Hello.
I'm not completely sure what happened, but my phone ran out of battery last night, and so after charging it this morning I tried to power it up, and was met by the following.
BUZZ PVT SHIP S-ON
HBOOT-1.01.0002
MICROP-0622
TOUCH PANEL-ATMELC03_16ac
RADIO-3.35.20.10
Dec 2 2010, 17:14:26
FASTBOOT
<VOL UP> to previous item
<VOL DOWN> to next item
<POWER> to select item
BOOTLOADER
REBOOT
REBOOT BOOTLOADER
POWER DOWN
However, my phone is not responding to any of the buttons, and I can't get past this page.
can anyone help me pass this?
I seems like that there is a chance that you have no rom on your phone anymore. Something similar happened to me and my phone would only boot in hboot because there was no rom to boot into. Can you get it recognized by your computer.
Sent from my HTC One using Tapatalk 4
WildfireDEV said:
I seems like that there is a chance that you have no rom on your phone anymore. Something similar happened to me and my phone would only boot in hboot because there was no rom to boot into. Can you get it recognized by your computer.
Sent from my HTC One using Tapatalk 4
Click to expand...
Click to collapse
When I connect it to the usb, it says "FASTBOOT USB", and it comes up as a removable drive on the computer, but I can't access it after that.
altharian13 said:
When I connect it to the usb, it says "FASTBOOT USB", and it comes up as a removable drive on the computer, but I can't access it after that.
Click to expand...
Click to collapse
now it isn't doing it at all now as a removable drive.
altharian13 said:
When I connect it to the usb, it says "FASTBOOT USB", and it comes up as a removable drive on the computer, but I can't access it after that.
Click to expand...
Click to collapse
Can you use fastboot on pc to see the device. To do so go to the folder you have adb and fastboot in and open it up in a command prompt then type fastboot devices while your phone is plugged in. If you see a bunch of numbers and letters and it says device then come back and reply to the thread. I probably won't answer for about another 8 hours as I am going to bed now. When I get up I will try and continue to help you.
Good night
Sent from my HTC One using Tapatalk 4
WildfireDEV said:
Can you use fastboot on pc to see the device. To do so go to the folder you have adb and fastboot in and open it up in a command prompt then type fastboot devices while your phone is plugged in. If you see a bunch of numbers and letters and it says device then come back and reply to the thread. I probably won't answer for about another 8 hours as I am going to bed now. When I get up I will try and continue to help you.
Good night
Sent from my HTC One using Tapatalk 4
Click to expand...
Click to collapse
Thank you loads, I am trying it now and I shall let you know what happens. Thank you so much.
Hey.
I have the programs installed, however have never had to use them before. I have watched several videos on what to do with this program but I keep getting stuck and confused. I have opened the command window and after trying to search I can not find the device on there. One tutorial I have been watching has got me so far, but I am stuck on it after that point. I've included a screenshot of what I've managed to get so far, any help would be greatly appreciated.
So when you type fastboot also type the word devices. Fastboot devices should show your phone if it is connected if so then we can go from there.
Sent from my HTC One using Tapatalk 4
I tried that, and after several attempts and have got it, it says
"HT06FPY06765 fastboot"
I'm sorry if I don't reply, as it's getting late and I need to sleep soon. I'll be so great full for anymore help you can give me on this issue. Thank you =)
altharian13 said:
I'm sorry if I don't reply, as it's getting late and I need to sleep soon. I'll be so great full for anymore help you can give me on this issue. Thank you =)
Click to expand...
Click to collapse
Yeah sure that okay. Well now that it seems that your phone is being recongnized by the computer. Okay now just tell me if your hardware buttons work at all when you are in hboot.
no, my hardware buttons don't work at all, I can't do anything on the phone to change the original screen.
So the power button doesn't work either.
Sent from my HTC One using Tapatalk 4
---------- Post added at 06:22 PM ---------- Previous post was at 06:21 PM ----------
Because It is going become much harder but I will try and help you to the best of my ability.
