Hi guys,
My Motorola BackFlip MB300 can access to Bootloader Init and can flash firmware by RSD tool but when it reboot only can display to Motorola Logo and silent forever. I change some firmware but it didn't any change. Hope that everyone will have right way to help me! Thank for read my post!
CyanogenVietNam said:
Hi guys,
My Motorola BackFlip MB300 can access to Bootloader Init and can flash firmware by RSD tool but when it reboot only can display to Motorola Logo and silent forever. I change some firmware but it didn't any change. Hope that everyone will have right way to help me! Thank for read my post!
Click to expand...
Click to collapse
all i think first was flashing SBF file on AP Fastboot mode
is it failed?
666satyr666 said:
all i think first was flashing SBF file on AP Fastboot mode
is it failed?
Click to expand...
Click to collapse
Yes, man! It's also fail...Plz help me with other way...
CyanogenVietNam said:
Yes, man! It's also fail...Plz help me with other way...
Click to expand...
Click to collapse
firmware for your device.
You need to download these things...
RSD Lite 4.5.7
AT&T Stock Android 2.1 Blur v3.0.1390 - Original SBF by Skrilax_CZ @ ModMyMobile
And if you're doing this and haven't attempted root yet, or would just like to wipe your device through and through, HERE are the Moto USB drivers. Make sure to get the correct installer for x86 or x64.
Install your USB Drivers (if you haven't already)
Install RSD Lite
Turn off your backflip
Plug the USB cable into the phone and computer
Open the keyboard and press J+D+Power simultaneously and let up when you see the blue recovery screen with the black moto batwings. In the bottom left corner of the screen it will say in white letters "USB init mode"
Now when the phone boots to the recovery screen, Windows will begin installing a driver for the MSM720x flash recovery mode.
After the driver has successfully installed, open RSD Lite
Upon opening RSD Lite, you should notice ONE connected device in the table below. If not, post what you did exactly and we can help
Now that the device is showing in RSD Lite, click the "..." browse button to point to the Android 2.1 Blur 3.0.1390 image you downloaded earlier
Once that's selected, press start to start flashing your phone.... DO NOT UNPLUG UNTIL IT'S FINISHED.
Once finished, it will reboot itself and you should be presented with the Android Setup after a minute or two.
Related
was going from gingerblur 2.5 on 1.56 then sbf to 1.83 and now it just says that after flashing.
tried to sbf 1.23 and 56 and same thing
am i doing something wrong?
in the rsdlite it sees the phone but says n/a for everything
Please HELP
Updated: I tried again fresh start on different computer and it worked!
must have been error in download, unzip, or there is something conflicting on my pc
hi i have same problem , went i flash OLYFR_U4_1.8.3_SIGNED_OLPSATTSPE_P013_HWolympus_1g_Service1FF.sbf ,
always after finish and rebooting then failed to boot 4 error raise,
i have use other computer to flash and the result is same failed to boot 4
i have install
- RSD Lite and 5.0
- Handset_USB_Driver_32_v4.9.0
plz can anyone help me ?
Sbf 4.1.26 or 4.1.57, then OTA to 4.1.83, root, sideload enable, flash CWM, flash GingerBlur.
bullghost said:
hi i have same problem , went i flash OLYFR_U4_1.8.3_SIGNED_OLPSATTSPE_P013_HWolympus_1g_Service1FF.sbf ,
always after finish and rebooting then failed to boot 4 error raise,
i have use other computer to flash and the result is same failed to boot 4
i have install
- RSD Lite and 5.0
- Handset_USB_Driver_32_v4.9.0
plz can anyone help me ?
Click to expand...
Click to collapse
i have the same problem
aaurnab said:
i have the same problem
Click to expand...
Click to collapse
please help
CaelanT said:
Sbf 4.1.26 or 4.1.57, then OTA to 4.1.83, root, sideload enable, flash CWM, flash GingerBlur.
Click to expand...
