Related
I have just tried flashing WM6 on to a Friends QTEK 8500, it went wrong Doh!!!.
I had already last Friday put on it the version with non wroking GPRS and this went without issue. I then reflashed my own one with a GRPS working version (went without a problem) and then tried his. I can get it into the boot loader screen but nothing else. I have tried SD card flashing (3 cards) 1x 512MB Card and 2 x 2GB card all formatted as FAT32 with file on the root the phone searches for it but doesnt find it.
Please any advise.
vallancen said:
I have just tried flashing WM6 on to a Friends QTEK 8500, it went wrong Doh!!!.
I had already last Friday put on it the version with non wroking GPRS and this went without issue. I then reflashed my own one with a GRPS working version (went without a problem) and then tried his. I can get it into the boot loader screen but nothing else. I have tried SD card flashing (3 cards) 1x 512MB Card and 2 x 2GB card all formatted as FAT32 with file on the root the phone searches for it but doesnt find it.
Please any advise.
Click to expand...
Click to collapse
First of all, REMEMBER, your phone is NOT bricked until it goes to BOOTLOADER mode.
Have you made SuperCID before flashing? What firmware are you trying to flash via bootloader mode?
Erofich said:
First of all, REMEMBER, your phone is NOT bricked until it goes to BOOTLOADER mode.
Have you made SuperCID before flashing? What firmware are you trying to flash via bootloader mode?
Click to expand...
Click to collapse
When you say booloader mode what does that look like. At the moment if I reboot the phone I get the HTC Mobility windows by Erofich screen.
When you hold down camera and record button and then power on the device I get brifely the white scrren looking for SD card it then goes to the tri-colour screen and does nothing.
I beleive I have CID it as I did the same on this as I did on mine i.e. ran the unlock according to the sticky.
I than put on this
Windows Mobile 6 AKU 0.5.0 (5.2.1711 Build 18165.0.5.0) WWE v5c
Yours i beleive (excellent work by the way)
and it all worked fine bar GPRS I relay needed GPRS so I used
http://forum.xda-developers.com/showthread.php?t=368715
using the clean one which updated fine on my phone but when i tried it on my friends it fell over at about 83% I followed the recovery intructions but this did not work.
When you get into bootloader screen by pressing RECORD and CAMERA buttons, then you MUST flash back to the STOCK ROM first. You can't flash any custom WM6 at this point. Only AFTER you have the stock ROM flashed, you can use SDA_ApplicationUnlock.exe to app unlock the phone, and copy the SoftSPL into the phone. Then run SPL.lnk.
To summarize: The built-in bootloader CANNOT flash WM6 and can ONLY flash a stock ROM. Once you go back to stock, you can then try to flash WM6 again. Anytime a flash fails, you must go back to stock first, then try again.
GnatGoSplat said:
When you get into bootloader screen by pressing RECORD and CAMERA buttons, then you MUST flash back to the STOCK ROM first. You can't flash any custom WM6 at this point. Only AFTER you have the stock ROM flashed, you can use SDA_ApplicationUnlock.exe to app unlock the phone, and copy the SoftSPL into the phone. Then run SPL.lnk.
To summarize: The built-in bootloader CANNOT flash WM6 and can ONLY flash a stock ROM. Once you go back to stock, you can then try to flash WM6 again. Anytime a flash fails, you must go back to stock first, then try again.
Click to expand...
Click to collapse
I am trying RUU_STAR100_3.6.251.0_02.67.30_QtekEUR_Ship I believe this is an original version 5 rom?
GnatGoSplat said:
you can use SDA_ApplicationUnlock.exe to app unlock the phone
Click to expand...
Click to collapse
This method works on Cingular ROM only, not Qtek.
vallancen
Hold CAMERA and RECORD button and press power button. When it goes to Bootloader tricolor mode connect your device to PC and run official Qtek 8500 RUU. Then make a reg (app) unlock:
Download regeditSTG2 which is digitally signed: http://4pda.ru/forum/attach/387522/regeditSTG2.zip
Then install it and change some registry values:
HKEY_LOCAL_MACHINE\Security\Policies\Policies\00001001 = 2
-> change to 1
HKEY_LOCAL_MACHINE\Security\Policies\Policies\00001005 = 16
-> change to 40
HKEY_LOCAL_MACHINE\Security\Policies\Policies\00001017 = 128
-> change to 144
HKEY_LOCAL_MACHINE \Security\Policies\Policies
-> create new key "0000101a": Dword = 1
HKEY_LOCAL_MACHINE \Security\Policies\Policies
-> create new key "0000101b": Dword = 1"
Click to expand...