Sent from my HTC One using Tapatalk 4
WildfireDEV said:
So the power button doesn't work either.
Sent from my HTC One using Tapatalk 4
---------- Post added at 06:22 PM ---------- Previous post was at 06:21 PM ----------
Because It is going become much harder but I will try and help you to the best of my ability.
Sent from my HTC One using Tapatalk 4
Click to expand...
Click to collapse
no, the power button doesn't work either. Thank you.
Seeing that your fastboot seems to work try relocking your bootloader through fastboot and download the ruu for your phone with the corresponding carrier from androidfiles ruu. Remember to select buzz if this doesn't work please report back.
Sent from my HTC One using Tapatalk 4
WildfireDEV said:
Seeing that your fastboot seems to work try relocking your bootloader through fastboot and download the ruu for your phone with the corresponding carrier from androidfiles ruu. Remember to select buzz if this doesn't work please report back.
Sent from my HTC One using Tapatalk 4
Click to expand...
Click to collapse
I'm looking at androidfiles ruu, however they do not have one for my phone ( as it's the original HTC "wildfire"). what would you suggest I do for this?
altharian13 said:
I'm looking at androidfiles ruu, however they do not have one for my phone ( as it's the original HTC "wildfire"). what would you suggest I do for this?
Click to expand...
Click to collapse
Look for the name buzz.
Sent from my HTC One using Tapatalk 4
WildfireDEV said:
Look for the name buzz.
Sent from my HTC One using Tapatalk 4
Click to expand...
Click to collapse
I have selected buzz, and have downloaded the file which I think is correct for my phone and I am getting a usb connection error from the ruu program, although it says it's connected on the phone.
altharian13 said:
I have selected buzz, and have downloaded the file which I think is correct for my phone and I am getting a usb connection error from the ruu program, although it says it's connected on the phone.
Click to expand...
Click to collapse
Have you installed all the htc drivers.
Sent from my HTC One using Tapatalk 4
When I installed sdk, I downloaded the "Google USB Driver" along with it, as it said to do
Related
Just been released for devs http://revolutionary.io/
Thanks Guys
Sorry, already covered
already got it running on the view and 3d lol
Happy Friday! This is awesome! Need some perma-root and CWM action now!
Sounds like it's almost time to start building a custom rom :-D
Sent from my SPH-D700 using XDA App
contradude said:
Sounds like it's almost time to start building a custom rom :-D
Sent from my SPH-D700 using XDA App
Click to expand...
Click to collapse
AOSP Honeycomb? We wish.
Worked perfectly
Revolutionary went smoothly on my flyer and evo 3d. got flyer recovery too.
How do u install it? Did u just plug ur flyer to the computer and double click the revolutionary application file in the zip?
Sent from my PC36100 using XDA Premium App
no support
no support for flyer Hboot 1.07.0000
Well on the revolutionary site it mentions you need to install the htc drivers if you're on windows. Past that, turn on development in phone settings/application, and run the exe file. Easy stuff.
viera77 said:
no support for flyer Hboot 1.07.0000
Click to expand...
Click to collapse
Same with mine - no support for Flyer with HBOOT 1.07.x
I'd settle for making sure there is no carrier IQ in the view and optimising the ROM for the hardware. I'm currently in the process of figuring out what phone the flyer/view is most like to see which tweaks will work properly.
Just ran this on my view hboot 1.09 through ubuntu and it took less than 3 minutes...maybe less than that. Gonna try and see if my recovery and rooted images work.
Using:
Windows 7 64 Bits
Flyer P510e 3G/32GB
HBoot 1.100.000
ROM: 1.48.707.3
I couldn't get it to work.
___________________________________________________________
Acquring root (method 3)
Sending in Caroline...
Cleaning up...
Rebooting to fastboot...
When life gives you lemons, don't make lemondae. Make lfe take the lemonade back!
Waiting for fastboot...
Rebooting to fastboot (Once moar...)
