Just wondering if it would be possible to remove the bottom section of the 'aluminium' frame the the ZU. The specific part of the frame is apparently made of a softer plastic which means it gets dented easily such as in my case. I've already purchased replacement materials but have no clue how to remove the originals. Any ideas?
Yeah, it's possible but I have no idea how. My guess is to remove the back panel, and then loosen the lower part. You can get the back panel off by heating it so the glue that holds the glass gets warm, and making the glass removable by using a small suction cup. I believe there are a few videos on YouTube, so I recommend you checking them out. Also, search for how to remove that bottom part on YouTube too if you haven't already.
Related
Refer to the following thread where a person used a spray on material to create a soft touch battery door for a Nexus S. I wonder if this could be used on the rear cover for protection?
http://forum.xda-developers.com/showthread.php?t=881062
Cool idea. Most hardware stores I've been to have it, but its not always in spray form. I wouldn't mess with the dip stuff (often used for keys, tools, etc.) I might have to pick some up myself. Comes in some different colors as well sometimes.
I've had a key on my keychain that has been dipped and after 3yrs its almost ready to come off completely. Of course, I only used it to tell them apart.
I did it. Edit: Finally got the photos up.
I took the four screws off and removed the back panel. Used four small pieces of painters tape to cover up the screw holes, but actually let the rubber go underneath so the sides of the corners were covered and continuous as much as possible.
I put about five or six coatings on. Only bad part is that you need to wait 30+ minutes between coatings. I let it off gas a little before putting it all back together. It does stink a little, not headache inducing though, at first. After about 12hrs it just smells like rubber and isn't noticeable.
$7.50 or so at Lowe's for a can. I did this and a phone and there is still some left in it I believe.
Like the Nexus post says, it works best if there are few noncontinuous parts of the rubber to get snagged on things. This was part of the reason I removed the case.
No responsibility for messing yours up, etc. etc.
vsc said:
Refer to the following thread where a person used a spray on material to create a soft touch battery door for a Nexus S. I wonder if this could be used on the rear cover for protection?
http://forum.xda-developers.com/showthread.php?t=881062
Click to expand...
Click to collapse
This looks sweet vsc. I like my carbon fiber rear cover, but a soft rubberized grip would definitely be better.
Just added some photos up above. I forgot to add that the back case goes on just as easy as it came off. Buttons still work, and the little door still opens correctly. It *almost* looks like it could have come this way. Its actually thin enough you can still see a slight bump from where the sticker for the serial number is (not in the pictures though, sorry). I think it looks a bit better now than having all those extra words on the back of the case. My case had already started to get rather scratched up even when I was careful.
I'll try to update on durability if it starts to look bad.
One other thing. My corners don't look the greatest because the first time I did it I let it dry with the corner tape on and then had to exacto knife the plastic and tape off once it had dried. I think it would do better if you made nice rounded tape areas, or just bought some rounded stickers or something. But definitely put them on lightly and take them off between each coat so the corners dry without the tape/stickers.
Hi all, so I'm in the middle of replacing the digitizer for my TB. Got the new digitizer hooked in - there is supposed to be adhesive included, but I'm not sure what form it has taken. I have a clear piece of plaster with 2 printed tabs that say "Please peel off this mask before application" and "Please peel off this mark after application". I also have a white sticker looking thing, when I peel the paper back a see a clear piece of plastic inside. The only adhesive I've seen before goes around the sides - is the thunderbolt a clear platic adhesive that covers the whole surface? I'm assuming maybe one of these is a free screen protector they might have included? Pic of both attached
Edit: white sticker-looking one is a bit thinner than the width of the screen, am I supposed to cut this into strips to go around the outside?
Now that I go back and look - the listing I bought from didn't actually mention any adhesive, so I'm not 100% either of these necessarily are the adhesive.
rledge21 said:
Hi all, so I'm in the middle of replacing the digitizer for my TB. Got the new digitizer hooked in - there is supposed to be adhesive included, but I'm not sure what form it has taken. I have a clear piece of plaster with 2 printed tabs that say "Please peel off this mask before application" and "Please peel off this mark after application". I also have a white sticker looking thing, when I peel the paper back a see a clear piece of plastic inside. The only adhesive I've seen before goes around the sides - is the thunderbolt a clear platic adhesive that covers the whole surface? I'm assuming maybe one of these is a free screen protector they might have included? Pic of both attached
Edit: white sticker-looking one is a bit thinner than the width of the screen, am I supposed to cut this into strips to go around the outside?
