, but it's a strange coincidence that this happened when switching from ICS to JB.
I know JB for the tf201 is been out a long time, and I updated since I could. So over time, maybe my cable could be broken now. But I'm sure I had this problem (not recognizing) since then, because right after updating I wanted to do some things with ADB and so I found out I had this problem.

[Q] LG Optimus L9 P760 dead?

Hi,
I have installed inappropriate version of CWM on my L9. Now it won't boot at all. When I press and hold power button to start the device, it stucks in a loop like this:
1. Short vibration.
2. LG logo screen appears for a second.
3. Black screen for another 3 seconds.
1. Vibration occurs again...
2. LG logo... etc
Situation above describes a behavior of the phone, which is disconnected from any wires.
Now when I plug shutted down device into USB port to Windows 7 PC, following mess happens:
1.Computer beeps like, USB device is connected.
2.Phone vibrates shortly.
3.Phone shows LG logo for a sec.
4.Phone shows black screen for 3 seconds.
5.Computer beeps like USB is disconnected.
... and again, and again.
Adb nor fastboot doesn't recognize any device (it did, before I have installed that wrong version of CWM, so USB drivers are OK I guess).
I tried hard reset, LG update tools, LGMobile support tool and of course I spent a whole day by searching this forum for any solution. I found similiar cases to mine (continuous beeps like Windows is detecting plugging and unplugging USB device), but this seems to be quite different because of continuous restarting of the phone, so the PC doesn't have a time to initiate USB device.
I would be really greatful for any help. Thanks
Edit: Problem SOLVED!
I solved it by following:
1. Download omap4boot from http://forum.xda-developers.com/showthread.php?t=1971014
2. Install driver for continuously plugging/unplugging phone in windows device manager (use omap4boot-for_optimus-v1.21\usb_drv_windows folder for search driver). Install it while the device is connected to PC.
3. Run command line and navigate to the omap4boot-for_optimus-v1.21 folder and run start_fastboot.bat.
4. Disconnect phone from PC.
5. Select 3. item Prada (works for L9 P760).
6. When prompted, connect turned off phone to the PC.
7. When promted to fastboot devices, choose Yes. Device should be found now. At this point you have approximately 3 minutes (device should stop restarting itself for a while) to do the rest.
8. Run another command line (do not close current one), navigate to android platform-tools and run fastboot flash recovery command with appropriate CWM img file. File can be downloaded here http://mobotalks.com/android/how-to-unlock-the-bootloader-and-install-cwm-recovery-on-lg-optimus-l9-ultimate-guide/
Done.

(Help) Asus ZenFone 5 bricked, stucks at Asus logo!

Hi everyone, i ask for your help cause i have a common problem but the fixes i found in the forum didn't work for me: my ZenFone 5 stucks at "Asus" logo with a "loading loop" wheel below that.
I know this post may be long but i beg you to read all steps:
1) Phone stucks at logo, but could enter recovery (pressing vol + down), i've updated it via external SD card (official firmware but didn't work) then i've wiped data and did a factory reset. Phone still stucks at logo.
2) Now i can't even enter recovery mode... when pressing vol + down it shows 2 options but whatever i choose the phone reboots. If i press vol + up it says "CSC mode, long press power to restart. Phone still stucks.
3) Now (after some time) the phone's screen doesn't show anything, nor charging icon or notification led when recharging, but strangely the computer recognizes it as a device when connected via USB cable, and the led turns on when i do this.
A friend told me to follow a guide that says to install "Intel Soc USB driver", i did that. After installing, when connecting the device, 2 things should pop up in Device Mangager under "Intel Soc": CloverviewPlus Device and Intel Soc USB Driver... but the second one doesn't show to me
I've also tried Asus flashtool guide... at step 4 it says to click in the box icon and choose the firmware RAW file, so i've downloaded a raw firmware for the ZenFone 5, but oddly it doesn't let me choose any raw file.
Note: the phone is recognized by the pc as "QHSUSB_BULK", so i've tried to update its driver with qualcomm drivers, and now it's recognized as "Qualcom MMC Usb storage device". But i think i've did a wrong thing cause my friend told me i should have choosed some kind of official driver
Thanks in advance for your help

Categories

Resources