Hello, I'm having a few different issues when I go to install the latest 4.4.3 (or any for that matter) RUU. I've connected my phone to my laptop and downloaded HTC sync and have automatically updated the drivers. However when I go to actually install the ruu, the usb disconnects and I'm forced to hard reset the phone to get it unstuck. I've tried this with two different USB cords and two separate computers. Any advice? Stuck without service and I'd really like to see UPSM and boomsound improvements. This is completely stock. Thank you
What OS. USB 3.0 ports or 2.0…?
Win 8.1 with USB 3.0 ports can be finicky to get it to work just right.
- Sent from a payphone ...
tommy_riley said:
What OS. USB 3.0 ports or 2.0…?
Win 8.1 with USB 3.0 ports can be finicky to get it to work just right.
- Sent from a payphone ...
Click to expand...
Click to collapse
Both are running Windows 7. I'm not sure on the USB ports, I believe they're 2.0
What hboot numbers is the phone currently on?
It is the AT&T branded version M8, correct? I only ask, because folks sometimes come on here trying to flash an AT&T RUU on another version device.
Any error messages when the RUU fails?
redpoint73 said:
What hboot numbers is the phone currently on?
It is the AT&T branded version M8, correct? I only ask, because folks sometimes come on here trying to flash an AT&T RUU on another version device.
Any error messages when the RUU fails?
Click to expand...
Click to collapse
The # is 3.16.0.000. The errors I receive are 170 & 171, something about the usb disconnectingand to check it and try again.
Sounds like a driver issue. Uninstall HTC related drivers and install the drivers from adb or the google drivers.
- Sent from a payphone ...
tommy_riley said:
Sounds like a driver issue. Uninstall HTC related drivers and install the drivers from adb or the google drivers.
- Sent from a payphone ...
Click to expand...
Click to collapse
Just tried this as suggested abd still getting the same error. I get far enough that I can accept the version update on the ruu, the phone displays "HTC" against a black screen, and the usb disconnects. I uninstalled all the drivers and after I plugged in the cord, the sync manager said it was updating the drivers. Should o uninstall sync manager and try again?
Yeah get rid of sync manager. After its gone try the alternative drivers and make sure the phone comes up correctly in device manager then try RUU again. It might be a matter of trying a few different driver vs RUU combinations.
If the system only has USB 3.0 ports and its an Intel chip set then you might also try and go install the latest Intel USB port drivers directly from their website. If the USB port drivers are outdated or if Microsoft has their drivers in for USB instead of Intel's (on 3.0 ports only most of the time) what will happen is everything will look fine with connection to phone via USB from computer but once you are in recovery or fastboot mode the connection will be lost.
I can give more specifics if you want to go down this route much later in the evening with screen shots and driver locations if needed, I'm just on my phone ATM on my way to work. So it would be much later tonight. Let me know...
- Sent from a payphone ...
tommy_riley said:
Yeah get rid of sync manager. After its gone try the alternative drivers and make sure the phone comes up correctly in device manager then try RUU again. It might be a matter of trying a few different driver vs RUU combinations.
If the system only has USB 3.0 ports and its an Intel chip set then you might also try and go install the latest Intel USB port drivers directly from their website. If the USB port drivers are outdated or if Microsoft has their drivers in for USB instead of Intel's (on 3.0 ports only most of the time) what will happen is everything will look fine with connection to phone via USB from computer but once you are in recovery or fastboot mode the connection will be lost.
I can give more specifics if you want to go down this route much later in the evening with screen shots and driver locations if needed, I'm just on my phone ATM on my way to work. So it would be much later tonight. Let me know...
- Sent from a payphone ...
Click to expand...
Click to collapse
I uninstalled sync manager and the phone proceeded to Download the drivers again (in addition to an older sync manager driver for some reason) but still no avail. The laptop is definitely an Intel powered one, I'd greatly appreciate if you could post those screenshots when you get the chance
is fastboot enabled? If stock it is not enabled by default...enable it and try again. If you do not know how to enable it follow this:
Settings>About>Software information>More
Tap on build number 7 times repeatedly developer options will be enabled
Go back to settings open Developer options, make sure USB Debugging is enabled
WNC - Good point.
- Sent from a payphone ...
tommy_riley said:
WNC - Good point.
- Sent from a payphone ...
Click to expand...
Click to collapse
I tried installing it in fastboot usb but It didn't even detect the phone. Is there another type of fastboot or is that the only way?
Only one fastboot. Sounds more and more like a driver issue,be it a usb system driver update or htc driver update...something is amiss on that end.
Apologies for not getting back to this thread. Started a new work assignment this week causing my commute to significantly increase (along with a nasty storm yesterday resulting in power outage). I'll get back here this weekend when I have some time to login from home computer...
- Sent from a payphone ...
