Related
Hello,
Saturday I went out, my HD2 only had like 5% battery life. I used it till it went black. The day after I wanted to recharge my phone but when I plug the microusb in to the wall charger, no led lights come up. When I press the power nothing happens. Stays black, it's like a dead stone now. I did not flash the phone for the past 2 months, it's running android already a long time now.
This morning when I pull the battery out and put it back in and push the power button then a VERY short vibration comes out of the phone but then nothing anymore the screen and leds stay dark. If I try it a second time nothing happens. So I think the battery is 99.9% empty and I can't charge it anymore through the microUSB. The only thing I can think of what happened is saterday I took a bath and my phone was lying on the edge of the bath, it did not fell in the bath offcourse. But there was alot of humidity in the bathroom because of no ventilation and warm water. The phone was working perfectly after the bath and stayed working untill the battery went to 0% when I was going out. Is my microUSB port water damaged? The stickers inside the phone are still white. (luckily). Anyone has an idea how to fix it or what the problem could be?
Remove the battery.
Connect to the power supply.
After a couple of minutes, plug in the battery (while the phone is still connected to the mains supply).
Ok I tried it.
Took battery out. Connected to usb power cable.
Waited +- 5 minutes. Inserted battery -> nothing happens.
Won't turn on, no led lights.
BUT I noticed a strange thing.
If NOT connected to power cable : Take battery out, reinsert. Power on, -> some milliseconds of vibration.
If connected to power cable : Take battery out, reinsert. Power on, -> nothing, no vibration.
So if it is connected to power cable phone acts completely dead when I reinsert battery and push power button. But if it's not connected then when reinserting the battery and I push the power button then a very short vibration is felt.
Weird ... is there something shortcircuiting the phone when connected to powercable??
Ok,
I found someone on my work who has an HD2 like me. So I tried to put a 70% charged battery in my HD2. Guess what ... same result. A little vibration and it stops .
So now I know it is not the battery. It's the phone itself. I've put it now in a bowl of rice and hope next morning it will be magically revived. Maybe when I took a bath saturday there formed some micro water bubbles inside the phone and it still isn't gone by now? I am out of ideas. If this rice thing doesn't work I'll send it to HTC repair centre. They won't notice my hspl because they can't even turn on the phone with a charged battery. I'll guess they'll swap the mobo .. again. My previous repair was because my HD2 was in a constant Carkit mode (also a hardware issue). Sigh
Can you get into Bootloader Mode (Press and hold the Volume Down button, then tap the Power button)?
Nope, it acts like dead meat, even with a charged battery I could try from my friend his hd2. My battery worked in his phone. So it is my phone who is broken.
Think some hardware is busted ... Maybe some circuit is broken ? I just don't know . Now they must repair it for the second time. The first time I got the "phone is always in carkit modus" issue which is also hardware related. I hope they will not make a problem to give me yet another motherboard and yet another IMEI . That will be my 3rd IMEI on this phone then.
Hope they pick it up tomorrow .
K Update to this post.
I've received my HD2 back from HTC repair with a new motherboard / IMEI.
All is working now again .
I am afraid it can happen again . This is my 3th IMEI / mobo now on this phone after owning it a year and 2 months.
They now also didn't put a new "VOID" sticker on the screw
Also no "water detector" anymore.
It seems like they are saying to me, now if the phone breaks again, you have no warranty anymore. It's not my fault the mobo suddenly dies . I doubt it they just "forgot" to put new void stickers on.
Never take cell phone in the bathroom.. especially if its a touchscreen.. the steam from hot water gets accumulated inside the phone and ruins it. My friend damaged his 2 handsets already.. now he doesnt take it in the bathroom anymore
lordraiderke said:
K Update to this post.
I've received my HD2 back from HTC repair with a new motherboard / IMEI.
All is working now again .
I am afraid it can happen again . This is my 3th IMEI / mobo now on this phone after owning it a year and 2 months.
They now also didn't put a new "VOID" sticker on the screw
Also no "water detector" anymore.
It seems like they are saying to me, now if the phone breaks again, you have no warranty anymore. It's not my fault the mobo suddenly dies . I doubt it they just "forgot" to put new void stickers on.
Click to expand...