FAILED - Go have some lemonade!
Press (almost) any key to exit.
_____________________________________________________________
Device stuck in fastboot.
What have I done wrong?
Mine did the same thing, just choose Power Down and then turn it back on holding down the vol - key. You should be in S-Off now!
[email protected] said:
Using:
Windows 7 64 Bits
Flyer P510e 3G/32GB
HBoot 1.100.000
ROM: 1.48.707.3
I couldn't get it to work.
___________________________________________________________
Acquring root (method 3)
Sending in Caroline...
Cleaning up...
Rebooting to fastboot...
When life gives you lemons, don't make lemondae. Make lfe take the lemonade back!
Waiting for fastboot...
Rebooting to fastboot (Once moar...)
FAILED - Go have some lemonade!
Press (almost) any key to exit.
_____________________________________________________________
Device stuck in fastboot.
What have I done wrong?
Click to expand...
Click to collapse
StormMcCloud said:
Mine did the same thing, just choose Power Down and then turn it back on holding down the vol - key. You should be in S-Off now!
Click to expand...
Click to collapse
i'm having the same problem too and did wat you told but mine still show S-ON !
xtrememanix said:
i'm having the same problem too and did wat you told but mine still show S-ON !
Click to expand...
Click to collapse
Make sure the device has fastboot turned on. To do this turn the device off, boot into recovery (power + volume down) then navigate to where it says fastboot, tap the power button once, then reboot the flyer and try the exploit again.
same here and i'm now need to go pee as having too much lemonade
Still not working on my Flyer 32G 3G Thailand Retail HBOOT 1.10.0000
Fastboot was showing during the process and driver install correctly but still fail
Did you make sure fastboot was on via the steps I described in the earlier post? I from the looks of the errors its acting like its not. Do the steps I mentioned and my previous post and try again and let me know what happens. If you already tried that let me know so I can keep on thinking about possible fixes.
andmaf said:
Did you make sure fastboot was on via the steps I described in the earlier post? I from the looks of the errors its acting like its not. Do the steps I mentioned and my previous post and try again and let me know what happens. If you already tried that let me know so I can keep on thinking about possible fixes.
Click to expand...
Click to collapse
=First run Revolutionary=
Yes the fastboot page was on during the process, first trial the driver was recognize and the second try the driver was there already.
=Second and Third run Revolutionary=
Same same after phone revoot to FASTBOOT screen and pause there . . the program ask for second try and i get lemonade
I look in the device manager it show only HTC Sync under android . . is it correct? shouldn't it show fastboot driver?
So I've finally decided to unlock and have managed to install clockworkmod to my Prime.
I am now trying to install nvflash because I hear it's supposed to prevent me from bricking my tablet. Booting into fastboot is not a problem for me, but the problem appears when I'm using the cmd prompt and trying to reach the device.
I've used all the correct commands as shown on the nvflash guide, but the tablet doesn't seem to acknowledge them. Using a command like fastboot reboot shows successful on my computer, but does not actually physically reboot the tablet.
Any help on this matter would be very appreciated. Seems like I keep going in circles and nothing will work
Post deleted by user.
Post deleted by user.
kenny98023 said:
This is exactly my problem as well. If I attempt to flash ebtblob.bin, fastboot says it works, but doesn't. If I reboot from fastboot before attempting the flash it will reboot the prime.
Sent from my Galaxy Nexus using xda premium
---------- Post added at 02:11 PM ---------- Previous post was at 02:06 PM ----------
BTW... I've just unlocked since JB and have not rooted yet.
Sent from my Galaxy Nexus using xda premium
Click to expand...
Click to collapse
I'm guessing you discovered that if you are on JB you can't enable nvFlash anymore.
---------- Post added at 10:37 AM ---------- Previous post was at 10:34 AM ----------
Leinhart_6 said:
So I've finally decided to unlock and have managed to install clockworkmod to my Prime.
