Related
hello...i hope that someone can help me....when i try to turn off the device,it shut down and after few seconds reboot?why?
also simetime the phone don't turn on and on screen i see a green battery with a thermo....someon can help me?
Did you find the answer to this? i am sending my SGS2 back for replacement. i have the same errors plus the following.
Phone selects speaker rather than earpiece as default for incoming/outgoing calls
Phone on ocasions randomly starts Kies and Voice commands even if there is no physical contact with the phone
sometimes the phone defaults back to a launcher i have never seen before (it is not touchwiz) and i have no idea how to launch it without it doing it automatically.
The faults you mentioned can be bypassed with a battery pull but they are annoying, I didn't have these problems until i upgraded my firmware through Kies to KE7.
I have an O2 branded device.
woody_2k said:
Did you find the answer to this? i am sending my SGS2 back for replacement. i have the same errors plus the following.
Phone selects speaker rather than earpiece as default for incoming/outgoing calls
Phone on ocasions randomly starts Kies and Voice commands even if there is no physical contact with the phone
sometimes the phone defaults back to a launcher i have never seen before (it is not touchwiz) and i have no idea how to launch it without it doing it automatically.
The faults you mentioned can be bypassed with a battery pull but they are annoying, I didn't have these problems until i upgraded my firmware through Kies to KE7.
I have an O2 branded device.
Click to expand...
Click to collapse
same issues to me... I'm trying to fix it flashing a stock rom without good results yet In the meantime I'm waiting for a USB jig from ebay before to send it to technical service
I have a I9100M(BELL) flashed with cognition 1.32 with same problem.
Randomly my phone will:
-go into driving mode
-answer calls in speaker phone mode
-start alarm clock
-think its charging when the cable is not plugged in
-Reboot it self/turn it self on when its off
-wont connect to computer or charge even when cable is plugged in.
I need to send it in for repairs what should i flash? there is no bell branded firmwares or roms.
jinxedsoul said:
I have a I9100M(BELL) flashed with cognition 1.32 with same problem.
Randomly my phone will:
-go into driving mode
-answer calls in speaker phone mode
-start alarm clock
-think its charging when the cable is not plugged in
-Reboot it self/turn it self on when its off
-wont connect to computer or charge even when cable is plugged in.
I need to send it in for repairs what should i flash? there is no bell branded firmwares or roms.
Click to expand...
Click to collapse
Exactly the same to me
How do you flash congnition? just over the stock rom with odin?
did you flash modem?
Absolutely same here, since coming from CM7 to VillainRom.
Never had that before.
I´m waiting and watching it and your results!
Thanks for this thread.
That's why I don't root the phone..it works fine.
---
- Sent from my iPad using Tapatalk
pachi72 said:
That's why I don't root the phone..it works fine.
---
- Sent from my iPad using Tapatalk
Click to expand...
Click to collapse
This has nothing to do with root access.
I cannot believe that any problem related just because you have access to your system.
Back to topic, flashed back to cm but problem persists.
It's getting really bad near to flashing stock and bring it back to change device if someone knows what it is could be helpful.
I also have this problem. I think it has something to do with the usb port.
Because sometimes it just scans for media, or it thinks it is charging. Really weird! Then i just put in the charger and it stops for a while. Turning off will just reboot the device. And removing battery and plugging it back it also just reboots the phone.
I hope it is not hardware related...
I was looking for help for a problem I have but this seems to cover most of the problems I'm having.
Mine has recently started going into a strange mode after shutting it down. I get the battery charging symbol alternating with the "battery overheating" symbol.
The only way to stop it is to remove the battery for at least a couple of hours (if you put it straight back in it automaticly starts up and goes back to flashing the battery warnings) or pressing Power, Vol+ and Home and choosing Reboot.
I have also noticed its very slow to respond to plugging the charger in or out. It doesn't always wake-up and bleep when the charger is put in and it stays showing its charging for some time after the charger has been removed.
I was told that the charger should be removed as soon as charging is compleated but surely overnight is the only time we have available to charge these phones!
Depending on the custom rom or kernel you are using, it might not support off mode charging.
To avoid having a "problem" with charging the phone in off mode, some developers decided to make the phone boot up when the phone is been charged when the phone is off.
Going back to an official stock ROM fixes this problem.
cyanogen mod 7 said:
cm_galaxys2_full-23.zip (2011-08-15 08:48:18)
Enable power off charging (LPM) (android_device_samsung_galaxys2)
Click to expand...
Click to collapse
As for Cyanogen, since built 23, you can charge the phone when it is in the "off" state. Please wipe out your userdata partition before flashing. Do not restore from a previous backup.