Click to collapse
There are water dector labels inside the phone and if they forgot the VOID label then that is their problem. You have twice returned the phone and by replacing the motherboard they have admitted that the problem is theirs. So they already have a history of faulty phones from you and since it has been repaired by them, then they would need to show a record of placing a viod label back on the phone.
[The Punisher] said:
Never take cell phone in the bathroom.. especially if its a touchscreen.. the steam from hot water gets accumulated inside the phone and ruins it. My friend damaged his 2 handsets already.. now he doesnt take it in the bathroom anymore
Click to expand...
Click to collapse
Well I also think that was the cause the phone died later that evening.
I think the phone went dead sometime that night because of the water inside the phone. Luckily the water detection labels where still white .
I never will let it inside the bathroom again .
As for the void sticker problem, I will contact them to ask why they didn't put on new stickers. If they don't respond I saw you can buy such stickers on ebay .
Hey guys. on saturday night. the hero my gf had was dropped into a toilet.
i managed to get it back the following day
and ive head it in a bag or rice ever since then
i took it out this morning to have a look and i tried power button and nothing happened.
i plgged it into usb to see what was up and the charge light came on. however when i press the power button the charge light goes off and the phone does nothing
ive included pictures of the phone below.
PICS
what are recomendations
I'm anything but an expert, but it's likely the water has got into the screen area and other parts and possibly short circuited it?
Hi,
So as the title say, my battery act very weird.
At first, it refused to charge through the charger. Took out battery and waited 10 min, then it charge, until 100%, unplug charger, and it still charging , never stop.
Took out battery again, waited 10 min, put it in, battery charging icon appear on screen with the little yellow triangle inside, cannot turn on phone. Then I plug charger in, now I can turn on the phone, but battery level now show 80% and notification : charging paused, voltage too high.
Could someone help me?
Thanks
P/s: It was happened last night, leave it over night and I can use the phone normally this morning though.
Saisuay said:
Hi,
So as the title say, my battery act very weird.
At first, it refused to charge through the charger. Took out battery and waited 10 min, then it charge, until 100%, unplug charger, and it still charging , never stop.
Took out battery again, waited 10 min, put it in, battery charging icon appear on screen with the little yellow triangle inside, cannot turn on phone. Then I plug charger in, now I can turn on the phone, but battery level now show 80% and notification : charging paused, voltage too high.
Could someone help me?
Thanks
P/s: It was happened last night, leave it over night and I can use the phone normally this morning though.
Click to expand...
Click to collapse
Oh. Good. Lord.
10 min is NOT ENOUGH TIME to let the thing dry after you dropped the whole thing into water. You probably screwed the pooch on this one.
If the phone is dropped in water, most people recommend taking the phone apart and putting all pieces into a bag full of uncooked rice and silica packages for at least a few (preferably up to 5) DAYS before attempting to reconnect battery.
Because you've reattached battery already after less than 1 hour TWICE, I'm betting you have shorted your mainboard beyond all repair.
Water + electronics isn't necessarily the kill factor. Water + electronics + electrical current (connected battery) BEFORE DRY = dead electronics.
You should leave the battery out of the SGS and put both in a bag with much rice or cat litter some days in a bag. No hair dryer or something like this.
It wasn't a good idea to connect the loader and to leave the battery in the mobile.
I have a friend with exactly the same problem, his daughter put the GS2 phone into water and then he put the battery out for ONE night only... now the phone says is charging when it's unplugged and sometimes the "car mode" activates by his own (i don't even know how to activate the car mode on my GS2) ....
we started to think that the problem will stay forever
alexpardox said:
I have a friend with exactly the same problem, his daughter put the GS2 phone into water and then he put the battery out for ONE night only... now the phone says is charging when it's unplugged and sometimes the "car mode" activates by his own (i don't even know how to activate the car mode on my GS2) ....
we started to think that the problem will stay forever
Click to expand...
Click to collapse
And now that the battery was put back into the phone after only one night, it probably will.
mine too fell in luke warm water but i removed batt in all covers open ,kept in a rice bag for jus 2,3hrs an the i blowd hair dryer the kool one not hot air.....an now my phone is good .....atleast now don charge an remove ,keep it to dry an check out if ur lucky ,it will work or ,the service center m8.
rocky23 said:
mine too fell in luke warm water but i removed batt in all covers open ,kept in a rice bag for jus 2,3hrs an the i blowd hair dryer the kool one not hot air.....an now my phone is good .....atleast now don charge an remove ,keep it to dry an check out if ur lucky ,it will work or ,the service center m8.