So, there are a few ways to check if you have USB3.0 drivers
One, is to look at the USB ports on your laptop/computer - unless it's a custom gaming rig, the USB2.0 ports plastic tabs will be black, while the USB3.0 ports will be blue - if all of your little plastic tabs inside the actual USB ports are blue, then sounds like you have USB3.0 ports only.
The other way is to go into your device manager and look at see what it lists under USB - refer to the below image. Should look like something similar to as follows:
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Now, provided that you have an INTEL chipset AND these 3.0 extensible drivers are currently using Microsoft drivers, then what you may want to do is replace the Microsoft Intel USB 3.0 drivers with the INTEL drivers themselves.
What you would look for is your chipset version of the intel chipset (e.g. C220, C217, C270 etc) you should see other areas in your device manager that will refer to your Intel chipset type) then do a search on Intel's website for "USB 3.0 driver C216" (or C220, C270 etc) and download the drivers for your version of Windows (Windows 7 64bit? probably)
The download center for Intel is here: https://downloadcenter.intel.com/
The original article where I ran into this same situation was located here - for some reason I still have it book marked. I was trying to update/root an HTC EVO LTE about two years ago and ran into this issue on Windows 8 - I imagine a similar issue exists on Windows 7 USB3.0 only systems. This allowed me to keep my connection to my EVO while in fastboot mode (no USB disconnected) on Windows 8 and do what I needed to do to root my phone. It was my first root and folks were saying it was impossible to use Win8 with USB3.0 only ports to accomplish this task, but using the method at the link I was able to : http://plugable.com/2012/12/01/windows-8-and-intel-usb-3-0-host-controllers
Here's to hoping you are running into something similar. If not, the next area I would try is just going to Intel's website and download there own driver check utility which should search your computer for all of their own drivers and download install the updated ones. You can try that out too.
Let me know how it goes.
Related
Hey guys,
Yep. *NOT* connecting to Kies.
I'm in Australia. Bought my SGS2 from HK (PDA ZSKG2, CSC OZSKG2), running Gingerbread 2.3.3 and is currently rooted using Chainfire's Odin dump on these forums. Prior to rooting, i had the same issue.
I have checked via the program, i have the latest kies program downloaded (2.0.2.11071_128) - and I also have installed the USB.exe file (for the propper Samsung SGS2 drivers off the Samfirmware.com website) I also have 2 mini USB cables, they are both genuine Samsung, so worst case scenario, at least 1 of these cables should work...
Aslo as an FYI: I am using a desktop PC with Windows 7 Ultimate 32bit OS (legit) - have not had issues running other USB2 devices o it...
THE PROBLEM:
When i plug in the cable, the phone immediately tried to connect to Kies (on ym SGS1, i had the option of Kies/media player/mass storage) but can't select anymore; when i connect, a pop-up box shows up "I9100" and asks me what program i want to use - i have ano problems with copy/paste/delete/transferring files using this method, the issue is with Kies.
When i open kies manually and plug in the phone+USB cable (or if Kies starts up automatically when cable is plugged in), it jsut gets stuck on "CONNECTING", but the phone itself never actually connects.
I have tried reinstalling the same usb.eve drivers again, restarting PC, the phone, unplug/replug in the cable and it doesn't seem to work...the funny thing, was my riisted SGS1 phone connected ti kies instantly and never had any issues with it. Can anyone lend me a hand or some advice? At the moment, i just want a simple Uuser firendly interface for restoring a tonne of my saved contats in a contacts file logged backed up form my old phone.
Cheers
RoOSTA
Mine requires USB debugging disabled before connecting.
Sent from my GT-I9100 using XDA Premium App
As i said, it works without KIes, but wonr work with it.
If i turn on USB debugging, plug in the USB cable, the error "Reconnect the device on Samsung Kies (PS Studio) mode. Current connection mode is not supported by Kies"
Any other ideas?
I might have missed exactly what you'd done, but did you actually try with USB debugging disabled / off?
Sent from my GT-I9100 using XDA Premium App
UpInTheAir said:
I might have missed exactly what you'd done, but did you actually try with USB debugging disabled / off?
Sent from my GT-I9100 using XDA Premium App
Click to expand...
Click to collapse
It should work ! Do u use a custom rom ?
Double check USB Debugging is OFF.
Then check if you have one of those "multi mount" apps active that let you use /sdcard from phone and PC simultaniously - kill it.
Usb debug on or off makes no difference guys. Im using stock firmware, just rooted kernel...and no multi-use apps...or at least I dont think (what kind exactly?)
roosta said:
Hey guys,
Yep. *NOT* connecting to Kies.
I'm in Australia. Bought my SGS2 from HK (PDA ZSKG2, CSC OZSKG2), running Gingerbread 2.3.3 and is currently rooted using Chainfire's Odin dump on these forums. Prior to rooting, i had the same issue.
