hello my friends
i have galaxy s2 i9100g and whener i try to inter the download mode it says recover with kies
but kies doesnt recognise it
i tried to reflash ics rom and used .bit file but it fails everytime
here is my odin diplay cache
please help me if u can
MY Regards
<ID:0/005> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9100GJPLP6_I9100GOJPLP5_I9100GXXLPR_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Odin v.3 engine (ID:5)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Set PIT file..
<ID:0/005> DO NOT TURN OFF TARGET!!
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> Sbl.bin
<ID:0/005> NAND Write Start!!
<ID:0/005> cache.img
<ID:0/005> factoryfs.img
<ID:0/005>
<ID:0/005> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Advanced search Hopper8's threads to find his 'Odin doesn't flash successfully' thread. There's a bunch of stuff you can try in there.
The only way you're fixing this is if you get the phone to successfully take an Odin flash, unless you want to take it to a service centre where they'll flash the most recent firmware they have to the phone.
Related
I was flashing a firmware from "I9100GZCKH4" to "I9100GDXLP6_I9100GOLBLP6_XME" on my Samsung S II GT-I9100G, and it failed. Now the screen shows "SOFTWARE UPDATE FAIL"
Odin says...
Message
<ID:0/005> Removed!!
<ID:0/005> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9100GDXLP6_I9100GOLBLP6_I9100GDXLP6_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Odin v.3 engine (ID:5)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> cache.img
<ID:0/005> NAND Write Start!!
<ID:0/005> factoryfs.img
<ID:0/005> hidden.img
<ID:0/005> MLO
<ID:0/005>
<ID:0/005> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Happen to me once..make sure KIES not running in background..if u dont know how to check, just uninstall KIES..dont worry, u can get KIES installer later with just google it..
Sent from my GT-I9100G using xda premium
Hello all,
I rooted my galaxy s3 and all went fine, then the battery died (battery is no longer in use) so i bought a new one and all was well, upon flashing stock rom, the write failed.
When booting the phone up it says: "Firmware upgrade encountered an issue. Please select recovery mode in Kies and try again.
<ID:0/005> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
(LONG DELAY HERE)
<OSM> I9305XXBLL5_I9305EVRBLL2_I9305BVBLL2_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Odin v.3 engine (ID:5)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> system.img
<ID:0/005> NAND Write Start!!
<ID:0/005> boot.img
<ID:0/005> cache.img
<ID:0/005> hidden.img
<ID:0/005> recovery.img
<ID:0/005> modem.bin
<ID:0/005>
<ID:0/005> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Any ideas? I need help!
Bad flash wrong firmware or more likely file is corrupt .
Make sure Kies is not running as well .
jje
Im flash on odin this firmware:
I9100XXMS1_I9100OXAMS1_XEO
im have a log from odin.... :
<ID:0/003> Removed!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9100XXMS1_I9100OXAMS1_I9100XXLS8_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Added!!
<ID:0/005> Odin v.3 engine (ID:5)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> boot.bin
<ID:0/005> NAND Write Start!!
<ID:0/005> Sbl.bin
<ID:0/005> param.lfs
<ID:0/005> factoryfs.img
<ID:0/005> __Xmit Write fail
<ID:0/005> XmitData Fail..
<ID:0/005> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
This is now, download mode show me in my pc "Usb device problem...." and, im my phone turn on have message:
Firmware upgrade encountered an issue. Please select recovery mode in kies & try again.
Whats next? im have this phone 1 DAY !!!! :crying:
Hopper8's 'Odin troubleshooting' thread stickied in the General section, find it, try as much of the stuff in the thread as you need to in order to get a successful Odin flash.
Hi
I have the following error when I try to install the correct firmware with odin 3.09
<ID:0/005> hidden.img
<ID:0/005> FAIL!
firmware: sammobile.com I9300XXUGNG3_I9300QXFGNG2_I9300XXUGNA8_HOME.tar.md5
I tried with Kies "Firmware upgrade and initialization "and gave an error at the end and did nothing
I tried another USB cable (original Samsung), another usb port ... same error
I installed TWRP Recovery and when I tried to format partitions data error "not found" I tried to mount but gave "not found" error
full log:
<ID:0/005> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9300XXUGNG3_I9300QXFGNG2_I9300XXUGNA8_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Odin v.3 engine (ID:5)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> SingleDownload.
<ID:0/005> boot.img
<ID:0/005> NAND Write Start!!
<ID:0/005> cache.img
<ID:0/005> hidden.img
<ID:0/005> FAIL!
<ID:0/005>
<ID:0/005> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
what can i do to mek the phone working again?
thank you
Try the rescue firmware and pit, flashed with Odin. Search in general forum for the thread.
Hello, so recently I bought my first samsung device and tried to root my Samsung Galaxy S6 Edge and I was a complete newbie in doing this so then my device keeps saying Recovery Is not Sendroid Enforcing on the start up screen. I Live in Australia and am currently with the carrier Vodafone.
Help PLease
So I tried doing a stock firmware update with a .tar I found somewhere that said it was for the SM-G925I Vodafone Australia so I downloaded I go on Odin Tick Auto Reboot and F. Reset time i then tick AP and select the .tar file it takes a while to check the file then it says leave cs I connect my phone to my pc I then press start and get fail. It says then on my phone SW REV. CHECK FAIL. DEVICE: 3, BINARY: 1
ODIN Script:
<ID:0/005> Removed!!
<ID:0/005> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> G925IDVU1AOC4_G925IVAU1AOC4_G925IDVU1AOC5_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Odin engine v(ID:3.1005)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> SingleDownload.
<ID:0/005> sboot.bin
<ID:0/005> NAND Write Start!!
<ID:0/005> FAIL!
<ID:0/005>
<ID:0/005> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Loquar said:
So I tried doing a stock firmware update with a .tar I found somewhere that said it was for the SM-G925I Vodafone Australia so I downloaded I go on Odin Tick Auto Reboot and F. Reset time i then tick AP and select the .tar file it takes a while to check the file then it says leave cs I connect my phone to my pc I then press start and get fail. It says then on my phone SW REV. CHECK FAIL. DEVICE: 3, BINARY: 1
ODIN Script:
<ID:0/005> Removed!!
<ID:0/005> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> G925IDVU1AOC4_G925IVAU1AOC4_G925IDVU1AOC5_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Odin engine v(ID:3.1005)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> SingleDownload.
<ID:0/005> sboot.bin
<ID:0/005> NAND Write Start!!
<ID:0/005> FAIL!
<ID:0/005>
<ID:0/005> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Click to expand...
Click to collapse
i am having same issues just trying to get my phone back to stock, have tried various different firmwares but just cant get odin to flash...
never had this issue on any previous fones and have been flashing many samsung devices for many years...
but the phone came to me in a bricked state so not sure as have read here that something to do with bootloader, not sure if phone was rooted or what firmware it was on before...
all i would like to do is get it back to stock firmware and running up an normal....
is there a simple way or simple files that i need?