Click to collapse
copy SoftSPL to the root of your device and run SPL.lnk
Then run WM6 RUU
Erofich said:
This method works on Cingular ROM only, not Qtek.
vallancen
Hold CAMERA and RECORD button and press power button. When it goes to Bootloader tricolor mode connect your device to PC and run official Qtek 8500 RUU. Then make a reg (app) unlock:
copy SoftSPL to the root of your device and run SPL.lnk
Then run WM6 RUU
Click to expand...
Click to collapse
When I plug into PC (XP SP2) and run the Qtek 8500 RUU it just times out and says it cant find device.
vallancen said:
When I plug into PC (XP SP2) and run the Qtek 8500 RUU it just times out and says it cant find device.
Click to expand...
Click to collapse
I have two phones one did work and one did not the one that worked shows version 1.02 on the tri colour screen the one I am having problems with shows 3.06 not sure if this is relevant.
Try removing the battery for about 30-seconds (or just removing the battery cover) and then put it back on. With the phone OFF, hold RECORD and CAMERA and plug in the USB while holding those buttons. It should go to the Bootloader. Run the QTEK RUU immediately after doing that.
If you sit at bootloader very long (more than a minute or so), for some reason it times out and the RUU won't work. It could be that's what's happening.
GnatGoSplat said:
Try removing the battery for about 30-seconds (or just removing the battery cover) and then put it back on. With the phone OFF, hold RECORD and CAMERA and plug in the USB while holding those buttons. It should go to the Bootloader. Run the QTEK RUU immediately after doing that.
If you sit at bootloader very long (more than a minute or so), for some reason it times out and the RUU won't work. It could be that's what's happening.
Click to expand...
Click to collapse
Tried that a couple of times just to make sure I was doing it correctly it goes into the tri colour screen I pressed the reflash option on the PC 1 second later this then sits there for a minute or so and times out "ERROR [260]" the phone did come on and has a USB in the bottom left corner so I presume the connection to the PC is OK.
I have just re-done mine again using the NEO rom (very nice) to make sure I am not going mad and that I did it correctly and this all went without a hitch.
Is there anyway I can get the phone to boot of a SPL on an SD Card I think if I could do this then I could get it back to 5 and start again.
No, it will only boot off the built-in SPL in ROM.
Did you try using the OEM .nbh file, naming it STARIMG.nbh and putting it on the SD card?
GnatGoSplat said:
No, it will only boot off the built-in SPL in ROM.
Did you try using the OEM .nbh file, naming it STARIMG.nbh and putting it on the SD card?
Click to expand...
Click to collapse
Yes tried that made sure formatted FAT32 etc. I know the SD card is ok because if I take my working phone and run the SPL link with the card in my good phone it finds the file and asks me if i want to reflash it. The non working phone with SPL3.06 does not do this.
You are not alone.
The bad news - the person in the post ended up having to exchange the phone.
It could be there's a bug in 3.06 SPL? Seems to be the case because I've flashed bad ROMs many dozens of times on my Cingular 3125 StarTrek and not once did I have any trouble flashing OEM ROM back on it.
Can I write the flash at a lower level with any tools i.e. pdocwrite or seomthing like that?
I don't believe so. Those programs require an Activesync connection (copies files to the phone). You could try the MTTY method, but I don't know if that works on StarTrek. I think it's some kind of terminal access into the bootloader, but what I've said so far is the extent of my knowledge about it.
vallancen said:
I have two phones one did work and one did not the one that worked shows version 1.02 on the tri colour screen the one I am having problems with shows 3.06 not sure if this is relevant.
Click to expand...
Click to collapse
I have a similar problem on a 3125 and the phone reports V4.01. I acquired the phone in this condition, so don't know how that came to be. When I try to update via USB, it tells me I need a newer update tool (to match the 4.01, I assume). What error message are you getting when you try to update via USB?
I have been struggling to flash (again) the great pro V2 rom, but I always used my VMWare based XP windows version on my Vista laptop. Today I could use a genuine XP Laptop and I could make a connection and start the upgrade!
Sounds good? That's what I thought too, until the upgrade stopped at 70% (and I didn't touch anything), because of a connection error. I followed the text on my PC screen and I finally it started flashing again for a few seconds and then my startrek suddenly restarted, but it stops at the first splash screen! I tried to get my device back to bootloader mode (push 2 soft buttons and start), but no bootloader mode, only the 1st splash.
I solved the problem.