Click to collapse
thanks bro, i thinks that's the best way to update till 4.1.83,
here a little experience i have done
first time i try flash sbf 4.1.83 failed with that error booting,
and pull battery and back again to turn off the phone, and i flash the 1.26
then success with sim card inside,
iam not happy with failing on flash 4.1.83, then i thought the 4.1.83 sbf file is corrupt then i redownload again , after finish download,
i do the second time flashing with new 4.1.83 sbf
this second time is so frustrated, couz it fail again with same error.
until i have success full recover my atrix i do over 10 time flashing
and changing between computer and my notebook
and changing from windows 7 and windows XP
flashing random sbf from 1.83 and 1.26
the lasting i lost my hope , then suddenly the flash was success, WTF ,
lasting i remember is i pull the battery and pull out the sim card , then put back the battery, and do the flash,
the last time i flash 1.26 sbf
i thing
there is something no right with driver or RSD Lite not sync or missing something
until now iam still don't know how to solve it ,
pls anyone can find out what the problem and how to solve it
After about 4-5 hours and 7-8 tries using sfb method to upgrade to 1.83, I finally have a working phone again.
As to how I got stuck on the:
boot fail 4
starting RSD
and in RSD Lite, the phone's device name showing up as "SE Flash Olympus"
I decided to do a few things.
1. Go download the newest USB drivers. the 2.00.52 is what you should be on. If you can't find them, go to Motorola website and get MotoHelper 5.0 or whatever..install and then update your drivers. Restart your pc and keep trying to update your drivers until you get to USB 2.00.52 drivers.
2. USE THE ORIGINAL DATA CABLE THAT CAME WITH THE PHONE.
3. Make sure the connections are not loose at all (could've been why mine was messing up)
4. If you already have motohelper installed...go to the 'driverinstaller.exe' change operation mode to clean and reinstall, make sure the phone is unplugged. and click on start. (note, this part will be anywhere from 2 - 5 minutes depending on speed of your computer)
5. Restart RSD Lite, make sure you're using the latest one, and 'Run as administrator'.
**Go to config>Flash/Flex options... > only "check" Restart after Flexing..**
6. Now, I learned this the hard way...and many forums have it up there... GET YOUR BATTERY TO ABOVE 80% or IT WILL FAIL. (I had to go to a friend's at midnight to charge my battery from his atrix...hahaha)
7. Now turn your phone on again and it'll go to the "failed to boot 4 starting RSD" ...
8. Next, plug it in to your USB cable and click "Show Device" and then click once under the "USB 1 line" to view the device information at the top left. (Everything should be N/A except for your bootloader and you will also read "NS Flash Olympus now, instead of the SE Flash Olympus)
9. Put that '1.83_pudding.sfb' file in the "C:\ " directory to avoid any further complications.
10. Select the "...." browse to the '1.83_pudding.sfb' file and click start. It should work.... Now if it doesn't work... try and try again...
What I did was switched back and forth from 1.23 to 1.83... when I got mine to work, the device was registering as "SE Flash Olympus".
And for the longest time under bootloader, it would register as N/A...I finally decided to switch cables and it worked... once again, make sure to follow these:
* Full battery/80% above
* Stock Atrix USB cable
* 2.00.52 USB drivers
* RSD Lite 5.3.1
EDIT: GOOD LUCK! PM me if you need more assistance as those forward to XDA app
vash8806 said:
After about 4-5 hours and 7-8 tries using sfb method to upgrade to 1.83, I finally have a working phone again.
As to how I got stuck on the:
boot fail 4
starting RSD
and in RSD Lite, the phone's device name showing up as "SE Flash Olympus"
I decided to do a few things.
1. Go download the newest USB drivers. the 2.00.52 is what you should be on. If you can't find them, go to Motorola website and get MotoHelper 5.0 or whatever..install and then update your drivers. Restart your pc and keep trying to update your drivers until you get to USB 2.00.52 drivers.
2. USE THE ORIGINAL DATA CABLE THAT CAME WITH THE PHONE.
3. Make sure the connections are not loose at all (could've been why mine was messing up)
4. If you already have motohelper installed...go to the 'driverinstaller.exe' change operation mode to clean and reinstall, make sure the phone is unplugged. and click on start. (note, this part will be anywhere from 2 - 5 minutes depending on speed of your computer)
5. Restart RSD Lite, make sure you're using the latest one, and 'Run as administrator'.
**Go to config>Flash/Flex options... > only "check" Restart after Flexing..**
6. Now, I learned this the hard way...and many forums have it up there... GET YOUR BATTERY TO ABOVE 80% or IT WILL FAIL. (I had to go to a friend's at midnight to charge my battery from his atrix...hahaha)
7. Now turn your phone on again and it'll go to the "failed to boot 4 starting RSD" ...
8. Next, plug it in to your USB cable and click "Show Device" and then click once under the "USB 1 line" to view the device information at the top left. (Everything should be N/A except for your bootloader and you will also read "NS Flash Olympus now, instead of the SE Flash Olympus)
9. Put that '1.83_pudding.sfb' file in the "C:\ " directory to avoid any further complications.
10. Select the "...." browse to the '1.83_pudding.sfb' file and click start. It should work.... Now if it doesn't work... try and try again...
