My nextbook next2 turns on then gets to the abraham lincoln screen and keeps rebooting the abraham lincoln screen. When i try to get into recovery mode my pc makes 3 beeps and nothing happens. i looked in the device manager and it shows unknown device but it cannot find the drivers and the next 2 does not light up with any screen. I dled the rkbatchtool 1.3 and the device does not show up in it.
My question is? Is my nextbook fried or can i get into recovery mode another way? Or does anyone have any ideas?
i fixed it
gunz1 said:
My nextbook next2 turns on then gets to the abraham lincoln screen and keeps rebooting the abraham lincoln screen. When i try to get into recovery mode my pc makes 3 beeps and nothing happens. i looked in the device manager and it shows unknown device but it cannot find the drivers and the next 2 does not light up with any screen. I dled the rkbatchtool 1.3 and the device does not show up in it.
My question is? Is my nextbook fried or can i get into recovery mode another way? Or does anyone have any ideas?
Click to expand...
Click to collapse
First off i have win 7 pro 32 bit
i dled RK2818 Android Upgrade Tool_v1.23 googled
I added the driver from this in device manager to unknown device it found rockusb device
i dled _NEXTBOOK 2 ROM ONLY_____________________________________
special thanks to delimeat52
first post of the next2 closed thread
i followed directions and pushed on right side arrow while plugging in usb to pc finally RKAndroidBatchUpgrade first number 1 appeared green and i updated to the nextbook 2 rom image file good luck
My Pc will not find the device via usb though, atleast its working can do stuff with the sd card now and explorer
my pantech sky vega a760s got soft bricked
here's what happened:
-the phone won't open unless connected to pc
-when connected, it will only go to charging mode
-when i try to enter recovery mode, this shows up:
"your phone will restart due to error occurred while running application "
i cannot access recovery mode, the only thing i can access is the s/w upgrade mode, which i don't know how to use since i'm not korean
and i can't understand pantech's website.
also, when i enter in fastboot mode, all drivers are installed except for a driver named "Android" which is too general for me to manual search (inlcuded an image attachment of the failed driver)
How can I unbrick my phone?
PLEASE HELP. THANK YOU IN ADVANCE.
same here..
same here my sky vega a760 stock on boot image anyone can help plsss how can i revive this..plsssss.
joekap said:
same here my sky vega a760 stock on boot image anyone can help plsss how can i revive this..plsssss.
Click to expand...
Click to collapse
You should re-install new room stook via home page iVeGa:good:
Re: Help..
tnx for the reply but how can i reinstall i dont know where to donwload and i cant understand in korean site.. plsss send me working rom for A760s plsss...tnx
[TUT]Recovery Mode Sky Vega Racer IM-A760S/A770K
joekap said:
tnx for the reply but how can i reinstall i dont know where to donwload and i cant understand in korean site.. plsss send me working rom for A760s plsss...tnx
Click to expand...
Click to collapse
To go into Soft/Ware download mode
1. Turn of phone
2. Simultaneously press: VOLUME UP + MENU + POWER
3. S/W Upgrading will now flash on the screen
To upgrade firmware back to version 1.47, you first need to have the UniUSBdriver installed on your computer.
4. After you have installed the driver, test your phone’s connection to the computer to initially determine all the required drivers were installed properly (this is while your phone is in S/W download mode). But before doing this, make sure that you have activated USB DEBUGGING on your phone.
Code:
>settings
>applications
>development
>usb debugging (must be checked)
5. Using Microsoft Internet Explorer v8 or v9, proceed to this page:
-------------->>> dmfile.isky.co.kr/NewSelfUpgrade/index.html?userid=&hpno
Notice when that page opens, it will prompt you to install ACTIVE X. Allow that installation to proceed.
6. After ACTIVE X has been installed, notice on the left side there is a something like loading prompt. Wait until it gets into blue bar with arrow up phrase noting USB with some Korean characters. Then boot to S/W mode your phone and plug it to your compurer then click the blue bar with arrow up.