I have checked via the program, i have the latest kies program downloaded (2.0.2.11071_128) - and I also have installed the USB.exe file (for the propper Samsung SGS2 drivers off the Samfirmware.com website) I also have 2 mini USB cables, they are both genuine Samsung, so worst case scenario, at least 1 of these cables should work...
Aslo as an FYI: I am using a desktop PC with Windows 7 Ultimate 32bit OS (legit) - have not had issues running other USB2 devices o it...
THE PROBLEM:
When i plug in the cable, the phone immediately tried to connect to Kies (on ym SGS1, i had the option of Kies/media player/mass storage) but can't select anymore; when i connect, a pop-up box shows up "I9100" and asks me what program i want to use - i have ano problems with copy/paste/delete/transferring files using this method, the issue is with Kies.
When i open kies manually and plug in the phone+USB cable (or if Kies starts up automatically when cable is plugged in), it jsut gets stuck on "CONNECTING", but the phone itself never actually connects.
I have tried reinstalling the same usb.eve drivers again, restarting PC, the phone, unplug/replug in the cable and it doesn't seem to work...the funny thing, was my riisted SGS1 phone connected ti kies instantly and never had any issues with it. Can anyone lend me a hand or some advice? At the moment, i just want a simple Uuser firendly interface for restoring a tonne of my saved contats in a contacts file logged backed up form my old phone.
Cheers
RoOSTA
Click to expand...
Click to collapse
Im in Mexico and I also bought my Galaxy S 2 in HK and Kies is working perfect on my mac. I don't have my phone rooted so maybe its that.
Not sure if that matters, but normally you install phone drivers from Kies
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
As I said before rooting unable to connect... No other ideas??
Top..
???
roosta said:
Top..
???
Click to expand...
Click to collapse
really...? problem that uncommon?
I had problems connecting with kies too.
Make sure your s2 screen is turned on and unlocked
during the connection period, somehow that affected.things with me.
also reinstall kies, that may help. I think I also removed the samsung device in the device manager to force windows to reinstall the drivers.
Sent from my GT-I9100 using XDA App
Thanks, i'll give thgat a try when i get home. However, i now have a strong hunch i could have a phone with either faulty software or hardware:
When i plug a USB cable into my work PC to simple recharge the phone (exiting any PC Kies attempt by the phone) the stupid device tells me it cannot recharge due to the phone or batteries TEMPERATURE being too high or too low; yet the phone is not warm at all, and the room temperatures are more than optimal for its operating environmement.
Tried unplugging and plugging back in and get the same error, am going to turn the phone off now and attempt to recharge it. Dodgy HK crap....
RoOSRA
Some quick suggestions:
* Plug the cable into the usb port in the back of the computer, not the front port or usb hub (unless it's an AC powered hub).
* Make sure you use the Samsung micro-usb cable that came with the phone
* Try with another computer, maybe the PC drivers are messed up. Uninstall them as I mentioned above.
* Try to factory reset the phone
* Change your ROM to an official Samsung one
EDIT: Regarding temperature, there are tools in the market that can show you battery temp. Regarding the message you're getting, it would be useful to show a screenshot. If I remember correctly, Power+Home shortcut will take a screenshot.
So I have the OTA ICS update now. I want root again (didn't have it previously on this phone), so I decided I would try one of the "1-click" scripts. My problem now lies in my PC (win 7 64bit) and drivers I think. Downloaded the motorola utility to get all my correct drivers. When I plug up my phone, my pc downloads all the drivers, but it never downloads the Mot ADB interface one. I'm stumped. I've tried it on all 3 machines. I can transfer files and the phone mounts ok OTHER THAN the adb interface.
When I run adb shell it says "error: device not found"
Here's what I have done.
1. Uninstalled all my drivers
2. Re-installed all the drivers
3. Tried every USB port on the computer
4. Made sure USB Debugging was checked
5. Made sure my phone was in Media mode
6. Wiped cache and data
7. Tried it on other machines
8. Re-installed windows on 1 machine.
When I put the phone in AP Fastboot, then and ONLY then will the PC see the phone as an adb interface.
Any thoughts?
I think you need to switch it to a pc mode other people have said.
Sent from my GT-I9300 using xda premium
You use USB 2.0 ports?
Zanith said:
I think you need to switch it to a pc mode other people have said.
Sent from my GT-I9300 using xda premium
Click to expand...
Click to collapse
on the new ICS update there isn't a PC mode.
HSD-Pilot said:
You use USB 2.0 ports?
Click to expand...
Click to collapse
yes.
Here's what my device manager looks like. As you can see, it has NO option of ADB anywhere! Thinking it might be this phone.