I am now trying to install nvflash because I hear it's supposed to prevent me from bricking my tablet. Booting into fastboot is not a problem for me, but the problem appears when I'm using the cmd prompt and trying to reach the device.
I've used all the correct commands as shown on the nvflash guide, but the tablet doesn't seem to acknowledge them. Using a command like fastboot reboot shows successful on my computer, but does not actually physically reboot the tablet.
Any help on this matter would be very appreciated. Seems like I keep going in circles and nothing will work
Click to expand...
Click to collapse
Did you try going through the entire recommended steps of uninstalling the Asus drivers and then installing the naked drivers? You can find them in the development area. Also some folks have had issues with cwm on the Prime so the generally accepted recovery to use is TWRP which you should have seen if you read thoroughly the threads in the development area. Are you certain the files weren't generated? Please, Please read up more before you do anything more or you could easily end up with a plastic, glass and metal paperweight.
Post deleted by user.
fastboot wont recognize tablet
fastboot wont recocnize my tablet, which is in fastboot mode. i have tried the standard asus drivers, the whole pc suite, the naked drivers, still doesnt work. adb recognizes it just fine when i boot android, but as soon as i get to "Fastboot USB protocol" its off the hook...weird think also is, that in device manager it is listed under "SAMSUNG android phone>ASUS fastboot interface"
i also tried to uninstall all my samsung drivers (i9100), still it wont be recognized...
anyone any ideas??
kenny98023 said:
Thanks for putting more salt in the wound. Going to not proceed any further until I can get a blob of my device made. Too much $ to F with.
Sent from my Galaxy Nexus using xda premium
Click to expand...
Click to collapse
Not my intention to rub salt. sorry you are having issues but there is a lot of good information to be had if you read read read and you are right that it is too Mich money to fool around with.
Hello,
I've read numerous times about people being able to restore their dead bricked phones. No button combination will get my LG Optimus L9 P769 (T-mobile) to turn on. I think bricked it while trying to complete a carrier unlock. I understand that I can try to restore my phone through either fastboot or kdz. For fastboot, I was able to install the omap driver, but you know how I'm supposed to install a second driver? Well, I can't seem to do that. Maybe I'm doing something wrong? I would love an explanation of how to install the driver a second time. I know I'm doing something wrong, because when I use the fastboot script to flash the xloader and uboat, I just get "waiting for device." Also, if I want to flash a kdz, do I need fastboot drivers? I feel like my success depends on installing the fastboot drivers properly, but my computer and two others would not let me do that.
I'm really new to this stuff, so any help is appreciated! Also, please excuse me if I'm using the terminology incorrectly. Like I said, I'm new to all this.
Thank you in advance!
To install a kdz, you need to be in upgrade mode. Hold the volume up button then connect it to the computer.
Sent from my LG-P769 using XDA Premium 4 mobile app
LaDY Vengeance said:
To install a kdz, you need to be in upgrade mode. Hold the volume up button then connect it to the computer.
Sent from my LG-P769 using XDA Premium 4 mobile app
Click to expand...
Click to collapse
What if the phone doesn't turn on? Does it still go into upgrade mode?
Yes.
Sent from my LG-P769 using XDA Premium 4 mobile app
LaDY Vengeance said:
Yes.
Sent from my LG-P769 using XDA Premium 4 mobile app
Click to expand...
Click to collapse
Ok thanks! I shall try later!
Did it work? I think you should Do fastboot.. that's what I used when mines didn't power on..
Sent from my LG-P769 using XDA Premium HD app
Linux
Get a live linux distribution and try this:
http://vincenzoml.blogspot.it/2013/08/lg-l9-unbrick-script.html
LaDY Vengeance said:
Yes.
Sent from my LG-P769 using XDA Premium 4 mobile app
Click to expand...
Click to collapse
Hello,
So I finally tried what you said, but it didn't work. Which program should I use to flash the kdz? Also, when I press up, should the phone have the battery inserted or not? When I tried the KDZ Updater, it said phone was not found.
simfate said:
Hello,
So I finally tried what you said, but it didn't work. Which program should I use to flash the kdz? Also, when I press up, should the phone have the battery inserted or not? When I tried the KDZ Updater, it said phone was not found.
