Hello I inadvertently flashed his XT910 XML firmware 4.1.2 for XT912. The telephone does not work. I tried unbrick, but it does not work, does not start recovery. Runs only bootloader error "Invalid CG OTV".
Help restore the phone, please.
Thank you!
I am sorry for my bad English, I use Google Translate
UPD:
Through RSD Lite to flash now can only XT912 JB.
The phone turns on, but does not load launcher etc.
Other firmware via RSD not even installed. An error "failed flashing process 13/18 flash system".
I got that error too, try downloading the file again ut was a bad download or corrupted file...
Sent from my XT910 using xda premium
Steven87 said:
I got that error too, try downloading the file again ut was a bad download or corrupted file...
Sent from my XT910 using xda premium
Click to expand...
Click to collapse
Thanks for the reply! Unfortunately, this does not resolve the problem.
I think we should wait for the XML JB XT910.
I had the same problem, i switched from ICS to JB.vodafone and kept my root with Voodoo root keeper. One time my phone got into bootloop after restart (messed with build.prop a bit ).
Well i flashed a lot of stupid firmwares over RSD even x912 jellybean fastboot files on my x910 . But it just doesnt work
So a guy came to XDA forums and wrote this http://forum.xda-developers.com/showthread.php?t=2194825 I fallowed this instruction and got unbricked
I lost my Root, but i can atleast use my phone, which is more important :victory:
So there is one more side note to this tutorial
(as i flashed all sorts of files into my phone by trying to unbrick it, my partitions were a mess so)
So Before You use HDA-Pilot's instructions flash all partitions that you still have access to by hand.
Download EuroperRETAIL fastboot files that HDA gives you in his thread and flash with fastboot like this:
->fastboot flash recovery recovery.img
->fastboot flash cdrom cdrom_signed.img
...........
.....
...
Do this too all files and you will get error on system_signed and Boot.img, but your partitions will be ready to house euRetail JB and you will get System and Boot flashed on HSD-Pilot's tutorial, just before unbricking your doodles
TeddyOFLove said:
I had the same problem, i switched from ICS to JB.vodafone and kept my root with Voodoo root keeper. One time my phone got into bootloop after restart (messed with build.prop a bit ).
Well i flashed a lot of stupid firmwares over RSD even x912 jellybean fastboot files on my x910 . But it just doesnt work
So a guy came to XDA forums and wrote this http://forum.xda-developers.com/showthread.php?t=2194825 I fallowed this instruction and got unbricked
I lost my Root, but i can atleast use my phone, which is more important :victory:
So there is one more side note to this tutorial
(as i flashed all sorts of files into my phone by trying to unbrick it, my partitions were a mess so)
So Before You use HDA-Pilot's instructions flash all partitions that you still have access to by hand.
Download EuroperRETAIL fastboot files that HDA gives you in his thread and flash with fastboot like this:
->fastboot flash recovery recovery.img
->fastboot flash cdrom cdrom_signed.img
...........
.....
...
Do this too all files and you will get error on system_signed and Boot.img, but your partitions will be ready to house euRetail JB and you will get System and Boot flashed on HSD-Pilot's tutorial, just before unbricking your doodles
Click to expand...
Click to collapse
Thank you very much for your reply!
Unfortunately, nothing happened. Maybe we did something wrong, I do not know.
superdeman said:
Thank you very much for your reply!
Unfortunately, nothing happened. Maybe we did something wrong, I do not know.
Click to expand...
Click to collapse
What region are you from?
Is it XT910 you are using?
Did you try to fallow HSD guide and flash FF manually before hand? If so then what happened what is the issue after doing so|?
TeddyOFLove said:
What region are you from?
Is it XT910 you are using?
Did you try to fallow HSD guide and flash FF manually before hand? If so then what happened what is the issue after doing so|?
Click to expand...
Click to collapse
Device regoin EMEA. I'm from Belarus.
Yes, i use XT910.
Tried to do the instructions, but after that nothing changes. Loaded only bootloader with an error partition system.
If you is not difficult, please write how you restore your phone, step by step with links.
I would be very grateful!
superdeman said:
Device regoin EMEA. I'm from Belarus.
Yes, i use XT910.
Tried to do the instructions, but after that nothing changes. Loaded only bootloader with an error partition system.
If you is not difficult, please write how you restore your phone, step by step with links.
I would be very grateful!
Click to expand...
Click to collapse
I will try. But remember this is all HSD-Pilots work, i only try to make it clear to you.
1) download These fastboot files.rar (clink on text)
2)download retailEU. jellybean OTA
3)Download HSD-pilots UNBRICK.rar
4)UNRAR HSD-pilots UNBRICK.rar from step (3) to any new folder (lets name it UNBRICK)
5) UNRAR Fastboot files:
cdrom_signed
cdt.bin_signed
devtree_signed
ebr_signed
mbr_signed
recovery_signed
radio.img
system_signed
from step (1) to Folder from step (4) we named UNBRICK ONLY extract files i said
6)Connect your device to pc
7)open UNBRICK folder Hold shift and right click on white space -> then press OPEN COMMAND WINDOW HERE
8)flash files from step (5) by writing in the command window you opened:
mfastboot flash cdrom cdrom_signed
mfastboot flash cdt.bin cdt.bin_signed
mfastboot flash devtree devtree_signed
mfastboot flash ebr ebr_signed
mfastboot flash mbr mbr_signed
mfastboot flash recovery recovery_signed
mfastboot flash radio radio.img
9)with the phone still connected to PC open UNBRICK folder and tun Unbrick.bat.
10) after unbrick.rar flashed press power button once, and immediately hold volume up + volume down and press power again
11) go down to recovery and press volume up
12) when you just follow instructions in bat file. see android picture press volume down and volume up at the same time and wait for radio to install
13) after installation of radio wipe data and catch -> navigate to factory reset and do it
14) Then go to install update from external memory and install retailEU. jellybean OTA that you downloaded (you have to put it to your external SD card)
15) If all is fine it will update, just reboot and its unbricked
TeddyOFLove said:
I will try. But remember this is all HSD-Pilots work, i only try to make it clear to you.