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
jdenman03 said:
Here's what my device manager looks like. As you can see, it has NO option of ADB anywhere! Thinking it might be this phone.
Click to expand...
Click to collapse
This is what you should see:
pedrotorresfilho said:
This is what you should see:
Click to expand...
Click to collapse
You are correct. But its not prompting me even to install the adb interface. Thus the reason why I feel as though it is the phone and not the PC's. I run adb on my other phones just well.
Try typing
start adbd
In terminal emulator in your phone?
Sent from my GT-I9300 using xda premium
I'm going to assume you tried this link to get the drivers:
http://forum.xda-developers.com/showthread.php?t=1539192
If not, uninstall all the drivers you have currently and reboot and then go to the link above and get the Moto drivers and RSD Lite.
Another link is here which really gets in-depth on getting ADB to function:
http://www.droidrzr.com/index.php/t...find-out-how-to-manipulate-your-system-files/
Zanith said:
Try typing
start adbd
In terminal emulator in your phone?
Sent from my GT-I9300 using xda premium
Click to expand...
Click to collapse
this doesn't do anything.
iBolski said:
I'm going to assume you tried this link to get the drivers:
http://forum.xda-developers.com/showthread.php?t=1539192
If not, uninstall all the drivers you have currently and reboot and then go to the link above and get the Moto drivers and RSD Lite.
Another link is here which really gets in-depth on getting ADB to function:
http://www.droidrzr.com/index.php/t...find-out-how-to-manipulate-your-system-files/
Click to expand...
Click to collapse
tried this and still failed. I've done it now on 5 machines. All have the same issue. None of them ever prompt me to install drivers for adb interface. terminal emulater doesn't do anything on my phone either. Bout to take my phone to verizon.
OK I am running emulator on my phone, and when I enter command "adb shell" adb starts and still says "error: device not found"
gonna throw this phone to the wall. Thanks for all the suggestions and help thus far. If I can't get it fixed by tonight, i'll take it to verizon tomorrow and have them send me a replacement.
EDIT: Plugged in my wife's razr with usb debugging and everything worked correctly. DEFINITELY the phone! Can't believe I have wasted this past 2 days on this!
I am having the SAME EXACT problem running the same version of Windows. I'm guessing you haven't found a work around as of yet, eh? I still have been unable to get Windows to recognize the ADB interface. Whenever I connect my Bionic, it finds/installs it just fine, but not so much with the Razr Maxx.
Have you attempted a factory reset at all? The issue began with me because I rooted the device, used OTA rootkeeper, installed the OTA, but then Rootkeeper was unable to restore root, so I also tried to use the 1-click scripts.
jdenman03 said:
OK I am running emulator on my phone, and when I enter command "adb shell" adb starts and still says "error: device not found"
gonna throw this phone to the wall. Thanks for all the suggestions and help thus far. If I can't get it fixed by tonight, i'll take it to verizon tomorrow and have them send me a replacement.
EDIT: Plugged in my wife's razr with usb debugging and everything worked correctly. DEFINITELY the phone! Can't believe I have wasted this past 2 days on this!
Click to expand...
Click to collapse
I had the same issue.. You need to download Matts utility 1.7 and then extract the zip into an (empty) folder. Then click the first file in your folder and click on the 64 bit. Let it install then run the utility.. Make sure your device is in USB debugging mode and that you have your storage device set to mtb.. Then click the root android 4.0.4 option and let the program to the rest! I hope this helps it sure helped me.
Sent from my DROID RAZR using xda app-developers app
I had a very similar issue that was stopping me from re-rooting after I pulled the official OTA. At the end of it, my problem seemed to also center on not having the Mot Composite ADB Interface driver install when I connected the device by USB. I was running Moto Drivers ver. 5.7.0 (current) and successfully connected on other RAZRs, just not my current one. Same 'device not found' errors.
Connecting my device as a camera (PTP) fixed the problem (settings -> storage -> press the menu key and choose Camera (PTP). After doing that, windows installed the additional devices: USB Composite Device, DROID RAZR, and Mot Composite ADB Interface and I was back on track. Regardless of what I tried otherwise (including a wipe data) the ADB interface just wouldn't install until I connected as a camera.
My post is here:
http://forum.xda-developers.com/showthread.php?t=1743367&highlight=root+ota&page=2
EDIT: Just re-read the OP. Not just close. Sounds like you're having the SAME problem. Hope this helps.
At first I could not get this script to work. Apparently I had no ADB interface installed. What did the trick for me, was switching off the USB debugging, plugging in my Droid 4 a few times in camera, MTP and mass storage mode. That made my computer install all the necessary drivers.
Having done this, it all worked perfectly. Thank you very much! I am completely new to Android and XDA, and this almost foolproof script is excellent. :good:
So simple..