Click to expand...
Click to collapse
You got lucky if yours isn't showing any ill effects after such a short dry time. Yours is an exception.
ometimes the "car mode" activates by his own (i don't even know how to activate the car mode on my GS2) ....
Click to expand...
Click to collapse
Well, i did have the same selfactivates problem like you for few min,It even turn it on after i put the battery in, without any action. But it gone now. The problem is that it keep saying charging and the notification keep pop up. I can overcome it by install AOKP or CM9 Rom which dont have that kind of notification. But still, my concern is how long can it take till it really dead?...
You got lucky if yours isn't showing any ill effects after such a short dry time. Yours is an exception.
Click to expand...
Click to collapse
we started to think that the problem will stay forever And now that the battery was put back into the phone after only one night, it probably will.
Click to expand...
Click to collapse
Start looking for a new phone now.
If you already shorted it, it's not going to go away. Electronics don't just heal themselves over time.
A repair shop may be able to replace parts with shorted components, but if many have shorts, it may not be worth it to fix, and may end up being more expensive to fix than to replace.
You should have left the phone to dry atleast for a solid 24 hours in a rice bag!
I put my old Sony Ericsson in the washing machine once (was in a pair of shorts) lol.
Of course I don't expect it to work... but I opened it up and took out battery etc... left it out to dry in the sun for few minutes (making sure it doesn't get too hot), then put in a nice dry place with dehumidifier. After a couple of days it worked again.
Now that is just lucky and it probably wouldn't last for long... but luckily I was going to buy a new phone at the time anyways.
Moral of the story... phones, or any electronics, are not waterproof unless stated that they are. You have to be more careful people... or get something like Invisible Shield.
do you think that the problem will go away if I got a new battery ??
alexpardox said:
do you think that the problem will go away if I got a new battery ??
Click to expand...
Click to collapse
How can you be confused about this? The issue is a short on one of the electronic components in the phone. Probably the mainboard. Getting a new battery won't address that.
Why not bring it in to some service center (or even some night market telephone tech guys) and have them check it out? Then they can tell you what needs replacing or if you're better off getting a new phone.
This was my question before I converted it into a tutorial:
Sorry if this question was posted before (I did ask this in the NOOB-FRIENDLY thread, but didn't get a constructive answer)
My Xperia Neo V dropped into water.
Dried it with rice for a whole day and turned it on. Success! Was able to even play games.
Then I sent it for charging. (Battery was 8%)
5 mins later, it died.
Responds by entering flashmode after blinking red LEDs (3 I think), so I flashed stock.
Still couldn't start, so I sent it for charging (No response either after some hours)
I abandoned it and switched to a Galaxy Ace...until now....
Connected it to PC a month later.
It blinks red LED continuously, unplugged it and plugged it to a charger. No LED response whatsoever.
Plugged to PC again and POOF! Magic.
Detected by PC as my old MT11i :'D
LED is green, can do file exploration. Buttons are lit, vibrates when I press shutter button. No sound with the volume buttons
So the verdict...
CAN I STILL REVIVE MY NEO V?
IS MY DISPLAY DAMAGED?
This tutorial was made possible by @xange and @georgeiulian89. Thanks!
Usually when you drop your phone, you would be doomed. Or so you thought. With this tutorial, you can save A LOT of money buying a new phone or repairing the wet phone!
HOWEVER, I CANNOT GUARANTEE THAT YOUR PHONE CAN REVIVE. THIS WORKED FOR ME (SHALLOW DIP IN WATER). YOU MIGHT ALSO NEED A NEW BATTERY (IF YOU THINK YOU CAN REVIVE IT)
Steps(suggested by xange, proved):
1. Remove your phone from the water source IMMEDIATELY! (duh) DO NOT ATTEMPT TO SWITCH IT ON OR PRESS ANY BUTTON.
2.Remove the battery, SIM and micro SD cards.
3.Dry the body with a dry cloth. Try not to use tissue paper as it will leave residue.