I fixed my reboot problem (rebooting instead of turning off) by letting the battery drain all the way so it couldn't boot anymore. Tried turning it on to see if it really doesn't go on anymore. After that I plugged in the charger and I got the charging-symbol and it did not turn on so I kept it charging overnight while turned off and in the morning it was finished and turned it on.
I also cleaned the usb-port on the phone with a toothpick. It had alot of dust stuck in it which I couldn't see. After that no more problems...for now. They haven't returned for 2 days now.
WoollyBully said:
I was looking for help for a problem I have but this seems to cover most of the problems I'm having.
Mine has recently started going into a strange mode after shutting it down. I get the battery charging symbol alternating with the "battery overheating" symbol.
The only way to stop it is to remove the battery for at least a couple of hours (if you put it straight back in it automaticly starts up and goes back to flashing the battery warnings) or pressing Power, Vol+ and Home and choosing Reboot.
I have also noticed its very slow to respond to plugging the charger in or out. It doesn't always wake-up and bleep when the charger is put in and it stays showing its charging for some time after the charger has been removed.
I was told that the charger should be removed as soon as charging is compleated but surely overnight is the only time we have available to charge these phones!
Click to expand...
Click to collapse
What kernel and rom are you using? I have not seen the battery overheating symbol on the sgs2.
No, there is no need to remove the phone from charger, when the phone gets to what is considered full, the battery will stop charging by itself.
Are you using the original samsung charger that came with the phone, or are you using a after market charger? Most of these USB chargers do not send a signal on the data lines. When using these chargers, the phone becomes laggy and unresponsive, there is also a delay to register anything on the touch screen. Stay away from these chargers.
For lithium batteries just charge it whenever you feel like it. Lithium batteries have a few thousand deep charge cycles, meaning if you use up all the power, then charge it,you use 1 deep charge cycle. However, if you use the micro cycles for charging, you can charge the batteries a few million times. Leaving the battery on empty for too long will damage the lithium battery.
Can any one confirm if this is a hardware or software issue as i now have the problem when i try and switch the phone off it will just reboot?
The Same issue occurs in my sgs2
hi everybody,
i just got my sgs2 ten days ago
everything seems good at first
then i realized screen standby lock lag problem, there exist a lag between 1 second to 2.5 seconds.
i ignore that due to it cannot be named as a problem, it seems like a bad characteristic
then yesterday , i have faced with another problem
after i have docked the phone to the original vehicle dock kit,
phone cannot be closed via power button , i hold it 1.5 seconds then chose turn off among list, phone looks like to be turned off then after a little while it just vibrates and reboots. That is phone cannot be turned off, it s somehow turn itself on again.
Whats the reason of this problem ?
In another forum one faced with the same problem said that it turned out to be normal when the battery is erased but the problem is occured again after docking.
micro usb connector
I droped my phone in the water, got it alive again, but with all the error(overheat battery symbol, no stable usb connection, reboot when i power off, 100% charged not going away) replaced the micro usb connector with a new one.
Some problems are gone but i still can't connect to pc (kies, debug etc), poweroff problem still happen sometime.
Conclusion: It is not only the usb part of the phone that are causing this problem.
But I do belive its a hardware problem.
Have you phone maybe got to much to drink too..
usb port???
I've recently been experiencing the same problem
When I turned off my phone it switched on again!
And removing battery and plugging it back it also just reboots the phone.
Sometimes the USB connector and charger are confused
Do solved the problem by changing the USB port?
plz help me
Thank you in advance for helping me
This is definately a hardware issue. Clean the usb connector, failing that it will need replacing
On Behalf of SamsungCarla:
"Hello,
Samsung takes all product related issues seriously. We invite the customer to contact us so that they can examine the phone to determine the cause of this incident. If you send us your name, phone number, phone IMEI, where the product was purchased, and email address to [email protected], we will contact you to see how we can help.
Sincerely,
SamsungCarla
Samsung Support"
Hi all,
I have an AT&T Samsung Galaxy S 2 (i777). It was rooted and running CM 10.1. A few months ago it started to have charging/USB port issues. Some of the symptoms:
-Sporadic charging (starting and stopping)
-Required USB jiggling to get it to start charging
-Sometimes wouldn't charge at all until it died, then would eventually charge while powered off
-Would not shutdown (only reboot, even if the battery was removed)
-Randomly started "car mode"
My initial thoughts on this were USB port issues. After doing some research on people with similar problems, I tried cleaning the port with alcohol, toothbrush, compressed air, etc. No avail.