Had same problems with my new phone as everyone else, PC not recognizing ADB .... tried downloading a couple of different things from other advice as I don't know much about computers this just got confusing. All I had to do was turn off the USB debugging, plug in under the different USB computer connections and ta da!
No Storage Drives Show
Hi everyone.
First time I post on the forum, although I've been using it for quite some time.
This time I'm experiencing an annoying situation with which I spent many hours of my last two days.
Turns out my Windows (7 64-bit) won't display the mass storage drives from my Droid Razr (XT910 Model, Brazilian Carrier OTA).
The funny thing is that all Motorola Drivers are shown on Device Manager and when in AP Fastboot Mode, RSD will recognize the phone as connected and flash normally.
I am really out of ideas here. Did religiously everything written on this forum and many others:
Tried different cables and pcs
ReInstalled ICS OTA
Wiped cache/data
Factory Reset from Android
Tried to connect as Camera, Media and Mass Storage
Tried with USB Debugging both on and off
One thing that may have caused the problem, from what I recall, is I am running without the cid file, as I deleted it to install JellyBean through the steps suggested by "TheRazRGuy" here on xda.
Thing is, as I don't have the cid, I must boot through BPTools on bootmanager everytime the system is turned on. After I downgraded the JellyBean to ICS OTA again, I went on to root the device but forgot about the boot requirement I described.
After the easyroot first reboot, the screen went black as always when normal reboot without cid. Even though easyroot still rebooted 2 more times and displayed the "your phone is rooted" message, I thing something may have gone wrong on this process.
It is worth saying that with JB the mass storage was being shown and before the easyroot process too..
I am really out of clues here, hope someone can help!
Found a solution on another thread:
http://forum.xda-developers.com/showthread.php?p=36543010#post36543010
Just had to modify an option on BootMenu Manager
Don't know what's happening, but my windows 8.1 laptop refuses to recognize my xperia mini pro when in fastboot. Literally had no problem when flashing kernels in my old windows 7 laptop. Tried literally everything I can think of.
1. disable driver signature verification in win 8.1
2. install all drivers from flashtool (interestingly I do not see sk17i in the device list maybe that's the problem)
3.install drivers from pc companion (connects normally in media transfer, but not in fastboot)
4.installed andriod sdk
5.modified win_usb file with sony's version (my laptop doesn't prompt me to install drivers when I plug my mini pro in fastboot)
6. turned off mtp mode and turned on debugging.
Additional info: my mini pro is running pac man 4.3
What else am I'm missing? This is basically my last resort after hours of searching. I will be extremely grateful for any assistance.
cs098 said:
Don't know what's happening, but my windows 8.1 laptop refuses to recognize my xperia mini pro when in fastboot. Literally had no problem when flashing kernels in my old windows 7 laptop. Tried literally everything I can think of.
1. disable driver signature verification in win 8.1
2. install all drivers from flashtool (interestingly I do not see sk17i in the device list maybe that's the problem)
3.install drivers from pc companion (connects normally in media transfer, but not in fastboot)
4.installed andriod sdk
5.modified win_usb file with sony's version (my laptop doesn't prompt me to install drivers when I plug my mini pro in fastboot)
6. turned off mtp mode and turned on debugging.
Additional info: my mini pro is running pac man 4.3
What else am I'm missing? This is basically my last resort after hours of searching. I will be extremely grateful for any assistance.
Click to expand...
Click to collapse
even i faced the same problem... the problem is not due to device drivers, its due to WINDOWS 8.1
microsoft have changed the working of USB controller.....microsoft may release patch for it....i reverted back to win7
i came across many fourms discussing abt the same problem.
try this .. it may help..
http://forum.xda-developers.com/showpost.php?p=44288852&postcount=24
but it dint helped me though
kaarthi said:
even i faced the same problem... the problem is not due to device drivers, its due to WINDOWS 8.1
microsoft have changed the working of USB controller.....microsoft may release patch for it....i reverted back to win7
i came across many fourms discussing abt the same problem.
try this .. it may help..
http://forum.xda-developers.com/showpost.php?p=44288852&postcount=24
but it dint helped me though
Click to expand...
Click to collapse
The weird thing is my new phone (xperia m) works fine with 8.1, flashing kernels, roms and what not,
Utterly confused lol.
cs098 said:
The weird thing is my new phone (xperia m) works fine with 8.1, flashing kernels, roms and what not,
Utterly confused lol.
Click to expand...
Click to collapse
such a weird thing ......
but my st15i wont work with win 8.1 ..!!!
kaarthi said:
such a weird thing ......
but my st15i wont work with win 8.1 ..!!!
Click to expand...
Click to collapse
the 2011 xperia's must be incompatible or something :/
cs098 said:
the 2011 xperia's must be incompatible or something :/
Click to expand...