Thank you for this thread
I tried flashing a new ROM to my i-mate smartflip and thought I had killed it, but going back to the wm5 OEM as suggested on this thread worked and I still have my phone. Now, am I brave enough to try upgrading it to wm6.1 (or even 6.5) again... Once again, many thanks!
somebody can me give the oem rom because i am same problem too on the secreen 3.06 i cant flashing anytihing rom somebody must me help
I have a problem:
I flashed my hd2 from a stocked rom 1.42 dutch version, with hspl 1.42. I installed a custom rom from: HTC HD2 Laurentius WWE 21891UltimatePOWER.
it worked fine for 2 or 3 days and then it stocked, i reseted the phone and
When i turn on my HD2, i get a white screen. and it doest go away. Even after softreset (volume button down in bootloader)
When i go in to bootloader i see this screen:
Pb81100 hx-bc
Spl-1.42.hspl xe
0x05
Cotullahspl 0x30
Click to expand...
Click to collapse
When i try to instal a rom by going in to bootloader en then start in win xp the update wont start, it stocked at 0 %
Then i tried to flash a orginal romt by sd:
it stocked at 7 % and i get this screen:
_______________________RUUNBH
PB81100___HX-BC
SPL-1.42.__hspl___XD
________________0x05
CotullaHSPL______0x30
Upgrade ROM code error
Please try again
Click to expand...
Click to collapse
- Then i tried to flash a radio rom by activesync, in xp it wont start,
- i tried flashing by sd and it stocked on 98%
- I tried different to install a rom and radio rom by vista, but also no succes
- I tried task 29 (by the Attached Task29 into a single exe.) to erease all data from the phone, but in windows by activesync it wont start
i tried al the above from windows 7.
Is there anyone that can help me, please i getting very desperate.
VERY VERY IMPORTANT! Try and read 2-3 times what is written here http://forum.xda-developers.com/showthread.php?t=609477
Only afterwards proceed to the following :
First of all....try and use Windows Vista or Windows 7.
Second of all....do not try to use task 29 because its a bit more complicated and it involves some drivers and so on!
Use this little thing here http://forum.xda-developers.com/showpost.php?p=5848003&postcount=19 and after its completed....flash a proper radio something like 2.08.50.xx which you can find on Radio dedicated section here http://forum.xda-developers.com/showthread.php?t=611787
After all these....flash a custom ROM but be careful to be one suited with your radio! Which is a radio appliable for most of custom ROMS BUT be VERY careful!
Another thing.....do not flash from SD Card....Use the CustomRUU tool and flash it via ActiveSync!
Do you get any particular error message? When in bootloader mode, does "usb" show at the bttom of the screen? If so, try moving to a different usb port, preferably at the rear of the pc, or try different cable or even different pc. If still no luck, try uninstalling and then re-installing the latest version of Activesync.
The White Screen issue sounds like the incorrect radio version for the rom. I'm not familar with the details of the particular rom, but there are certain rom/radio combinations that will do that if they do not match eg running a 2.10 based rom with a x.xx.51.xx radio. The phone works intially until a reset and then hangs.
viperd said:
VERY VERY IMPORTANT! Try and read 2-3 times what is written here ......
Click to expand...
Click to collapse
Thanks for the replay
I tried, flashing by activesync. i flashed it the first time by hspl (the tread you link to) and then by activesync. But like i said, the hd2 stops at a white screen, so i tried by every possible way i could think of. Also i tried task 39 by the tool you mention, but it still does not work.
But i will correct my ts.
@clydeb1
I tryd to flash different radioroms, but if it try by activesync it wont start and by sd-flash it stocks at 98%, but i will try a different active sync
Okay,
I tried the following options:
- I installed a newest activesync and tried to instal an new rom under windows xp. The update stocked at 0% and i tried to install radio rom, with the same results
- I installed the windows mobile on windows 7, and tried the same as in windows xp, and still the same results.
Then i tried flashing every rom from the site by the sd-method (after every bad flash i formatted the sd-card with fat32)
With the sd method the phone stocked at 99% and then gives the next images:
00018003
LEOIMG.nbh - Fail
Radio_V2Fail
Update terminate
update fail
Click to expand...
Click to collapse
IS there any one how has a solution for this problem
Ok....try from the beginning!
