Well, I have a d2pad SN 201301 on the back so its somewhat new
It uses rk2829 rockchip.
Anyways Ive been trying to get recovery on it for the past couple hours to use a new rom, finally got recovery working, did everything installed my rom, and let it restart.
Well, The rom isnt compatible, there was a later version a few pages into the thread that might have been, but the one I got wasnt.
So now I'm stuck, at the intro d2 logo
I only have 1 button and it is power.
Ive tried to get adb working, because it at least says its connected, but with no success anyone have any ideas?
wzzupp548 said:
Well, I have a d2pad SN 201301 on the back so its somewhat new
It uses rk2829 rockchip.
Anyways Ive been trying to get recovery on it for the past couple hours to use a new rom, finally got recovery working, did everything installed my rom, and let it restart.
Well, The rom isnt compatible, there was a later version a few pages into the thread that might have been, but the one I got wasnt.
So now I'm stuck, at the intro d2 logo
I only have 1 button and it is power.
Ive tried to get adb working, because it at least says its connected, but with no success anyone have any ideas?
Click to expand...
Click to collapse
Hey, I realize that it's been a couple years since you posted this question. I never saw any responses. So how did it all end?
Also, there was one critical piece of information you failed to share with the XDA community...you said you worked on getting into recovery with a device that only had a power button and no volume buttons. May I ask how on earth you managed to get into recovery using only a power button? Reason I ask is that I am now facing this situation. NTech Alexis RX3HD8 tablet, rockchip RK2928 processor, power button and no volume buttons! I need to get into recovery but I cannot turn on USB debugging (and the tablet is pattern locked but the pattern was entered too many times....so I am locked out).
At this point, if I cannot enter recovery mode, the tablet is a permanently soft-bricked which is, for all intents and purposes, the same as a hard-brick.
I think what happened for me was, wanted to install new rom, got into recovery to install it, then it bricked my tab, after that I was at the logo
in my case i fixed everything by getting a rkflasher, to reinstall it, and contacting support for the factory image, which is lucky they new something about it, some companies abandon support, or dont know enoguh about what they sell, lol
as for your situation
these are the things i'd try
1. If it has google play, and is connected wifi even if its locked you can try this page
https://www.google.com/android/devicemanager
and then pick ur device and factory reset it is an option (although ive never tried it)
2. search around on the internet for 1 button recovery methods, I've seen quite a few weird tablets, and some I can think of with 1 button recovery
A. a pin hole thats not the reset button or the mic, was an actual button, and that was used to get into recovery with a safety pin, and doing the normal holding it while powering on method
B.. holding the power button, and instead of letting go when u see a logo, keep holding it, till it shuts off again, then power it on
C. plug it in to pc via usb, and turn it on, while its booting, see if ur pc recognizes it at any point during the startup and try to run some commands, ive had a brand of tabs, that give u adb access during boot, but then remove it after finished booting
4. their website is in spanish, and they dont have firmware/manual links available for your tablet
You could contact support for recovery instructions or reflash instructions,, and hope they speak english or you speak Spanish
Most of the time with 1 button tablets, if theirs no info of similar ones online, unless you can contact support, you might be out of luck
PS, my edit:
also, I saw ur post on the youtube video while looking up stuff about this tablet, if that guy can get you a firmware, you have another option of trying to get to download mode too
my tablet, with rk2928 uses these instructions to get it to show up in the RKBatchTool.
https://www.d2pad.info/docs/OSFirmwareInstallInstruction_D2-721.pdf
maybe they can help you get into download mode on urs
all of this being said, I hope my first suggestion will work, IDK if wifi is disabled during pattern lock, or if u can factory reset any tablet, I just know I always see that option when I'm using it to find my devices ect.
CVAngelo said:
Hey, I realize that it's been a couple years since you posted this question. I never saw any responses. So how did it all end?
Also, there was one critical piece of information you failed to share with the XDA community...you said you worked on getting into recovery with a device that only had a power button and no volume buttons. May I ask how on earth you managed to get into recovery using only a power button? Reason I ask is that I am now facing this situation. NTech Alexis RX3HD8 tablet, rockchip RK2928 processor, power button and no volume buttons! I need to get into recovery but I cannot turn on USB debugging (and the tablet is pattern locked but the pattern was entered too many times....so I am locked out).
At this point, if I cannot enter recovery mode, the tablet is a permanently soft-bricked which is, for all intents and purposes, the same as a hard-brick.
Click to expand...
