I can't find any threads nor mention of this particular problem: I loosened the SIM cover screws a few turns, but the cover remains firmly in place.
Are the SIM cover screws captured or loose? That is, after removing the cover, can the screws fall out or they stay in place? As I loosened the screws they did not rise up, then stayed flush with the case. This suggests that they are captured, that the cover is stuck in place (with that often mentioned sealant?), and that by loosening the screws I may have stripped the case threads.
If the screws are not captured, then why didn't they rise up, even if the cover was stuck? How many screw turns does it take before the SIM cover can be removed?
BTW, after "loosening" the screws I did try prying the cover up with a knife blade. No luck.
That is a new one.
The sim screws only have maybe 4 threads in to hold them in the watch body. I think there are little tiny washers on the inside that holds them more or less onto the sim slot cover plate (which is a symmetric, though that is not blindingly obvious). They can fall out anyway, because any washers that might have been installed tend to break and tear and self destruct, which is convenient for Omate because then they can void any water-resistance warranty you might have felt you deserved (this is a big priority for Omate, apparently, damage control...)
Under the plate is a flimsy black plastic gasket (usually, depending on assembly issues), and you should just pry the plate out. It will eventually give up. Or, you could open the back cover and remove parts cleaning the crap out from where the drunken underpaid Umeox assembler got especially sloppy. Then you could push your sim slot cover plate out from the inside, probably.
Sent from my Nexus 7 using Tapatalk
Armed with your info, I had another go at it under an illuminated magnifier. Once again the screws loosened, but the cover was firmly stuck. Since there's no real gap between cover and case (nor should there be), I wedged the point of an xacto blade into one of the microscopic screw slots and gave a little sideways prying action -- the cover popped off.
Next up, a second trip to ATT to enable service.
Related
the lens on my back cover cracked when dropped a while back, and to get a good photo i now have to remove the back cover to get the obstruction off... is there anything i can buy short of a whole new back cover? all i need is a sticky piece of glass like the one that comes on the original cover...
thanks!
Why don't you just take a piece of plastic and work on it with sandpaper? You could even use some cd jewel case. The material is usually fragile but if you make a cut on its surface with a sharp knife it will tend to brake along this line. So it's fairly easy to break it down to a rectangular shape roughly the size of the camera cover and work with sandpaper or a file until you have a proper shape. Putting some sticky paper cut to shape of the cover on the plastic (preferably on both sides) will help in achieving the proper shape and will protect the surface from scratching.
Just look around the hose and be creative - i'm sure you'll be able to find a piece of clear, non-scratched plastic somewhere If you feel that the cd-case plastic will be too soft and will scratch too easily you could apply a piece of screen protector to it. It sure isn't worth buying a new screen protector just for that but if you already have one on your phone you could use a piece of it to protect camera cover and get a new one for the screen
As for attaching the cover to g1 back cover, there are many ways ranging from glues to double-sided sticky tapes. Use whatever you have at your disposal (just stay away from cyanoacrylate adhesive aka super glue - its vapor will ruin the transparent plastic).
a new back cover is cheap, like $6.
Camera Lens
jnagar said:
the lens on my back cover cracked when dropped a while back, and to get a good photo i now have to remove the back cover to get the obstruction off... is there anything i can buy short of a whole new back cover? all i need is a sticky piece of glass like the one that comes on the original cover...
thanks!
Click to expand...
Click to collapse
what is your phone model? Different phones have different camera lens with varied shape. A camera lens can not be just replaced by a plastic stuff as the guy said above and it is a prttey tough thing to shape the plastic. an original camera lens does not much. It may be no more than $1。
Refer to the following thread where a person used a spray on material to create a soft touch battery door for a Nexus S. I wonder if this could be used on the rear cover for protection?
http://forum.xda-developers.com/showthread.php?t=881062
Cool idea. Most hardware stores I've been to have it, but its not always in spray form. I wouldn't mess with the dip stuff (often used for keys, tools, etc.) I might have to pick some up myself. Comes in some different colors as well sometimes.
I've had a key on my keychain that has been dipped and after 3yrs its almost ready to come off completely. Of course, I only used it to tell them apart.
I did it. Edit: Finally got the photos up.
I took the four screws off and removed the back panel. Used four small pieces of painters tape to cover up the screw holes, but actually let the rubber go underneath so the sides of the corners were covered and continuous as much as possible.