What I did was switched back and forth from 1.23 to 1.83... when I got mine to work, the device was registering as "SE Flash Olympus".
And for the longest time under bootloader, it would register as N/A...I finally decided to switch cables and it worked... once again, make sure to follow these:
* Full battery/80% above
* Stock Atrix USB cable
* 2.00.52 USB drivers
* RSD Lite 5.3.1
EDIT: GOOD LUCK! PM me if you need more assistance as those forward to XDA app
Click to expand...
Click to collapse
People 51_OLL iron-4.5.2A-lite 5.6 rsd 49_SIGNED_STABLE45LAOLYMPGBPERAR_P011_A026_M001_HWpd_Service1FF with ... and my error:
"Failde to boot 4"
rsd starting mode
I am reading is the battery problem that has to be for 80 %+...
If I turn on the power but the volume key + I fastboot protocol enters
If it lights only the error:
"Failde to boot 4" starting mode rsd
I can do twice the iron sbf with 2.3.6 official stock continues to give me the same error.
Lei may be because the battery is not 100% so fails.
How do I charge if the wall charger no load and light me alone with the legend:
"Failde to boot 4" rsd starting mode.
It can be for this, because this is not a 100% Bateias??
Another query may be that by command fastboot mode can be fixed??
As question =) i would like to flash my phone back to stock until ics arrive but i dont know how to do it. Can someone give me a full tutorial?
I m using asia gsm razr xt910, thx
Maybe use this file and flash like you would any Rom?
Well if you find out your ROM region, then you can go download the appropriate ROM in the official ROM thread in the development section and use RSD lite to flash it back to factory ROM. That should work and your phone will be good as new.
http://forum.xda-developers.com/showthread.php?t=1416058
http://forum.xda-developers.com/showthread.php?t=1362956
What is rsd lite and how do i use it? I m noob in this ..
N how do i check my rom region? I m in the arctic now, n when i check my system info, i shows thst my system version is 651.167.20.xt910.retail.en.EU
So what should i do?million thanks to anyone who help me
Ive never done it myself but Im assuming region is the country your living in as some are gsm and some cdma.
On using rsd lite there are several how to with search.
http://www.blogotechblog.com/2011/12/restore-motorola-droid-razr-to-stock-configuration/
Got this from here.
INSTRUCTIONS:
1. If you haven't already done so in the past, download and install the motorola usb drivers.
2. Download and install RSD Lite 5.6.
NOTE: In order for RSD Lite to recognize your phone, it has to be in AP Fastboot mode or it can just be booted up like normal. If your phone will not boot up, then power it off and put it into AP Fastboot mode by holding the volume up + down + power. Then select the AP Fastboot option.
3. Connect your phone to the computer with a usb cable and open RSD Lite. Make sure RSD Lite recognizes your phone before proceeding.
WARNING: Be careful not to move your phone around or mess with the usb cable while doing the following steps. You don't want to accidentally disconnect it. That might end up bad.
4. In RSD Lite, select the fastboot zip file you downloaded then press the "Uncompress and Start Flashing" button. RSD Lite will unzip the file and begin flashing.
5. Once the flashing is done and your phone is booted up, perform a factory reset to complete the process
http://www.razrforums.com/forum/droid-razr-development/775-rsd-lite-fastboot-not-working.html
http://forum.xda-developers.com/showthread.php?t=1486718&highlight=droid+razr+utility
Thanks! Will try that once i free
Do i need to factory reset b4 do this?
omnia1994 said:
Thanks! Will try that once i free
Do i need to factory reset b4 do this?
Click to expand...
Click to collapse
Dont think so because as with my other phones when I restored it automatically wiped the phone.
Ok. Will report once i tried! Many thx for everyone!
Back to stock successfully . Thx!
I followed the steps shown by blueis300
After connecting the device in APFastoot mode I started RSD lite it recognized my device.
Then I selected the zip file and selected the Uncompress and flash option
After Uncompressing the flashing process starts and when it reaches 6/18 it fails.
Please Help!!
any infomation about y it failed?