7. Clicking the Blue bar with arrow up will turn it into a progressing bar. Notice the characters on top of the progress bar may change and at this point there is communication between the phone and the Sky download site. It may take a few minutes for the phone to establish a download connection between Sky’s services. Once a connection is established, the characters above the progress bar will turn into a progressing percentage bar starting from 1% and ending into 100%.
There will be two phases of the progressing percentage bar. The first phase is downloading the software while the second is loading the v1.47 software into the phone. After the 2nd phase, the phone will automatically reboot. The first phase will depend who slow or fast your internet connection is.
:fingers-crossed: Goodluck :fingers-crossed:
clearlangpo said:
To go into Soft/Ware download mode
1. Turn of phone
2. Simultaneously press: VOLUME UP + MENU + POWER
3. S/W Upgrading will now flash on the screen
To upgrade firmware back to version 1.47, you first need to have the UniUSBdriver installed on your computer.
4. After you have installed the driver, test your phone’s connection to the computer to initially determine all the required drivers were installed properly (this is while your phone is in S/W download mode). But before doing this, make sure that you have activated USB DEBUGGING on your phone.
Code:
>settings
>applications
>development
>usb debugging (must be checked)
5. Using Microsoft Internet Explorer v8 or v9, proceed to this page:
-------------->>> dmfile.isky.co.kr/NewSelfUpgrade/index.html?userid=&hpno
Notice when that page opens, it will prompt you to install ACTIVE X. Allow that installation to proceed.
6. After ACTIVE X has been installed, notice on the left side there is a something like loading prompt. Wait until it gets into blue bar with arrow up phrase noting USB with some Korean characters. Then boot to S/W mode your phone and plug it to your compurer then click the blue bar with arrow up.
7. Clicking the Blue bar with arrow up will turn it into a progressing bar. Notice the characters on top of the progress bar may change and at this point there is communication between the phone and the Sky download site. It may take a few minutes for the phone to establish a download connection between Sky’s services. Once a connection is established, the characters above the progress bar will turn into a progressing percentage bar starting from 1% and ending into 100%.
There will be two phases of the progressing percentage bar. The first phase is downloading the software while the second is loading the v1.47 software into the phone. After the 2nd phase, the phone will automatically reboot. The first phase will depend who slow or fast your internet connection is.
:fingers-crossed: Goodluck :fingers-crossed:
Click to expand...
Click to collapse
i need help. i just installed uniUSBdriver and it's successful. however, when i connect the phone there is one driver that is unable to install. the driver is just called "android" tried to look everywhere for a manual installer but the name of the driver is too vague to search. can you please help me with this one? it seems like the self upgrade site can't detect the phone without this driver installed.
Solution Soft brick, Android drivers in Fastboot
jimmygammi said:
i need help. i just installed uniUSBdriver and it's successful. however, when i connect the phone there is one driver that is unable to install. the driver is just called "android" tried to look everywhere for a manual installer but the name of the driver is too vague to search. can you please help me with this one? it seems like the self upgrade site can't detect the phone without this driver installed.
Click to expand...
Click to collapse
1. Connect your phone in Fastboot, and when your pc asks for 'Android' drivers, you need to install PDAnet, just google to download it.
2. then to Fastboot, and Install Recovery SWM v6 either normal or touch
3. Then go to Recovery and Install new stock/custom rom from SdCard.
thats all. :fingers-crossed:
bobby786pk said:
1. Connect your phone in Fastboot, and when your pc asks for 'Android' drivers, you need to install PDAnet, just google to download it.
2. then to Fastboot, and Install Recovery SWM v6 either normal or touch
3. Then go to Recovery and Install new stock/custom rom from SdCard.
thats all. :fingers-crossed:
Click to expand...
