Hi Everyone,
I was trying to unlock my Samsung Galaxy S3 I-747M (I'm on Bell in Canada). Everywhere I looked on the internet instructed me to downgrade my version to 4.1.1 and then enter the magic numbers to unlock my phone.
So I followed the steps. Downloaded version 4.1.1 of the ROM, ODIN, etc., except a couple of things went wrong:
1) I forgot to turn on USB debugging mode
2) I've now learned that I should not downgrade from 4.3 back to 4.1.1
When I tried to install the ROM via ODIN it didn't work. Based on the other thread, downgrading from 4.3 will hard brick the phone, so I guess I'm lucky it didn't work.
My question is, where do I go from here? I am ready to give up on the unlock process. I just want the phone to work again at this point.
The phone has the following on the screen:
ODIN MODE
PRODUCT NAME: SGH-1747M
CUSTOM BINARY DOWNLOAD: No
CURRENT BINARY: Samsung Official
SYSTEM STATUS: Official
QUALCOMM SECUREBOOT: ENABLE
Warranty Bit: 0
BOOTLOADER RP SWREV: 1
There is a warning symbol between an image of the device and a monitor and it states "Firmware upgrade encountered an issue. Please select recovery mode in Kies & try again."
I can get to the Downloading mode.
I got these messages in ODIN:
<ID:0/005> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> KIES_HOME_I747MUMBLL1_I747MPCTBLL1_688429_REV04_user_low_ship.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Odin v.3 engine (ID:5)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> sbl2.mbn
<ID:0/005> NAND Write Start!!
<ID:0/005> sbl3.mbn
<ID:0/005> aboot.mbn
<ID:0/005>
<ID:0/005> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Related
Hi Everyone,
I was trying to unlock my Samsung Galaxy S3 I-747M (I'm on Bell in Canada). Everywhere I looked on the internet instructed me to downgrade my version to 4.1.1 and then enter the magic numbers to unlock my phone.
So I followed the steps. Downloaded version 4.1.1 of the ROM, ODIN, etc., except a couple of things went wrong:
1) I forgot to turn on USB debugging mode
2) I've now learned that I should not downgrade from 4.3 back to 4.1.1
When I tried to install the ROM via ODIN it didn't work. Based on the other thread, downgrading from 4.3 will hard brick the phone, so I guess I'm lucky it didn't work.
My question is, where do I go from here? I am ready to give up on the unlock process. I just want the phone to work again at this point.
The phone has the following on the screen:
ODIN MODE
PRODUCT NAME: SGH-1747M
CUSTOM BINARY DOWNLOAD: No
CURRENT BINARY: Samsung Official
SYSTEM STATUS: Official
QUALCOMM SECUREBOOT: ENABLE
Warranty Bit: 0
BOOTLOADER RP SWREV: 1
There is a warning symbol between an image of the device and a monitor and it states "Firmware upgrade encountered an issue. Please select recovery mode in Kies & try again."
I can get to the Downloading mode.
I got these messages in ODIN:
<ID:0/005> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> KIES_HOME_I747MUMBLL1_I747MPCTBLL1_688429_REV04_user_low_ship.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Odin v.3 engine (ID:5)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> sbl2.mbn
<ID:0/005> NAND Write Start!!
<ID:0/005> sbl3.mbn
<ID:0/005> aboot.mbn
<ID:0/005>
<ID:0/005> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Apologies for the duplicate thread
It's my first time posting. I had multiple windows opened and I confused the 2 categories of S3. I should have posted under the I-747M one, when I didn't see my posting there I clicked back on my browser and ended up creating a new posting. Please ignore/delete the other posting. I don't know if there's a way to move this one to the correct category.
Hi to all! First of all, I am sorry if I put my problem in wrong forum. I'm new here...
I was trying to install Android Jelly Bean 4.2.2 firmware (I9105PXXUBMI3_I9105POXXBMJ1_I9105PXXUBMI1_HOME.tar.md5) on my Galaxy SII Plus via Odin_v3.09. Unfortunately, I put firmware file in field BL (in previous versions of Odin it was Bootloader) instead of AP. Odin finishes with status FAIL. Complete log is below:
<ID:0/005> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9105PXXUBMI3_I9105POXXBMJ1_I9105PXXUBMI1_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Odin v.3 engine (ID:5)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> SingleDownload.
<ID:0/005> sboot.bin
<ID:0/005> NAND Write Start!!
<ID:0/005> vc-firmware.img
<ID:0/005>
<ID:0/005> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
After that, phone is stuck in Download mode. I can't restart it, turn it off or boot it in recovery mode. All I can do is to boot it in download mode again or I get message "Firmware upgrade encountered an issue. Please select recovery mode in Kies & try again" (which, by the way, doesn't work because it Kies cannot see the phone in this state).
Any help would be much appreciated! Thanks guys!
Hi
Please can someone help me??
I downloaded this file (canada version of lollipop for SM-P900):
http://www.sammobile.com/firmwares/download/53868/P900UEU1COH2_P900XAC1COH2_XAC/
I used Odin 3.09 to try to install the file, and it said failed. Now when I try to power it up I get "Firmware upgrade encountered an issue. Please select recovery mode in Kies and try again".
When I connect it to Kies, Kies says it's not a compatible device. I know it is though, because I successfully connected in to Kies before I started doing all this.
I can still however enter download mode, but can't enter recovery mode (Power + Vol up + Home).