Click to collapse
I think that the problem in not only with 2011 xperias but also with 2012 xperias.... this is what i found while searching for solution... seems like there is no solution yet....
http://forum.xda-developers.com/showthread.php?t=2491455
http://forum.xda-developers.com/showthread.php?t=2410010
http://forum.xda-developers.com/showthread.php?t=2508066
only solution is to change the OS
kaarthi said:
I think that the problem in not only with 2011 xperias but also with 2012 xperias.... this is what i found while searching for solution... seems like there is no solution yet....
http://forum.xda-developers.com/showthread.php?t=2491455
http://forum.xda-developers.com/showthread.php?t=2410010
http://forum.xda-developers.com/showthread.php?t=2508066
only solution is to change the OS
Click to expand...
Click to collapse
luckily I now have a 2013 xperia
Well, I rooted, flashed, fastbooted (and everything else) my sk17i on my Windows 8.
I don't believe that they changed something as deep as the USB drivers/protocols whatever to 8.1
I takes many times dough, to make it.
1st. you should have the driver signing disabled on Windows
2nd. you connect the device and it asks for the drivers
3rd. you install the drivers while the fastboot ends
4th. you try again and it luckily will work.
As a tip keep "Device Manager" on Windows opened and enable "View\Show Hidden Devices" so that you can see the grayed uninstalled driver.
n.inacio said:
Well, I rooted, flashed, fastbooted (and everything else) my sk17i on my Windows 8.
I don't believe that they changed something as deep as the USB drivers/protocols whatever to 8.1
I takes many times dough, to make it.
1st. you should have the driver signing disabled on Windows
2nd. you connect the device and it asks for the drivers
3rd. you install the drivers while the fastboot ends
4th. you try again and it luckily will work.
As a tip keep "Device Manager" on Windows opened and enable "View\Show Hidden Devices" so that you can see the grayed uninstalled driver.
Click to expand...
Click to collapse
Well I did all of that if you read the first post.
So you're saying sometime it doesn't take and you have it do it repeatedly?
Okay Will try
cs098 said:
Well I did all of that if you read the first post.
So you're saying sometime it doesn't take and you have it do it repeatedly?
Okay Will try
Click to expand...
Click to collapse
What I'm saying is that the hard part is to get the drivers working.
To install them you only have this "ghost" driver request on the device manager that you can only see if you enable the "show hidden devices".
It took me many tries and errors to get it right.
Another thing I just remenber: if you installed a bad driver it will also not work, so wen you want to install a new one you have do unistall the previous wtih the option of "deleting the files from your computer". This from device manager, of course.
If I could do it then it's possible, right?
windows 8 + usb 3.0 = problem (maybe)
Maybe the problem is windows 8 with usb 3.0 driver
http://forum.xda-developers.com/showthread.php?t=2256359
My device is not detected by the flashtool...debugging and unknown resources are checked, its turned on and still, not working..all the drivers have been installed...pls help..
Sent from my SK17i using xda premium
Kit Kat now up, want a piece of the action.
Nothing works
Bump.
this one works for me.
Code:
http://www.droid-now.com/2013/10/fix-working-fastboot-drivers-windows-8-1-x64/
I use the latest one with the mentioned two "modded" inf files in the previous link.
Code:
http://www.intel.com/p/en_US/support/highlights/sftwr-prod/usb3ehcd
just remember to plug the usb cable into USB 3.0 port
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Click to expand...
Click to collapse
ceroberoz said:
this one works for me.
Code:
http://www.droid-now.com/2013/10/fix-working-fastboot-drivers-windows-8-1-x64/
I use the latest one with the mentioned two "modded" inf files in the previous link.
Code:
http://www.intel.com/p/en_US/support/highlights/sftwr-prod/usb3ehcd
just remember to plug the usb cable into USB 3.0 port
Click to expand...
Click to collapse
thanks will try
So I tried searching google and the forums and found nothing.
So on multiple PC's it will charge my DNA but it will not detect it in device manager, like it's not plugged in at all. Almost like it's not seeing any RX/TX Just VCC and Ground. I've tried 3 different Pc's and probably 10 different USB cables. Multiple roms and it will not even see it in bootloader. Not sure if anyone else has experienced this issue, it's been going on for months, I can do pretty much everything without USB access to my phone but if I want to RUU I'm going to be SOL.
Any thoughts?
yutsoku said:
So I tried searching google and the forums and found nothing.
So on multiple PC's it will charge my DNA but it will not detect it in device manager, like it's not plugged in at all. Almost like it's not seeing any RX/TX Just VCC and Ground. I've tried 3 different Pc's and probably 10 different USB cables. Multiple roms and it will not even see it in bootloader. Not sure if anyone else has experienced this issue, it's been going on for months, I can do pretty much everything without USB access to my phone but if I want to RUU I'm going to be SOL.