1) download These fastboot files.rar (clink on text)
2)download retailEU. jellybean OTA
3)Download HSD-pilots UNBRICK.rar
4)UNRAR HSD-pilots UNBRICK.rar from step (3) to any new folder (lets name it UNBRICK)
5) UNRAR Fastboot files:
cdrom_signed
cdt.bin_signed
devtree_signed
ebr_signed
mbr_signed
recovery_signed
radio.img
system_signed
from step (1) to Folder from step (4) we named UNBRICK ONLY extract files i said
6)Connect your device to pc
7)open UNBRICK folder Hold shift and right click on white space -> then press OPEN COMMAND WINDOW HERE
8)flash files from step (5) by writing in the command window you opened:
mfastboot flash cdrom cdrom_signed
mfastboot flash cdt.bin cdt.bin_signed
mfastboot flash devtree devtree_signed
mfastboot flash ebr ebr_signed
mfastboot flash mbr mbr_signed
mfastboot flash recovery recovery_signed
mfastboot flash radio radio.img
9)with the phone still connected to PC open UNBRICK folder and tun Unbrick.bat.
10) after unbrick.rar flashed press power button once, and immediately hold volume up + volume down and press power again
11) go down to recovery and press volume up
12) when you just follow instructions in bat file. see android picture press volume down and volume up at the same time and wait for radio to install
13) after installation of radio wipe data and catch -> navigate to factory reset and do it
14) Then go to install update from external memory and install retailEU. jellybean OTA that you downloaded (you have to put it to your external SD card)
15) If all is fine it will update, just reboot and its unbricked
Click to expand...
Click to collapse
Thank you! Excellent manual! It's simple and clear.
But, unfortunately:
Code:
mfastboot flash cdt.bin cdt.bin_signed
sending 'cdt.bin' (16 KB)... OKAY [ 0.000s]
writing 'cdt.bin'... INFOPreflash validation failure
FAILED (remote: )
superdeman said:
Thank you! Excellent manual! It's simple and clear.
But, unfortunately:
Code:
mfastboot flash cdt.bin cdt.bin_signed
sending 'cdt.bin' (16 KB)... OKAY [ 0.000s]
writing 'cdt.bin'... INFOPreflash validation failure
FAILED (remote: )
Click to expand...
Click to collapse
Just ignore it
it doesnt matter as long as you fallow all at steps. the end should be unbricked, and it was bad tutorial just didnt have much time to make it easier to read.
i think cdt.bin was supposed to fail others will not, i just didnt remember the details as i did it week ago
So as i said just do it from start and copy all errors you get, as it may just be something i overlooked and it will still unbrick your phone hopefully, other wise we get more data on what might be wrong. Actually if you would agree on live session on team-viewer so i can control your pc and do it for you it would be ok too .
hi, i have an european gsm xt910 with deleted CID and verizion us jb (http://forum.xda-developers.com/showthread.php?t=2182674).
i've been using it for a couple of weeks with no problem, but today, after i turned off the phone, each time i try to turn it on it appears a black screen with the following white things (like the fastboot mode):
AP Fastboot Flash Mode (S) (Boot Failure)
0A.6c
To return to normal mode - first press power key to power down
Device is LOCKED. Status code: 0
Battery OK
OKto Program
Connect USB
Data Cable
Invalid CG OTV (CG: webtop): Invalid SP Data
Invalid CG HAV (CG: wbtop, status: 0X004E)
Invalid CG OTV (CG: webtop)
Click to expand...
Click to collapse
is it bricked? do i have to follow HDA-Pilot's instructions or is it something different since i deleted my CID (although i have a backup, i can't recover it because i can't boot into recovery)?
if there's another way to recover my phone with keeping root would be great, but of course it's better to have a working phone without root than a rooted brick
this evening i'm leaving for the whole weekend, so it would be awesome if you could answer me asap, so i can (hopefully!) fix my phone before departing. TY!
AW: Bricked XT910
http://forum.xda-developers.com/showthread.php?p=38189529
Gesendet von meinem XT890 mit Tapatalk 2
HSD-Pilot said:
http://forum.xda-developers.com/showthread.php?p=38189529
Gesendet von meinem XT890 mit Tapatalk 2
Click to expand...
Click to collapse
thanks a lot man!! i solved it by simply running the whirleyes's razr_bl_mbm_*.zip you linked me to.
Me too! jeje
ok, i got a new message similar to the previous one. this is the situation:
i have an italian gsm xt910 with deleted CID and verizion us jb (http://forum.xda-developers.com/show....php?t=2182674) and i tried to install the CM10.1 xt910 version. i use BMM.
- during boot i went to BMM and restored CID
- wiped everything
- installed the lastest CM10.1 nightly (0430) + gapps
and after i booted the phone it appeared the following message:
AP Fastboot Flash Mode (S) (Boot Failure)
0A.77
eMMC Info: Size 16G
To return to normal mode - first press power key to power down
Device is LOCKED. Status code: 0
Battery OK
OKto Program
Connect USB
Data Cable
Invalid CG HAB (CG: boot, status: 0X0056)
Click to expand...
Click to collapse
and i can't go to recovery anymore, since this message appears ASAP the phone starts. what happened? how can i fix this? ty in advance.
i found this thread (http://forum.xda-developers.com/showthread.php?t=2194825), but i'd rather not lose root + recover it using linux (never used linux), if it is possibile. is it enought to go here and install the retail UK firmware using RSD lite?
edit: ok i used rsd lite 6.15 + the UK JB firmware. now i'm fighting (using this thread) to gain my root rights back
Related
How to fix this problem ?
AP Fastboot Flash Mode (S) (Boot Failure)
Battery OK
Invalid CG OTV (CG: system): Invalid SP Data
Invalid CG HAB (CG: system, status: 0X0035)
Invalid CG OTV (CG: system)
You have problem with the recovery , so i think you need a Stock Recovery, request from ( kholk ) .
in FASTBOOT
fastboot flash recovery recovery.img
where i can download recovery.img file?