Click to collapse
Without ADB a soft-brick can become permanent state!
wzzupp548 said:
I think what happened for me was, wanted to install new rom, got into recovery to install it, then it bricked my tab, after that I was at the logo
in my case i fixed everything by getting a rkflasher, to reinstall it, and contacting support for the factory image, which is lucky they new something about it, some companies abandon support, or dont know enoguh about what they sell, lol
as for your situation
these are the things i'd try
1. If it has google play, and is connected wifi even if its locked you can try this page
https://www.google.com/android/devicemanager
and then pick ur device and factory reset it is an option (although ive never tried it)
2. search around on the internet for 1 button recovery methods, I've seen quite a few weird tablets, and some I can think of with 1 button recovery
A. a pin hole thats not the reset button or the mic, was an actual button, and that was used to get into recovery with a safety pin, and doing the normal holding it while powering on method
B.. holding the power button, and instead of letting go when u see a logo, keep holding it, till it shuts off again, then power it on
C. plug it in to pc via usb, and turn it on, while its booting, see if ur pc recognizes it at any point during the startup and try to run some commands, ive had a brand of tabs, that give u adb access during boot, but then remove it after finished booting
4. their website is in spanish, and they dont have firmware/manual links available for your tablet
You could contact support for recovery instructions or reflash instructions,, and hope they speak english or you speak Spanish
Most of the time with 1 button tablets, if theirs no info of similar ones online, unless you can contact support, you might be out of luck
PS, my edit:
also, I saw ur post on the youtube video while looking up stuff about this tablet, if that guy can get you a firmware, you have another option of trying to get to download mode too
my tablet, with rk2928 uses these instructions to get it to show up in the RKBatchTool.
https://www.d2pad.info/docs/OSFirmwareInstallInstruction_D2-721.pdf
maybe they can help you get into download mode on urs
all of this being said, I hope my first suggestion will work, IDK if wifi is disabled during pattern lock, or if u can factory reset any tablet, I just know I always see that option when I'm using it to find my devices ect.
Click to expand...
Click to collapse
Hey thanks for getting back to me. You've been extremely helpful and your response may hopefully be found in future by others who have the same problem.
Here's how it's working out for me with this device:
1. It has Google Play but unfortunately the wifi is turned off and there's no way to connect. But in any event, the little kid whose tablet it is (I'm working on the tablet at the request of her father who is my friend), she doesn't remember the Gmail account name or password.
2. I've searched the entire Internet (LOL) including Spanish and Chinese websites/videos but no luck. I can't find anything about putting this badboy into recovery. The reset button is just for show...it only turns the tablet off in case the power button is unresponsive.
3. I've been to the website of "manufacturer". It's a Portuguese company (I speak the language) but they haven't responded to any contact requests. And they appear to offer the firmware for the devices but download link is dead. So I cannot even get the firmware to flash it. The dude on YouTube has not sent me any link to firmware.
But the bigger problem and the key to the issue is that I cannot get the tablet to be recognized by the computer no matter what I've tried. I've tried all kinds of combinations of power button play but I never get that satisfying BEEP that indicates that there is a connection open. You see, I have the drivers for the tablet but there is no way to install them without the tablet giving the opening (even if it would come back as Unknown Device). So, I'm crap out of luck with this soft-brick.
Again, thanks for your help. After 3 days and probably 15 hours spent trying to reset this thing, I'm going to have to throw in the towel. Important lessons learned:
#1. NEVER PURCHASE AN ANDROID DEVICE THAT HAS NO VOLUME KEYS (or without knowing how to get into recovery). You're only asking for trouble if anything should go wrong. And believe me, this is the THIRD TIME I've seen a device that cannot go into recovery. In one case, I was able to flash new firmware directly on bootup off the external SD card (it was an Android laptop with WM8505 chip). I guess one out of three ain't bad odds...but they are not the kind of odds you want with expensive devices.
#2. ALWAYS TURN ON USB DEBUGGING WITH ANY ANDROID DEVICE YOU OWN AND TELL YOUR FRIENDS TO DO THE SAME. One day, it may end up being the savior of the life of that device because it usually means you can access the device via ADB in case of a soft-brick. LOL.
CVAngelo said:
Hey thanks for getting back to me. You've been extremely helpful and your response may hopefully be found in future by others who have the same problem.
Here's how it's working out for me with this device:
1. It has Google Play but unfortunately the wifi is turned off and there's no way to connect. But in any event, the little kid whose tablet it is (I'm working on the tablet at the request of her father who is my friend), she doesn't remember the Gmail account name or password.
2. I've searched the entire Internet (LOL) including Spanish and Chinese websites/videos but no luck. I can't find anything about putting this badboy into recovery. The reset button is just for show...it only turns the tablet off in case the power button is unresponsive.
3. I've been to the website of "manufacturer". It's a Portuguese company (I speak the language) but they haven't responded to any contact requests. And they appear to offer the firmware for the devices but download link is dead. So I cannot even get the firmware to flash it. The dude on YouTube has not sent me any link to firmware.
But the bigger problem and the key to the issue is that I cannot get the tablet to be recognized by the computer no matter what I've tried. I've tried all kinds of combinations of power button play but I never get that satisfying BEEP that indicates that there is a connection open. You see, I have the drivers for the tablet but there is no way to install them without the tablet giving the opening (even if it would come back as Unknown Device). So, I'm crap out of luck with this soft-brick.
