Hi, when i try to unlock my bootloader i've got this message in execute mode of Windows :
INFO[ERR] Command error!!!
OKAY[0.012s] finished. total time 0.012s
Do i need to upgrade the hboot cause i don't know how.
Thanks for replies! I'm stuck!
I'm on Jelly Bean 4.1 STOCK Version of course.
Up please, i can't install full sense rom and i'm stuck now since a week
You must be doing something wrong. Follow the instructions again carefully.
At which command do you get the error?
i think your unlock code might be incorrect. Get it again from htcdev
I've put the three files in C/ root and in Windows command i choose it. But when i enter thé next command given by HTC i have the error. I followed every steps carrzfully
Check whether you're using USB3.0.
It should work on USB2.0
ur command is wrong
USB 3.0 was the problem! Now it worked like a charm!! Thanks!
Related
I don't know why I use HTC_Uni_SIM_Unlock_v1 with my phone !!!!
Now I can,t use IT. During the boot stops same seconds after the windowsmobile screen. It's impossible to contact it.
Read "Problem 5: Device shows NO GSM when booting" on the Common Upgrading Problems in HTC Hermes" wiki page. Solution is there for you
Maybe we should post a warning along with the Universal SIM Unlock tool instructions... such as
DON'T EVEN THINK ABOUT USING THIS WITH A HERMES!!!!!!!
There seems to be at least a couple of new victims every week!
I follow solution n°5 but I have a broblem with the bootloader. The Buttons are correct ?
Thanks
domomedia5 said:
I follow solution n°5 but I have a broblem with the bootloader. The Buttons are correct ?
Click to expand...
Click to collapse
Yes: SIDE OK + POWER + STYLUS RESET
I not be able to connect via USB the phone ! The radio rom 1.20.31.10 don't recognize my phone
http://wiki.xda-developers.com/index.php?pagename=Hermes_ExtractedRadioRoms
is this the correct rom
thanks
Yes, this is the correct rom:
If you get a "ERROR 120: COUNTRY ID ERROR", do not disconnect the device, run MaUpgradeUt_noID again.
when I arrive to the window from ver. to ver. there are no description of the version !
what can I do
No problem, this is normal it is because the device is in bootloader mode.
how many minutes I had to wait
no more than 30min
It's stop from 30 minutes on cheching information on your device !?!?!
If the Hermes screen shows "Upgrade Radio Stack Please wait........." just wait until it finishes, if not, reset your device and put it back in bootloader mode, and run MaUpgradeUt_NoID again.
Make sure you've previously run the 'erase' commands in mtty sucessfully:
http://wiki.xda-developers.com/index.php?pagename=Hermes_UpgradeProblems
If you can not success with radio upgrade, do a full rom upgrade using a rom matching your CID, start the upgrade from bootloader and make sure usb connections in activesync is disabled.
I have tried many times to upgrade the Rom Image on my HTC Tytn (Cingular 8525) with no success. I am getting a 260 error with the program located at this link...
http://forum.xda-developers.com/showthread.php?t=293665
I did first run the unlocking application to unlock both SIM and CID before running the upgrade.
I followed all the steps exactly and have had no success...
The following might be effecting my attempt:
I am running my pc on Vista
I am syncing with Windows Mobile Device Center
I have tried to solve this problem for about two weeks. Can anyone help me?
Mrvanx has a guide on how to prepare Vista for flashing, you can find it here.
This information still did not work. I get a 260 error even after updating the driver, which I did not do until now.
After investigating furthur I have realized what the error is:
As soon as the RUU says "Verifying Information on your PDA Phone..." the second time and forces the device to enter bootloader, the usb connection is lost between the device and the pc. Investigating furthur, the connection to my tytn is lost every time I enter bootloader, whether it is by Power+OK+SoftReset or forced by RUU. Does anyone know how to fix this bootloader connection problem?
Same problem
compwiz2008 said:
This information still did not work. I get a 260 error even after updating the driver, which I did not do until now.
After investigating furthur I have realized what the error is:
As soon as the RUU says "Verifying Information on your PDA Phone..." the second time and forces the device to enter bootloader, the usb connection is lost between the device and the pc. Investigating furthur, the connection to my tytn is lost every time I enter bootloader, whether it is by Power+OK+SoftReset or forced by RUU. Does anyone know how to fix this bootloader connection problem?