Click to collapse
can you post links where to get the recovery image and a link where to download roms? i'm trying to search but no luck. your help will be really appreciated. thank you very much :laugh:
stuck at s/w uploading
heeelp can anyone help me... my a760s dont turn on and if i plug a charger or into a pc the only thing that apears is "s/w uploading"
Did you fix it? results?
beakolang said:
heeelp can anyone help me... my a760s dont turn on and if i plug a charger or into a pc the only thing that apears is "s/w uploading"
Click to expand...
Click to collapse
Although its long enough for you to forget you once had Sky 760 but did you try the method posted by "clearlangpo"?
You phone reincarnated anyway?
clearlangpo said:
To go into Soft/Ware download mode
1. Turn of phone
2. Simultaneously press: VOLUME UP + MENU + POWER
3. S/W Upgrading will now flash on the screen
To upgrade firmware back to version 1.47, you first need to have the UniUSBdriver installed on your computer.
4. After you have installed the driver, test your phone’s connection to the computer to initially determine all the required drivers were installed properly (this is while your phone is in S/W download mode). But before doing this, make sure that you have activated USB DEBUGGING on your phone.
Code:
>settings
>applications
>development
>usb debugging (must be checked)
5. Using Microsoft Internet Explorer v8 or v9, proceed to this page:
-------------->>> dmfile.isky.co.kr/NewSelfUpgrade/index.html?userid=&hpno
Notice when that page opens, it will prompt you to install ACTIVE X. Allow that installation to proceed.
6. After ACTIVE X has been installed, notice on the left side there is a something like loading prompt. Wait until it gets into blue bar with arrow up phrase noting USB with some Korean characters. Then boot to S/W mode your phone and plug it to your compurer then click the blue bar with arrow up.
7. Clicking the Blue bar with arrow up will turn it into a progressing bar. Notice the characters on top of the progress bar may change and at this point there is communication between the phone and the Sky download site. It may take a few minutes for the phone to establish a download connection between Sky’s services. Once a connection is established, the characters above the progress bar will turn into a progressing percentage bar starting from 1% and ending into 100%.
There will be two phases of the progressing percentage bar. The first phase is downloading the software while the second is loading the v1.47 software into the phone. After the 2nd phase, the phone will automatically reboot. The first phase will depend who slow or fast your internet connection is.
:fingers-crossed: Goodluck :fingers-crossed:
Click to expand...
Click to collapse
Hello Hacker!
I am Zahid Gill and a software engineer by profession. Websites are my speciality. I love android and Korean phones. I have bricked/ unbricked fixed and patched many phone before (but only with XDA's help ) many
While flashing Sky vega 760s it stuck on some point. I waited long enough but thenI had to remove it and.... it was bricked.
I was still able to go to recovery, fastboot and bootloader. I tried wiping /system and others but cwm was not able to.
I tried flashing with offline flasher tool again but it went into red screen on bootloader, like here:
http://sphotos-g.ak.fbcdn.net/hphotos-ak-prn1/p206x206/26340_10200120329905648_1168156367_n.jpg
NOW, offline flashing stuck on 60%. I am unable to boot the phone in any other mode. Even putting on charging takes phone to this red s/w mode.
Are you able to help me with this? I shall be very thankful.
PS: I had stock ROM 4.1.2 originally updated with no custom tickling.
Did you find any solution
Hello I also stuck in same situation. My phone ima-760 got soft brick and red S/w upgrading only. Kindly help if any one has a solution.
Buddy
jimmygammi said:
my pantech sky vega a760s got soft bricked
here's what happened:
-the phone won't open unless connected to pc
-when connected, it will only go to charging mode
-when i try to enter recovery mode, this shows up:
"your phone will restart due to error occurred while running application "
i cannot access recovery mode, the only thing i can access is the s/w upgrade mode, which i don't know how to use since i'm not korean
and i can't understand pantech's website.
also, when i enter in fastboot mode, all drivers are installed except for a driver named "Android" which is too general for me to manual search (inlcuded an image attachment of the failed driver)
How can I unbrick my phone?
PLEASE HELP. THANK YOU IN ADVANCE.
Click to expand...
