dear Developer
pleas help me out how to fix my samsung galalxy s3 , Swiss AUT version. my phone couldn't start or either be in recovery mode,,, i only can enter restore mode..
but using of odin ends up with fail,, there's no PIT for mapping,,, my phone is 16 gb. can you help me how to unbrick or fix this problem of Pit in order to flash normally in Odin? also i realized that when my phone in restore mode in the upper of sreen the custom No. is empty which is little bit weird because before it was Gt-i9300. now it is empty???
there might be something to do in order to fix,, i might wrongly diagnosed that it's SBS bricked board,,,
i feel very disappointed from buying this phone i wish if i didn't ,,,,,, Samsung company is selling crap phones that after 150 days it bricks spontaneously and there's no fix,,,, i hate it and i will buy another phone which is real phone not a piece of sheap plastic
:crying::crying:crying::crying:crying::crying:crying::crying
pleas help guys might be an answer to me:crying::crying
:
I am looking forward to hearing from you
regards:fingers-crossed:
Related
I have a huge problem with my galaxy s 2 T989 i tryed to flash pure ics rom on it but i did a real stupid move and i didnt do a full wipe before instaling it and now the phone will not boot at all not even download mode i am pulling my hair out the phone is not even 20 days old please help me i can really use some advice.
Sorry
I'm afraid you have bricked you phone. There is no way that I know that can recover your phone.
Hi all.
I have already posted my problem in this thread which I have read to the end ( [GUIDE] Fix an unflashable or soft bricked I9100G )
but was not able to get any solution so I'm starting a new thread hopefully someone might be able to help me and sorry if I was not suppose to start a new thread.
My problem is as follows and hope that someone can help.
I have downloaded odin mobile and installed it on my S2 I9100 G which previously had CM 10 installed on it and I wanted to flash the official firmware using Odin mobile. I did run it and then the phone prompted me for M5 or Md5 that was detected and should click yes to verify before flashing. I clicked yes then it started verifying and when it was done it rebooted and then was stuck on the (Samsung Galaxy S2 GT-19100G black screen) and did not want to move. I waited for an hour and a half and nothing happened. When I removed the battery (I could not reset or do anything else) and put it back, the phone turned on by itself and stayed still on the starting screen (Samsung Galaxy S2 GT-19100G black screen)
Now I'm not being able to put it in recovery nor download mode.
Can any one help and anyone knows if the jtag dongle can actually force it to go to download mode even at this stage
Thanks in advance for any suggestion
Ok thank you guys. I think I was able to fix it and revive my phone.
go to service centre they solve your problem
Sent from my GT-I9100G using xda premium
Make sure you got the right M.O kernel (I9100G).
Sent from the little guy
dear people
:highfive::highfive:
pleas help me out hot to fix my samsung galalxy s3 , Swiss AUT version. my phone couldn't start or either be in recovery mode,,, i only can enter restore mode.. but using of odin ends up with fail,, there's no PIT for mapping,,, my phone is 16 gb. can you help me how to unbrick or fix this problem of Pit in order to flash normally in Odin? also i realized that when my phone in restore mode in the upper of sreen the custom No. is empty which is little bit weird because before it was Gt-i9300. now it is empty???
pleas help :fingers-crossed:
I am looking forward to hearing from you
kind regards
dear Developer
pleas help me out how to fix my samsung galalxy s3 , Swiss AUT version. my phone couldn't start or either be in recovery mode,,, i only can enter restore mode..
but using of odin ends up with fail,, there's no PIT for mapping,,, my phone is 16 gb. can you help me how to unbrick or fix this problem of Pit in order to flash normally in Odin? also i realized that when my phone in restore mode in the upper of sreen the custom No. is empty which is little bit weird because before it was Gt-i9300. now it is empty???
there might be something to do in order to fix,, i might wrongly diagnosed that it's SBS bricked board,,,
i feel very disappointed from buying this phone i wish if i didn't ,,,,,, Samsung company is selling crap phones that after 150 days it bricks spontaneously and there's no fix,,,, i hate it and i will buy another phone which is real phone not a piece of sheap plastic
crying:crying:cryi ng::crying
pleas help guys might be an answer to me:crying
:
I am looking forward to hearing from you
regards
Hi just wanting some help from a android guru.
I did update my phones rom to a new update and the next morning somehow it said it failed to encrypt my phone which I did not ask it to.
Now my phone won't work. I can turn it on and get s3 splash screen and it does not go further.
I can get to cwm and download screen
When I try to flash via Odin it fails at nand flash fail.
I have tryed quite a few things. Please look at pic and if anyone can help please.
Sent from my SM-T530 using XDA Free mobile app
Try the rescue firmware and pit file, search general forum. If that falls to flash then first try downgrade to BLFB bootloader.
Hey
I get nand write fail ?
Sent from my SM-T530 using XDA Free mobile app
Sorry, emmc chip has failed/corrupted try the dead boot recovery but probably time for a new phone.
Yes, it is sudden death symptom. You need to replace nand chip or whole motherboard but it will cost you ca. 100 bucks. You could try to buy s3 with cracked screen and good motherboard and replace it. But there will be different IMEI and serial number of course but you can replace them with box in any service center. If your warranty is acctual then you should send it to Samsung service center.
It happens offen while upgrading to 4.3 directly from 4.1.2.
____________________________________________
P3110 / I9300 / I9100 / NEXUS 5 / iPAD2