As soon as it enters step 6 it fails. I have no idea why its failing.
Please Help otherwise i'll be stuck with this stupid ROM
I live in India so is there any problem with the region or something??
r u sure u downloaded the correct rom?
I Got it!!!
So I have been trying a bunch of different roms for the RAZR today and I was having problems with the keyboard not working. I decided to try to load CM9, so I read I need to use "safestrap" and not "bootstrap" that I had been using. I downloaded it, installed then tried to boot into recovery and load CM9.
Now the safestrap boot screen appears and says "safe system disabled" "hit search to continue / hit the menu button to boot into recovery" if I hit the menu button it just reboots, if I hit search the screen just goes blank and I have to do a reset to get it to start the process again.
I have RSD but I have never used it before. I have my phone plugged into my computer but my computer doesnt see it.
Help!
dreamsti said:
So I have been trying a bunch of different roms for the RAZR today and I was having problems with the keyboard not working. I decided to try to load CM9, so I read I need to use "safestrap" and not "bootstrap" that I had been using. I downloaded it, installed then tried to boot into recovery and load CM9.
Now the safestrap boot screen appears and says "safe system disabled" "hit search to continue / hit the menu button to boot into recovery" if I hit the menu button it just reboots, if I hit search the screen just goes blank and I have to do a reset to get it to start the process again.
I have RSD but I have never used it before. I have my phone plugged into my computer but my computer doesnt see it.
Help!
Click to expand...
Click to collapse
Whats your razr. Its verizon? If not you should use bootstrap.
Safestrap is for verizon razr. But some uses bootstrap on it.
You have to put ur razr in ap fastboot mode: power+vol up+vol down in order to flash with rsd lite
Choose a stock rom to your razr and flash it. Make sure flash correct rom
Cheers
Sent from my XT910 using Tapatalk 2
I have the Verizon RAZR.
So my computer does not recognize the phone when in AP Fastboot, but it does recognize it when its in BP SDF flash. What am I doing wrong?
dreamsti said:
I have the Verizon RAZR.
So my computer does not recognize the phone when in AP Fastboot, but it does recognize it when its in BP SDF flash. What am I doing wrong?
Click to expand...
Click to collapse
Uninstall all motorola software, reinstall motocast 1.29 or newer then connect ur razr.
Use rsd lite 5.7 and make sure you got correct sbf file
You may have corrupted drivers.
Cheers
Cheers
Enviado de meu XT910 usando o Tapatalk 2
Do I need to install anything else other than those 2 things? It still doesnt work.
Would having Samsung drivers effect anything? I have a Galaxy Nexus too.
dreamsti said:
Would having Samsung drivers effect anything? I have a Galaxy Nexus too.
Click to expand...
Click to collapse
Sometimes it brokes motorola drivers. Doing what I said should work.
Edit:
BTW what's the version you were and what's the version you're trying to flash?
Some versions cannot downgrade when the one you're trying to flash have a lower security.
I was running Gummy when everything went wrong. Loading safestrap is when I started having the current problems.
I uninstalled the Samsung drivers, and loaded both RSDLite 5.7 and the Moto driver you suggested and RSD will not see my phone in AP Fastboot, but it will when in BP SDF flash. Very confusing.
I will load the latest version of GB when I can get my computer to see my phone in AP Fastboot.
Now my computer is trying to install the flash MZ600 driver and error's out. I googled MZ600 and it says its a Xoom driver???
dreamsti said:
Now my computer is trying to install the flash MZ600 driver and error's out. I googled MZ600 and it says its a Xoom driver???
Click to expand...
Click to collapse
Yup. You've a driver problem, better unistall others devices you may have.
Or, do it in other pc, like a notebook.
So I finally got the drivers working and now RSD see's my phone when in AP Fastboot, but I get an error when flashing the file. This is the error I get.
"Failed flashing process. 22/23 flash "radio.img" -> Phone returned FAIL."
It was flashing for about 5 minutes before I got this error.
Edit: I'm using the file from this thread.
http://rootzwiki.com/topic/13566-droid-razr-fastboot-file/
Blur_Version.6.12.173.XT912.Verizon.en.US
I think the battery went dead, ugh. Ill recharge and report back.