4.Disassemble the phone, all the way to the motherboard. I used a small slotted screwdriver (the one with only one edge)as there are screws shaped like stars. If you have that type of screwdriver you can use it. Similar disassembly video here: www.youtube.com/watch?v=ginuDIeNCs8
WARNING: INTERNAL PARTS ARE VERY SENSITIVE TO STATIC, METAL,ETC. BE CAREFUL. ALSO REMOVE THE CONNECTIONS TO THE FRONT COVER AND DIGITIZER (display) BEFORE REMOVING THEM.
5.Direct a blowing fan to all the internal parts to dry them. Keep the screws and parts in an accessible area. Leave it for 30 minutes. DO NOT DRY IT WITH A HAIRDRYER. YOU ARE JUST TRYING TO SCREW YOUR PHONE.
6.Reassemble the phone and insert the battery ONLY. NOTE: Make sure the ribbon connector is clean before connected, if dust (or any tiny electric conductor) sticks on the connector while connecting them, you will have high chancesof damaging the phone. Then, switch on the phone. If not,
A) CHARGE IT: Your phone battery might be 100% dead(until normal charging can't power it on). For me I pressed and held the Back button while plugging the charger into the phone (Flashmode). The LED should blink red and eventually, green. This is when normal charging starts.
B) REPLACE THE BATTERY: You'll need to do so especially when the (once)white area near the connectors of the battery has turned red, indicating battery damage.
C) SEND IT TO A (optional: AUTHORIZED) SERVICE CENTER: Out of luck. This is the furthest I can help.
ALTERNATIVE DRYING METHODS:
A)PUT IT IN RICE FOR A DAY: NO, Asians won't come to repair your phone. Rice acts like silica, which absorbs moisture like sponge. I suggest you disassemble the phone first as rice might get into the small holes around your phone.
B)SOAK IN ALCOHOL, THEN PUT IT OUT: Disassemble it first, too. Though I haven't tried this method, there are those who have proved it to work.
C) RADIATOR DRYING (suggested by georgeiulian89): I've turned it off,i've removed the back cover, took out the battery, sim card and sd card, and i've put the phone on the radiator (i've put a towel between the phone and the radiator and i've placed the phone on the towel). I've left the phone about two hours to dry, and then i've inserted back the sim, sd card and the battery and turned it on.
C)DRY IT WITH A HAIRDRYER: NO. RISKY METHOD. Water will evaporate, then condense back somewhere once you've done hairdrying your phone it will condense back. I tried it and it condensed on my phone's camera lens. (It's a hairdryer, not a phonedryer!)
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Hope this tutorial helps those out there whose phones have went swimming (or diving)
THANK ME IF I HELPED
Jessss
Sent from my Xperia Neo V using XDA Premium 4 mobile app
karanrajkapur said:
Jessss
Sent from my Xperia Neo V using XDA Premium 4 mobile app
Click to expand...
Click to collapse
If you mean yes, then HOW?
fenzo3 said:
If you mean yes, then HOW?
Click to expand...
Click to collapse
What i believe is you've broken your battery and i didn't get anything what you asking about the display. It doesn't light up or what???
Sent from my Xperia Neo V using XDA Premium 4 mobile app
I dropped my Xperia Neo into water for 3 times, yet still operable, i mean, it survived 3 times of dropped into a pail of water, NO JOKES! .
What you should do is, the moment you dropped your phone into water, pick it out of water immediately, open the back cover and take out the battery immediately to prevent further electric short circuit. You will need some small tool to open every single screw to get the mother board come out (careful when unplug those ribbon sockets, if it breaks, you may have to pay to replace it) and dry (using hair dryer?) every single spot in the phone, except the screen, the screen should be tightly seal and should have no water enter into it. maybe the rubber physical buttons you have to take out and dry it too. (DON'T open the screen no matter what happen, unless water really enters the screen, or else the dust enter and stick at the screen you will have a REALLY HARD TIME { i mean it } to clean those dust out of the screen) confirm everything is dried and then assemble it. (from here onwards, it is a luck test whether you still able to save your phone or not, a line between hell and heaven) Put in your battery, It is normal you may not able to turn on your phone at first, give it a charge about 20 minutes and leave it there (red LED may blink repeat-ly for a while and you will not able to turn it on, just leave it) then switch it on, If you still can't turn it on, try change the battery. If symptom persist, god bless you, i tried my best helping you. ( it means it may not 100% probability to save your phone, but it is a way i did to save my phone)
Eventhough my phone survived dropping into water for 3 times, but it has some problems now, a random one, the phones get really really hot for no reasons for a short period (about 1 hour to 2 days) the heat comes from the motherboard after my inspection, maybe some water droplet enter into the chips and causing electric short circuit?