I have make dd /dev/block/mmcblk1p15 which is belong to recovery partition (stock recovery).
See if this could help.
http://www.mediafire.com/?ccmap2alh8355wc
p/s: I'm not responsible if you hardbrick the phone.
polaris441 said:
I have make dd /dev/block/mmcblk1p15 which is belong to recovery partition (stock recovery).
See if this could help.
http://www.mediafire.com/?ccmap2alh8355wc
p/s: I'm not responsible if you hardbrick the phone.
Click to expand...
Click to collapse
You have made on dorid razr not razr european version (910). Can you make boot.img also or explain the way?
acer73 said:
You have made on dorid razr not razr european version (910). Can you make boot.img also or explain the way?
Click to expand...
Click to collapse
You can backup the partition on your phone using dd command in terminal.
You can check the block partition using root explorer, then go to /dev/block where you can see the symlink of the partition blocks.
This is on my phone (SEA version):
mmcblk1p14 boot
mmcblk1p21 cache
mmcblk1p16 cdrom
mmcblk1p18 cid
mmcblk1p25 emstorage
mmcblk1p19 kpanic
mmcblk1p17 misc
mmcblk1p7 pds
mmcblk1p22 preinstall
mmcblk1p15 recovery
mmcblk1p20 system
mmcblk1p24 userdata
mmcblk1p8 utags
mmcblk1p23 webtop
command on terminal (e.g. to backup system partition):
dd if=/dev/block/mmcblk1p20 of=/mnt/sdcard/system.img
replace sdcard to sdcard-ext if the image to be copied on external sdcard
PLZ Give me this files:
boot
cache
cid
pds
recovery
webtop
thanks polaris 441. FR version have same block partition. So if my phone have a problem with boot just becouse in every start i see ap fastboot failure i can use a boot.img from another Fr phone?
acer73 said:
thanks polaris 441. FR version have same block partition. So if my phone have a problem with boot just becouse in every start i see ap fastboot failure i can use a boot.img from another Fr phone?
Click to expand...
Click to collapse
Yes you can .
medo18 said:
Yes you can .
Click to expand...
Click to collapse
medo18 for AP Fastboot Flash Mode (S) (Boot Failure) i flash with fastboot only boot.img to recovery the error. peraphs i can't flash with closed bootloader?
Just take note that fastboot has certain limitation on the file size it can handle. During my atrix days, I use moto-fastboot to flash big img file like system and webtop.
polaris441 said:
Just take note that fastboot has certain limitation on the file size it can handle. During my atrix days, I use moto-fastboot to flash big img file like system and webtop.
Click to expand...
Click to collapse
so the question is different. Can i flash boot.img or system.img on unlocked bootloder? MOTO-FASTBOOT IS COMPATIBLE ON RAZR? thanks for answers
acer73 said:
so the question is different. Can i flash boot.img or system.img on unlocked bootloder? MOTO-FASTBOOT IS COMPATIBLE ON RAZR? thanks for answers
Click to expand...
Click to collapse
I don't know and I do not dare to try yet as no sbf/fxz available as backup.
If my phone already softbrick like OP, maybe I will try.
The OP needs a system.img, not a recovery.img as started by the error displayed.
It seems that on RAZR Motorola wanted to prevent self repairs: on ATRIX for example the dd solution worked, here it seems that dd isn't able to copy the entire partition with its signature (consequently fastboot fails to flash due to missing signature).
At least from what I've read on my recovery thread. I've never personally tried to flash the image as my device is still alive....luckily.
Yes he need that and maybe PDSFIX.IMG like my Atrix 4g, the problem here is with the partition.
med18 and kholk,
plz help me because my battery is low and i cant do anything by fastboot, i cant charge battery.
WHT CAN I DO PLZ ?!
I think you have a tow choice :
1- Replace the battery with anyone.
2- Use FACTORY CABLE but i think is very risk, here
http://forum.xda-developers.com/showthread.php?t=1081743
medo18 said:
I think you have a tow choice :
1- Replace the battery with anyone.
2- Use FACTORY CABLE but i think is very risk, here
http://forum.xda-developers.com/showthread.php?t=1081743
Click to expand...
Click to collapse
Replace the battery is out of choice.
Sent from my XT910 using XDA App
acer73 said:
medo18 for AP Fastboot Flash Mode (S) (Boot Failure) i flash with fastboot only boot.img to recovery the error. peraphs i can't flash with closed bootloader?
Click to expand...
Click to collapse
your device is EU?
Yes, euro in particular FR
Inviato dal mio XT910 usando Tapatalk
After a failed update, no programs recognize my RAZR, and I could not make it work, until I decided to read the file. XML ROM folder that was downloaded.
I tried using RSD Lite but without success, always gave errors 1/20, 13/20.
I tried one last action: executed line by line what was done by the XML file I downloaded from the SBF http://forum.xda-developers.com/showthread.php?t=1362956 topic.
I created a. Bat file with the contents
Code:
moto-fastboot flash mbm allow-mbmloader-flashing-mbm.bin
moto-fastboot reboot-bootloader
moto-fastboot flash mbmloader mbmloader.bin
moto-fastboot flash mbm mbm.bin
moto-fastboot reboot-bootloader
moto-fastboot flash cdt.bin cdt.bin_signed
moto-fastboot reboot-bootloader
moto-fastboot erase cache
moto-fastboot erase userdata
moto-fastboot flash logo.bin logo.bin
moto-fastboot flash ebr ebr_signed
moto-fastboot flash mbr mbr_signed
moto-fastboot flash devtree devtree_signed
moto-fastboot flash system system_signed
moto-fastboot flash radio radio.img
moto-fastboot flash boot boot_signed
moto-fastboot flash recovery recovery_signed"
moto-fastboot flash cdrom cdrom_signed"
moto-fastboot flash preinstall preinstall"
moto-fastboot flash webtop webtop_signed"
moto-fastboot
I put the folder where you extracted the file "Branding: en.BR VIVO," along with the files from ADB + moto.fastboot.exe, and run the .BAT after connecting the phone in fastboot mode.
