[Q] I9300 Screen issues - Galaxy S III Q&A, Help & Troubleshooting

Hi
Cutting a long story short, is there a screen calibration app/menu option for the S3? I cracked my screen the other week, and I have had the screen replaced (not by samsung). Ive noticed now that the screen intermittenly sometimes sticks, becomes non responsive and/or the image "vibrates" when I long press on an app to move it. OR when I try to hang up a call, 9/10 times the press doesnt "register"
Before I go and moan at the shop I got it repaired at, is there any app or any way of calibrating the screen ?
I should mention that the phone is not running a stock rom. It wasnt before the screen was replaced and everything ran flawlessly, even with the crack Now I'm no expert but I would suggest they've either fitted a dodgy screen / there's a loose connection or it needs calibration.
If anyone's wondering it is on Temasek's CM11 unofficial build. Although I had it on CM 11 for a while and the problem persisted.
I suspect it is a hardware issue with the replacement screen but I thought I'd ask.
Cheers
Andrew

Flash a full stock rom to test but it sounds like you've a hardware fault.

*#0*#
This is screen test function of sammy based roms. if you want you can try your screen with this

You cant calibrate capacitive screens
GT-I9300 cihazımdan Tapatalk kullanılarak gönderildi

If I remeber correctly this behavior happens when the screen is repaired without that special adhesive layer which originally glues everything together.

Back on stock rom, tried the calibration/diagnostic screen.... no dice, according to that it works ok lol.
It looks like I'm going back to the shop I got the repair done, to try and get them to fix it (again!) Bet they will try and charge me more money tbh I am almost at the point of living with it BUT I had two phone calls I could not answer today because the screen wasn't working properly, and that will not do
Edit :- found the accessibility options which allows me to answer/end calls using the hardware buttons. Still a bit gash but better than nothing.
Will see what the shop says, less urgent now, at least I have a way of answering the damn thing lol.

Related

HTC Touch Pro - screen doesnt work but everything else does

touch pro
screen does not respond!!
everything else works
i feel it vibrate when it turns on, the light in the center button lights up when charging
my friend was able to call me, and the lights and my ringtone went off
the keyboard lights up, the part below the screen with the center button works and lights up
basically yeah, everything except the screen works!
i tried taking the battery out and i did a soft reset
dont really want to do a hard reset (will all my contacts get erased?)
looked around the forum briskly for anything related to my problem but didnt find any
what should i do? i really need my phone to be working T__T
possibly...
http://forum.xda-developers.com/showthread.php?t=533350
typical problem with the touch pro...because its a slider you probably need to replace the flex cable from mother board to screen, i had same problem with mine i thought at first it was the digitizer but dont be fooled.
back up the pim file on the computer and see if you can get the phone replaced under warrenty would be my suggestion.
Not sure if you have fixed the problem yet or not but I just recently had this same issue. I replaced the phone under warranty and before I sent it back I installed MyMobiler to navigate the phone and save any files I wanted to keep locally on my PC. Obviously activesync saved all my contacts and whatnot as well.
The sad part was I had only had the phone a month and 2 weeks so they couldn't give me a brand new replacement since it was over the 30 days, so I had to settle for a Re-Man. blah
Oh well good luck mate!
I have the same problem. I just called tech support and had them sent me a new one. Something that may elongate your use before you get it replaced, press down on the screen between the lower buttons and the LCD screen (the Verizon logo). It seems that the more that i do it, the worse it get, but slowly. Here is a video of me making it work.
Good luck!