Good luck.
xange said:
I dropped my Xperia Neo into water for 3 times, yet still operable, i mean, it survived 3 times of dropped into a pail of water, NO JOKES! .
What you should do is, the moment you dropped your phone into water, pick it out of water immediately, open the back cover and take out the battery immediately to prevent further electric short circuit. You will need some small tool to open every single screw to get the mother board come out (careful when unplug those ribbon sockets, if it breaks, you may have to pay to replace it) and dry (using hair dryer?) every single spot in the phone, except the screen, the screen should be tightly seal and should have no water enter into it. maybe the rubber physical buttons you have to take out and dry it too. (DON'T open the screen no matter what happen, unless water really enters the screen, or else the dust enter and stick at the screen you will have a REALLY HARD TIME { i mean it } to clean those dust out of the screen) confirm everything is dried and then assemble it. (from here onwards, it is a luck test whether you still able to save your phone or not, a line between hell and heaven) Put in your battery, It is normal you may not able to turn on your phone at first, give it a charge about 20 minutes and leave it there (red LED may blink repeat-ly for a while and you will not able to turn it on, just leave it) then switch it on, If you still can't turn it on, try change the battery. If symptom persist, god bless you, i tried my best helping you. ( it means it may not 100% probability to save your phone, but it is a way i did to save my phone)
Eventhough my phone survived dropping into water for 3 times, but it has some problems now, a random one, the phones get really really hot for no reasons for a short period (about 1 hour to 2 days) the heat comes from the motherboard after my inspection, maybe some water droplet enter into the chips and causing electric short circuit?
Good luck.
Click to expand...
Click to collapse
I followed a disassembly video for the Neo, but unfortunately the Neo V has a slightly different assembly, so I could not remove the screen to get access to the motherboard. Also, before I put it in rice, I tried to turn it on (Sony said it was water-resistant) after 12 hours in rice. The screen went all weird but I could hint the LegacyXperia kernel logo. That was before my phone booted up normally, and died upon charging.
For your heat problem, perhaps rust? Water should have evaporated from the heat and condensed everywhere in the motherboard.
Would soaking it in alcohol help?
fenzo3 said:
Sorry if this question was posted before (I did ask this in the NOOB-FRIENDLY thread, but didn't get a constructive answer)
My Xperia Neo V dropped into water.
Dried it with rice for a whole day and turned it on. Success! Was able to even play games.
Then I sent it for charging. (Battery was 8%)
5 mins later, it died.
Responds by entering flashmode after blinking red LEDs (3 I think), so I flashed stock.
Still couldn't start, so I sent it for charging (No response either after some hours)
I abandoned it and switched to a Galaxy Ace...until now....
Connected it to PC a month later.
It blinks red LED continuously, unplugged it and plugged it to a charger. No LED response whatsoever.
Plugged to PC again and POOF! Magic.
Detected by PC as my old MT11i :'D
LED is green, can do file exploration. Buttons are lit, vibrates when I press shutter button. No sound with the volume buttons
So the verdict...
CAN I STILL REVIVE MY NEO V?
IS MY DISPLAY DAMAGED?
Click to expand...
Click to collapse
I guess that it's a problem with the battery, not with the display (probably the battery has been short-circuited). I dropped my phone (Xperia Neo) in water 3 days ago. I've took it out after about 10-15 seconds (this was the time until i've realised that it dropped). The phone was still working fine, it didn't shut down by itself. What i did: I've turned it off,i've removed the back cover, took out the battery, sim card and sd card, and i've put the phone on the radiator (i've put a towel between the phone and the radiator and i've placed the phone on the towel). I've left the phone about two hours to dry, and then i've inserted back the sim, sd card and the battery and turned it on. Gues what: it works without any problem, just like before the incident. You should check the water damage indicator on the battery (it's a white strip near the connectors of the battery). If it's white, the phone don't have any problem, but if it's pink or red, the phone was damaged by the water. Mine it's white, with some very little pink on the edge (before it was completely white).