Click to expand...
Click to collapse
You need to install ICS x and u boot then flash KDZ by offline method.
Nathan.7118391 said:
You need to install ICS x and u boot then flash KDZ by offline method.
Click to expand...
Click to collapse
Hello, I can't get into fastboot. It may be that the phone battery does not have a charge and so the fastboot script does not recognize it when I insert it into the phone after 4 seconds. Could that be a possibility? Because I tried everything, tried many different timings many times, to no avail!
simfate said:
Hello, I can't get into fastboot. It may be that the phone battery does not have a charge and so the fastboot script does not recognize it when I insert it into the phone after 4 seconds. Could that be a possibility? Because I tried everything, tried many different timings many times, to no avail!
Click to expand...
Click to collapse
I was just in the same boat as you and pretty much gave up hope but finally got fastboot working and flashed ics x and u and bam it worked like a charm on offline flash method. You just have to pit usb cable in phone w/o battery in and go to device manager. When you see it popup under other devices right click and press install driver. Make sure you have electronic signatures disabled or it will give a error and not install. This is what prevented me from getting it to work the first 100 times! Now run CMD. TYPE CD C:/FASTBOOT < OR C:/ W/E FOLDER NAME IT IS. THEN RUN START.BAT. < OR W/E THE .BAT FILE INSIDE YOUR FILE IS NAMED. Now press enter. It should prompt to plug in phone. I put my battery in as soon as plugged in and it worked. Now Choose option 5. Let it do its thing. Now go reinstall driver as done before to be safe. Then remove your battery. Hold volume + button and plug usb in. S/W upgrade mode should come up. Slide your battery in and proceed to the offline flash method to flash you kdz file. Should be alive again! Mine was tricky going into sw upgrade mode. Sometimes it came right up then sometimes it took 4 or 5 tries so dont give up! Goodluck and you can do it! I almost gave up I felt so hopeless about getting it to work then it finally worked like a charm!
lwg45714 said:
I was just in the same boat as you and pretty much gave up hope but finally got fastboot working and flashed ics x and u and bam it worked like a charm on offline flash method. You just have to pit usb cable in phone w/o battery in and go to device manager. When you see it popup under other devices right click and press install driver. Make sure you have electronic signatures disabled or it will give a error and not install. This is what prevented me from getting it to work the first 100 times! Now run CMD. TYPE CD C:/FASTBOOT < OR C:/ W/E FOLDER NAME IT IS. THEN RUN START.BAT. < OR W/E THE .BAT FILE INSIDE YOUR FILE IS NAMED. Now press enter. It should prompt to plug in phone. I put my battery in as soon as plugged in and it worked. Now Choose option 5. Let it do its thing. Now go reinstall driver as done before to be safe. Then remove your battery. Hold volume + button and plug usb in. S/W upgrade mode should come up. Slide your battery in and proceed to the offline flash method to flash you kdz file. Should be alive again! Mine was tricky going into sw upgrade mode. Sometimes it came right up then sometimes it took 4 or 5 tries so dont give up! Goodluck and you can do it! I almost gave up I felt so hopeless about getting it to work then it finally worked like a charm!
Click to expand...
Click to collapse
I have a question, can a computer detect the phone with the battery in it? Like the omap4430 usb device? Because for me, the computer detects it whether the battery is in or not... both ways.
simfate said:
I have a question, can a computer detect the phone with the battery in it? Like the omap4430 usb device? Because for me, the computer detects it whether the battery is in or not... both ways.
Click to expand...
Click to collapse
Yes it will detect it. However you need to install the omap in two different locations for it to work.
Sent from my LGMS769 using XDA Premium 4 mobile app
kuma82 said:
Yes it will detect it. However you need to install the omap in two different locations for it to work.
