Related
Hello everyone,
I'm a newbie, but a fairly tech-savvy newbie. I recently upgraded to a Mogul ( from a Treo 650 ) and after a bit of prevaricating, decided to upgrade the ROM. I've been researching all over this forum and PPCGeeks ( when they're up, at least ) and thought I had everything worked out about exactly what to do.
0 ) I wrote down the MSID, MDN, A-Key, and ran a program called GetSPC.
1 ) I unlocked the phone ( Olipro 2.40 )
2 ) I flashed the rom to DCD 2.2.6
briefly got stuck here, until I figured I needed to reset the phone to get back into the bootloader screen
3 ) I flashed the new radio.
4 ) After a bit of experimenting, I decided to try NeuROM, as it had more goodies on it. The .rar only had a single program, a .nbh file. ( unlike the DCD with the ROMupdateUtility.exe ) Further research led me to believe that I could move the .nbh file onto a Fat32 formatted microSD card and reset, and it would flash that rom. It seemed to work.
Now I have full access to everything, but the phone will not dial or anything. I typed in ##778# and tried to hit 'edit' and it pops up a screen demanding an unlock code, which I assumed was the six digit code I got from step 0, running GetSPC. That code doesn't work at all. Have I done something terribly wrong? Should I have not installed NeuROM with the microSD? I'm about to try to restore everything to factory settings and perhaps try again, but I'd really like to know where I went wrong. Any ideas? Thank you all for your great work here, and I appreciate any help you can provide.
when you ran GetSPC did you type in the ESN of your phone making sure to capitalize the letters? Try and run it again capitalizing the letters and make sure you type in the ESN exact.
Your issue could be that when you entered your hex code into GetSPC you did not capitalize, it will change the code.
guess I am late...
Wow, thanks for the very prompt response. I do believe that I did not capitalize the Hexadecimal number. I will try that.
EDIT
Yep, that did the trick. Thank you so much for your quick replies. Sheesh, Monday night and I get three replies within three minutes of posting. Ok, memo to myself; Hex code must always be capitalized.
hey... quick qustion do you have the 6 digit code needed for the epst code for the htc touch 6900
jenny_812 said:
hey... quick qustion do you have the 6 digit code needed for the epst code for the htc touch 6900
Click to expand...
Click to collapse
There is'nt one 6 digit code for every phone, each phone has it's unique 6 digit code.
Maybe I'm thinking of something different, but it was my understanding that the EPST unlock code was 000000 for everyone (unless changed through QPST or something).
Depends on your carrier. Verizon and Cellcom (small carrier I am with) use 000000. Sprint uses a piece of software (GetSPL) that generates a random 6 digit MSL code based on your phone's ESN. That is why sprint users need GetSPL. I am not sure of other carriers. We should start a thread that looks like the following....
MSL Unlock Code
Verizon = 000000
Cellcom = 000000
Sprint = (Use GetSPL)
Alltel = ??????
AT&T = ??????
Feel free to fill in the blanks if you are with these (or other carriers)
Ok, thank you for clearing that up. I'm on US Cellular and its 000000.
i always use the registry setting/log file method to get the SPC codes, since GetSPC hasn't ever worked for me. do a search for it on this site; it's easy
mine is a Quest XV6800 and it was locked with a random six digit code
Try a program call "baf msl grabber" worked great on my Qwest mogul
jjohnzon said:
Try a program call "baf msl grabber" worked great on my Qwest mogul
Click to expand...
Click to collapse
now he tells me...
programing my HTC Pro
I put in the ##778# and press edit now its asking me for a code...I got my phone flashed again to metro and that still didnt reset ...I tried calling sprint and asking them for the reprograming code... but they asking me for my acct.#.....Um dont have one with them......
any tips???
Thanks
EPST Code for Samsung SCH-i760
Does anyone know how to get an EPST Code for a Samusung SCH-i760...I fully flashed it to cricket and cant get my internet or pic messaging working cuz I cant program the phone...Can anyone help me...
If it is a verizon phone it should be 000000
this is how i got my code, using the ATDbg0.log file:
http://forum.ppcgeeks.com/showthread.php?p=523161
then i used CDMA Workshop to write the SPC/MSL to 000000. i got that program from a forum somewhere, just Google for it
Hi guys,
I used the tools which is attached. I found it in another website. Probably someone share it before. (NET CF must be installed)
Anyway it works great, it gave an unlock code even my ESN was 0000000.