georgeiulian89 said:
I guess that it's a problem with the battery, not with the display (probably the battery has been short-circuited). I dropped my phone (Xperia Neo) in water 3 days ago. I've took it out after about 10-15 seconds (this was the time until i've realised that it dropped). The phone was still working fine, it didn't shut down by itself. What i did: I've turned it off,i've removed the back cover, took out the battery, sim card and sd card, and i've put the phone on the radiator (i've put a towel between the phone and the radiator and i've placed the phone on the towel). I've left the phone about two hours to dry, and then i've inserted back the sim, sd card and the battery and turned it on. Gues what: it works without any problem, just like before the incident. You should check the water damage indicator on the battery (it's a white strip near the connectors of the battery). If it's white, the phone don't have any problem, but if it's pink or red, the phone was damaged by the water. Mine it's white, with some very little pink on the edge (before it was completely white).
Click to expand...
Click to collapse
Thanks for the tip but in all-summer Singapore we don't have radiators.
UPDATE: After following steps by @xange to reassemble and charge my Neo V, it BEAUTIFULLY WORKED!
The catch: Battery calibration problem, stuck at 100%. I'll figure a way out. Thanks a lot devs!
fenzo3 said:
Thanks for the tip but in all-summer Singapore we don't have radiators.
UPDATE: After following steps by @xange to reassemble and charge my Neo V, it BEAUTIFULLY WORKED!
The catch: Battery calibration problem, stuck at 100%. I'll figure a way out. Thanks a lot devs!
Click to expand...
Click to collapse
To get rid of 100% battery issue, you might just want to flash stock ftf in the first place, give it a full charge and then flash your desired driver.
Sent from my Xperia Neo V using XDA Premium 4 mobile app
fenzo3 said:
Thanks for the tip but in all-summer Singapore we don't have radiators.
UPDATE: After following steps by @xange to reassemble and charge my Neo V, it BEAUTIFULLY WORKED!
The catch: Battery calibration problem, stuck at 100%. I'll figure a way out. Thanks a lot devs!
Click to expand...
Click to collapse
try battery calibrator by zeppelinrox. i couldn't recall where he put the script. try search around XDA.... good luck.
---------- Post added at 09:26 PM ---------- Previous post was at 09:16 PM ----------
fenzo3 said:
This was my question before I converted it into a tutorial:
Sorry if this question was posted before (I did ask this in the NOOB-FRIENDLY thread, but didn't get a constructive answer)
My Xperia Neo V dropped into water.
Dried it with rice for a whole day and turned it on. Success! Was able to even play games.
Then I sent it for charging. (Battery was 8%)
5 mins later, it died.
Responds by entering flashmode after blinking red LEDs (3 I think), so I flashed stock.
Still couldn't start, so I sent it for charging (No response either after some hours)
I abandoned it and switched to a Galaxy Ace...until now....
Connected it to PC a month later.
It blinks red LED continuously, unplugged it and plugged it to a charger. No LED response whatsoever.
Plugged to PC again and POOF! Magic.
Detected by PC as my old MT11i :'D
LED is green, can do file exploration. Buttons are lit, vibrates when I press shutter button. No sound with the volume buttons
So the verdict...
CAN I STILL REVIVE MY NEO V?
IS MY DISPLAY DAMAGED?
This tutorial was made possible by @xange and @georgeiulian89. Thanks!
Usually when you drop your phone, you would be doomed. Or so you thought. With this tutorial, you can save A LOT of money buying a new phone or repairing the wet phone!
HOWEVER, I CANNOT GUARANTEE THAT YOUR PHONE CAN REVIVE. THIS WORKED FOR ME (SHALLOW DIP IN WATER). YOU MIGHT ALSO NEED A NEW BATTERY (IF YOU THINK YOU CAN REVIVE IT)
Steps(suggested by xange, proved):
1. Remove your phone from the water source IMMEDIATELY! (duh) DO NOT ATTEMPT TO SWITCH IT ON OR PRESS ANY BUTTON.
2.Remove the battery, SIM and micro SD cards.
3.Dry the body with a dry cloth. Try not to use tissue paper as it will leave residue.