Click to expand...
Click to collapse
Same problem here trying to change the radio version after changing the bootloader........
Connection alwayse lost just as said above.
Any help will be appreciuated
justx24
Use the RUU wrapper with the NBH file you want to upgrade.
I still have the same issue, even when using the RUU Wrapper and any nhb.
don't use vista
Ok, got one step furthur
I reached the point where the ROM Begins to update, which is VERY good...
The ROM update Reaches 1%, then waits for 20 minutes...
Then I get a 262 error and have to go through recovery, try again, with the same result.
i have same problem plz help thnx in advance
compwiz2008 said:
This information still did not work. I get a 260 error even after updating the driver, which I did not do until now.
After investigating furthur I have realized what the error is:
As soon as the RUU says "Verifying Information on your PDA Phone..." the second time and forces the device to enter bootloader, the usb connection is lost between the device and the pc. Investigating furthur, the connection to my tytn is lost every time I enter bootloader, whether it is by Power+OK+SoftReset or forced by RUU. Does anyone know how to fix this bootloader connection problem?
Click to expand...
Click to collapse
Have you tried removing or adding a checkmark to the USB to PC in CONNECTIONS on your device? I remember having a similar problem when I installed Radio Rom 1.38 that my USB connection was lost with the pc . I am using XP when flashing so if you have no luck then do this on a XP machine.
Forgot to ask! What ROM are you trying to flash??
@compwiz2008 and ahmerpar
I read somewhere that running windows update will update WMDC........maybe give that a shot?
Maybe you can try to upgrade your ROM from your SD card.
Nope
Let me try that...
Still did not work
I'm probably going to just take my phone to a computer repair shop and pay them to deal with it, since I'm evedently doing something wrong.
Just bought this phone on an internet auction and tried to update it to wm 6.1, but when I enter to bootloader, it goes 2%, 4% and then it just turns off and I get this error message on my PC saying "Error [270] - update error". Tried 2 different roms, same thing happened, even tried hardSPL, also got the same error. Any ideas how to avoid this problem? Thanks in advance.
aco036 said:
Just bought this phone on an internet auction and tried to update it to wm 6.1, but when I enter to bootloader, it goes 2%, 4% and then it just turns off and I get this error message on my PC saying "Error [270] - update error". Tried 2 different roms, same thing happened, even tried hardSPL, also got the same error. Any ideas how to avoid this problem? Thanks in advance.
Click to expand...
Click to collapse
are you have unlocked your device with the XDA ALL UNLOCK at the time of going to Flash ROM..??
Um, probably not, all I did was try to hardSPL the device, but as I said, the problem occurs.
Well? Any solutions?
aco036 said:
Well? Any solutions?
Click to expand...
Click to collapse
try to hard reset device after that you can flash back with official ROM
Well I already tried hardSPL, but as I said, I got the same error while trying to preform it.
aco036 said:
Well I already tried hardSPL, but as I said, I got the same error while trying to preform it.
Click to expand...
Click to collapse
can you show your steps in doing flash hardSPL..??
Well sure, my device is fully charged and connected to USB, I run "ROMUpdateUtility", check whatever needs to be checked, go next, next... and it starts the process, I see 100% on it and after few seconds I get this error saying "update error" and my device restarts itself.
aco036 said:
Well sure, my device is fully charged and connected to USB, I run "ROMUpdateUtility", check whatever needs to be checked, go next, next... and it starts the process, I see 100% on it and after few seconds I get this error saying "update error" and my device restarts itself.
Click to expand...
Click to collapse
try to remove SIMCard and SD CARDS at the time will do the flash ROM
Same thing happened.
aco036 said:
Same thing happened.
Click to expand...
Click to collapse
you're copying sspl.exe on your device..??
What you also have to run SDA ApplicationUnlock will do it at the time..?
try to follow instruction that have been given
No, I'm not copying anything on my device, all I did is connect it to my PC via USB and run bootloader, thats it.
I haven't been given any instructions for preforming hardSPL.