I put about five or six coatings on. Only bad part is that you need to wait 30+ minutes between coatings. I let it off gas a little before putting it all back together. It does stink a little, not headache inducing though, at first. After about 12hrs it just smells like rubber and isn't noticeable.
$7.50 or so at Lowe's for a can. I did this and a phone and there is still some left in it I believe.
Like the Nexus post says, it works best if there are few noncontinuous parts of the rubber to get snagged on things. This was part of the reason I removed the case.
No responsibility for messing yours up, etc. etc.
vsc said:
Refer to the following thread where a person used a spray on material to create a soft touch battery door for a Nexus S. I wonder if this could be used on the rear cover for protection?
http://forum.xda-developers.com/showthread.php?t=881062
Click to expand...
Click to collapse
This looks sweet vsc. I like my carbon fiber rear cover, but a soft rubberized grip would definitely be better.
Just added some photos up above. I forgot to add that the back case goes on just as easy as it came off. Buttons still work, and the little door still opens correctly. It *almost* looks like it could have come this way. Its actually thin enough you can still see a slight bump from where the sticker for the serial number is (not in the pictures though, sorry). I think it looks a bit better now than having all those extra words on the back of the case. My case had already started to get rather scratched up even when I was careful.
I'll try to update on durability if it starts to look bad.
One other thing. My corners don't look the greatest because the first time I did it I let it dry with the corner tape on and then had to exacto knife the plastic and tape off once it had dried. I think it would do better if you made nice rounded tape areas, or just bought some rounded stickers or something. But definitely put them on lightly and take them off between each coat so the corners dry without the tape/stickers.
Just wondering if it would be possible to remove the bottom section of the 'aluminium' frame the the ZU. The specific part of the frame is apparently made of a softer plastic which means it gets dented easily such as in my case. I've already purchased replacement materials but have no clue how to remove the originals. Any ideas?
Yeah, it's possible but I have no idea how. My guess is to remove the back panel, and then loosen the lower part. You can get the back panel off by heating it so the glue that holds the glass gets warm, and making the glass removable by using a small suction cup. I believe there are a few videos on YouTube, so I recommend you checking them out. Also, search for how to remove that bottom part on YouTube too if you haven't already.
My display was broken so I had to buy a new display and bought it along with the side frame. It's perfect but there's one problem-- the screw holes are kinda not in perfect size so none of the 16 screws fit in tightly. They are just somehow screwed in, holding the inner back cover with the sideframe. I'm afraid that if the phone falls, the inner back cover might rip off the sideframe and display assembly and totally rip apart damaging the motherboard, etc.
Since the screws aren't holding the phone tightly in place, I wanna take some measures so as to prevent it from ripping off incase of a fall. I applied very little amount of super glue (fewikwik, popular in India) at two places. But I DO NOT want to use super glue further around the frame because it'll become impossible to remove the inner back cover in future.
My question is, is there any sort of "super glue" available that stick things (plastic here) very firmly but can be removed as well when needed? You can say I am looking for something stronger that typical fevicol but less stronger (and not permanent) than super glue (fewikwik).
you're looking for glue on XDA.
-z3r0- said:
you're looking for glue on XDA.
Click to expand...
Click to collapse
It's related to phone repair and I didn't wanna sign up at a new place for asking this.
I've had my new S21 for a few hours now, and I keep finding more and more strips of the protective plastic that needs to be peeled off . Does anyone make a special light which make this plastic fluoresce? Could be a great new product!
LOL, I agree.
If I recall correctly, think I found the two big obvious sheets covering the back plastic and the screen glass. Another smaller sheet covering the camera bump and lenses. Then two (three?) very skinny separate strips wrap the circumference of the phone (the metal frame). One starts just to the right of the bottom speaker grill and runs up to the power/volume buttons. Another strip from but button around the top of the phone. And a third strip from the left of the SIM card and up the left-hand side frame. The strips along the circumference are hard to see or feel, and you need to find the start/end of the strip in order to begin peeling it off. I used my fingernail to find each end-point, then picked at the end until it came free enough so I could grab and pull up the entire strip.
I hope I found them all as I've put the phone into a Samsung leather case, which fits so snugly I can barely get it back out.
Leave it be and case it.
Without a case it only a matter of time until it self destructs.
As the protective film works its way loose remove so grit that gets trap under it doesn't mar the phone's finish. Otherwise it helps to protect from case marring.
Leave the display factory protector on as long as possible until it degrades.