Any thoughts?
Click to expand...
Click to collapse
What operating system are u using? I started a thread about windows 8 not seeing the dna in bootloader. it happens because htc has not updated the drivers for windows 8
heres the link http://forum.xda-developers.com/showthread.php?t=2521504
Win7 and linux... Think its a phone issue. Well I'm 99% sure
Sent from my HTC6435LVW using Tapatalk
Do you have drivers installed and can you boot into recovery and mount ur device? You may need adb installed. Do you have SDK drivers installed.
Another good way to get ur computer to see ur phone is to download pdanet and it will install the needed drivers to see ur phone.
thayl0 said:
Do you have drivers installed and can you boot into recovery and mount ur device? You may need adb installed. Do you have SDK drivers installed.
Another good way to get ur computer to see ur phone is to download pdanet and it will install the needed drivers to see ur phone.
Click to expand...
Click to collapse
i have done all that. i can adb into bootloader but once in bootloader the computer does not recognize the phone anymore.
thayl0 said:
Do you have drivers installed and can you boot into recovery and mount ur device? You may need adb installed. Do you have SDK drivers installed.
Another good way to get ur computer to see ur phone is to download pdanet and it will install the needed drivers to see ur phone.
Click to expand...
Click to collapse
Not quite understanding, it's not a driver issue... The PC it's self will not see the device. Not even in device manager as an unknown device, the phone it's self will not say, "Hello PC I am here, do you have my drivers?" I plug it in, get nothing as if I am using a charging cable with only VCC and ground, without RX/TX. I'm pretty positive that it's a phone issue, not a PC/Driver issue. Even if it was a driver issue I'd be getting the MTP device showing up.
yutsoku said:
Not quite understanding, it's not a driver issue... The PC it's self will not see the device. Not even in device manager as an unknown device, the phone it's self will not say, "Hello PC I am here, do you have my drivers?" I plug it in, get nothing as if I am using a charging cable with only VCC and ground, without RX/TX. I'm pretty positive that it's a phone issue, not a PC/Driver issue. Even if it was a driver issue I'd be getting the MTP device showing up.
Click to expand...
Click to collapse
Actually it could be a driver issue. There has to be a driver installed for something to notice something.
Go to device manager and look at the very top when you connect your phone does it show this?
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Or the driver could be corrupted and you tried to uninstall and reinstall
thayl0 said:
Actually it could be a driver issue. There has to be a driver installed for something to notice something.
Go to device manager and look at the very top when you connect your phone does it show this?
View attachment 2408658
Or the driver could be corrupted and you tried to uninstall and reinstall
Click to expand...
Click to collapse
Driver isn't installed on my work PC still nothing. Tried driver on work PC...still nothing :/
Sent from my HTC6435LVW using Tapatalk
yutsoku said:
Driver isn't installed on my work PC still nothing. Tried driver on work PC...still nothing :/
Sent from my HTC6435LVW using Tapatalk
Click to expand...
Click to collapse
Heres what I just had to do because my phone wasn't being seen by my pc.
http://www.youtube.com/watch?v=oaNM-lt_aHw
Do that and after boot into recovery and mout the system is should reinstall the correct driver.
Confirmed it's not drivers my phone can't see USB otg either. Probably my phone is defective
Sent from my HTC6435LVW using Tapatalk
yutsoku said:
Confirmed it's not drivers my phone can't see USB otg either. Probably my phone is defective
Sent from my HTC6435LVW using Tapatalk
Click to expand...
Click to collapse
I find that to be very rare but okay best the luck to you.
I have a completely stock Poco F1, when i got it it had the MIUI 10 and everything was working fine. I don't plug my phone on my PC with the USB cable so much so only last week i realized its USB communication is not working at all
The only thing that changed was the official update to MIUI 11.0.5.0.
It fast charges with no problem using only the stock charger and cable. But when i plug it on the computer it spams USB not recognized on Windows 10 and no message about USB options shows on the phone at all
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
I only see the charging indication. On the USB communication options it shows the phone isn't connected to the USB.
Developer options for default USB dont matter (tried all of them - Transfer Files, Tethering, etc)
Already tried other cables and other PCs and no changes whatsoever.
I already bought and exchanged the USB board that goes at the bottom of the phone and the same thing still happens
ADB doesn't recognize the phone at all
What should i do? Please some advice (i cant even flash ROMs and other stuff like that)
Reinstall pc usb driver
Adidas108 said:
Reinstall pc usb driver
Click to expand...
Click to collapse
it doesn't matter what i install or reinstall... i tried the Mi Suite, ADB drivers from windows update and internet... 3 different PCs...