HD2 No Screen

Qeustion
My HD screen is off, and i cant seem to get it on again.
I just was working on it 1hour ago, took it out of my pocket and see that i have no screen.
Rebooted the phone, but no succes .. i see the screen turning on, but it light-gray (backlight) but no actual info/colors etc, also tryd a soft reset, no succes.
I have the Energy ROM Com5 build from 8July with the new 2.12 radio rom.
Could it be that in some way the screen died?
Hope someone can help me, im @ work now so i cant connect it with the PC.
When im home im planning to reflash the device ..
Thanks!
Weird
I just pressed a button and the screen turned on, and the colours/info just slowely fade away ... weird.
Could it be that the touchscreen is not oke anymore?
Or could it be a problem in the radio/rom i use? (and therefore a reflash could fix this?)
Hope its a easy sollution, otherwise ill be flashing it to stock and get it fixed by HTC.
Very very strange.
It seems to work again.
Anyone think i should reflash it to stock and try get a new one?
Are these signs of a screen going defect?
I dont know, first phone for me with touchscreen.
I would suspect a faulty screen, if it is still within warranty i would deffinately get a new one, however yes, try going back to stock first, see if it helps, it may be just a bad flash.
screen problem
I've had this and similar problems with my HD2, now on the 5th replacement from HTC in just 6 months of owning the phone. I also had the same problem on my HTC HD previously. Press the power key and just the buttons at the bottom light up but no response from the screen. Also had exactly the same problem your experiencing where you can faintly see the screen but not lit up. Flash it to stock rom and return to HTC for repair.
BEWARE!!! take some pics with date stamps of your handset before returning. They sent me 3 handsets all with the glass front panel not fitted correctly. Check the return handset carefully, you should be able to feel a lip between the casing and the screen as the screen is set a fraction lower than the casing. THis should be uniform all around. They tried telling me that i had damaged it myself despite calling them as soon as the handset had been delivered back to me.
micky9869 said:
Press the power key and just the buttons at the bottom light up but no response from the screen.
Click to expand...
Click to collapse
That's 'sleep of death', which affects loads of htc devices.
Oke i will stock it soon and return for repair.
I think its idd a screen problem, cause when the screen isnt functioning anymore, and when i put my ear on the glass, i hear a little squishing sound, like air is escaping .. it doesnt do that when the screen shows info/colour.

SGS2's screen flash randomly on lock screen

Hi guys,
My SGS2's screen suddenly had this problem, where the screen will flash randomly even though i locked it. To make matters worse, my home button not working now. I suspect it could be water got into the phone, when i tried to apply the screen protector the night before? What you guys reckon i should do? It's unfortunately out of warranty now.
Have you rooted flashed custom rom if so re-do it with full wipe
see if problem remains.because your out of warranty look for disassemble video
tutorial check all contacts and ribbons/possible water damage might need new screen this can be expensive if you don't do it yourself
i'm using non-rooted official rom XXPLX ICS, so i don't believe the problem is with the rom since it was ok for the past month. Must be been water that got into it...guess i'll just have to soak it in rice bag for a week like some advised and see how it goes...finger crossed...
ok just to update..now my screen seems to be ok now (no more flashing)..but seems like my home button is dead. Any way i can get around it? I find it hard to justify paying $200+ to fix a home button XD
I saw on the net there's some self repair tool for home screen but it just look too complicated...