Now that I go back and look - the listing I bought from didn't actually mention any adhesive, so I'm not 100% either of these necessarily are the adhesive.
Click to expand...
Click to collapse
It looks identical to the screen protectors from verizon, peel #1 off, apply to screen, peel #2 off, squeeze air bubbles out
Sent from my DROID BIONIC using XDA App
rledge21 said:
Hi all, so I'm in the middle of replacing the digitizer for my TB. Got the new digitizer hooked in - there is supposed to be adhesive included, but I'm not sure what form it has taken. I have a clear piece of plaster with 2 printed tabs that say "Please peel off this mask before application" and "Please peel off this mark after application". I also have a white sticker looking thing, when I peel the paper back a see a clear piece of plastic inside. The only adhesive I've seen before goes around the sides - is the thunderbolt a clear platic adhesive that covers the whole surface? I'm assuming maybe one of these is a free screen protector they might have included? Pic of both attached
Edit: white sticker-looking one is a bit thinner than the width of the screen, am I supposed to cut this into strips to go around the outside?
Now that I go back and look - the listing I bought from didn't actually mention any adhesive, so I'm not 100% either of these necessarily are the adhesive.
Click to expand...
Click to collapse
use an exacto knife and cut thin strips odd the white adhesive. Be careful not to cover sensors or have it too wife so that you can see it on the screen. Make sure you put enough along the bottom or you'll have the soft key lights bleed on the screen something fierce. Good luck!
Swyped Thunder coming at you
um.... Not sure what these other guys are talking about, but the guy I know that does these uses a 2mm tape made specifically for this task produced by 3M. If someone sent you a sheet of crap you gotta cut up to make work, you got hosed in my opinion. I believe in doing a job right, and THAT doesn't strike me as how they do it at HTC. I believe Amazon has the correct 3M tape for this job.
loonatik78 said:
um.... Not sure what these other guys are talking about, but the guy I know that does these uses a 2mm tape made specifically for this task produced by 3M. If someone sent you a sheet of crap you gotta cut up to make work, you got hosed in my opinion. I believe in doing a job right, and THAT doesn't strike me as how they do it at HTC. I believe Amazon has the correct 3M tape for this job.
Click to expand...
Click to collapse
Can you give me a link. It is greatly appreciated.
Here ya go.
They also have 3mm and 1mm, but 2mm is recommended. Just put it on the outer edge of the digitizer, don't let it overlap the black bezel. I highly recommend layering 2 strips on each side or you will not have enough space between the glass and LCD and eventually they will touch which will make it look like there is water inside it.
I haven't seen this posted already so I figured I would share. Anyways my brother just got a S4 for $120 but it came with cracked front glass. I told him I would fix the glass for him (my first time touching a S4 let alone replacing the front glass). Well I meant to take more pictures, but in the moment I just wanted to get the phone done. I followed a guide on iFixit and watched a couple videos on Youtube, alot of people are right when they say that the Youtube videos make it look simple. Anyways this was my first time working with LOCA glue (removing and replacing).
Here are some helpful tips:
#1 Make a jig that will hold your heat gun above your workspace, you will need to adjust the height depending on how well your heat gun works.
#2 Put some clear packaging tape on the front of the glass to avoid glass chipping and flying, also to keep glass from entering under the glass and scratching the digitizer..
#3 The glass is easiest removed with a temperature between 155f and 165f.
#4 Work top to bottom. Ear piece to button.
#5 When prying the glass off MAKE SURE you are between the glass and the digitizer, it is easy to lift the whole LCD assembly.
#6 Work slowly, if the glass if badly broken it will not pull up as easily as a less shattered glass. I found that the digitizer was not as fragile as I was made to believe.
#7 Have plastic razor blades or a plastic putty knife/scraper handy for the removal and cleanup of the LOCA glue.