It shows like no device is connected at all.. the PC doesn't see the F1 and the F1 doesnt know its connected as well (only charges)
this is miui bug i have same issue on linux everything its okey
Your cable broken. Use another usb C cable, and try connect to another PC
ipfalvim said:
it doesn't matter what i install or reinstall... i tried the Mi Suite, ADB drivers from windows update and internet... 3 different PCs...
It shows like no device is connected at all.. the PC doesn't see the F1 and the F1 doesnt know its connected as well (only charges)
Click to expand...
Click to collapse
Try different usb port,try different usb cable,try restart windows,try clean up all usb data about connected devices (Google it), at last try different rom to see if issue still persist ...
ZjemCiKolege said:
this is miui bug i have same issue on linux everything its okey
Click to expand...
Click to collapse
Yep, IDK what's the deal with Windows but in Ubuntu 18.04, my phone just detected as MTP device, no set-up needed. In Windows, needs manual MTP driver installation using device manager.
I'll try on Ubuntu and see what happens.. But it's weird that not even the phone knows it's connected
Alvian_P said:
Your cable broken. Use another usb C cable, and try connect to another PC
Click to expand...
Click to collapse
I used 3 different cables on 3 different PCs
Check for build up dust in your USB port of the phone. Clean it carefully with a toothpick
I had this issue recently too with my fully stock Poco 11.05. My phone would either not connect with PC or would keep spamming connect and disconnect. I went to the service center for a different issue and just told them to also clean the USB port. They cleaned the port with rubbing alcohol and fixed the other issue too. No charge... Even out of warranty.
Everything works as it should now.
Also if you eliminate all issues... My last word of advice is try connecting device to Intel motherboard and not AMD.
GreenParr0t said:
Check for build up dust in your USB port of the phone. Clean it carefully with a toothpick
Click to expand...
Click to collapse
as i said on the 1st post, i replaced the entire USB board and nothing.
i didn't have the time to test the ubuntu yet but i'm almost sure its some bug on the MIUI 11
I'll try to put the other USB board again. I tried to plug-in on an amd motherboard and the phone doesn't even show up as a device.
any update??
Any update? Same problem here.
Changed USB board too. But im on MAC and still not recognized. In windows got the same error..
I can only charge, No ADB/Fastboot/USB connection
Hi,
i am on MIUI Global 11.0.8 and today i ran into this issue as well.
I got two different cables here at hand. Both are type C to type A adapter cables, but from different manufacturers.
If i use these with the F1 and connect to my laptop (ports are 3.1 capable), one cable is working fine (charging and connection) the other one is not (only charging).
Both cables are data cables and worked fine during a cross check with another phone.
Another information i found somewhere is to tweak the Windows registry, but i guess this won't solve the issue.
In the end i did a cross check with a Linux PC and same here.
So it seems to me, that it might be related to the kernel/system used for MIUI 11.
Could anyone confirm, if there are any related issues with a custom ROM, e.g. Lineage OS?
EDIT: O.k. checked it myself... i observed the same behaviour with LOS 17.1... seems the F1 doesn't like specific cables.
Tried another connection wit a true type C connector cable from the phone to the laptops type C receptacle, no problems here.
So it seems it has nothing to do with USB 3.1 hardware in the laptop, but some cables simply don't work...
Cheers,
scholbert
No solution yet?
:sad:
scholbert said:
Hi,
i am on MIUI Global 11.0.8 and today i ran into this issue as well.
I got two different cables here at hand. Both are type C to type A adapter cables, but from different manufacturers.
If i use these with the F1 and connect to my laptop (ports are 3.1 capable), one cable is working fine (charging and connection) the other one is not (only charging).
Both cables are data cables and worked fine during a cross check with another phone.
Another information i found somewhere is to tweak the Windows registry, but i guess this won't solve the issue.
In the end i did a cross check with a Linux PC and same here.
So it seems to me, that it might be related to the kernel/system used for MIUI 11.
Could anyone confirm, if there are any related issues with a custom ROM, e.g. Lineage OS?
EDIT: O.k. checked it myself... i observed the same behaviour with LOS 17.1... seems the F1 doesn't like specific cables.
Tried another connection wit a true type C connector cable from the phone to the laptops type C receptacle, no problems here.
So it seems it has nothing to do with USB 3.1 hardware in the laptop, but some cables simply don't work...
Cheers,
scholbert
Click to expand...
Click to collapse
What is the brand of cable that worked for connectivity on your poco f1, i am having the same issue with mine. Also does the serial number in your device match the one on the box?
The same thing was happening to me, my pocophone sometimes charged and sometimes not, the PC detected it sometimes, I had to disconnect the cable and reconnect, I thought the USB port was dying This happened to me on my 11.0.8, I tried other roms and the same thing happened. Then my pocophone was updated to miui 11.0.9 And now it seems to work normally, I no longer have any problems with charging or with the PC
Is your serial number saying "unknown"?