4.Disassemble the phone, all the way to the motherboard. I used a small slotted screwdriver (the one with only one edge)as there are screws shaped like stars. If you have that type of screwdriver you can use it. Similar disassembly video here: www.youtube.com/watch?v=ginuDIeNCs8
WARNING: INTERNAL PARTS ARE VERY SENSITIVE TO STATIC, METAL,ETC. BE CAREFUL. ALSO REMOVE THE CONNECTIONS TO THE FRONT COVER AND DIGITIZER (display) BEFORE REMOVING THEM.
5.Direct a blowing fan to all the internal parts to dry them. Keep the screws and parts in an accessible area. Leave it for 30 minutes. DO NOT DRY IT WITH A HAIRDRYER. YOU ARE JUST TRYING TO SCREW YOUR PHONE.
6.Reassemble the phone and insert the battery ONLY. Then, switch on the phone. If not,
A) CHARGE IT: Your phone battery might be 100% dead(until normal charging can't power it on). For me I pressed and held the Back button while plugging the charger into the phone (Flashmode). The LED should blink red and eventually, green. This is when normal charging starts.
B) REPLACE THE BATTERY: You'll need to do so especially when the (once)white area near the connectors of the battery has turned red, indicating battery damage.
C) SEND IT TO A (optional: AUTHORIZED) SERVICE CENTER: Out of luck. This is the furthest I can help.
ALTERNATIVE DRYING METHODS:
A)PUT IT IN RICE FOR A DAY: NO, Asians won't come to repair your phone. Rice acts like silica, which absorbs moisture like sponge. I suggest you disassemble the phone first as rice might get into the small holes around your phone.
B)SOAK IN ALCOHOL, THEN PUT IT OUT: Disassemble it first, too. Though I haven't tried this method, there are those who have proved it to work.
C) RADIATOR DRYING (suggested by georgeiulian89): I've turned it off,i've removed the back cover, took out the battery, sim card and sd card, and i've put the phone on the radiator (i've put a towel between the phone and the radiator and i've placed the phone on the towel). I've left the phone about two hours to dry, and then i've inserted back the sim, sd card and the battery and turned it on.
C)DRY IT WITH A HAIRDRYER: NO. RISKY METHOD. Water will evaporate, then condense back somewhere once you've done hairdrying your phone it will condense back. I tried it and it condensed on my phone's camera lens. (It's a hairdryer, not a phonedryer!)
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Hope this tutorial helps those out there whose phones have went swimming (or diving)
THANK ME IF I HELPED
Click to expand...
Click to collapse
add in: make sure the ribbon connector is clean before connected, if dust(or any tiny electric conductor) stick at connector while connecting them, you will have high chances to spoilt the phone.
Hi there, XDA folks!
Mario here with some phone problems..
I have a CDMA Evo 3D running on the stock ROM.
The phone's charging cable was shorting out ever since I bought it (got it 2nd hand). I had to wiggle it in order to get the phone charging.
I gave it to my girlfriend to use it for taking pictures n whatnot while outside of town. She returned it kinda Rambo-ish; the front of the phone basically fell apart.. the front metal grill surrounding it, at least.
Phone worked fine, except for the cable shorting out even more. My laptop shut down every time that happened, so I'm quite sure that's not what caused the problem I'll be explaining later on in this thread.
So let's get to the point, shall we?
My phone was really low on battery, something within the range of 2-5%. I tried charging it, but the wires shorted out again and the laptop died on me.. again, and again, and again..
I couldn't really bother with fiddling around with it until it starts, so I just unplugged it and left it that way.
The phone sat for a few days, my (main) laptop broke, so I decided to give the good ol' Facebook Messenger a go.. sadly, the phone would not turn on or start charging.
I removed the shrink-like wrap around the wires of the USB cable, cut the bad parts and twisted the color-matching wires in order. Sadly, the phone would still not charge.
I tried with another (self-made) USB cable... no luck whatsoever. Just to clarify; the blue wire on the one the phone comes with is ground, right? If not that could of caused the problem, since I connected the blue wire on the mini-usb to the black one on a standard USB plug.