#8 Have 2 lint free cloths handy for the cleanup and removal of the LOCA glue.
#9 When the glass is almost off remember to pry off the back and home button sensors from the bottom of the glass.
#10 When it is time to clean up the digitizer use your putty knife/scraper to get most of it up.
#11 I found that Eucalyptus oil works well at removing the rest of the LOCA glue. Just put some on a Q-tip and swab the area you want to clean.
Here is a pic of what the digitizer looked like after cleaning with Eucalyptus oil.
EDIT: Sorry pic wouldn't link, had to make it an attachment.
I'm not gonna lie, while putting the new glass on I could not get all the air out, I did not get pics of the finished screen, but it only has a couple small bubbles. Well worth the $10 for the new glass.
fyca said:
I haven't seen this posted already so I figured I would share.....
....I'm not gonna lie, while putting the new glass on I could not get all the air out, I did not get pics of the finished screen, but it only has a couple small bubbles. Well worth the $10 for the new glass.
Click to expand...
Click to collapse
nice write-up. shame that the image alone has over 500 views and nobody else has hit the "thank" button
well i thank you @fyca for the info and your time! :good:
Hey guys,
My first digitizer replacement ended up in a few big flower shaped flecks on the screen. That is not what I expected. I am very curious to know how these flecks appeared, or how I could avoid this will happen again. Also it looked to me like the original brightness could not be achieved.
This is the phone (Jiayu G2s) with the Calendar active which is almost an entire white display.
anybody who recognizes this?
oh, and by the way everything functions normal.
1_Petje
Looks like you overheated the actual screen. If you apply too much heat you will lose colors/brightness in those areas.
Heat not the only cause......
1_Petje said:
Hey guys,
My first digitizer replacement ended up in a few big flower shaped flecks on the screen. That is not what I expected. I am very curious to know how these flecks appeared, or how I could avoid this will happen again. Also it looked to me like the original brightness could not be achieved.
Link removed because someone failed to think;New posters have to quote the question in their posts, and may quote a link...Sheesh! //i58.tinypic.com/2duawkm.jpg
This is the phone (Jiayu G2s) with the Calendar active which is almost an entire white display.
anybody who recognizes this?
oh, and by the way everything functions normal.
Click to expand...
Click to collapse
The "flowers" that you see can be caused by too much heat. BUT, these appear to be the result of excessive pressure placed on the display. If you press hard enough on almost any lcd or led display you'll see these kinds of patterns. If you let off they go away, unless you've pressed to hard or too long. AMOLED are particularly sensitive when heated. Long and short, be careful how much pressure you use when removing the glass etc....
I replaced an s3 screen twice. It was obviously easier the second time, as there was no LOCA to fight with. The main reason for diminished clarity and sharpness after replacement is the absence of the LOCA. Once u manage to get the glass off and do the necessary cleaning/preparation for reassembly, applying 3-4cc's of LOCA onto the digitizer in a vertically stretched "X" pattern will give u that genuine factory screen appearance. Well...After u cure it under UV light. But...for a novice, applying the LOCA and making it look good without permanently damaging the device is extremely tricky. And shouldn't b attempted if you're not somewhat of a professional, as the glue can seep down into your phone's internal hardware.
fyca said:
I haven't seen this posted already so I figured I would share. Anyways my brother just got a S4 for $120 but it came with cracked front glass. I told him I would fix the glass for him (my first time touching a S4 let alone replacing the front glass). Well I meant to take more pictures, but in the moment I just wanted to get the phone done. I followed a guide on iFixit and watched a couple videos on Youtube, alot of people are right when they say that the Youtube videos make it look simple. Anyways this was my first time working with LOCA glue (removing and replacing).
Here are some helpful tips:
#1 Make a jig that will hold your heat gun above your workspace, you will need to adjust the height depending on how well your heat gun works.
#2 Put some clear packaging tape on the front of the glass to avoid glass chipping and flying, also to keep glass from entering under the glass and scratching the digitizer..
#3 The glass is easiest removed with a temperature between 155f and 165f.
#4 Work top to bottom. Ear piece to button.