Click to collapse
I have the same problem but a lot of the answers are to re-install stock? Which part don't they understand...it's BRICKED ( and only shows the RED S/W Upgrading symbol) so it's impossible to Flash stock firmware in that state?
Just as the title says help please before leaving to work I flashed a kitkat rom to my phone (the htc one) usually when i flash roms everything goes well but this time it went bad and now i cant access recovery my phone is at an endless bootscreen and when i try connecting it to my pc my computer doesnt recognize it just a message saying error trying to read usb device
im running Windows 8.1
original usb cable that came with the phone
Hi , so i buy leagoo lead 1 from Etotalk they send me phone and everything was ok , but after 2 weeks i got OTA update which i download and click on apply , phone restart and start again instaling new update (i was like ok everything is good )but at middle of this update it give me Error Android icon with red color ,
and after that i can just start phone again and see just boot menu with :
otd leagoo lead1 sm619b v0.9.2_S1202
Normal Boot
Update via ADC
Update from sdcart
update from cashe
wipe cashe
wipe data (factory reset)
....(this one last i dont rememeber)
I tried wipe all and restart again but that did not help me much ..
ok so i download SP-flashtool from Leagoo web site instal all driver for usb and download Original rom from theyr site too .
what i did is i start program like admin. then i click on Option->be sure that Usb mode is enable then again Option -> DA Download All-> and enable Hight speed , after that i click on Scatter -loading and from the folder with Rom i sellect "MT6582_Android_scatter.txt"click on Firmware ->Upgrade and plug my phone which is turn off . in program i can see that he fount it but after 2 hour it is still at 0% how u can see on image i attach to this with some txt record from program with errors
So could anybody tell me what should i do now ?
try different (and newer) sp flashtool:
SP_Flash_Tool_v5.1348.00
https://drive.google.com/file/d/0BwtGwuP0GdfBZzh3a2NCWVZ3RVU/edit?pli=1
r0c0 said:
try different (and newer) sp flashtool:
SP_Flash_Tool_v5.1348.00
Click to expand...
Click to collapse
i will try but now i got another problem so i cant turn off my phone with usb cable plug in , i can see batery logo or i just turn it on * unlycky me but for half sec when phone was plug in with meadiatek preloader i saw it working for 1 secunde u can see on my printscreen
you need to plug in a usb cable and really fast press download button in flash tool, this helps with BROM errors. otherwise you could try googling the error or just contact leagoo.
r0c0 said:
you need to plug in a usb cable and really fast press download button in flash tool, this helps with BROM errors. otherwise you could try googling the error or just contact leagoo.
Click to expand...
Click to collapse
Yeah i try today and after some time i did it , i use official rom from web site , all file load dormat etc , then green cirle "OK" i unplug phone from usb and turn it on but i saw that logo "LEAGOO" was flickring and then top half display of mobile was Yellow and bottom was white/black thats maybe worst then before i emailing with seller too but i dont think he could help me
and after that with another try i waned use different rom i got this pic down .. so again im on connect disconect phone
after 10+ try i connect it again and trying another rom hope this will work :silly:
1st edit: add img after ok flash
2nd edit k phone after turn on is yellow at top and at bottom white black
should i use download only or try format all+ download
3th: i upload img of phone after start so u can see
its to bad that ppl from etotalk dont know how to deal with it too
i got the same problem
i was flashing lead 1 firmware on lead 1i
lead 1i is the latest so download right firmware..
Hello,
About a week ago my chinese tablet that i bought for about 50 $ broke .. first of all when i pressed the start up button it used to give me a white background with a Arko logo but now it gives me that but with some lines .. i dont know how to explain it there is a photo bellow.I have tryed to boot it up on the recovery but no luck .. now the weird thing is that when i connect it to my computer with a usb cable my pc(windows 10) makes the sound that a device has been connected but i cant see my phone .. it only says uknown device (install drivers) . Now i searched for the drivers but again no luck.. if u guys can help me please let me know...
images: h t t p ://imgur.com/a/HtZMo (take the spaces of )