EDIT: I just used SDA ApplicationUnlock, said "Phone is not unlockable", then when I pressed OK, it says "SDA successfully unlocked. PLEASE REBOOT SDA NOW!" Did that, tried HardSPL once more, again I got the same error message.
aco036 said:
No, I'm not copying anything on my device, all I did is connect it to my PC via USB and run bootloader, thats it.
I haven't been given any instructions for preforming hardSPL.
EDIT: I just used SDA ApplicationUnlock, said "Phone is not unlockable", then when I pressed OK, it says "SDA successfully unlocked. PLEASE REBOOT SDA NOW!" Did that, tried HardSPL once more, again I got the same error message.
Click to expand...
Click to collapse
of course you get an error message because you do not copy spl.nb, spl.lnk and jumpspl.exe to the root device ..! it means you did not follow procedures or instructions given...
you try to flash back and follow the instructions given, OK
Sigh, all the same problems doing these upgrades. Please read first about the various unlocks here. Then come back and let me explain further:
You MUST application unlock your device. So far you have NOT done it! Search for an "on-device" application unlock called "HTC Unlock" - this will do the trick (it basically macros a signed registry editor) and a subsequent run of the SDA Application unlock will succeed (not sure if still needed though).
The CID check avoidance by using an SPL replacement will only work if 1.) has succeeded
Good luck
First you must unbrick Device, upgrade SHIP ROM etc...
Hi everyone,
The flyer recently got htc's own online bootloader unlocker. I'm trying to work through the steps but everytime I type in fastboot oem get_identifier_token it returns a err command error. Is there something I'm doing wrong, I have installed HTC sync on win 7, with all the sdk stuff that it asks for but I can't seem to get this to work. Thanks in advance.
what's the error?
sorry was on vacation...
the error is "INFO[ERR] command error!!!" i think all my drivers and what not installed correctly, im not quite sure what's wrong here.
If anyone could spare a moment that would be most appreciated. I have searched for hours and my laptop is crying under the "weight of a thousand tabs" at the moment and have finally decided that my problem is not going to be solved by more forum browsing. Luckily I have all the links to tutorials I was following so I can pinpoint exactly where things went wrong.
The carrier: Virgin Mobile
The problem: Stuck in bootloader, no options working. Recovery and factory reset both yield nothing. RUU fails with error 170.
The History: I decided I was going to try and root my phone today. That actually worked via stock. Followed a guide that showed me how to unlock the phone (using HTCDEV) and pushed TWRP as my recovery.img. I flashed the stock ROM and had root access. Then I was following another guide to obtain S-OFF. It said that I should flash SetMainVersionLow via my recovery and the next step was to run "fastboot oem lock" which worked. Then it told me to run the RUU.exe which simply gives me error 170 "USB Connection Error". I was running adb and fastboot commands early from this same machine, and nothing changed from the point of "fastboot oem lock" and running the RUU, though now my device won't even show up in fastboot or adb.
Any help would be most appreciated. I'm 12 hours in surfing on the web for solutions and have got nothing. I have learned that this site rocks (just looking through posts and the general responses people get) and you can bet and help some stranger will give me on the internet will be paid forward five times over. I'm a computer major in school so I am well versed with technology but as you can tell my rooting experience is non-existent. Thanks all.
More info:
Windows 8 64-Bit
Bootloader displays the following:
*** RELOCKED ***
*** Security Warning ***
SHOOTER XC SHIP S-ON RL
HBOOT-1.58.0000
RADIO-1.09.00.0108
OpenADSP-v2.6.0.226.00.0217
eMMC-boot
May 17 2012,15:06:44
EDIT: I have, through restarting both laptop and phone a few times, obtained fastboot. My RUU now proceeds past where I would encounter error 170, but still fails. When I unplug the USB it says HBoot older. Anyone have a "newer" RUU?
fastboot getvar cid = SPCS_002
fastboot getvar mainver = 1.00.000.0
I was trying to use:
RUU_Shooter_ICS_35_S_Sprint_WWE_VM_1.13.652.2_Radio_1.06.00.0426_NV_1.53_144_release_262287_signed.exe
I also tried:
RUU_Shooter_ICS_35_S_Sprint_WWE_2.89.651.2_Radio_1.09.00.0706__NV_NV_SPCS_1.43_release_271101_signed.exe
'
which gave me the error "CID incorrect"