Sent from my LGMS769 using XDA Premium 4 mobile app
Click to expand...
Click to collapse
The problem is, I can't install the driver in the second location because it doesn't come up in device manager.. I was thinking maybe there's a problem with the battery, like it doesn't have a charge or something. Because when I run fastboot it doesn't detect the battery no matter what timing I used. I tried everything. If I use the old fastboot script and I get to "fastboot? y or N" and I enter y, it keeps asking the same question.
simfate said:
The problem is, I can't install the driver in the second location because it doesn't come up in device manager.. I was thinking maybe there's a problem with the battery, like it doesn't have a charge or something. Because when I run fastboot it doesn't detect the battery no matter what timing I used. I tried everything. If I use the old fastboot script and I get to "fastboot? y or N" and I enter y, it keeps asking the same question.
Click to expand...
Click to collapse
Have you read my post about enabling hidden/inactive devices in device manager?
If you havent you should read it and if you have
When the inverted fastboot pops up (on your phone) remove the usb and place it back in.
---------- Post added at 04:16 AM ---------- Previous post was at 04:11 AM ----------
simfate said:
The problem is, I can't install the driver in the second location because it doesn't come up in device manager.. I was thinking maybe there's a problem with the battery, like it doesn't have a charge or something. Because when I run fastboot it doesn't detect the battery no matter what timing I used. I tried everything. If I use the old fastboot script and I get to "fastboot? y or N" and I enter y, it keeps asking the same question.
Click to expand...
Click to collapse
Have you read my post about enabling hidden/inactive devices in device manager?
If you havent you should read it and if you have
When the inverted fastboot pops up (on your phone) remove the usb and place it back in, this should make the driver pop up.
kuma82 said:
Have you read my post about enabling hidden/inactive devices in device manager?
If you havent you should read it and if you have
When the inverted fastboot pops up (on your phone) remove the usb and place it back in.
---------- Post added at 04:16 AM ---------- Previous post was at 04:11 AM ----------
Have you read my post about enabling hidden/inactive devices in device manager?
If you havent you should read it and if you have
When the inverted fastboot pops up (on your phone) remove the usb and place it back in, this should make the driver pop up.
Click to expand...
Click to collapse
Yes, i've read that post (I think I've read everything on xda related to fastboot!) I don't get an inverted fastboot on the phone's screen. My phone doesn't turn on at all.. Like I said, I'm still struggling to get into fastboot.
Could be a problem with the battery? I'm going to get an external battery charger and try charging the battery.
simfate said:
Yes, i've read that post (I think I've read everything on xda related to fastboot!) I don't get an inverted fastboot on the phone's screen. My phone doesn't turn on at all.. Like I said, I'm still struggling to get into fastboot.
Could be a problem with the battery? I'm going to get an external battery charger and try charging the battery.
Click to expand...
Click to collapse
How did your device get in this state? Depending on what happened your device may not be fixable.
Sent from my LGMS769 using XDA Premium 4 mobile app
kuma82 said:
How did your device get in this state? Depending on what happened your device may not be fixable.
Sent from my LGMS769 using XDA Premium 4 mobile app
Click to expand...
Click to collapse
It died after I plugged it into the computer. I never rooted it and has the stock software. Before dying I also carrier-unlocked it using a cheap code from ebay.
Hi people from the comunity of xda-developers, I have recently got a new HTC ONE from AT&T and my problem is that, I CANT Unlock the bootloader of my htc one. I have found threads about how people can unlock their bootloader but they are from the phones who where in hboot 1.44.000 ... Is there any way i can unlock the bootloader?. I went to HTCDEV.COM and i tried to unlock it, but when i go to command prompt and continue with the "fastboot oem etc"it gets stuck in waiting device and it doesnt do anything. I Have installed and uninstalled the drivers a couple of times and nothing... Im using Windows 8 and i dont know if there is a problem using it. BTW when i go to Device Manager and look for my phone i see that in portable devices it says android 1.0 with a triangle i tried to update the drivers but got no luck either.