1.Get from here http://forum.xda-developers.com/showthread.php?t=611433 HSPL2_RUN.zip (extract the content in a folder named hspl ).2
2. For Windows 7 you need Windows Mobile Device Center ( WMDC ) NOT ActiveSync!! Get it here http://www.microsoft.com/windowsmobile/en-us/downloads/microsoft/device-center-download.mspx
3. Make sure in WMDC settings the USB connection is checked!
4. Take out your battery....insert it again! Start your phone while keeping pressed the Vol Down button! This will get you into bootloader! The screen should display USB on the lower part of the screen! (evidently connected to computer )
5. Flash HSPL2 select 2.08 version
6. Use that tool I recommended earlier.....http://forum.xda-developers.com/show...3&postcount=19
7. Enter again the bootloader and flash a Radio ROM ( try 2.08.50.xx ) via WMDC!
8. Flash either NRGZ 21898 or Cleanex 21898 versions ( I recommend these in particular because they work with the radio mentioned above and are also stable ROMs ).
P.S. Take out your SD card and SIM card while performing all these steps!
Hope you will solve it!
viperd said:
Ok....try from the beginning!
1.Get from here (extract the content in a folder named hspl ).2
2. For Windows 7 you need Windows Mobile Device Center ( WMDC ) NOT ActiveSync!! Get it here
3. Make sure in WMDC settings the USB connection is checked!
4. Take out your battery....insert it again! Start your phone while keeping pressed the Vol Down button! This will get you into bootloader! The screen should display USB on the lower part of the screen! (evidently connected to computer )
5. Flash HSPL2 select 2.08 version
6. Use that tool I recommended earlier.....
7. Enter again the bootloader and flash a Radio ROM ( try 2.08.50.xx ) via WMDC!
8. Flash either NRGZ 21898 or Cleanex 21898 versions ( I recommend these in particular because they work with the radio mentioned above and are also stable ROMs ).
P.S. Take out your SD card and SIM card while performing all these steps!
Hope you will solve it!
Click to expand...
Click to collapse
Thanks for the advise
I did every step. The first problem is: WMDC doest say there is a connection, while windows 7 say there is a connection also i see usb in the lower part of the screen.
In the same sequence as you right above. the hspl2 says it worked fine, but when i reset the boatlooder still says it has hspl 1.42 in stead of 2.08. The tool you recommended did't start. and says update error.
do you know something else i could do (or anyone else)
Give the phone to someone who can get it to work??
Give me your SD-CARD serial number.
I'ma make a goldcard for you.
sd-card max to 4gb!
And then try flashing stock nld 1.66 rom using sd-card.
Because you tried to fix it flashing a 'original rom?' from sd I think I know what's your problem.
Did you use a Dutch shipped rom while trying to fix or a WWE one?
If you flash a shipped rom from storage card it restores the original SPL and removes HSPL !
Try flashing a Dutch shipped rom one more time from storage card, it will restore the original SPL made for your device.
korenbloem said:
Thanks for the advise
I did every step. The first problem is: WMDC doest say there is a connection, while windows 7 say there is a connection also i see usb in the lower part of the screen.
In the same sequence as you right above. the hspl2 says it worked fine, but when i reset the boatlooder still says it has hspl 1.42 in stead of 2.08. The tool you recommended did't start. and says update error.
do you know something else i could do (or anyone else)
Click to expand...
Click to collapse
Thanks mate, if my suggestion doesn't work hopefully you can help him.
xmoo said:
Give me your SD-CARD serial number.
I'ma make a goldcard for you.
sd-card max to 4gb!
And then try flashing stock nld 1.66 rom using sd-card.
Click to expand...
Click to collapse
@Korenbloem,
A simple hardreset would have fixed your issue as well.
Instead of all kind of panic experiments like mtty/ flashing radios/roms from sd you could have come to me and I would have helped you.
You flashed a very old rom from the rom archive but never the less that rom is intensivily tested by me and the beta team.
I have no idea what kind of software you installed/tweaks you did or anything else but also with installing the wrong software it could cause the rom not to boot anymore.
Sorry to tell you but these 'bricking' stories are mostly caused by unexperiened users and it
making me sad to see more people are opening threads like this blaming a rom and causing a panic reaction in public destroying our work.
I realy hope you fix your device and I will try to help you but this isn't a rom issue.
Leo
Laurentius26 said:
Because you tried to fix it flashing a 'original rom?' from sd I think I know what's your problem.
Did you use a Dutch shipped rom while trying to fix or a WWE one?
If you flash a shipped rom from storage card it restores the original SPL and removes HSPL !
Try flashing a Dutch shipped rom one more time from storage card, it will restore the original SPL made for your device.
Click to expand...
Click to collapse
Thanks for the adivse, but i already tried that with an orginal rom, but i will try it again, mabey there is a difference with a shipped rom.
The first thing i did was a hard reset, but that did't worked. (the phone is in this shape for 1 month now).