Thanks a lot
On the tablet screen, in download mode, it says:
ODIN MODE
PRODUCT NAME: SM-P900
CURRENT BINARY: Samsung Official
SYSTEM STATUS: Official
Secure Download : Enabled
KNOX WARRANTY ISSUE VOID: 0 (0x0000)
AP SWREV: A1
The message I get in Odin is:
<ID:0/006> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> P900UEU1COH2_P900XAC1COH2_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/006> Odin v.3 engine (ID:6)..
<ID:0/006> File analysis..
<ID:0/006> SetupConnection..
<ID:0/006> Initialzation..
<ID:0/006> Get PIT for mapping..
<ID:0/006> Firmware update start..
<ID:0/006> SingleDownload.
<ID:0/006> sboot.bin
<ID:0/006> NAND Write Start!!
<ID:0/006> boot.img
<ID:0/006> recovery.img
<ID:0/006> system.img
<ID:0/006> FAIL!
<ID:0/006>
<ID:0/006> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Thank you
I used Odin to flash back to the UK version of kitkat from Sammobile with no problems...
Any idea, from the Odin info, why the other one didn't work?
Thanks
Another update for anyone that's reading this/interested....
The Netherlands version of lollipop worked (http://www.sammobile.com/firmwares/download/49414/P900XXU0BOF2_P900OXA0BOF2_PHN/).
The canadian one didn't, no idea why...
Hello, so recently I bought my first samsung device and tried to root my Samsung Galaxy S6 Edge and I was a complete newbie in doing this so then my device keeps saying Recovery Is not Sendroid Enforcing on the start up screen. I Live in Australia and am currently with the carrier Vodafone.
Help PLease
So I tried doing a stock firmware update with a .tar I found somewhere that said it was for the SM-G925I Vodafone Australia so I downloaded I go on Odin Tick Auto Reboot and F. Reset time i then tick AP and select the .tar file it takes a while to check the file then it says leave cs I connect my phone to my pc I then press start and get fail. It says then on my phone SW REV. CHECK FAIL. DEVICE: 3, BINARY: 1
ODIN Script:
<ID:0/005> Removed!!
<ID:0/005> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> G925IDVU1AOC4_G925IVAU1AOC4_G925IDVU1AOC5_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Odin engine v(ID:3.1005)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> SingleDownload.
<ID:0/005> sboot.bin
<ID:0/005> NAND Write Start!!
<ID:0/005> FAIL!
<ID:0/005>
<ID:0/005> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Loquar said:
So I tried doing a stock firmware update with a .tar I found somewhere that said it was for the SM-G925I Vodafone Australia so I downloaded I go on Odin Tick Auto Reboot and F. Reset time i then tick AP and select the .tar file it takes a while to check the file then it says leave cs I connect my phone to my pc I then press start and get fail. It says then on my phone SW REV. CHECK FAIL. DEVICE: 3, BINARY: 1
ODIN Script:
<ID:0/005> Removed!!
<ID:0/005> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> G925IDVU1AOC4_G925IVAU1AOC4_G925IDVU1AOC5_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Odin engine v(ID:3.1005)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> SingleDownload.
<ID:0/005> sboot.bin
<ID:0/005> NAND Write Start!!
<ID:0/005> FAIL!
<ID:0/005>
<ID:0/005> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Click to expand...
Click to collapse
i am having same issues just trying to get my phone back to stock, have tried various different firmwares but just cant get odin to flash...
never had this issue on any previous fones and have been flashing many samsung devices for many years...
but the phone came to me in a bricked state so not sure as have read here that something to do with bootloader, not sure if phone was rooted or what firmware it was on before...
all i would like to do is get it back to stock firmware and running up an normal....
is there a simple way or simple files that i need?
I've been trying to root my galaxy s8 using Odin3 (v3.12) and CF-Auto-Root and I keep getting the same error. Odin is being run as administrator, I tried switching the usb port on my laptop, USB debugging on the phone is on. I couldn't find "OEM Unlock" in settings, I don't know if it's enabled, and if it is, how to disable it. Odin would get to a certain point in the process and the fail and then a bubble with red text appears on my phone saying "SECURE CHECK FAIL : recovery".
Odin's log:
<ID:0/005> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Odin engine v(ID:3.1203)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> SingleDownload.
<ID:0/005> recovery.img
<ID:0/005> FAIL! (Auth)
<ID:0/005>
<ID:0/005> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
If anyone knows what I'm doing wrong or what I can do, please keep the explanations simple, I'm a bit of a novice when it comes to these types of things.
Same problem.
Randomizzerr said:
I've been trying to root my galaxy s8 using Odin3 (v3.12) and CF-Auto-Root and I keep getting the same error. Odin is being run as administrator, I tried switching the usb port on my laptop, USB debugging on the phone is on. I couldn't find "OEM Unlock" in settings, I don't know if it's enabled, and if it is, how to disable it. Odin would get to a certain point in the process and the fail and then a bubble with red text appears on my phone saying "SECURE CHECK FAIL : recovery".
Odin's log:
<ID:0/005> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Odin engine v(ID:3.1203)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> SingleDownload.
<ID:0/005> recovery.img
<ID:0/005> FAIL! (Auth)
<ID:0/005>
<ID:0/005> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
If anyone knows what I'm doing wrong or what I can do, please keep the explanations simple, I'm a bit of a novice when it comes to these types of things.
Click to expand...
Click to collapse
I'm having the same problem. I've tried oden 3.11 and 3.12. Tried switching usb ports. Can't find oem unlock but didn't think the smg950u1 had it.
smg950u1 odin fail
Can someone help us?
BL
Bootloader is Locked
The phone's security probably doesn't allow it... probably the version this method worked for was a lower security version.