Good luck!
Before I flashed to DCD's 2.1.0 I got all the information I needed - ESN, MSID, MSL etc etc. I've been looking into PRL-related edits lately but keep running into a problem.. Whenever it asks me to type in my MSL # it says that it's incorrect.
Any ideas?
If you used GetSPC to get your MSL, the alpha characters of your hex ESN have to be capitalized.
more info needed
Did the msl work before ??? what carrier ???? Sprint needs msl, Verizon, Alltel is 000000 for all phones.
IM trying to flash to cricket. already rooted and has the Eclipse Rom.
i got to change the SPC in CDMA WS 2.7 and i confirmed that. i know to flash it you cant read from QPST so i didnt and just filled oout the write spots. In QPST when i click write it just tells me ERROR SPC_CHANGE_ENABLE_I. Or the error PPP Password something.
i tried writing the NV files with CDMA WS but no matter what i do with cdma workshop it now says "PHONE ASK FOR SPC. SPC(6 digits) required.
ANy help would be appreciated...thanks
000000 is spc code. type that in spc field of cdma workshop before write to nv
Sent from my DROID RAZR using xda premium
yea i already know that. i found out what i was doing. using CDMA WS i was going to the SPC spot and writing it then trying to do the stuff. figured out i needed to just SEND the unlock to the phone in order to write items to the phone.
Phone is flashed over now.
have a samsung galaxy s4 i545 on 4.3 was working fine,was in the service menu in servicemode menu cdma/control/msl edit
was looking had a 7 digit number in it but after i rebooted phone now the spc won't take the 6 zero's any way to fix? just spc don't work now password for phone works,but can't program it without spc.
nevermind figurered it out good thing has built in backup
hi I have a samsung note 3 sprint 4.4.2 NC5 modem
I need help to change my note 3 spc to 000000 so i can unlock it for use it to another cdma provider .
I have the spc and samsung password which is 2012112120131219
and use this on cmd :
00
4B13030000000000
4B130F006E766D2F6E756D2F383500
4B1308006E766D2F6E756D2F383500
4B13020041020000B60100006E766D2F6E756D2F383500
4B1305000000000000000000303030303030
4B13030000000000
I use dfs program to change the spc to 000000 as always but this note 3 spc does not change even after flash it.
should i change the modem ? or there is another way
thank you
sobri46 said:
hi I have a samsung note 3 sprint 4.4.2 NC5 modem
I need help to change my note 3 spc to 000000 so i can unlock it for use it to another cdma provider .
I have the spc and samsung password which is 2012112120131219
and use this on cmd :
00
4B13030000000000
4B130F006E766D2F6E756D2F383500
4B1308006E766D2F6E756D2F383500
4B13020041020000B60100006E766D2F6E756D2F383500
4B1305000000000000000000303030303030
4B13030000000000
I use dfs program to change the spc to 000000 as always but this note 3 spc does not change even after flash it.
should i change the modem ? or there is another way
thank you
Click to expand...
Click to collapse
That's the AT commands (or is it GOBI...) to set the SPC to 000000 for the S3. NEVER send commands to a different model. You have no clue what effect it'll have.
To flash to another carrier you don't need to reset the SPC. Just use the app to get your SPC and flash it as you normally would.
Sent from my SPH-L720 using XDA Free mobile app
This code is use on CMD on DFS and it is not especially for s3.
I flashed my S4 Sprint also using this method and changed the spc to 000000 and everything is good .
By the way I discovered yesterday how to change the spc to 000000 for the note 3 sprint .
thank you for your reply , I really appreciate it
Not too sure why you'd blindly use modem commands to reset the SPC (other than when we didn't have this new tool which was months ago). I prefer to use the MSL tool. It only reads it from the device, so there's no dirty hacking involved. Just my .02
Sent from my SPH-L720 using XDA Free mobile app
It doesnt help anyone if you dont post the working method.
On nc5d this worked for me: open USBSettings and select DM+MODEM+ADB (you can use my script here to access the menu http://forum.xda-developers.com/showthread.php?t=2785328 )
Reboot phone
In DFS send your spc and password 2012112120131219
In programming tab type 000000 in SPC field and click write
click reset and wait for phone to reboot (new spc wont stick if you skip this step)
Enjoy your changed spc/msl code.
idone said:
It doesnt help anyone if you dont post the working method.