Okay, my phone went back to the LIVE STOCK ROM
sry for my bad english, i use translator in some parts
So this gets you back to dead stock vivo? Couldn't you just use fastboot?
Sent from my miui xt910
xxBrun0xx said:
So this gets you back to dead stock vivo? Couldn't you just use fastboot?
Sent from my miui xt910
Click to expand...
Click to collapse
His RSD lite in AP fastboot got damaged. There's a similar script by kholk as an alternative to moto flashing tool.
Thanks
Sent from my XT910 using Tapatalk 2
magraun said:
After a failed update, no programs recognize my RAZR, and I could not make it work, until I decided to read the file. XML ROM folder that was downloaded.
I tried using RSD Lite but without success, always gave errors 1/20, 13/20.
I tried one last action: executed line by line what was done by the XML file I downloaded from the SBF http://forum.xda-developers.com/showthread.php?t=1362956 topic.
I created a. Bat file with the contents
I put the folder where you extracted the file "Branding: en.BR VIVO," along with the files from ADB + moto.fastboot.exe, and run the .BAT after connecting the phone in fastboot mode.
Okay, my phone went back to the LIVE STOCK ROM
Click to expand...
Click to collapse
Hi
I have same problem.....RSD Always error 3/21....
i want flash "SPDIRD-40_MEA_RT_1C.91P_CFC_P2B_Signed.xml.zip"
Can you share me .Bat File.....
Thanks
Ok
finally find moto-fastboot...and flash frimware with fastboot command
but Always error on writing "mbmloader".........who know,why?
I have very big problem, delete every data on internal mass memory after rebooting phone.....also remove any installed app's after reboot phone
or remove old app's from phone,but old app's back to phone after reboot
so,i can't change anything..like data,app's.etc....Also i can't change firmware version after flashing new firmware
EX: my phone have a 2.3.5 (65.1.12.XT910.MERetail.en.06------Build 6.5.1_73-spd-ird-12) BUT After flash with 2.3.6 (6.5.1-167-SPD-IRD-40) I HAVE STILL OLD FIRMWARE
Please help me...mu phone is dead
BABAK236 said:
Ok
finally find moto-fastboot...and flash frimware with fastboot command
but Always error on writing "mbmloader".........who know,why?
I have very big problem, delete every data on internal mass memory after rebooting phone.....also remove any installed app's after reboot phone
or remove old app's from phone,but old app's back to phone after reboot
so,i can't change anything..like data,app's.etc....Also i can't change firmware version after flashing new firmware
EX: my phone have a 2.3.5 (65.1.12.XT910.MERetail.en.06------Build 6.5.1_73-spd-ird-12) BUT After flash with 2.3.6 (6.5.1-167-SPD-IRD-40) I HAVE STILL OLD FIRMWARE
Please help me...mu phone is dead
Click to expand...
Click to collapse
Try to read this if RSD doesnt work:
http://forum.xda-developers.com/showthread.php?t=1453660
elias.parasini said:
Try to read this if RSD doesnt work:
http://forum.xda-developers.com/showthread.php?t=1453660
Click to expand...
Click to collapse
Hi
Of Course Try this,but not solve my problem
i did try with fastboot command,,,all file's writed but always error when run this:
moto-fastboot flash mbmloader mbmloader.bin
Code:
sending 'mbmloader' (42 KB)... OKAY [ 0.016s]
writing 'mbmloader'... INFOCommand restricted
FAILED (remote: )
BABAK236 said:
Ok
finally find moto-fastboot...and flash frimware with fastboot command
but Always error on writing "mbmloader".........who know,why?
I have very big problem, delete every data on internal mass memory after rebooting phone.....also remove any installed app's after reboot phone
or remove old app's from phone,but old app's back to phone after reboot
so,i can't change anything..like data,app's.etc....Also i can't change firmware version after flashing new firmware
EX: my phone have a 2.3.5 (65.1.12.XT910.MERetail.en.06------Build 6.5.1_73-spd-ird-12) BUT After flash with 2.3.6 (6.5.1-167-SPD-IRD-40) I HAVE STILL OLD FIRMWARE
Please help me...mu phone is dead
Click to expand...
Click to collapse
I have the same EXACT problem! It is strange when I delete apps and wipe data, but after reboot it comes back. Have you had any luck on resolving this???
BABAK236 said:
Hi
Of Course Try this,but not solve my problem
i did try with fastboot command,,,all file's writed but always error when run this:
moto-fastboot flash mbmloader mbmloader.bin
Code:
sending 'mbmloader' (42 KB)... OKAY [ 0.016s]
writing 'mbmloader'... INFOCommand restricted
FAILED (remote: )
Click to expand...
Click to collapse
sory for delay
check this line: moto-fastboot flash mbm allow-mbmloader-flashing-mbm.bin.
your file probably have another name, like "allow_mbmloader_flashing_mbm.bin"
Hello guys,
Let me preface this with the fact that I have been searching this forum for the past hour and could not find anything pertinent for my situation.
I've updated to the latest GSM OTA (the Vodafone EU one) and all was great, decided to reboot my phone and got into a bootloop. I don't have a recovery to boot from and going to be short on battery soon.
The way I see it, I'm stuck with a bricked phone until the RSD package for the OTA is released. Is that correct? am I missing anything?
Can anyone point me to a relevant thread where I can catch a break?
Cheers!
tuxcomputing said:
Hello guys,
Let me preface this with the fact that I have been searching this forum for the past hour and could not find anything pertinent for my situation.
I've updated to the latest GSM OTA (the Vodafone EU one) and all was great, decided to reboot my phone and got into a bootloop. I don't have a recovery to boot from and going to be short on battery soon.
The way I see it, I'm stuck with a bricked phone until the RSD package for the OTA is released. Is that correct? am I missing anything?
Can anyone point me to a relevant thread where I can catch a break?
Cheers!
Click to expand...
Click to collapse
Fixed, please close.
How did you fixed it?
Sent from my XT910 using xda premium
Please tell us how you fixed this, i have same problem but i already screwed it up more by trying to flash back to ics after i was stuck at boot on JB vodafone. Now i have bricked phone and i wait for Fastboot files, which we dont know when will come out
Got the same problem here
Alright, here goes.