I am having a problem. I was trying to upgrade to Jelly bean 4.1 on this Atrix 4g. I tried to go through the steps that it gave online with the CM10 n Cyro and all. Long story short it couldn't find the rom within the zip or something of that nature. In other words, it screwed me over. I can't get back into recovery. It's been giving me this error:
SVF 108:1:2
Failed to boot 3
Starting RSD mode
Before it was giving me just:
Failed to boot 4
Starting RSD mode
I had tried reseting to factory through the moto-fastboot but of course it failed. I have been tryin like crazy to flash various SBF from 2.3.5 to 2.3.6. I was originally at 2.3.6 but for what ever reason when I try the RSD lite it gives me the error after it executes "Phone did no re-enumerate after RAM downloader was sent". (0x703e). I have been reading forums literally all day. Perhaps I am not understanding something therefore I am missing it but maybe one of you guys could help me out with this? Maybe there is a real simple fix or maybe I completely ruined it? Either way it would be nice to get some help on this. Basically when I was trying to upgrade to 4.1 I followed "How to upgrade the Atrix 4G to Android 4.1.1 Jelly Bean via CyanogenMod 10" off of the androidauthority website. I got to step 9 but it couldn't find the ROM, by then it was too late.
UPDATE: So I got just that and RSD was flashing it until it reached yet another error:
failed flashing process. Failed flashing process. Phone[0000]: error switching phone BP pass through mode (0x70BE); phone disconnected.
Help?
majorrazer said:
Help?
Click to expand...
Click to collapse
I'm no expert, you can wait for an expert response but what i couldnt understand is why you try to flash a SBF. The manual you refer to is a CWM based installation, with a zip file, not a SBF.
So do you have CWM recovery flashed? Do you have the related zip file downloaded to sdcard?
saldirai said:
I'm no expert, you can wait for an expert response but what i couldnt understand is why you try to flash a SBF. The manual you refer to is a CWM based installation, with a zip file, not a SBF.
So do you have CWM recovery flashed? Do you have the related zip file downloaded to sdcard?
Click to expand...
Click to collapse
I don't have anything flashed at the moment. I can't boot into anything at the moment. I am confused perhaps with what will solve my problem.
majorrazer said:
I don't have anything flashed at the moment. I can't boot into anything at the moment. I am confused perhaps with what will solve my problem.
Click to expand...
Click to collapse
Do you have an unlocked bootloader? Does the word "Unlocked" appear when you power the phone on? You must have an unlocked bootloader for sure. IF not, you must unlock it.
his is the guide you were following;
http://www.androidauthority.com/atrix-4g-mb860-android-4-1-1-jelly-bean-cyanogenmod-10-cm10-106639/
As said there, it requires unlocked, rooted Atrix with with ClockworkMod Recovery installed
I guess you can still unlock the bootloader and install cwm recovery. Just search and find instructions.
HEY
i have the same problem also.... and the same error...
is your phone fix already?
could you tell me how?
SVF: 108:failed to boot 3 starting RSD mode
Hi,
I have Atrix 4G AT&T, last night rooted it and from recovery mode install custom rom cm-7.2.0-olympus after reboot its not booted and showing "SVF: 108:failed to boot 3 starting RSD mode". Removing battery also not solve this problem, Andriod recovery mode also not working by pressing down volume key on restarting. RSD Lite procedure also not working for my phone. RSD Lite 5.6 or other versions (i tried most of all) also not deducted my phone when i connected to PC in Fastboot mode. I m new and have not to much information about software version of this Motorola Atrix 4G but before its bricking mode it was on Gingerbread 2.3.6.
I have also tried "cmd prompt" stock frame version and other procedures but all failed to start my Phone to normal.
salimdawar said:
Hi,
I have Atrix 4G AT&T, last night rooted it and from recovery mode install custom rom cm-7.2.0-olympus after reboot its not booted and showing "SVF: 108:failed to boot 3 starting RSD mode". Removing battery also not solve this problem, Andriod recovery mode also not working by pressing down volume key on restarting. RSD Lite procedure also not working for my phone. RSD Lite 5.6 or other versions (i tried most of all) also not deducted my phone when i connected to PC in Fastboot mode. I m new and have not to much information about software version of this Motorola Atrix 4G but before its bricking mode it was on Gingerbread 2.3.6.
I have also tried "cmd prompt" stock frame version and other procedures but all failed to start my Phone to normal.
Click to expand...
Click to collapse
Did you unlock the bootloader the right way?
Sent from my MB860 using xda app-developers app
palmbeach05 said:
Did you unlock the bootloader the right way?