On nc5d this worked for me: open USBSettings and select DM+MODEM+ADB (you can use my script here to access the menu http://forum.xda-developers.com/showthread.php?t=2785328 )
Reboot phone
In DFS send your spc and password 2012112120131219
In programming tab type 000000 in SPC field and click write
click reset and wait for phone to reboot (new spc wont stick if you skip this step)
Enjoy your changed spc/msl code.
Click to expand...
Click to collapse
The SPC/MSL utility tool is all over the internet. I didn't think I'd have to post a link to it...
Sent from my SPH-L720 using XDA Free mobile app
ecs87 said:
The SPC/MSL utility tool is all over the internet. I didn't think I'd have to post a link to it...
Sent from my SPH-L720 using XDA Free mobile app
Click to expand...
Click to collapse
Sorry I dont find any tool to change it. Google only seems to find me apps to read spc not write a new one.
****edit****
and my post wasnt directed to you it was to the op who posted a question and then said he found the answer but didnt share it for others who might find this thread.
But now that you mention it please do link to the app that can write spc to 000000
idone said:
Sorry I dont find any tool to change it. Google only seems to find me apps to read spc not write a new one.
****edit****
and my post wasnt directed to you it was to the op who posted a question and then said he found the answer but didnt share it for others who might find this thread.
But now that you mention it please do link to the app that can write spc to 000000
Click to expand...
Click to collapse
Ohhh! Yeah, I don't know of an app to write the spc, only read. I don't really find the need to write the SPC just as long as I can read it to send it.
Sent from my SPH-L720 using XDA Free mobile app
sobri46 said:
This code is use on CMD on DFS and it is not especially for s3.
I flashed my S4 Sprint also using this method and changed the spc to 000000 and everything is good .
By the way I discovered yesterday how to change the spc to 000000 for the note 3 sprint .
thank you for your reply , I really appreciate it
Click to expand...
Click to collapse
@sobri46, It is highly appreciated if you could share this method with us.
jodhaaa said:
@sobri46, It is highly appreciated if you could share this method with us.
Click to expand...
Click to collapse
##diag# will also get you to the usb settings, or my GalaxyTools app in the app subforum.
idone said:
It doesnt help anyone if you dont post the working method.
On nc5d this worked for me: open USBSettings and select DM+MODEM+ADB (you can use my script here to access the menu http://forum.xda-developers.com/showthread.php?t=2785328 )
Reboot phone
In DFS send your spc and password 2012112120131219
In programming tab type 000000 in SPC field and click write
click reset and wait for phone to reboot (new spc wont stick if you skip this step)
Enjoy your changed spc/msl code.
Click to expand...
Click to collapse
Sorry for my late reply
Hi the method is look like the s3 and s4 unlocking mode
First you should downgrade the modem to MI3 modem
Then go to diag mode choose dm+modem+adb
Install the app msl utility.apk to know your mobile spc
Then using dfs . Put your mobile spc and click write
And then put the sprint password and click write
Then the last thing you should go to change your spc to 000000 on the dfs
Note. I found sometimes when i change the spc to 000000 it didnt stick on the first try. Sometimes i need 5 times to let the new spc to be stick with the mobile
And check using the msl utility.apk if your spc is 000000 it means you are success to unlock the mobile.
If you click on reset in dfs after writing spc you won't have to do it 5 times for it to stick.
---------- Post added at 09:00 PM ---------- Previous post was at 08:52 PM ----------
And DON'T go downgrading your modem to do this. It is not necessary at all.
I just tested and the change sticks first try on NH7 newest software/baseband.
Just send spc and pwd first and everything will be fine.
i changed my spc to 222222 i have 4.4.2 but it does not change anything,
Sent from my One X using XDA Premium 4 mobile app
I have the S4 Sprint
sobri46 said:
This code is use on CMD on DFS and it is not especially for s3.
I flashed my S4 Sprint also using this method and changed the spc to 000000 and everything is good .
By the way I discovered yesterday how to change the spc to 000000 for the note 3 sprint .
thank you for your reply , I really appreciate it
Click to expand...
Click to collapse
please explain better , how i will change my S4 Sprint . you changes yours but i am having hard time change mine . this issue of command is what i don't understand. how to write and everything .
thanks
can it work in s4
please what dfs fll meaning and link??
I have the spc and samsung password which is 2012112120131219
Click to expand...
Click to collapse
Work on Samsung Galaxy Tab 4 SM-237P with DFS Cdma tool I change SPC to 000000.