I am not responsible to whatever happens to your phones. This process is described for the Vodafone OTA.
Also, you will lose root
I'm guessing your phones are in a constant bootloop right about now. If they are, you have to make sure you still have some battery left so that on AP Fastboot it shows battery OK. If you don't, follow the guides here to get more juice or get a 'factory cable' and charge your phone.
To download:
- Fastboot from here: http://dfiles.eu/files/bih3tmg7b
- OTA kernel (here: http://d-h.st/xat )
- The whole OTA here ON YOUR SDCARD
- original ICS RSD Image here
Process:
Extract the fastboot somewhere accessible like c:/fastboot
Extract the kernel and the original ICS files on your desktop
Copy the OTA kernel (boot_3.0.8-g7198280) to your c:/fastboot folder
Copy 'system_signed' from the original ICS archive to your fastboot folder
Open the command prompt (search for cmd.exe in your programs)
Navigate to c:/fastboot (use "cd .." to excape a folder and "dir" to list the files in a folder )
Go to AP fastboot on your phpne and do the following from the command prompt:
fastboot flash boot boot_3.0.8-g7198280.img
fastboot flash system system_signed
fastboot reboot-bootloader
Now restart your phone and enter recovery the normal way volUp+volDown + power button then select Recovery, then volUp+volDown to see the menu.
Do a factory reset
Flash the OTA (that should be on your card)
Reboot
Ta-da!
If after the whole process you get a flash failure when rebooting your phone, use this guide to get rid of that: http://forum.xda-developers.com/showthread.php?t=1634223
If this helped you, please show the 'Thanks' button some love. Also, post here if you run into trouble, DO NOT PM!
tuxcomputing said:
Alright, here goes.
I am not responsible to whatever happens to your phones. This process is described for the Vodafone OTA.
Also, you will lose root
I'm guessing your phones are in a constant bootloop right about now. If they are, you have to make sure you still have some battery left so that on AP Fastboot it shows battery OK. If you don't, follow the guides here to get more juice or get a 'factory cable' and charge your phone.
To download:
- Fastboot from here: http://dfiles.eu/files/bih3tmg7b
- OTA kernel (here: http://d-h.st/xat )
- The whole OTA here ON YOUR SDCARD
- original ICS RSD Image here
Process:
Extract the fastboot somewhere accessible like c:/fastboot
Extract the kernel and the original ICS files on your desktop
Copy the OTA kernel (boot_3.0.8-g7198280) to your c:/fastboot folder
Copy 'system_signed' from the original ICS archive to your fastboot folder
Open the command prompt (search for cmd.exe in your programs)
Navigate to c:/fastboot (use "cd .." to excape a folder and "dir" to list the files in a folder )
Go to AP fastboot on your phpne and do the following from the command prompt:
fastboot flash boot boot_3.0.8-g7198280.img
fastboot flash system system_signed
fastboot reboot-bootloader
Now restart your phone and enter recovery the normal way volUp+volDown + power button then select Recovery, then volUp+volDown to see the menu.
Do a factory reset
Flash the OTA (that should be on your card)
Reboot
Ta-da!
If after the whole process you get a flash failure when rebooting your phone, use this guide to get rid of that: http://forum.xda-developers.com/showthread.php?t=1634223
If this helped you, please show the 'Thanks' button some love. Also, post here if you run into trouble, DO NOT PM!
Click to expand...
Click to collapse
I tried your method but I get a:
Preflash validating failure
when writing the system_signed to the device
pirondello said:
I tried your method but I get a:
Preflash validating failure
when writing the system_signed to the device
Click to expand...
Click to collapse
That's weird. Prolly the flash was messed up somewhere..
Try this before "fastboot flash boot boot_3.0.8-g7198280.img":
extract recovery_signed and allow-mbmloader-flashing-mbm.bin from the ICS folder and put them into the fastboot folder
do this
fastboot flash mbm allow-mbmloader-flashing-mbm.bin
fastboot reboot-bootloader
fastboot flash recovery recovery_signed
Let me know if that works
tuxcomputing said:
That's weird. Prolly the flash was messed up somewhere..
Try this before "fastboot flash boot boot_3.0.8-g7198280.img":
extract recovery_signed and allow-mbmloader-flashing-mbm.bin from the ICS folder and put them into the fastboot folder
do this
fastboot flash mbm allow-mbmloader-flashing-mbm.bin
fastboot reboot-bootloader
fastboot flash recovery recovery_signed
Let me know if that works
Click to expand...
Click to collapse
Unfortunately still the same problem, can't flash the system_signed file.
Really appreciate your help, thank you anyway!
tuxcomputing said:
That's weird. Prolly the flash was messed up somewhere..
Try this before "fastboot flash boot boot_3.0.8-g7198280.img":
extract recovery_signed and allow-mbmloader-flashing-mbm.bin from the ICS folder and put them into the fastboot folder
do this
fastboot flash mbm allow-mbmloader-flashing-mbm.bin
fastboot reboot-bootloader
fastboot flash recovery recovery_signed
Let me know if that works
Click to expand...
Click to collapse
Well i give you thumbs up and thanks for you helping hand, however it still doesnt work gives preflashvalidation failure on system_signed flashing. If you have some more ideas it would be really nicce to try, meanwhile i think we will just have to wait for fastboot files. Verizon version for xt912 got FF already maybe we will get ours in a week or so.
Use this method .. Hsd pilot again nailed it to save our asses ..
It should definatly unbrick your mobile because i tried it on same version and i am back on jellybean ..
http://forum.xda-developers.com/showthread.php?t=2194825
Hit the thx to hsd pilot on the op and me if ya think i helped ya to share link :thumbup:
Thx in advance btw
Sent from my Droid Razr HD (4GLTE) using Tapatalk 2
Edit: Always refresh before you reply
anurag.dj2u said:
Use this method .. Hsd pilot again nailed it to save our asses ..
