Hi
I got my daughter a 7" rk3026 tablet for xmas. I was playing around with it and trying to put cwm for the 3066 on there hoping it would work but now ive bricked the recovery. It boots up fine but will not go into recovery mode. Does anyone know of a cwm or twrp that will run on this? any roms or firmware any? I can find out nothing about these tabs on the net.
Spec
Model 7“ RK3026 Android Dual Core Tablet PC
CPU Rockchip RK3026, 1.0GHz, Cortex A9 Dual Core; GPU: Mali-400 MP2
Operation System Android 4.2.2
RAM 512MB
ROM(Memory) 4GB Nand Flash
Shell Material Plastic
Screen Size 7 Inch
Type Capacitive Screen
Display LCD
Resolution 800 x 480px
Visible Angle 120°
Extend Card Support TF card up to 32GB extended
Camera Dual camera, both are 0.3 megapixels
Gravity Sensor Yes
Multi-Touch Yes, 5 points touch
Flash Support Flash 11.1
Play Store
Yes
Bluetooth No
battery 2800mAh
Any suggestions?
Cheers
Chris
i have the same tablet , my wifi connect put no internet , try to flash another frimware and now just white screen
Related
Heey guys, i lost my stock recovery AAAH
I was so dumb installing a CWM not made for my phone...
It still boots, works, but i would really like my recovery back!
But i do not have a backup...
Please help me! my phone is: WOLFGANG at-as43d4
Android 4.1 (Jelly Bean)
MT 6577 T, 1.2 GHz Dual-Core
850/900/1800/1900 MHz
850/1900/2100 MHz
2 Simcards Dual standby
4 GB ROM
512 MB RAM
Micro SD max 32GB
ACCU
Power 1500mAh
Charge time 4 Hours
Calling time Max 360 Minutes
Standby time Max 300 Hours
SCREEN
Size 4.3″ inch
Resolution 480*800 WVGA
Type TFT-LCD
CAMERA
Pixels Backcamera 5.0 Mpx AutoFocus
Pixels FrontCamera 0.3Mpx
Torch LED
MULTIMEDIA
Music MP3/MIDI/WAV/AMR/AAC
Movie MP4/3GP
Radio Yes
CONNECTIONS
USB Micro USB
Headphones 3.5MM Jack
Connections
Bluetooth 4.0
Wi-Fi Yes with tethering
GPS Yes
THANKS! :good:
If it still works, install Terminal Emulator. I updated my CWM a couple days ago like this
winsettr said:
You can also use Terminal Emulator: (I prefer to place the .img file in the root of the SD card and rename the image to something simple like touch.img so I don't have to type the long name from my phone)
su
flash_image recovery /sdcard/touch.img (or whatever the recovery image is named)
reboot recovery
Enjoy!
Click to expand...
Click to collapse
Hi, I've a problem with a tablet Wolder mitab Iron. I know that this tablet is unknow for much people. Well, my uncle try to move app to external SD card and he unmount the "hard disk" of the tablet. He gave me the tablet to repair it and I run the recovery mode for do a hard reset but it doesn't do nothing, Android not run. Then I install the firmware of Wolder mitab New Age but when Android stars the touch screen doesn't work. He gave me other mitab Iron and I installed CWM and I brick the tablet, it doesn't run Android or Recovery mode. Can someone tell me one soluciton for this? Is there a ROM for this tablet for repair the first table? Is there one solution to repair the second table?
The tablet has the follow specifications:
-Andoid 4.2 (Jelly Bean)
-CPU Cortex A9 Dual Core 1GHz
-Chipset Allwinner 20
-RAM 1GB
-Graphics Mali 400 Dual Core
-4 GB of internal memory
Help!!:crying:
PD: I'm not sure where I post this, I think it's the best site. Sorry if you don't understand me, my English isn't the best.
temerariomalaga said:
Hi, I've a problem with a tablet Wolder mitab Iron. I know that this tablet is unknow for much people. Well, my uncle try to move app to external SD card and he unmount the "hard disk" of the tablet. He gave me the tablet to repair it and I run the recovery mode for do a hard reset but it doesn't do nothing, Android not run. Then I install the firmware of Wolder mitab New Age but when Android stars the touch screen doesn't work. He gave me other mitab Iron and I installed CWM and I brick the tablet, it doesn't run Android or Recovery mode. Can someone tell me one soluciton for this? Is there a ROM for this tablet for repair the first table? Is there one solution to repair the second table?
The tablet has the follow specifications:
-Andoid 4.2 (Jelly Bean)
-CPU Cortex A9 Dual Core 1GHz
-Chipset Allwinner 20
-RAM 1GB
-Graphics Mali 400 Dual Core
-4 GB of internal memory
Help!!:crying:
PD: I'm not sure where I post this, I think it's the best site. Sorry if you don't understand me, my English isn't the best.
Click to expand...