Again, thanks for your help. After 3 days and probably 15 hours spent trying to reset this thing, I'm going to have to throw in the towel. Important lessons learned:
#1. NEVER PURCHASE AN ANDROID DEVICE THAT HAS NO VOLUME KEYS (or without knowing how to get into recovery). You're only asking for trouble if anything should go wrong. And believe me, this is the THIRD TIME I've seen a device that cannot go into recovery. In one case, I was able to flash new firmware directly on bootup off the external SD card (it was an Android laptop with WM8505 chip). I guess one out of three ain't bad odds...but they are not the kind of odds you want with expensive devices.
#2. ALWAYS TURN ON USB DEBUGGING WITH ANY ANDROID DEVICE YOU OWN AND TELL YOUR FRIENDS TO DO THE SAME. One day, it may end up being the savior of the life of that device because it usually means you can access the device via ADB in case of a soft-brick. LOL.
Click to expand...
Click to collapse
At last, did we find at last how to enter in recovery mode if there is only one button (power). I am in the same situation with @CVAngelo .Is it possible not to exist recovery mode at all? My tablet is BENEVE R708G with Rockchip RK2928. I tried every combination with power button and reset button but no luck at all.I have boot loop after trying to change the bootanimation.The weird thing is that the new boot animation ''works'' but after that it goes on boot loop forever.
Hi,
can I help me with my 7-inch tablet Miia.
The tablet starts at power, but remaining Blocked on Android screen and does not proceed further. I tried to go into recovery to perform a hard reset, but once you're with the volume buttons do not allow me to make no choice and no other key permits. I checked the inside of the tablet and everything seems ok, the welds of the keys are fine.
I read about flash rom etc etc, but on the net I find only a lot of info and no solution optimal.
Trying then I found your forum and I see it very reliable, so I decided to enter in your community.
I would like to know if there is a way to restore the tablet from PC ... also wanting ... or with the rom or another ...
Thanks first to who will read my question and who decides to help me out .
Sorry for my english.
Bye !!!!
Hi guys, sorry if I posted this at the wrong place.
I have a Lenovo s860 and it went into a bootloop. It was stock and all so I thought that I can have my files recovered if I just bring it to a service center so they can get the files first before wiping it or maybe even fixing the bootloop without wiping the device. Well, the thing is, the guy at the service center screwed up and now, when I try to turn it on, I still see the boot screen (Lenovo, powered by Android) but the next screen is like an television with bad signal.
I'm familiar with rooting and flashing ROMs, I've tried it on my Galaxy S2 (yeah I know, it was way back), but I think things are still more or less the same: I need to be able to boot into recovery mode in order to root the device. However, when I tried the Power Button + Volume Up, or any combinations of the Power Button and the Volume Buttons, it just goes straight to the dead screen, I get no response whatsoever.
I also tried to check if adb can detect it, however, it didn't seem to be able to do so. I'm using a MacBook Pro so I know I don't have to install any drivers, I also code Android Apps so I have a background on this.
I think my only option would be to flash the ROM on this dead device but I don't know how to do that. I've also seen some posts that suggest doing some things (I forgot the specifics) while the battery is drained, so what I'm doing for the mean time is to leave the phone open and let it drain which might take ~2 days.
Does anyone know how to flash a ROM on a bricked device? Thanks for any leads.
hey guys,
i'm having hard time to find out how exactly to flash my old oem tablet and i really dont expect anyone here to search anything about it(i do that...), just to guide me in general please.
i just found this old tablet and thought i could try to use it as a touchscreen-mp3 player connected to my amplifier...
i charged it and powered it but stuck on "android" logo, i tried many key combinations to put it to recovery mode but i just couldnt find it i guess.
then i started searching of how to flash it...
what is visible from outside is "f&u ETB7405" which brings almost nothing(it's just an oem model) so i opened to see inside where i can see one chip "allwinner a13" and "tzx-q8 713B 6".
it has 7" screen.
based on these i finally found a fimware (using PhoenixCard) that boots normally BUT i get no touchscreen or wifi working. i can connect a usb mouse and have access to it.
do i also have to flash any extra firmware/driver for just the touchscreen or wifi?
what is the most important characteristic("A13" or "TZX-Q8...") to concentrate my search for?
why is it so fcn difficult to find a working firmware???
in case anyone else is having the same issues and hopelessly tries to find the firmware for his device and bumps in unanswered posts or dead links, guys just try different "A13" firmware! Although i'm not really sure that it even has to be "A13"!
i was trying to find firmware with the most of my specs on its name like f.e. "A13-TZX-Q8-713B6" but the paradox happened. the most similar firmware names were not good and i tried a lot! instead i finally decided to just search for "A13" firmware and try any of them one by one despite the names. that was it! i have already found a couple!
from here: ww.androidtablets.net/threads/firmware-based-on-allwinner-a13-roms.72449
a13-TJ P860-V7.1-gsl1680-MID-756-V4.2-20130823-test-keys.zip
all works but there is only "english" and "thai" in keyboard languages.
A13_TWD_MID-gslX680-800X480_20130423 test-keys.rar
all works but touch screen "mirrored" sideways!
good luck to you guys!
thanks