Second. I am not blaming you or anyone. I flashed the wrong radio rom i think (cant remember witch one) And that is my own fault. I never wanna make the suggestion that it is because of youre rom.
I took a risk by flashing my phone. and i is my responsibility.
Edit: I tried a shipping rom nld. But it gives the same error as always, only after 7%. But thanks for the advise
@ Xmoo, First of al thank you that you want to help with a sollution. But what does that mean a goldcard and what are the consequences of using it.
Laurentius26 helped me with fixing my device.
The problem was the radio. and by flashing a factory rom from t-mobile, the hspl was reset to spl 2.00. After that he flashed a orginal shipped rom (the orignal one from my device). And the rom is fixed again SPL 1.66 is now on the device.
Laurentius thanks for al the help!!!!!
HD2 bricked?
Hi, I urgently need your help. I used my hd2 on a vodafone branded rom 1.44. Last week I installed a Vodafone NLD 1.72 rom , + froyostone 3.4 Rom,kernel 8.5 (with hspl). Yesterday my touchscreen has stopped fully .. . The next, I've been in touch with HTC and they will pick up my phone tomorrow for repair. I have to remove hspl ofcourse .. so I happily try to flash official vodafone rom from the SD card, did nothing 1.72, 1.48 seemed to do until I restart and got an ROM code error. What to do: ( I am pretty desperate now .. when you start you get an exclamation point and then 'not allow' and then the tricolor. Is this due to the lack of the original 1.44 ROM? Apologies for this begging post and my poor English but I hope that someone has a solution to unbrick this device so he can up picked by HTC.
vanbasten88 said:
Hi, I urgently need your help. I used my hd2 on a vodafone branded rom 1.44. Last week I installed a Vodafone NLD 1.72 rom , + froyostone 3.4 Rom,kernel 8.5 (with hspl). Yesterday my touchscreen has stopped fully .. . The next, I've been in touch with HTC and they will pick up my phone tomorrow for repair. I have to remove hspl ofcourse .. so I happily try to flash official vodafone rom from the SD card, did nothing 1.72, 1.48 seemed to do until I restart and got an ROM code error. What to do: ( I am pretty desperate now .. when you start you get an exclamation point and then 'not allow' and then the tricolor. Is this due to the lack of the original 1.44 ROM? Apologies for this begging post and my poor English but I hope that someone has a solution to unbrick this device so he can up picked by HTC.
Click to expand...
Click to collapse
Do you have a branded Leo? If so, enter bootloader (remove battery, press volume down, insert battery), connect via usb (maybe you have to wait for driver installation), start the latest *.exe from your operator/carrier...
same problem here flashing an old radio... and now, everytime i try to flash a factory rom ship (RUU_Leo_HTC_PTG_1.66.410.1_Radio_Signed_15.30.50.07U_2.06.51.07_Ship) on 1% get the error 244 - invalid model id.
I tried to hard reset and now the message on the bottom of screen show me the right factory radio (2.06.51.07) of this rom but stays on this screen forever anyone knows what can i do? please help... tks a lot!
andreftx said:
same problem here flashing an old radio... and now, everytime i try to flash a factory rom ship (RUU_Leo_HTC_PTG_1.66.410.1_Radio_Signed_15.30.50.07U_2.06.51.07_Ship) on 1% get the error 244 - invalid model id.
I tried to hard reset and now the message on the bottom of screen show me the right factory radio (2.06.51.07) of this rom but stays on this screen forever anyone knows what can i do? please help... tks a lot!
Click to expand...
Click to collapse
Maybe it is because you flashed the wrong stock rom.
You should find the CORRECT STOCK ROM for your device, otherwise you need a gold card
silverwind said:
Maybe it is because you flashed the wrong stock rom.
You should find the CORRECT STOCK ROM for your device, otherwise you need a gold card
Click to expand...
Click to collapse
sorry but this rom i've downloaded from htc.com after insert model and my hd2 serial number and work for a while, but after flash hspl 1.42 to install another rom, when i flash a new radio version get the problem! so i flash again hspl to recovery for SPL 1.42.000 and then, nothing more is functional
tks 4 help... have anyone other solution?
andreftx said:
sorry but this rom i've downloaded from htc.com after insert model and my hd2 serial number and work for a while, but after flash hspl 1.42 to install another rom, when i flash a new radio version get the problem! so i flash again hspl to recovery for SPL 1.42.000 and then, nothing more is functional
tks 4 help... have anyone other solution?
Click to expand...