Eventually the phone just stopped charging altogether. At this point, if I left it plugged in, it would sit in a continuous boot loop (boot, get to lock screen, realize it has no juice, shutdown, rinse, repeat). After a few days of attempting to charge and just having that happen, it went black and has never turned on since.
To try to solve that, I bought a new USB port flex cable on eBay and replaced it, assuming this would solve all my USB port issues. I tried to be as ESD safe as possible and also not break anything in the phone, but after replacing the board, it still wouldn't boot.
Next step- bought a new battery with an external charger to skip the USB port altogether and see if the battery was shot. Charged up the new battery, popped it in, nothing.
I'm at a total loss. If it started as a charging problem, I don't see how the problem could have been anywhere but the flex cable board or the battery. Does anyone have any ideas about what might be going wrong? I would REALLY appreciate some insight.
Thanks!
Maybe the repeated loops damage it
Sent from my GS4 running CM11 Kandy Kane
aptbosox said:
Hi all,
I have an AT&T Samsung Galaxy S 2 (i777). I
Eventually the phone just stopped charging altogether. At this point, if I left it plugged in, it would sit in a continuous boot loop (boot, get to lock screen, realize it has no juice, shutdown, rinse, repeat). After a few days of attempting to charge and just having that happen, it went black and has never turned on since.
To try to solve that, I bought a new USB port flex cable on eBay and replaced it, assuming this would solve all my USB port issues. I tried to be as ESD safe as possible and also not break anything in the phone, but after replacing the board, it still wouldn't boot.
Next step- bought a new battery with an external charger to skip the USB port altogether and see if the battery was shot. Charged up the new battery, popped it in, nothing.
I'm at a total loss. If it started as a charging problem, I don't see how the problem could have been anywhere but the flex cable board or the battery. Does anyone have any ideas about what might be going wrong? I would REALLY appreciate some insight.
Thanks!
Click to expand...
Click to collapse
Did you ever find a solution? I'm in the no charge boot loop after letting it die last night.
I have not seen previous usb problems at all. I suspect that my battery got over-drained, but then I've got the same symptoms as you and you have a new battery. I can get it into recovery but t won't stay on in CWM for long enough to fix permissions, which is the only thing I've tried so far in CWM.
Thanks
If i was in your place i'd have taken it to the nearest Samsung Service center and let them fix it for me.
I think the fluctuation in power may have damaged your phone battery point from where it takes power from the battery and charge it.
Maybe it has damaged the motherboard.
We cannot say anything in this situation.
You should just take it to your nearest service center.
Best of Luck
OK, wiping Data fixed it.
Thanks for your reply. This problem just started this morning with no previous issues, doing the looping part of your problem that I quoted. so it's not a question of what I might have done.
But, for others encountering my part of it, here's what I've done and learned so far today.
As I looked into things elsewhere on the , it seemed to be a software problem. Luckily, I have another Galaxy (Exhibit) that's similar battery and I was able to put the charged battery from it into the SII. The SII booted and worked fine but did not charge. I put the SII battery into the Exhibit (sorta fits). It took a charge.
This confirmed to me that it's not the battery. It must be the phone perhaps USB port or more likely "firmware" since problem started abruptly after draining battery down.
I then wiped data on the SII from CWM/recovery and rebooted.
SII is now charging again. Stock battery is back in and working.
Time will tell if all is well, but here's what I think happened:
1) battery drained down to zero while unplugged
2) plugging in and starting up phone immediately threw something off in the battery stats at a low level...that kept it from charging even when turned off. Or rather threw it into a loop. Don't really understand this stuff, but may have to do with physical things that happen in a battery when the cells drop down way low and then the voltage feedback they give to charging circuit.
3) charging battery in another device (gingerbread, by the way) got the battery out of this, if battery had been a contributing factor,(or just a trigger) it was back over the hump.
4) wiping data fixed the charging, so I conclude it was a charging circuit data issue triggered by an ultra low battery.
Hope I'm over this problem and hope that it helps somebody else. If you run into this yourself with no previous USB or hardware issues, I'd suspect software before hardware. If I had only one battery and no way to charge it externally, I would suggest get one of those simple universal clip-on chargers to bring the battery back up and then go into CWM and wipe data.
UPDATE: It's stopped charging again. It's no longer looping since I got the battery charged up, but not right either. As soon as I plug it into a USB, it boots itself without powering on.
I guess that this is looking more like a physical USB issue now. Weird that there's been no previous sign of trouble before today.
UPDATE2: I cleaned USB port but no help. Then I bent the USB contacts towards the screen and it is charging now again. I'm ordering a replacement USB.