It should definatly unbrick your mobile because i tried it on same version and i am back on jellybean ..
http://forum.xda-developers.com/showthread.php?t=2194825
Hit the thx to hsd pilot on the op and me if ya think i helped ya to share link :thumbup:
Thx in advance btw
Sent from my Droid Razr HD (4GLTE) using Tapatalk 2
Click to expand...
Click to collapse
Didn't work for me. Flashing went fine but when trying to enter recovery I get "Invalid Flash Mode (S) (Boot Failure)
HSD-Pilot said:
Edit: Always refresh before you reply
Click to expand...
Click to collapse
Sorry again :thumbdown:
Sent from my Droid Razr HD (4GLTE) using Tapatalk 2
No, you was first, i mean myself
HSD-Pilot said:
No, you was first, i mean myself
Click to expand...
Click to collapse
TeddyOFLove said:
Well i give you thumbs up and thanks for you helping hand, however it still doesnt work gives preflashvalidation failure on system_signed flashing. If you have some more ideas it would be really nicce to try, meanwhile i think we will just have to wait for fastboot files. Verizon version for xt912 got FF already maybe we will get ours in a week or so.
Click to expand...
Click to collapse
For your information, I managed to unbrick my phone. Problem seemed to be my CID.IMG. After erasing it, I could enter recovery and installl JB from ext-sdcard. Now I have to use BP Tools tools to boot, because as soon as I restore CID, the device doesn't boot.
Really strange, because my phone is actually from Europe (d/a/ch), Switzerland. Maybe it's due to the fact that I switched to the chinese JB Ota leak before updating to the EU leak.
Hello on the weekend that just passed my GSM RAZR's battery completely died and when I went to plug it in in the morning I was greeted with a black screen that reads:
AP Fastboot Flash Mode (S) (Boot Failure)
0A.6C
To return to normal mode - first press power key to power down
Device is LOCKED. Status Code: 0
Battery Low
Cannot Program
Connect USB
Data Cable
Invalid CG OTV (CG: webtop): Invalid SP Data
Invalid CG HAB (CG: webtop, status 0X004E)
Invalid CG OTV (CG: webtop)
I am on the cyanogenmod JB 4.2.2 and it was working fine without any issue really. I also don't think my phone is charging because it will only turn on if I plug it into and outlet. If I plug it in my computer to attempt to use RSD I just get the white light in the notification light.
So I was wondering if anyone could be of any help because this is my main phone and I am out of communication for the time being until it gets fixed.
EDIT: Forgot to mention that I can get into stock recovery by holding the volume +/- down and plugging it into a wall charger but any option I select brings me back to a similar screen, sometimes missing the errors the other screen had at the bottom.
Çözümü için herhangi bir XT910 yada XT912 (cihazına göre) Gingerbread temelli bir rom'un içerisinden webtop_signed.img dosyasını çıkarın ve aşağıdaki komutla flashlayın.
fastboot flash webtop webtop_signed.img
http://motomodtr.forumcommunity.net/?t=53855516
same issue
I have same problem. Please help. I don't know how to use command "fastboot flash webtop webtop_signed.img"... Where type this command?
I am on Jellybean 4.2.2, not Ginergread. Anyone else with any help? And I plugged the phone in all night last night and now it can show the menu without being on charge.
[/COLOR]
RideR10 said:
I have same problem. Please help. I don't know how to use command "fastboot flash webtop webtop_signed.img"... Where type this command?
Click to expand...
Click to collapse
flash it in using the fastboot folder, just search for the file. put the webtop file in the folder, open the command window on the folder and run the command
TheMrcool212 said:
[/COLOR]
flash it in using the fastboot folder, just search for the file. put the webtop file in the folder, open the command window on the folder and run the command
Click to expand...
Click to collapse
If it help I describe my RAZR...
I have made dual boot with boot menu manager on my razr: 1. system is stock JB 4.1.2
2.system is AOKP 4.2.2
Everything works fine until I changed bootanimation on 2. system. After reboot phone reports this issue
I download ICS 4.0.4 file, but this fastboot file doesn't contain file "webtop_signed". After that I download Gingerbread fastboot file, where I found file "webtop_signed". Will this gingerbread "webtop_signed" work with JB ?
Where can i download that "fastboot folder"?
In advance thank for your help and sorry for my ENG
http://dl.projectlense.com/download.php?file=spyder/razr_bl_mbm_0a77.zip
Download and extract this. Connect in AP and run the bat.
Gesendet von meinem XT890 mit Tapatalk 2
---------- Post added at 07:23 PM ---------- Previous post was at 07:13 PM ----------
BTW: Everyone that uses BMM and still got the 0A.6... Bootloader should update it by using the linked file, to prevent those Webtop Issues!
Gesendet von meinem XT890 mit Tapatalk 2
Thank you for your help. :good: I spent nearly two days searching for solution.
thanks alot
i had the same problem and almost threw it out the window
now fixed :good:
Help Please
Hey i have the same problem where it say " AP fastboot flash mode (S) (boot failure)" I ran the windows bat file and it restarted the bootloader but the same problem still showed. Anybody have any ideas as to what im doing wrong or what else i can do? thanks
HSD-Pilot said:
dl. projectlense. com/download.php?file=spyder/razr_bl_mbm_0a77.zip
Download and extract this. Connect in AP and run the bat.
Click to expand...
Click to collapse
Are you sure that download link not expired? The website is no more available. Any new link from anyone?
I have the same problem, after flashing Magisk 15.3 form RR Nougat OS.
What should I do?
I'v got Droid RAZER Utility 1.8 and tried to roll back to stock ICS via Fastboot but it didn't fix it, where is 'devtree' error in log.
My next attempt was to flash it with RDS Lite but it doen's work under Windows 10, to now I'm trying to manually flash firmware from RAZR XT910 Firmwares SuperThread (Jelly Bean) with Droid utility moto-fastboot.exe command.