#5 When prying the glass off MAKE SURE you are between the glass and the digitizer, it is easy to lift the whole LCD assembly.
#6 Work slowly, if the glass if badly broken it will not pull up as easily as a less shattered glass. I found that the digitizer was not as fragile as I was made to believe.
#7 Have plastic razor blades or a plastic putty knife/scraper handy for the removal and cleanup of the LOCA glue.
#8 Have 2 lint free cloths handy for the cleanup and removal of the LOCA glue.
#9 When the glass is almost off remember to pry off the back and home button sensors from the bottom of the glass.
#10 When it is time to clean up the digitizer use your putty knife/scraper to get most of it up.
#11 I found that Eucalyptus oil works well at removing the rest of the LOCA glue. Just put some on a Q-tip and swab the area you want to clean.
Here is a pic of what the digitizer looked like after cleaning with Eucalyptus oil.
EDIT: Sorry pic wouldn't link, had to make it an attachment.
I'm not gonna lie, while putting the new glass on I could not get all the air out, I did not get pics of the finished screen, but it only has a couple small bubbles. Well worth the $10 for the new glass.
Click to expand...
Click to collapse
hi. thanks for the tip... i have 1 question at the moment, and it might sound silly... but what kind of eucalyptus oil did you use and where from? i did a search on it and there were all sorts of brands and use, and seems forms of it...
i like lighter fluid personally but its to runny but is perfect it you can keep it from behind the lcd and messing up the sheets on the likes of a LG G3.
The eucalyptus oil I used was an essential oil from my local co-op/natural foods store.
Go to lcdbondingusa dot com. They have this cleaner for cleaning LOCA. Man let me tell you, it's well worth the cost. I use a diabetic syringe to get it between the LCD and Digi. Sure does make easy work of it. It's great for other stuff, too.
" Lcd Adhesive Remover Cleaner For UV Glue OCA Glue iPhone & samsung Safe To Use" is the way it was layed out on the eBay page
My display was broken so I had to buy a new display and bought it along with the side frame. It's perfect but there's one problem-- the screw holes are kinda not in perfect size so none of the 16 screws fit in tightly. They are just somehow screwed in, holding the inner back cover with the sideframe. I'm afraid that if the phone falls, the inner back cover might rip off the sideframe and display assembly and totally rip apart damaging the motherboard, etc.
Since the screws aren't holding the phone tightly in place, I wanna take some measures so as to prevent it from ripping off incase of a fall. I applied very little amount of super glue (fewikwik, popular in India) at two places. But I DO NOT want to use super glue further around the frame because it'll become impossible to remove the inner back cover in future.
My question is, is there any sort of "super glue" available that stick things (plastic here) very firmly but can be removed as well when needed? You can say I am looking for something stronger that typical fevicol but less stronger (and not permanent) than super glue (fewikwik).
you're looking for glue on XDA.
-z3r0- said:
you're looking for glue on XDA.
Click to expand...
Click to collapse
It's related to phone repair and I didn't wanna sign up at a new place for asking this.
I've had my new S21 for a few hours now, and I keep finding more and more strips of the protective plastic that needs to be peeled off . Does anyone make a special light which make this plastic fluoresce? Could be a great new product!
LOL, I agree.
If I recall correctly, think I found the two big obvious sheets covering the back plastic and the screen glass. Another smaller sheet covering the camera bump and lenses. Then two (three?) very skinny separate strips wrap the circumference of the phone (the metal frame). One starts just to the right of the bottom speaker grill and runs up to the power/volume buttons. Another strip from but button around the top of the phone. And a third strip from the left of the SIM card and up the left-hand side frame. The strips along the circumference are hard to see or feel, and you need to find the start/end of the strip in order to begin peeling it off. I used my fingernail to find each end-point, then picked at the end until it came free enough so I could grab and pull up the entire strip.
I hope I found them all as I've put the phone into a Samsung leather case, which fits so snugly I can barely get it back out.
Leave it be and case it.
Without a case it only a matter of time until it self destructs.
As the protective film works its way loose remove so grit that gets trap under it doesn't mar the phone's finish. Otherwise it helps to protect from case marring.
Leave the display factory protector on as long as possible until it degrades.