[Q] touchscreen not working

I have a Galaxy S3 that I have been running CM 10.2 on for quite some time. Today I dropped the phone and cracked the screen. The phone still worked perfectly in every way despite the cracked screen. I used it for a few hours after without any issues. I took it to someone today to replace the screen assembly. When I got the phone back it turns on and the screen looks fine but it hangs on the samsung screen for 3-5 minutes before booting in to anything (booting the rom, recovery mode, download mode etc. all take 3-5 minutes to start) when the phone finally boots the touch screen does not work at all. All buttons work fine, including the bottom buttons (back and settings) for touch but no where else does the screen respond to touch.
So far I've tried:
- wiping cache
- factory reset
- re-installed CM 10.2 rom
- Took the back off the phone and checked all the connections, unclipped and clipped back in to be sure they were connected ok.
- Completely removed battery and all sim/sd cards for an hour
At this point I'm not sure if I'm dealing with a hardware issue (maybe they guy screwed something up when replacing the screen) or the digitizer/screen he used is faulty? I know this doesn't neccessarily mean anything but when I got it back the new screen still had the protective film etc. on it so I'm almost positive the screen assembly the guy used was at least new.
And I don't really understand where the 3-5 minute boot issue could come from? I wouldn't think it would be related to the screen/digitizer but I suppose anything is possible. What could explain this?
Is there any way this could be a software issue or any other troubleshooting I can attempt?
jfall said:
I have a Galaxy S3 that I have been running CM 10.2 on for quite some time. Today I dropped the phone and cracked the screen. The phone still worked perfectly in every way despite the cracked screen. I used it for a few hours after without any issues. I took it to someone today to replace the screen assembly. When I got the phone back it turns on and the screen looks fine but it hangs on the samsung screen for 3-5 minutes before booting in to anything (booting the rom, recovery mode, download mode etc. all take 3-5 minutes to start) when the phone finally boots the touch screen does not work at all. All buttons work fine, including the bottom buttons (back and settings) for touch but no where else does the screen respond to touch.
So far I've tried:
- wiping cache
- factory reset
- re-installed CM 10.2 rom
- Took the back off the phone and checked all the connections, unclipped and clipped back in to be sure they were connected ok.
- Completely removed battery and all sim/sd cards for an hour
At this point I'm not sure if I'm dealing with a hardware issue (maybe they guy screwed something up when replacing the screen) or the digitizer/screen he used is faulty? I know this doesn't neccessarily mean anything but when I got it back the new screen still had the protective film etc. on it so I'm almost positive the screen assembly the guy used was at least new.
And I don't really understand where the 3-5 minute boot issue could come from? I wouldn't think it would be related to the screen/digitizer but I suppose anything is possible. What could explain this?
Is there any way this could be a software issue or any other troubleshooting I can attempt?
Click to expand...
Click to collapse
Go and talk to the person who replaced your screen.. maybe has used faulty screen and also may be he has changed with some of the faulty parts..
suyash1629 said:
Go and talk to the person who replaced your screen.. maybe has used faulty screen and also may be he has changed with some of the faulty parts..
Click to expand...
Click to collapse
Very strange, but it looks like it was indeed a software issue after all. For some reason changing the screen out while having CM 10.2 installed did not play well together. I did a full wipe and went back to stock rom and touch is working now. I may try a new install of CM again to see what happens. Odd
jfall said:
Very strange, but it looks like it was indeed a software issue after all. For some reason changing the screen out while having CM 10.2 installed did not play well together. I did a full wipe and went back to stock rom and touch is working now. I may try a new install of CM again to see what happens. Odd
Click to expand...
Click to collapse
Strange issue.. never had it ever, m flashing CM from more than a year.. Try to do a new flash downloading new files..

Flashing/flickering/artifacting screen?