For 9.8.2O-124_SPUEM-14_S7_USASPDRICS01RUKE1007.0R_USASPDRJBRTGB_P011_b57374ab5a_p2b_S1FF_fb_CFC.xml.zip firmware it will be:
Code:
moto-fastboot flash mbm allow-mbmloader-flashing-mbm.bin
moto-fastboot reboot-bootloader
moto-fastboot flash mbmloader mbmloader.bin
moto-fastboot flash mbm mbm.bin
moto-fastboot reboot-bootloader
moto-fastboot flash cdt.bin cdt.bin_signed
moto-fastboot erase cache
moto-fastboot erase userdata
moto-fastboot erase emstorage
moto-fastboot flash logo.bin logo.bin
moto-fastboot flash ebr ebr_signed
moto-fastboot flash mbr mbr_signed
moto-fastboot flash devtree devtree_signed
moto-fastboot flash system system_signed
moto-fastboot flash boot boot_signed
moto-fastboot flash recovery recovery_signed
moto-fastboot flash cdrom cdrom_signed
moto-fastboot flash emstorage emstorage.img
moto-fastboot flash radio radio.img
But I keep getting battery low warning:
Code:
moto-fastboot flash mbmloader mbmloader.bin
sending 'mbmloader' (42 KB)... FAILED (remote: Battery Low)
How to charge MOTO if I can't get to system and recovery, I'm not sure if it's charging on fastboot screen.
vkmaxx said:
My next attempt was to flash it with RDS Lite but it doen's work under Windows 10, to now I'm trying to manually flash firmware from RAZR XT910 Firmwares SuperThread (Jelly Bean) with Droid utility moto-fastboot.exe command.
For 9.8.2O-124_SPUEM-14_S7_USASPDRICS01RUKE1007.0R_USASPDRJBRTGB_P011_b57374ab5a_p2b_S1FF_fb_CFC.xml.zip firmware it will be:
But I keep getting battery low warning:
How to charge MOTO if I can't get to system and recovery, I'm not sure if it's charging on fastboot screen.
Click to expand...
Click to collapse
Buy or make the factory cable...
https://forum.xda-developers.com/showthread.php?t=1077414
I was able to flash my phone with moto-fastboot.exe by NOT executing "moto-fastboot reboot-bootloader". This was the moment when after reboot phone was showing "low battery" warrning. After taking it from charger and not rebooting I was able to flash it.
Then Jelly Bean -> root -> SafeStrap - > LineageOS
Hello,
After stuck flash to ICS, i decide to flash using JB files from sbf.droid-developers.org/umts_spuder/list.php
I used O2 JB and tried "Unknown Carrier" and "Retail British" also.
My XT910 get bit progress now. This device can turn on stable without any self reboot.
But again I can't boot to BP Tool
Now I only able boot to BP HW Diag.
Kindly help me to fix this issue.
idwijayaku said:
Hello,
After stuck flash to ICS, i decide to flash using JB files from sbf.droid-developers.org/umts_spuder/list.php
I used O2 JB and tried "Unknown Carrier" and "Retail British" also.
My XT910 get bit progress now. This device can turn on stable without any self reboot.
But again I can't boot to BP Tool
Now I only able boot to BP HW Diag.
Kindly help me to fix this issue.
Click to expand...
Click to collapse
Install the Boot Menu Manager in playstore. The recovery allows you to boot without BP Tools and BP HW Diag
TheMrcool212 said:
Install the Boot Menu Manager in playstore. The recovery allows you to boot without BP Tools and BP HW Diag
Click to expand...
Click to collapse
I have to root my device first.
But I'm not sure root for XT910 JB is available now.
anyone?
Turn off your phone, remove the sim card and reboot. Then, power off your phone again and insert sim card and reboot.
TheMrcool212 said:
Turn off your phone, remove the sim card and reboot. Then, power off your phone again and insert sim card and reboot.
Click to expand...
Click to collapse
OMG.... you saved my phone.. thanks a lot !!
It works, I can boot in BP Tools now..
Next step is how can I restore my cid and change my baseband without root?
Because upgrade to JB makes my baseband doesn't work in my region.
Also I found usb debugging notification on my phone, but it's not connected in pc.
idwijayaku said:
OMG.... you saved my phone.. thanks a lot !!
It works, I can boot in BP Tools now..
Next step is how can I restore my cid and change my baseband without root?
Because upgrade to JB makes my baseband doesn't work in my region.
Also I found usb debugging notification on my phone, but it's not connected in pc.
Click to expand...
Click to collapse
There are two methods to restore cid. One of the methods need root and other not needed. Since you have no root, download the file ( here ) in your PC. Then extract the file. make sure those files are in a folder. Put your cid.img file into the extracted file. Hold Shift + left click and select "open the command window here".
Turn off your phone. Go to the bootloader (like one you boot to bptools) but this time select the 'AP Fastboot mode' . Connect your phone to your PC. In the terminal, run this line:
Code:
fastboot flash cid cid.img
Make sure no errors when flashing it. And reboot
TheMrcool212 said:
There are two methods to restore cid. One of the methods need root and other not needed. Since you have no root, download the file ( here ) in your PC. Then extract the file. make sure those files are in a folder. Put your cid.img file into the extracted file. Hold Shift + left click and select "open the command window here".
Turn off your phone. Go to the bootloader (like one you boot to bptools) but this time select the 'AP Fastboot mode' . Connect your phone to your PC. In the terminal, run this line:
Code:
fastboot flash cid cid.img
Make sure no errors when flashing it. And reboot
Click to expand...
Click to collapse
Thank you for file
- so i download the file and use file for windows
- i start the command prompt and I got this error:
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
is there some steps that i missed?
and, after yesterday i sucessfully boot to BP Tool, today I can't boot on that mode again, although i did same like before
- power off phone in BP HW Diag
- take out the sim card
- boot again in BP HW Diag
- power off the phone again
- insert simcard
- boot in BP Tool
- now it's just stuck in O2 logo.
Please help me again
Never seen that problem before, but it worked for me. Try to follow these instructions.
1. Download the file ( Here! )
2. Extract the file. You will see a file named allow-mbmloader-flashing-mbm
3. Put the .bin file in the fastboot folder.
4. Put your phone in AP Fastboot mode, connect it to PC
5. Run these commands
Code:
fastboot flash mbm allow-mbmloader-flashing-mbm.bin
fastboot reboot-bootloader
fastboot flash cid cid.img
All thanks to the therazrguy
TheMrcool212 said:
Never seen that problem before, but it worked for me. Try to follow these instructions.