I should add that I'm running Shostock Jellybean, older (not current) version with it's associated Jeboo kernel. Don't know if it matters.
I wish I'd seen your post sooner.. I had exactly the same problems back in January. Took all the same steps you did. In the end, an 8$ USB flex cable from EBay solved the problem. I think you'll have luck with that:thumbup:
Sent from my Slimbeaned Sgh-I777 (unbricked x4 )
hey, I'm experiencing the same issue slightly different.
-Sporadic charging (starting and stopping)
-Randomly started "car mode"
-plugged in the charger while the device is switched off, it automatically turns the device on.
-If the cable still plugged in while the charger removed from the main current, it shows "Charging stopped. High voltage"
-From yesterday, it doesn't charge even. Only way to charge is, connect the charger first and then Restart the device.
Then only charging continuous.
Can anyone help to solve this? Is this a software issue?
Thanks!
---------- Post added at 04:50 AM ---------- Previous post was at 04:46 AM ----------
Also, there was this issue early --> when I charge it from the laptop, the USB mode doesn't switch on. It just charge the phone only.
But now it's not even working like that.
Tweaker7376 said:
I wish I'd seen your post sooner.. I had exactly the same problems back in January. Took all the same steps you did. In the end, an 8$ USB flex cable from EBay solved the problem. I think you'll have luck with that:thumbup:
Sent from my Slimbeaned Sgh-I777 (unbricked x4 )
Click to expand...
Click to collapse
Which flex cable you bought exactly...plz give me the link...i badly need one...thx
mmystere68 said:
Which flex cable you bought exactly...plz give me the link...i badly need one...thx
Click to expand...
Click to collapse
Hey bro.. I've been offline forever.. Did you ever get what you needed?? I can pm you some info:good:
Tweaker7376 said:
Hey bro.. I've been offline forever.. Did you ever get what you needed?? I can pm you some info:good:
Click to expand...
Click to collapse
Tweaker7376 said:
I wish I'd seen your post sooner.. I had exactly the same problems back in January. Took all the same steps you did. In the end, an 8$ USB flex cable from EBay solved the problem. I think you'll have luck with that:thumbup:
Sent from my Slimbeaned Sgh-I777 (unbricked x4 )
Click to expand...
Click to collapse
hi, my s2 wont charge. It just shows up charging when plugged in but it doesnt charge at all. and it overheats too much while plugged in. What is that flex cable you said, is it the one that connects the charging port to the motherboard? were you the one opened and replaced it? thanks
Hi there. I promised my girlfriend to make her Samsung Galaxy S2 work again. The thing is, suddenly it won't charge. After trying several different chargers did I bought a new battery. But it didn't work either. Then I bought a new USB charging port and replaced it yesterday. After I plugged in the Charger, the screen shows the charging batteri screen for a couple of seconds and the went black. Then there was no power at all. I tried the other battery, I tried to make sure everything was as it should be inside on the motherboard.
Please help me..
I tried to make a hard reset but it didn't start op of course because the battery has no juice. I tried to unplug the battery for 10 seconds, then I plugged the charger in and afterwards the battery, but still no sign of power.
matthieusimon said:
Hi there. I promised my girlfriend to make her Samsung Galaxy S2 work again. The thing is, suddenly it won't charge. After trying several different chargers did I bought a new battery. But it didn't work either. Then I bought a new USB charging port and replaced it yesterday. After I plugged in the Charger, the screen shows the charging batteri screen for a couple of seconds and the went black. Then there was no power at all. I tried the other battery, I tried to make sure everything was as it should be inside on the motherboard.
Please help me..
I tried to make a hard reset but it didn't start op of course because the battery has no juice. I tried to unplug the battery for 10 seconds, then I plugged the charger in and afterwards the battery, but still no sign of power.
Click to expand...
Click to collapse
Hm... you should always be able to start the phone via charger, otherwise something is severly broken.
My advice: Get your girlfriend a new phone or rather take her out for a nice dinner!
It's cheaper and you'll have a great time, hopefully.
PS Get the money back for USB charging port and battery. Women are a really terrible influence on men.......
Conny84 said:
Hm... you should always be able to start the phone via charger, otherwise something is severly broken.
Click to expand...
Click to collapse
Hi, i am having similar situation, but i would like to be sure, its definitelly dead. What's different in my case, i was using CM 11 M8 and updated to M9 the day it was released, no problem with booting, just to the moment, when battery dropped to 0% and phone turned off. When i plugged it in, i was there - nothing, black screen, no access do download or CMW mode, tried other battery but no luck.