(UPDATE: Here is a link to a short video of my issue: https://youtu.be/YqKW3tU4Fhw)
So I cant seem to find ANY info relating to this issue aside from results for the LG G4, but the solutions for said phone are all over the place. Some are bad screen, some are related to sim tray, some are related to water damage and battery etc. So basically, about a month after buying this phone (KIW-L24 US version), the screen started to artifact and flash in and out randomly. There is nothing that seems to trigger it. I have set the phone down on a table while on the homescreen and watched the lightshow. It is basically a mixture of the problems seen in these videos (Feat. LG G4).
https://youtu.be/gAUkXLR7eQI And https://youtu.be/QstOH66pfiU.
Symptoms:
Screen will randomly start to flicker and fade in and out. I will also get crazy artifacting lines. (Think de-gaussing an old CRT monitor or simillar to what is seen in the second video)
If i see the problems happening, locking the phone and unlocking again will sometimes fix it temporarily. Other times the problem continues after i turn the screen back on.
Sometimes the screen will refuse to come back on. The backlight turns on, and the digitizer responds, but the screen is still black. Making sure the screen really is off, I can come back to the phone a few minutes later and it will turn on. Other times ill have to hard reset the phone (hold power button 10 sec) and it usually brings the screen back to life.
Background:
I bought the phone "used - Like New" from amazon. It came with all the original accessories and even still had the film protector on the back of the phone. I may have noticed these problems after I received the phone, but they really only started to show about a month after purchase.
At first I though it could be software related as I was running CM13 and something could have been corrupted, so i did not just a factory restore, but a full reflash. This didn't solve the issue. Restarting my phone and the reflash did help, but the problem returned. The inability to turn the screen on persists through a reset and I have to wait till the phone boots again to get the screen back. Sometimes takes more than one reboot. This pretty much confirms a hardware issue right? If i put the phone on a black screen, i can see three small fuzzy "dots" in a triangle shape in the top left quadrant. Could the screen have been damaged by whoever owned it before returning it? They are not dead pixels per se, but seems more like areas where the backlight is showing through ever so slightly more. Not visible unless you are on a black screen in a dark room. Ill upload a video showing some of the issues. Any help is appreciated!
im afraid you need a new display brodar...
Seems to be hardware issue. You can visit the nearest service center to get it fixed for few bucks if you don't have warranty.
Yeah that's what i figured, i just needed conformation. I was able to get amazon to take the return even though I was out of the return period. So at least ill be able to get a refund. Ill just pay the extra for a new one this time haha.
One question : Do u have over heat problem with ur phone ?? If u feel ur phone is more than work from the back dont replace . U'll damage the new screen also . Some ppl erported over heat cpu issue with honor ! ;.
KobaltPanther said:
(UPDATE: Here is a link to a short video of my issue:
)
So I cant seem to find ANY info relating to this issue aside from results for the LG G4, but the solutions for said phone are all over the place. Some are bad screen, some are related to sim tray, some are related to water damage and battery etc. So basically, about a month after buying this phone (KIW-L24 US version), the screen started to artifact and flash in and out randomly. There is nothing that seems to trigger it. I have set the phone down on a table while on the homescreen and watched the lightshow. It is basically a mixture of the problems seen in these videos (Feat. LG G4).
And
.
Symptoms:
Screen will randomly start to flicker and fade in and out. I will also get crazy artifacting lines. (Think de-gaussing an old CRT monitor or simillar to what is seen in the second video)
If i see the problems happening, locking the phone and unlocking again will sometimes fix it temporarily. Other times the problem continues after i turn the screen back on.
Sometimes the screen will refuse to come back on. The backlight turns on, and the digitizer responds, but the screen is still black. Making sure the screen really is off, I can come back to the phone a few minutes later and it will turn on. Other times ill have to hard reset the phone (hold power button 10 sec) and it usually brings the screen back to life.
Background:
I bought the phone "used - Like New" from amazon. It came with all the original accessories and even still had the film protector on the back of the phone. I may have noticed these problems after I received the phone, but they really only started to show about a month after purchase.
At first I though it could be software related as I was running CM13 and something could have been corrupted, so i did not just a factory restore, but a full reflash. This didn't solve the issue. Restarting my phone and the reflash did help, but the problem returned. The inability to turn the screen on persists through a reset and I have to wait till the phone boots again to get the screen back. Sometimes takes more than one reboot. This pretty much confirms a hardware issue right? If i put the phone on a black screen, i can see three small fuzzy "dots" in a triangle shape in the top left quadrant. Could the screen have been damaged by whoever owned it before returning it? They are not dead pixels per se, but seems more like areas where the backlight is showing through ever so slightly more. Not visible unless you are on a black screen in a dark room. Ill upload a video showing some of the issues. Any help is appreciated!
Click to expand...
Click to collapse
Try moving to stock once , if it fixed stick to it for few days . 99% of possible cases for hardware issue .
So better request for a replacement from huawei . but don't mention them that u bought it used . tell them u bought it new

Categories

Resources