Sent from my MB860 using xda app-developers app
Click to expand...
Click to collapse
Not fully under stand "unlock bootloader" the right way? As mention earlier i m not an expert or more knowledge about Rooting and hacking of Andriod Phones, Please tell me in Details, thanks
salimdawar said:
Not fully under stand "unlock bootloader" the right way? As mention earlier i m not an expert or more knowledge about Rooting and hacking of Andriod Phones, Please tell me in Details, thanks
Click to expand...
Click to collapse
did you flash pudding sbf via rsd and use fastboot to oem unlock?
Sent from my MB860 using xda app-developers app
palmbeach05 said:
did you flash pudding sbf via rsd and use fastboot to oem unlock?
Sent from my MB860 using xda app-developers app
Click to expand...
Click to collapse
No i didnt use RSD methode because RSD Lite not deducting my Phone, tried different versions of RSD for flash pudding, I have Windows 8-64bit.
Also Flash the Mobile throw following procedure
Boot the Atrix into “Fastboot Mode” (hold power + vol down)
plug your Atrix into your PC via USB
Navigate to your fastboot folder via command prompt
type “moto-fastboot flash boot boot.img” press enter
type “moto-fastboot flash system system.img” press enter
type “moto-fastboot -w” press enter
type “moto-fastboot reboot” press enter.
But it also not Boot my phone in normal, Its stuck in Start menu,
SVF 108:1:2
Failed to boot 3
Starting RSD mode
salimdawar said:
No i didnt use RSD methode because RSD Lite not deducting my Phone, tried different versions of RSD for flash pudding, I have Windows 8-64bit.
Also Flash the Mobile throw following procedure
Boot the Atrix into “Fastboot Mode” (hold power + vol down)
plug your Atrix into your PC via USB
Navigate to your fastboot folder via command prompt
type “moto-fastboot flash boot boot.img” press enter
type “moto-fastboot flash system system.img” press enter
type “moto-fastboot -w” press enter
type “moto-fastboot reboot” press enter.
But it also not Boot my phone in normal, Its stuck in Start menu,
SVF 108:1:2
Failed to boot 3
Starting RSD mode
Click to expand...
Click to collapse
ok so its telling you what to do. Since you haven't flashed a sbf, chances are you are not unlocked, so how do you expect to flash anything on a locked device?
Did you install motorola device manager for the drives?
Sent from my MB860 using xda app-developers app
palmbeach05 said:
ok so its telling you what to do. Since you haven't flashed a sbf, chances are you are not unlocked, so how do you expect to flash anything on a locked device?
Did you install motorola device manager for the drives?
Sent from my MB860 using xda app-developers app
Click to expand...
Click to collapse
Yes already install this file from Net
"Motorola_End_User_Driver_Installation_5.1.0_64bit "
and not expect any thing else about flashing of my device.
Before Motorola Atrix 4G, i were used in passed Samsung S1, S2, S3, & T989 (T-Mobile S2 version). All these andriod sets were very easily hack or Root and can install Roms easily .
But Moto Atrix 4G can me upset and sad.
kindly help me to re-connect my self to the andriod world by this Motorola Atrix 4G, thanks
Hey guys I'm having trouble getting to RSS mode my phone comes on then it says entering nv flash recovery mode then the phone dies so I need help trying to get into my phone to flash the sbf file
Sent from my GT-N7105 using XDA Premium 4 mobile app
Need Help regarding Motorola Atrix Mb 861.
salimdawar said:
No i didnt use RSD methode because RSD Lite not deducting my Phone, tried different versions of RSD for flash pudding, I have Windows 8-64bit.
Also Flash the Mobile throw following procedure
Boot the Atrix into “Fastboot Mode” (hold power + vol down)
plug your Atrix into your PC via USB
Navigate to your fastboot folder via command prompt
type “moto-fastboot flash boot boot.img” press enter
type “moto-fastboot flash system system.img” press enter
type “moto-fastboot -w” press enter
type “moto-fastboot reboot” press enter.
But it also not Boot my phone in normal, Its stuck in Start menu,
SVF 108:1:2
Failed to boot 3
Starting RSD mode
Click to expand...
Click to collapse
I need your help regarding Motorola Atrix Mb 861. My phone is not boot and show..
SVF: 108:1:2, Failed to boot 3
Starting RSD mode.
also not able to hard reset. My phone detail are.