Click to collapse
The 1.66 ROM you posted above has radio version 2.06.51.07 with it. So have you considered trying to flash that radio version and then flash the ROM. I know if you get the ROM to flash it will flash that radio anyway. But you seem to think you flashed a wrong radio so just thinking out loud here.
Hello,
I'm about six hours into the process of trying to revive a nonfunctional HD2 that I purchased. I'm going batty!
Here is my status:
1) have installed SPL-2.08.HSPL 8G XE (0x05, 0x40) Cotulla HSPL
2) Have downloaded a few different roms (Chucky, TMO official, Energy) but they either get stuck at 0% or 9% (the highest it's gotten)
I'm getting pretty good at pulling the battery - it's like a new skill I never hoped to have!
I'm getting pretty frustrated because I've read about a hundred different posts on this site and I see that people are getting around this, but I'm starting to wonder if my phone has an issue that I can't resolve?
The phone doesn't boot up at all - it just says "Upgrade ROM code error, Please try again". Prior to my goofing with it, it just got stuck at the "Stick Together" screen. (Unwittingly bought it that way)
If I use the HSPL3_PKG to install/remove HSPL, it only works (connects to the phone) about one out of ten times, and out of the ~ten times I have gotten it to work, it only completed twice with a "We Hacked It" screen. The rest of the time it errors out just as I think it's getting the job done.
If I boot to the bootloader screen, I can put the USB cable in and see it change from Serial to USB (I've tried the thick and thin cables as some have suggested and haven't noticd a difference yet)
Then I kick of a rom update using the update utility that comes packed with it, and either the update process stops at 0% or it has made it all the way to 9%.
I'm in a position to get a replacement from TMO via the person who bought it (two for one, wife didn't like it, I bought it off of him) but I would rather not.
Any suggestions?
The part number of the phone is 99HKY001-00 B
jimmyswinger said:
Hello,
I'm about six hours into the process of trying to revive a nonfunctional HD2 that I purchased. I'm going batty!
Here is my status:
1) have installed SPL-2.08.HSPL 8G XE (0x05, 0x40) Cotulla HSPL
2) Have downloaded a few different roms (Chucky, TMO official, Energy) but they either get stuck at 0% or 9% (the highest it's gotten)
I'm getting pretty good at pulling the battery - it's like a new skill I never hoped to have!
I'm getting pretty frustrated because I've read about a hundred different posts on this site and I see that people are getting around this, but I'm starting to wonder if my phone has an issue that I can't resolve?
The phone doesn't boot up at all - it just says "Upgrade ROM code error, Please try again". Prior to my goofing with it, it just got stuck at the "Stick Together" screen. (Unwittingly bought it that way)
If I use the HSPL3_PKG to install/remove HSPL, it only works (connects to the phone) about one out of ten times, and out of the ~ten times I have gotten it to work, it only completed twice with a "We Hacked It" screen. The rest of the time it errors out just as I think it's getting the job done.
If I boot to the bootloader screen, I can put the USB cable in and see it change from Serial to USB (I've tried the thick and thin cables as some have suggested and haven't noticd a difference yet)
Then I kick of a rom update using the update utility that comes packed with it, and either the update process stops at 0% or it has made it all the way to 9%.
I'm in a position to get a replacement from TMO via the person who bought it (two for one, wife didn't like it, I bought it off of him) but I would rather not.
Any suggestions?
The part number of the phone is 99HKY001-00 B
Click to expand...
Click to collapse
After HSPL Install RADIO 2.14.50_04 then TRY to install latest Energy ROM.. Should work.
netvpn7 said:
After HSPL Install RADIO 2.14.50_04 then TRY to install latest Energy ROM.. Should work.
Click to expand...
Click to collapse
Even if it us a TMOUS HD2? I will give it a try, but I want to be sure before doing it!
Thanks for the reply
netvpn7 said:
After HSPL Install RADIO 2.14.50_04 then TRY to install latest Energy ROM.. Should work.
Click to expand...
Click to collapse
Once you have Hard-SPL on the device you don't need to worry about that anymore. Flashing Roms and radios will not overwrite it, that's what makes it "Hard". To make sure it's on there go into bootloader and it should show 2.08.hspl.
As for the radio, for TMOUS, just make sure it's a x.xx.50.xx radio (not a .51) and you'll be fine. If you have radio 2.10.50.xx you shouldn't have to change it.