If any of you people can help me i would be very happy... ohh and Thanks in Advance
PD: Im from Puerto Rico and my main language is Spanish so im truly sorry if guys find some grammar errors and i tried to follow the rules, if i posted it wrong PLEASE DONT DELETE IT, just tell me and i make the question in the right place! Thankls again
E.N.O123 said:
Hi people from the comunity of xda-developers, I have recently got a new HTC ONE from AT&T and my problem is that, I CANT Unlock the bootloader of my htc one. I have found threads about how people can unlock their bootloader but they are from the phones who where in hboot 1.44.000 ... Is there any way i can unlock the bootloader?. I went to HTCDEV.COM and i tried to unlock it, but when i go to command prompt and continue with the "fastboot oem etc"it gets stuck in waiting device and it doesnt do anything. I Have installed and uninstalled the drivers a couple of times and nothing... Im using Windows 8 and i dont know if there is a problem using it. BTW when i go to Device Manager and look for my phone i see that in portable devices it says android 1.0 with a triangle i tried to update the drivers but got no luck either.
If any of you people can help me i would be very happy... ohh and Thanks in Advance
PD: Im from Puerto Rico and my main language is Spanish so im truly sorry if guys find some grammar errors and i tried to follow the rules, if i posted it wrong PLEASE DONT DELETE IT, just tell me and i make the question in the right place! Thankls again
Click to expand...
Click to collapse
Download HTC sync manager, install it.
Go to control panel, uninstall programs and remove HTC sync manager but don't uninstall HTC drivers.
connect device to the computer and let the PC install drivers. Once done remove HTC from PC, place HTC on boot loader mode and select fastboot and connect device to computer, let the computer install android 1.0
Once installed on command prompt go to where you have the SDK and type fastboot devices, if the HTC one shows up you are good to go
Sent from my HTC One using xda app-developers app
TopoX84 said:
Download HTC sync manager, install it.
Go to control panel, uninstall programs and remove HTC sync manager but don't uninstall HTC drivers.
connect device to the computer and let the PC install drivers. Once done remove HTC from PC, place HTC on boot loader mode and select fastboot and connect device to computer, let the computer install android 1.0
Once installed on command prompt go to where you have the SDK and type fastboot devices, if the HTC one shows up you are good to go
Sent from my HTC One using xda app-developers app
Click to expand...
Click to collapse
I have everything installed, but when i go to android 1.0 it has a triangle and i dont know if there is a problem with that..
Btw where should the SDK be in what folder?? That's the only part where i got lost! Is there any tutorial of this?.. Thanks Again and Thanks to you for your reply!
Sent from my HTC One using Tapatalk
E.N.O123 said:
I have everything installed, but when i go to android 1.0 it has a triangle and i dont know if there is a problem with that..
Btw where should the SDK be in what folder?? That's the only part where i got lost! Is there any tutorial of this?.. Thanks Again and Thanks to you for your reply!
Sent from my HTC One using Tapatalk
Click to expand...
Click to collapse
My HTC One will be arriving in a few days, I'll let you know if I'm able to proceed further past this point and get you past it. In the meantime, I'm gonna scan the other threads for different methods and get back to you if I find anything solid.
Sent from my LG-E970 using XDA Premium 4 mobile app
---------- Post added at 05:03 AM ---------- Previous post was at 04:20 AM ----------
I meant in terms of the rooting process. As for SDK, here's a helpful guide by Senior Member Apex, all credit goes to him: http://forum.xda-developers.com/showthread.php?t=1842969
Sent from my LG-E970 using XDA Premium 4 mobile app
Hey guys i have been using my dell tablet for more than a year. I also rooted it at the same time i bought the tab. Now a week ago when i was using my tab it was completly turned off. I have tried charging it for a day nothing happens. it dosent Show any Boot animation or charging animation nor does it even enter fastboot mode. It doesn't even turn on. It has just become like a paper weight. When i connect it to pc, it shows under the Device Manager CLOVERVIEW PLUS Device. I checked out some other posts and it shows reflashing it through xFTSK, but i searched everywhere but it doesn't have any firmware or software for Dell Venue 7 HSPA+ 3730. Pls Guys Help me out here, really appreciated. Thanks.
can you boot into the fastboot mode?