I just dont understand what has happened, that simple update can kill the phone or what?
Hello,
I have an unrooted Z2. With around 30% battery left, I put it in the charging dock on my desktop yesterday evening. After 1 or 2 hours, I noticed that the phone is completely dead - no LEDs are blinking, no vibration, nothing. I tried pressing the power button alone, in combination with VolumeDown, VolumeUp, CameraButton, for more than 30 seconds each. I tried pressing down the tiny red button next to the SIM slot for awhile. Nothing. Phone is dead like a brick.
The only result I'm getting is when I plug it into my computer (ubuntu 14.10) - the LED bar on top is showing a constant red color in this case. Doing the button presses outlined above in this situation is also pointless.
I'm installing flashtool for Linux right now, the connection is pretty slow and it will take awhile. I hope to find out more afterwards. I'm a newbie when it comes to flashing sony phones, only found out now about flashtool. Any advice/tip on how to proceed, or if it even makes sense to dig into this, is highly appreciated.
Thanks in advance!
Hello,
are you perfectly sure your dock was connected properly and it hasn't discharged your phone? Maybe there was something wrong with it.
I had similar situation while I was low on battery and I was creating backup in recovery. Then I fell asleep and I have found my phone completely 'dead'. I connected it to the wall charger and nothing. No led, no nothing. I have even connected it to my pc and also nothing happened. Then I connected my Z2 to the wall charger and I left it like that. And after few hours, out of the blue, just turned itself on, just like my old Nokia n95.
I'm sorry it's not quite solution you looked for, but give it a try. Essential is to charge it via wall charger.
Good luck!
Do what @amon87 says OP. Charge it on a wall charger for a minimum of 3-4 hours; If that doesn't work, can you specify whether you were using a legitimate Sony dock or a third party dock? If it was third party, it could possibly have caused a hardware problem with your device via the magnetic charge pins (not extremely likely but not unheard of). Worst case scenario, send it back to Sony in the next few days. The warranty will cover it if you haven't caused water damage or anything like that.
Thanks for your replies! I also hoped for a sudden discharge, so I removed the device from the dock, plugged the USB in directly, and left it overnight - still nothing. Also, I have the original Sony dock, and have never exposed the device to any water.
Found out the model number in the meantime, it's D5303, if it's of any help. Flashtool does not see the device, unfortunately. I just found out that Sony describes an option to restore your device through the official PC companion app - I'll give that a try when I'm home, and will report back tomorrow.
Otherwise I guess my only option is the warranty.
There's also an option to quickly plug in and out charging wire to kick-start the battery. Unfortunatelly i have no further ideas to help you out.
Don't give your hopes up, try again. There's been a thread of a guy whose Z2 turned itself off and it seemed dead, but after a day or two it just turned on.
So, of course it's also not detected by Sony's "Bridge for Mac" app. Plugging it in and out brought also no results.
As the device is still covered by warranty, and I have yet not tampered with it, I've sent it in for repair! My pocket feels so empty now, i wonder how life is going to be without a phone. Apparently they need 5 - 10 working days.
Thanks for your kind support, guys!
Sorry to hear that. Hope it will get fixed!
I have noticed that fast Charging does not always happen even with the stock charger. However, if I reboot then fast charging kicks in. Is this a known issue?
No, I always have fast charging. Maybe you need to return your tab for warranty.
Techvir said:
I have noticed that fast Charging does not always happen even with the stock charger. However, if I reboot then fast charging kicks in. Is this a known issue?
Click to expand...
Click to collapse
I have this problem as a result of getting something in the charging port, or inside the USBC cable itself. All resulting in a moisture detected error. Powering down the tablet, plugging it in and allowing the charge indicator to come on would resolve the issue, but every time I unplug the tablet I would get the error again. I followed instructions on XDA regarding USB C fast charging problems and it seemed to fix the error. I think there's still something in the cable itself because the whole problem has expressed twice now. But in the interim comma over a few days if I plug the charger in one way I would get a slow charge warning that I wasn't using the original charger. But it's the charger that came in the Box. If I unplugged it, turned the charger around and plugged it in the other way it would fast charge again. So I'm guessing there's some kind of material in the charger itself that I can't get to that's affecting how many contacts are being made. I'm still working to resolve the issue with the original charger, but I'm thinking about just getting another USB C cable. I need a longer one than ships with the tablet in the first place.
When I went to chat with customer service, they wanted me to send it in under warranty. But I really didn't want to do without the tablet for 2 weeks or more, so researching it online has solved the issue somewhat. I might take it in to a Samsung kiosk and just see if they'll try to fix it with air duster.