So now I would try downloading one of the stock shipped Tmo ROMs (2.13 or 2.14). Then remove Sim and SD and go into bootloader, connect USB to PC and make sure it says USB on the device (not serial) and run the ROM Update Utility (RUU.exe). See if that works.
i also got this problem ,will try ur method n c
after hspl ,cant flash finish radio 2.14 it says ERROR (290) INVALID COMMAND.
excelpass said:
after hspl ,cant flash finish radio 2.14 it says ERROR (290) INVALID COMMAND.
Click to expand...
Click to collapse
You need HSPL..
HSPL done ,i tried a lot of files only Miri & Dinik n Duttys Leo Sense file can b flash successfully ,it went into menu once but now hang at htc startup again,,is this hardware problem?
i had the same problem last week. Drove me nuts.
i found there are more than one version of HPSL 3.
you have to download the latest one. for more info,
read my posts at
http://forum.xda-developers.com/showthread.php?t=789506&page=18
So you need HardSPL3 (the version is DarkForces Team HardSPL3 by bepe and Cotulla 21.06.2010)
If it still doesnt work, take a photo and post your screen
Still no go...
I have installed SPL-2.08.HSPL 8G XE (0x05, 0x40) Cotulla HSPL, the latest version I could find.
I just tried to flash RUU_Leo_1_5_TMOUS_3.14.531.0_Radio_15.42.50.09U_2.14.50.04_LEO_1.5_Ship and it consistently flakes out at 8%.
I charged the phone all night, booted to the tricolor screen, kicked off the update as an administrator in Win7, the phone got to 8% and then the update flaked out on the PC - "The ROM update encountered communication errors during the update process" (Error [276])
I genuinely think that this phone is bunk - I'm just going to have the fellow I bought it from call in for a warranty replacement.
Thanks for your help, everyone...
SD card flash...
Hi,
I could not see it anywhere in this thread, and also I'm not certain if it is possible on a HD2. But on my xperia I'm usualy flashing from a SD card, copy the image over rename it as KOVSIMG.NBH (guess it would be something like LEOROM.NBH).
Than by pressing (and holding) volume down + power button while the device is off going to the boatloader screen which detects the card (must be inserted and flash from it IF there is the correct file loaded on the card.
Dude,
Did you actually download the HardSPL3 version from DarkForces Team?
If not, dont second guess anything. And if it works, you'll get your phone back.
The file name to download is "HSPL3_PKG.exe". Its by bepe and Cotulla 21.06.2010
If you downloaded the right version. it will support ALL LEO types, and all the SPL versions below:
SPL 1.42.0000
SPL 1.62.0000
SPL 1.66.0000
SPL 2.07.0000
SPL 2.08.0000
SPL 2.10.0000
you just select which SPL version to install in the Choose SPL screen. This version also disables the CID Check.
Dont knock it before you try it ..
+1
jimmyswinger said:
I have installed SPL-2.08.HSPL 8G XE (0x05, 0x40) Cotulla HSPL, the latest version I could find.
I just tried to flash RUU_Leo_1_5_TMOUS_3.14.531.0_Radio_15.42.50.09U_2.14.50.04_LEO_1.5_Ship and it consistently flakes out at 8%.
I charged the phone all night, booted to the tricolor screen, kicked off the update as an administrator in Win7, the phone got to 8% and then the update flaked out on the PC - "The ROM update encountered communication errors during the update process" (Error [276])
I genuinely think that this phone is bunk - I'm just going to have the fellow I bought it from call in for a warranty replacement.
Thanks for your help, everyone...
Click to expand...
Click to collapse
Exactly in the same situation and dont know what to do...
snooffy said:
Hi,
I could not see it anywhere in this thread, and also I'm not certain if it is possible on a HD2. But on my xperia I'm usualy flashing from a SD card, copy the image over rename it as KOVSIMG.NBH (guess it would be something like LEOROM.NBH).
Than by pressing (and holding) volume down + power button while the device is off going to the boatloader screen which detects the card (must be inserted and flash from it IF there is the correct file loaded on the card.
Click to expand...
Click to collapse
Yes you are correct you can flash via SD card. You need a 4GB or lower SD card. This is not to say other higher GB SD card will not work, it is just that it has been stated many times the higher SD cards sometimes work to flash a ROM and sometimes don't. The card needs to be formatted with Fat 32. You have to find the RUU_(wharever).nbh and rename it to leoimg.nbh ( you almost got it righ tsnoffy lol) and copy it to your SD card. insert SD card into phone and hold the volume down botton down anx tap the power button keep holding the volume down button down until you see bootloader come up and say searching then let go of the volume down button. The ROM will flash.
i task29 my hd2 and flashed new radio now phone wont boot or anything i'm lost this is the radio i flashed Leo_radio_2.05.50.11_TMOUS.zip and now nothing cant do anything no usb connection nothing it is a tmob us phone with hardspl 2.08 on it i don't get it?