I tried juicing the phone up a tad bit by running 5V on the battery for 15 minutes or so.. didn't really bother going for more, since it's kinda hard to keep 2 wires pressed against the battery for more than that. The phone powered up, but the display did not. There was the low battery sound, volume keys were functional, vibrating feedback was okay.. hell, the phone even took a screenshot when I pressed power button + volume down!
Sadly, that didn't solve anything.. even turned on, it would not charge. The 15-minute charge is good for a minute of red blinking light and fancy glowing buttons, nothing more.
Is the phone dead, or should I give it a hour charge directly and see how that goes?
Thanks in advance to everyone who replies!
i think it'll be good if you buy a universal battery charger for phone. so you can charge your battery without plugged to the phone
apinghed said:
i think it'll be good if you buy a universal battery charger for phone. so you can charge your battery without plugged to the phone
Click to expand...
Click to collapse
I am looking for more opinions before I spend cash I don't have on chargers that may not work.
If you or someone else is positive about the display not working because of not enough battery juice, then I'll manually charge the battery for an hour, even though it's uncomfortable as hell to hold 2 wires on the pins for that long.
What's bugging me is that it's not charging once it has just enough juice to power up everything, no display either. I'd like to know if it's doing that, because the battery is too dead to actually start charging up via the phone and whether the display just doesn't work or there's not enough juice for it.
Edit; I bought a chinese charger that charges the battery directly (2pins). The display still does not work and the phone will still not charge via the cable. Could it be a bad cable (and a dead display..)? It seems like the phone itself is responsive - I unlock it, press the "search" button and when I type on the keyboard (that I don't see), it vibrates with every pressed key.
Also, I can hear it taking a screenshot and the volume down/up buttons seem to be working fine.
Dontrememberusername said:
Edit; I bought a chinese charger that charges the battery directly (2pins). The display still does not work and the phone will still not charge via the cable. Could it be a bad cable (and a dead display..)? It seems like the phone itself is responsive - I unlock it, press the "search" button and when I type on the keyboard (that I don't see), it vibrates with every pressed key.
Also, I can hear it taking a screenshot and the volume down/up buttons seem to be working fine.
Click to expand...
Click to collapse
this is exactly what's been going on with my phone as of a few days ago.
checked the time while it was plugged in, unplugged it...screen froze.
hasn't turned back on since.
the buttons on bottom light up, though.
i can take calls, use my unlock pattern (it takes me a few tries now that i can't see anything) and press the search key for google now.
for all intents and purposes...phone's fully functional...except i can't see anything going on.
i brought my phone into a sprint corp store, they changed the top housing for me screen and all for free.
it was really nice.
but, that didn't change anything.
screen still doesn't change anything.
they said the board probably shorted on screen lead.
have you figured anything out?
cipher77 said:
this is exactly what's been going on with my phone as of a few days ago.
checked the time while it was plugged in, unplugged it...screen froze.
hasn't turned back on since.
the buttons on bottom light up, though.
i can take calls, use my unlock pattern (it takes me a few tries now that i can't see anything) and press the search key for google now.
for all intents and purposes...phone's fully functional...except i can't see anything going on.
i brought my phone into a sprint corp store, they changed the top housing for me screen and all for free.
it was really nice.
but, that didn't change anything.
screen still doesn't change anything.
they said the board probably shorted on screen lead.
have you figured anything out?
Click to expand...
Click to collapse
Nope, I'm still in the same situation.
Does yours charge?
My phone isn't recognized by my laptop at all, so I'm guessing something is indeed fried. I don't have the appropriate screwdrivers to open it up and inspect the board, otherwise I'd open it up and check it out.
If you have Torx T5 & T3 screwdrivers you should give it a go - post some decent-res pics over here and I'll at least visually inspect it.
I genuinely don't feel like spending more money for tools n whatnot for a phone that may be permanently dead.. planning on getting a second-hand S4 anyways. Waiting on a student loan and smashing this phone to pieces as soon as I get the cash for a new one. Can try and help out for yours if you manage to open it, though. Could be something as simple as a dead resistor that shouldn't be too hard to replace.
I tried the hillbilly method and hit my phone a few times against a wooden bench, that didn't seem to fix it. Pretty positive something's fried, but I'm also guessing it isn't a viable component, having in mind the phone functions normally, even though the display & usb port don't work.. hell, my phone woke me up at 3AM today, 'cause the alarm went off, lol!