1. Download the file ( Here! )
2. Extract the file. You will see a file named allow-mbmloader-flashing-mbm
3. Put the .bin file in the fastboot folder.
4. Put your phone in AP Fastboot mode, connect it to PC
5. Run these commands
Code:
fastboot flash mbm allow-mbmloader-flashing-mbm.bin
fastboot reboot-bootloader
fastboot flash cid cid.img
All thanks to the therazrguy
Click to expand...
Click to collapse
Thank you again..
Those command line executed very well.
Suspend screen is not appear again.
But i got another error
Invalid CG OTV (CG: cdrom): Invalid SP Data
Invalid CG HAB (CG:cdrom, status: 0X0056)
Invalid CG OTV (CG: cdrom)
Please help me how to get my phone back..
idwijayaku said:
Thank you again..
Those command line executed very well.
Suspend screen is not appear again.
But i got another error
Invalid CG OTV (CG: cdrom): Invalid SP Data
Invalid CG HAB (CG:cdrom, status: 0X0056)
Invalid CG OTV (CG: cdrom)
Please help me how to get my phone back..
Click to expand...
Click to collapse
Try to flash the jelly bean fastboot file on RSD Lite. I think the European jelly bean fastboot files are out. But i am not sure.
Sent from my GT-I9300 using xda app-developers app
I flashed with O2 and Retail UK, but this error still exist.
I just erase cid using your command, so I can get back to BP HW Diag again, still can't boot to BP Tools.
idwijayaku said:
I flashed with O2 and Retail UK, but this error still exist.
I just erase cid using your command, so I can get back to BP HW Diag again, still can't boot to BP Tools.
Click to expand...
Click to collapse
You had just erased cid? did i just told you how to restore cid?
But anyway, after few minutes of searching, i have found someone posted how to flash the cdrom partition. It is by TeddyOFLove
I will try. But remember this is all HSD-Pilots work, i only try to make it clear to you.
1) download These fastboot files.rar (clink on text)
2)download retailEU. jellybean OTA
3)Download HSD-pilots UNBRICK.rar
4)UNRAR HSD-pilots UNBRICK.rar from step (3) to any new folder (lets name it UNBRICK)
5) UNRAR Fastboot files:
cdrom_signed
cdt.bin_signed
devtree_signed
ebr_signed
mbr_signed
recovery_signed
radio.img
system_signed
from step (1) to Folder from step (4) we named UNBRICK ONLY extract files i said
6)Connect your device to pc
7)open UNBRICK folder Hold shift and right click on white space -> then press OPEN COMMAND WINDOW HERE
8)flash files from step (5) by writing in the command window you opened:
mfastboot flash cdrom cdrom_signed
mfastboot flash devtree devtree_signed
mfastboot flash ebr ebr_signed
mfastboot flash mbr mbr_signed
mfastboot flash recovery recovery_signed
mfastboot flash radio radio.img
9)with the phone still connected to PC open UNBRICK folder and tun Unbrick.bat.
10) after unbrick.rar flashed press power button once, and immediately hold volume up + volume down and press power again
11) go down to recovery and press volume up
12) when you just follow instructions in bat file. see android picture press volume down and volume up at the same time and wait for radio to install
13) after installation of radio wipe data and catch -> navigate to factory reset and do it
14) Then go to install update from external memory and install retailEU. jellybean OTA that you downloaded (you have to put it to your external SD card)
15) If all is fine it will update, just reboot and its unbricked
Click to expand...
Click to collapse
Also, i forgot that HSD-Pilot posted a thread how to unbrick on the jelly bean OTA, use this thread if its doesnt work.
thanks again for another how to.
i'm downloading the files now there are two question:
1. TeddyOfLove require fastboot files on ICS I guess SPDREM_UMTS_01.6.7.xxx but why tutorial from HSD-Pilot doesn't require this file? which one should i follow
2. Based on above tutorial there are no CID restore? so when I restore it? after all works or before all steps start?
idwijayaku said:
thanks again for another how to.
i'm downloading the files now there are two question:
1. TeddyOfLove require fastboot files on ICS I guess SPDREM_UMTS_01.6.7.xxx but why tutorial from HSD-Pilot doesn't require this file? which one should i follow
2. Based on above tutorial there are no CID restore? so when I restore it? after all works or before all steps start?
Click to expand...
Click to collapse
1. I think you have to use HSD-Pilot's thread. If its doesnt work, use TeddyOfLove's post. Yes, download the fastboot files if you follow TeddyOfLove's post.
2. Use my tutorial how to restore it.
Sent from my GT-I9300 using xda app-developers app
I tried HSD-Pilot's step but stuck after update from external storage.
During "updating BP..." process I got this error
asserted failed: motoflash ("/tmp/bp.img")
now I will try teddyoflove step
I will update you asap.
TheMrcool212 said:
You had just erased cid? did i just told you how to restore cid?
.
Click to expand...
Click to collapse
I just wrote this part.
I have to erase my cid again, coz i can't go to any boot.
Screen just stuck on that error.
TheMrcool212 said:
1. I think you have to use HSD-Pilot's thread. If its doesnt work, use TeddyOfLove's post. Yes, download the fastboot files if you follow TeddyOfLove's post.
2. Use my tutorial how to restore it. Restore it after
Sent from my GT-I9300 using xda app-developers app
Click to expand...
Click to collapse
I've done tried with HSD-Pilot but stuck on updating BP process,
then I tried TeddyOfLove's post also:
still stuck on updating bp.. process:
I guess this is why I can't go to BP Tools
Did you restore the cid and flash the OTA?
Sent from my GT-N7100 using xda app-developers app
TheMrcool212 said:
Did you restore the cid and flash the OTA?
Sent from my GT-N7100 using xda app-developers app
Click to expand...
Click to collapse
As you said earlier, I must flash the OTA first then restore the cid.
This error appears during flashing the OTA