Rotary Parts said:
i task29 my hd2 and flashed new radio now phone wont boot or anything i'm lost this is the radio i flashed Leo_radio_2.05.50.11_TMOUS.zip and now nothing cant do anything no usb connection nothing it is a tmob us phone with hardspl 2.08 on it i don't get it?
Click to expand...
Click to collapse
Not sure what the problem is.
I use Task29 all the time and have no problems.
I do not have a T-Mobile phone and the radio you listed is for T-Mobile.
What ROM did you have on the HD? Did you flash just the radio after the Task29?
Rotary Parts said:
i task29 my hd2 and flashed new radio now phone wont boot or anything i'm lost this is the radio i flashed Leo_radio_2.05.50.11_TMOUS.zip and now nothing cant do anything no usb connection nothing it is a tmob us phone with hardspl 2.08 on it i don't get it?
Click to expand...
Click to collapse
Sorry if this sounds like a silly question but did you flash a new rom after doing task29?
Task29 completley wipes your phones nand, so everything is gone. Flashing a new radio isnt going to do much good if there is no rom installed on phone either.
no i did not once i flashed radio it went blank and can't do anything no usb connection our anything
this is where the radio came from post 51
http://forum.xda-developers.com/showthread.php?t=611787&page=6
name of radio i flashed
Leo_radio_2.05.50.11_TMOUS.zip
Hope you find a solution, but I am not very hopeful.
If you do, please post it as I would really like to know how you did it.
Rotary Parts said:
no i did not once i flashed radio it went blank and can't do anything no usb connection our anything
this is where the radio came from post 51
http://forum.xda-developers.com/showthread.php?t=611787&page=6
name of radio i flashed
Leo_radio_2.05.50.11_TMOUS.zip
Click to expand...
Click to collapse
This is pretty basic, but you do have to put your phone into bootloader manually after task 29. Take off the back cover, hold down the volume rocker, and hit the red reset button. Continue to hold down the volume until the multi-colored bootloader screen shows up. Then you can connect the USB and flash.
Please help anyone. Now phone not works. back screen always! jus when i connect it to usb pc shows found new hardware Qualcomm CDMA Technologios MSM.
Sorry, pushed thanks button accidently
Well, are you able to enter bootloader? Push volume button down (when the phone switched off) and push switch on button (end call). See if you have hspl on three-colored screen, then connect phone to pc. If you see USB, then flash original Rom. Then you can flash any rom according to cooker instructions. But I would recommend to install HSPL.
This could happen if you flashed radio without having HSPL on.
Skyguar said:
Sorry, pushed thanks button accidently
Well, are you able to enter bootloader? Push volume button down (when the phone switched off) and push switch on button (end call). See if you have hspl on three-colored screen, then connect phone to pc. If you see USB, then flash original Rom. Then you can flash any rom according to cooker instructions. But I would recommend to install HSPL.
This could happen if you flashed radio without having HSPL on.
Click to expand...
Click to collapse
Now press who you want... NO three-colored screen. Only Qualcomm CDMA Technologies MSM in device manager. Yes i had HSPL.. Actually im in shock now my HD2 really no longer works can't believe it
try to remove the battery for 10 seconds and then put it back and try to enter bootloader.
Try many times if u do not get it first time.
Flash ur HD2 with the original ROM.
WBR
Siemens Lover
SiemensLover said:
try to remove the battery for 10 seconds and then put it back and try to enter bootloader.
Try many times if u do not get it first time.
Flash ur HD2 with the original ROM.
WBR
Siemens Lover
Click to expand...
Click to collapse
Try everything.. I thing jtag can help here ?
Is it a T-Mobile HD2? If yes, then you bricked it. .51 radios are strictly for non TMOUS HD2's
Have a look here maybe you can save it
http://forum.xda-developers.com/showthread.php?t=668347#6262090
stathis95194 said:
Have a look here maybe you can save it
http://forum.xda-developers.com/showthread.php?t=668347#6262090
Click to expand...
Click to collapse
relies on being able to get into bootloader, so cant help a radio brick.
@OP, you need JTAG or new mainboard or new phone.
stathis95194 said:
Is it a T-Mobile HD2? If yes, then you bricked it. .51 radios are strictly for non TMOUS HD2's
Have a look here maybe you can save it
http://forum.xda-developers.com/showthread.php?t=668347#6262090
Click to expand...
Click to collapse
Yes mine is HTC HD2 T-mobile from USA ..