Click to collapse
here you can find rom for wolder mitab iron 9"
can not put address
I attached a picture of address
I have a tablet with these specs:
Rk3168 dual core arm A9 cpu, 1GB RAM, 8GB storage, 7" 1024x600 display, wifi rtl8188etv
I managed to mess it up and I can't get my hands on the stock ROM.It has no volume buttons either so couldn't recover it.
I found a few working custom ROMs for it but none of them match my device perfectly.
Some of them don't have the wifi drivers I need and a couple I found with the correct driver don't have the correct RAM/ROM size.
From my understanding I have to work on the kernel files to either change wifi drivers or ram/rom ones however I can't find a guide on the later. I only found a guide on the wifi.
Can anyone tell me how I can change the ram/rom files?
Or is anyone aware of a fitting custom rom I could use?
Hi,
I'm having big problem by low level format of my tablet RK3188(chip) have no idea of model is 10' one.
I'm looking to make a flashable img files from my backup CWM recovery to use with Android tool since my tablet is unknown
china with RK3188 chip.
Perhaps someone will give me idea to allocate proper parameter for recovery , kernel , boot , etc...
Usual location for tablet RK3188 Cortex A9 Quad core 1.6 ghz Governor interactive, Kernel 3.0.36+ ,Board hardware RK30Board/ 0000, Android 4.2.2 ;eng.root 20130912.185132 sdk 17, Display 1280x800; dpi;160 size 9.4'
GPU:Mali-400MP, RAM: 2048 Flash:32 gb Build in:16gb actual, wifi, usb, Bluetooth gps= all yes, camer 5MP additional 1.9MP
Recovery, system, boot, kernel are large files in cwm I need to make them smaller (proper size) to use with Android tool. Please correct me if I'm wrong and tell me if its possible or any other way to get to my CWM .I just need to get to recovery. Please help.
Many thanks for your time.
styropian said:
Hi,
I'm having big problem by low level format of my tablet RK3188(chip) have no idea of model is 10' one.
I'm looking to make a flashable img files from my backup CWM recovery to use with Android tool since my tablet is unknown
china with RK3188 chip.
Perhaps someone will give me idea to allocate proper parameter for recovery , kernel , boot , etc...
Usual location for tablet RK3188 Cortex A9 Quad core 1.6 ghz Governor interactive, Kernel 3.0.36+ ,Board hardware RK30Board/ 0000, Android 4.2.2 ;eng.root 20130912.185132 sdk 17, Display 1280x800; dpi;160 size 9.4'
GPU:Mali-400MP, RAM: 2048 Flash:32 gb Build in:16gb actual, wifi, usb, Bluetooth gps= all yes, camer 5MP additional 1.9MP
Recovery, system, boot, kernel are large files in cwm I need to make them smaller (proper size) to use with Android tool. Please correct me if I'm wrong and tell me if its possible or any other way to get to my CWM .I just need to get to recovery. Please help.
Many thanks for your time.
Click to expand...
Click to collapse
Update __
RK3188 adb is running no screen__help PLEASE
After erasing IDB in my unknown china tablet and loosing my whole system I was able to load different custom firmware from Chuwi v88 + different kernel and my Tab popup in windows showing 2 extra drives F and G.I did open android studio and notice access to adb and all activity in my android.The RKandroidTool also recognizing my tab.
No reaction to power button only automatically connecting to my comp ( black screen on my tab).
I have original CWM backup of my device.
Can someone advise me how to access recovery from this point or find the way to completely start my tablet.Maybe is possible to recover CWM from adb?I will need some help to use a proper commands perhaps in adb.
I have this friends tablet for a week or two.
I found, i think, right firmware, and that's one problem solved, i hope.
The other problem is, i got this tablet along with the flashing problem. I think SP flashing tool was used, but with a wrong firmware, and now is preloader messed up... (sry for my bad english)
Name of the tablet: Xwave Xpad 3G-701
Now, my problem is that i can't access anything, tablet just won't strat, computer can't recognize it, and so on, dead in other words.
specs:
OS: Android 4.2 Jelly Bean
GPU: Mali 400 MP, 3D OpenGL (ES 2.0)
Screen: 7 inch, 1024x600
Processor: 1.3Ghz Dual-Core ARM Cortex-A7 (MediaTek MT8312)
Ram: 512MB DDR2
Memory: 4GB
Motherboard is: ELINK_MR706_D3_V6 20140114
To avoid any forum rules problem, i added only dropbox link paths off the images... so i could explain my USB issue.
dropbox.com/s/4yhbbmbdc9z8gds/DSC_0115.JPG?dl=0 -- phone
dropbox.com/s/qefe24v4l6o96pj/DSC_0117.JPG?dl=0 -- motherboard
Computer can't recognize it, i tried many variants, it's just not working.
In motherboard picture, whole surface is covered with protection, only some ponits are accesible.
My question is, what is the procedure to unbrick this tablet particularly... to force the right preloader in it, and become recognisable by computer? The rest might be familiar to me.
Is it required to detach battery, as some procedures suggest...?
My apology if this is somewhere else asked, i just couldn't find ant explanation for this model.
If my question is unclear, i'll add any info or change needed....