Huzaifa_Aziz said:
can you boot into the fastboot mode?
Click to expand...
Click to collapse
No, I cannot. it doesn't give any response, only when conected to pc it shows CloverView Plus in Device Manager.
ssjdeepanshu said:
No, I cannot. it doesn't give any response, only when conected to pc it shows CloverView Plus in Device Manager.
Click to expand...
Click to collapse
I'm really sorry for replying late, was stuck in an issue of my own with S6 Edge, okay so, when you put it on charge does it show up "charging" ?? like the Cell with charging animation shows up?
---------- Post added at 04:10 AM ---------- Previous post was at 03:56 AM ----------
ssjdeepanshu said:
No, I cannot. it doesn't give any response, only when conected to pc it shows CloverView Plus in Device Manager.
Click to expand...
Click to collapse
if it is showing up a response in Device Manager then it means your boot is still alive. There is hope brother, so first of all we need to know if it has juice or not?
also please READ some stuff here http://forum.xda-developers.com/android/development/intel-android-devices-root-temp-cwm-t2975096
and download and extract this package http://https://www.androidfilehost.com/?fid=23622183712464837 from @social-design-concepts and please don't flash stuff just right away. I would suggest that you read first what they have to say, then cautiously proceed with the Toolkit.
do also thank @social-design-concepts on his thread by the way.. :good:
---------- Post added at 04:25 AM ---------- Previous post was at 04:10 AM ----------
ssjdeepanshu said:
No, I cannot. it doesn't give any response, only when conected to pc it shows CloverView Plus in Device Manager.
Click to expand...
Click to collapse
and then there is the good old METHOD number 2,
it's easier as far as I know,
make an easy ADB folder.
Just boot in FASTBOOT mode.
extract the ::Venue_7_3G_KK4.4.2v1.33_FLASHPKG.7z:: archive
and take out Venue_7_3G_KK4.4.2v1.33.system.img.gz (place it in same folder as adb.
after that in fastboot mode
write command
fastboot flash system Venue_7_3G_KK4.4.2v1.33.system.img.gz
Click to expand...
Click to collapse
wait for it to finish.
after that fastboot reboot
and profit!
Sorry for replying late, but as i said earlier it doesn't show any charging animation or enters the fastboot mode but when connected to pc it shows CloverView Plus in the device manager. i am just confused is it even alive or not.....
ssjdeepanshu said:
Sorry for replying late, but as i said earlier it doesn't show any charging animation or enters the fastboot mode but when connected to pc it shows CloverView Plus in the device manager. i am just confused is it even alive or not.....
Click to expand...
Click to collapse
It might be possible that the charging IC has been damaged, if after a continuous 2/3 hour connection with PC/charger the tablet does not turn on. Means it isn't getting enough charge to even boot up. It might be a good idea to get it checked by a technician but I am afraid parts/ replacements and finding an expert on Dell devices is quiet rare because of it's less popularity.
yeah even i am thinking it is a hardware problem, if i was a software problem, i might have been able to solve it on my own.
Anyway's thanks for help.
ssjdeepanshu said:
yeah even i am thinking it is a hardware problem, if i was a software problem, i might have been able to solve it on my own.
Anyway's thanks for help.
Click to expand...
Click to collapse
You are welcome!
I wonder what became of your tablet...
Huzaifa_Aziz said:
You are welcome!
I wonder what became of your tablet...
Click to expand...
Click to collapse
It's now just a useless paper weight :crying:
ssjdeepanshu said:
It's now just a useless paper weight :crying:
Click to expand...
Click to collapse
you know I found that tablet to be indestructible. up till now at least. still running even though I corrupted its recovery once.