My model is KT Atrix MB861
Not sure which is the build number
s/w version: 4.5.2A-KT-75
Android version: 2.3.4
Kernel version: 2.6.32.9-00001...
Please Help regarding that matter.....
kamal.navigator said:
I need your help regarding Motorola Atrix Mb 861. My phone is not boot and show..
SVF: 108:1:2, Failed to boot 3
Starting RSD mode.
also not able to hard reset. My phone detail are.
My model is KT Atrix MB861
Not sure which is the build number
s/w version: 4.5.2A-KT-75
Android version: 2.3.4
Kernel version: 2.6.32.9-00001...
Please Help regarding that matter.....
Click to expand...
Click to collapse
Were you bootloader unlocked before getting this message?
I have the droid razr n was wanting to root it for fun but I don't want to brick it by messing up so I wanted to make sure it was possible for my phone
-spektor- said:
I have the droid razr n was wanting to root it for fun but I don't want to brick it by messing up so I wanted to make sure it was possible for my phone
Click to expand...
Click to collapse
Use safe root:
https://forum.xda-developers.com/attachment.php?attachmentid=2760984&d=1400951117
here video tutorial: http://youtu.be/Eunw58NwFrQ
Dont forget to install drivers first for the device if using windows based pc. After you root use install safe strap 3.75 if your going to be flashing anything or custom roms. Happy rooting.
OGdroidster said:
Use safe root:
https://forum.xda-developers.com/attachment.php?attachmentid=2760984&d=1400951117
here video tutorial:
Dont forget to install drivers first for the device if using windows based pc. After you root use install safe strap 3.75 if your going to be flashing anything or custom roms. Happy rooting.
Click to expand...
Click to collapse
I seemed to have messed up and now it doesn't boot past the Motorola logo it just goes to black screen, while its in the black screen adb is available, I can access fastboot and all but it won't boot up, RSD Lite 6.2.4, i think, doesn't seem to detect my phone is this fixable?
-spektor- said:
I seemed to have messed up and now it doesn't boot past the Motorola logo it just goes to black screen, while its in the black screen adb is available, I can access fastboot and all but it won't boot up, RSD Lite 6.2.4, i think, doesn't seem to detect my phone is this fixable?
Click to expand...
Click to collapse
If you can get to fastboot mode then you should be able to get it going. You will need the drivers installed for your device then you will need the correct stock firmware to flash with rsd lite. When you get to fastboot mode scroll to ap fast boot then tap the volume up button that will take you to the bootloader to flash. Then open up rsd lite. Connect device to your computer. When it reads it click where it shows your device then you should see all information in rsd lite then click start you will get a prompt upon click of start you click decompress and flash button. Just sit back and wait like 10 to 15 minutes. Sometimes it will get stuck at boot logo and rsd lite will say manually reboot phone so go ahead and do so. Once you are in past the bootlogo and actually booted up go ahead and unplug the device from USB port of computer. That's its all done. Here is a side note: when you go into ap fast boot and it says battery is low that means that you will not be able to flash. You will need a fastboot cable. If run into that just let me know I have amazon link where it cost 10 bucks. Cheapest one that's works on our device. I never had a problem with not working.
OGdroidster said:
If you can get to fastboot mode then you should be able to get it going. You will need the drivers installed for your device then you will need the correct stock firmware to flash with rsd lite. When you get to fastboot mode scroll to ap fast boot then tap the volume up button that will take you to the bootloader to flash. Then open up rsd lite. Connect device to your computer. When it reads it click where it shows your device then you should see all information in rsd lite then click start you will get a prompt upon click of start you click decompress and flash button. Just sit back and wait like 10 to 15 minutes. Sometimes it will get stuck at boot logo and rsd lite will say manually reboot phone so go ahead and do so. Once you are in past the bootlogo and actually booted up go ahead and unplug the device from USB port of computer. That's its all done. Here is a side note: when you go into ap fast boot and it says battery is low that means that you will not be able to flash. You will need a fastboot cable. If run into that just let me know I have amazon link where it cost 10 bucks. Cheapest one that's works on our device. I never had a problem with not working.
Click to expand...
Click to collapse
Ah, so if it's low battery it won't connect to rsd lite? I can't tell how charged it is because it doesn't display battery when I plug it in when it's off but I'll charge it for a bit n get back to it.
When you go to fastboot mode then to ap fastboot it will say low if to low to flash otherwise it will say ok