[Q] Firmware flashing for same CID, with S-ON - AT&T HTC One (M8)

Hello people,
I've been using Nexus devices for a while on which rooting/flashing/updating was far simpler than my new phone - HTC One M8. I have been researching for around 2 months now and still have not been able to come to a clear-cut solution to my problem.
I am currently on 4.4.2 and my CID is CWS_001, I am S-On and firewater did not work - before going for sunshine, I want to know if it is possible for me to update my firmware in order to flash 4.4.4 and above ROMs. I tried flashing a newer ROM but its boot up time was huge and performance was lagging as well, after research I found out that I need to update firmware for it.
Now, I do not even know which firmware I currently am on since there is too much going on in HTC One M8's forums for a new person to get a grip of things. If any one from the XDA community could clarify and simplify things for me, I would be highly grateful.
Thank you.

Cannot flash firmware without being s-off, more than likely you are on either 1.58.502 or 2.23.502 if you took the ota before it was pulled.

Untamed Fantasy said:
Now, I do not even know which firmware I currently am on since there is too much going on in HTC One M8's forums for a new person to get a grip of things. If any one from the XDA community could clarify and simplify things for me, I would be highly grateful.
Click to expand...
Click to collapse
Hboot 3.16 = 1.12, 1.54, or 1.58 firmware
Hboot 3.18 = 2.23 firmware
With 1.x firmware, you can only run ROMs based on 1.x software (otherwise experience long boot times and/or broken WiFi).
Similarly, on 2.23 firmware, you can only run ROMs based on 2.x software
EDIT: Corrected the hboot numbers. Sorry for the typos!

Thank you for the response guys. I just booted into fastboot to check my HBOOT and it says "HBOOT-3.16.0.0000".
That does not match with any of the two options posted in the previous post. I am trying to identify my current HBOOT and firmware in order to flash a ROM which matches these IDs. Do you have any suggestions as to what I should do to determine the two?

Untamed Fantasy said:
Hello people,
I've been using Nexus devices for a while on which rooting/flashing/updating was far simpler than my new phone - HTC One M8. I have been researching for around 2 months now and still have not been able to come to a clear-cut solution to my problem.
I am currently on 4.4.2 and my CID is CWS_001, I am S-On and firewater did not work - before going for sunshine, I want to know if it is possible for me to update my firmware in order to flash 4.4.4 and above ROMs. I tried flashing a newer ROM but its boot up time was huge and performance was lagging as well, after research I found out that I need to update firmware for it.
Now, I do not even know which firmware I currently am on since there is too much going on in HTC One M8's forums for a new person to get a grip of things. If any one from the XDA community could clarify and simplify things for me, I would be highly grateful.
Thank you.
Click to expand...
Click to collapse
Did you try firewater before it was discontinued or is it still available for you?

I tried it around two months back and got message that it is not possible to attain S-OFF. Tried a couple of times again later too but same outcome.

I am in the same situation as the OP, only difference is that I have S-OFF from Sunshine.. Just got my phone. I hope to follow along as you guys help him out.

Untamed Fantasy said:
Thank you for the response guys. I just booted into fastboot to check my HBOOT and it says "HBOOT-3.16.0.0000".
That does not match with any of the two options posted in the previous post. I am trying to identify my current HBOOT and firmware in order to flash a ROM which matches these IDs. Do you have any suggestions as to what I should do to determine the two?
Click to expand...
Click to collapse
Sorry bud, my bad. Typo on my previous post. It should be:
Hboot 3.16 = 1.12, 1.54, or 1.58 firmware
Hboot 3.18 = 2.23 firmware
---------- Post added at 11:28 AM ---------- Previous post was at 11:20 AM ----------
Untamed Fantasy said:
I am currently on 4.4.2 and my CID is CWS_001, I am S-On and firewater did not work - before going for sunshine, I want to know if it is possible for me to update my firmware in order to flash 4.4.4 and above ROMs.
Click to expand...
Click to collapse
Back to the core question: NO you cannot update your firmware by any "official" means at this time, with your current configuration (s-on). There is no AT&T update that contains 3.x firmware. To update the firmware by "unofficial" means you need s-off.
S-off by sunshine, then update the firmware as outlined in the thread below:
http://forum.xda-developers.com/att-htc-one-m8/development/att-4-4-3-2-22-1540-3-debloated-sense-6-t2837365
---------- Post added at 11:29 AM ---------- Previous post was at 11:28 AM ----------
badbwoydes said:
I am in the same situation as the OP, only difference is that I have S-OFF from Sunshine.. Just got my phone. I hope to follow along as you guys help him out.
Click to expand...
Click to collapse
Since you are already s-off, just follow the instructions in the thread I linked above to update firmware.

Related

[Q] Firmware/Software/radio

I am new to HTC as a whole. And I'm sorry if I'm missing something here. I've been spending my time reading the past couple of days trying to learn about this all.
It is mentioned but I never found a good explanation of CID and how it is relevant to anything that I have control over?
I'm currently running Trickdroid and I don't understand all of this 1.29 talk. From what I'm gathering from reading you can flash the Rom but it will not update things like the radio? Ok, How do I check my firmware/radio? version I am currently running?
Specifically am I reading beginning of dev posts and don't need to worry about this anymore because you wonderful devs have found a way to incorporate all this in just flashing a Rom?
Feeling a little overwhelmed coming from a Samsung device to all of this. So far so good, but confused and any help would be greatly appreciated..
Thank you in advance.
Dex954 said:
I am new to HTC as a whole. And I'm sorry if I'm missing something here. I've been spending my time reading the past couple of days trying to learn about this all.
It is mentioned but I never found a good explanation of CID and how it is relevant to anything that I have control over?
I'm currently running Trickdroid and I don't understand all of this 1.29 talk. From what I'm gathering from reading you can flash the Rom but it will not update things like the radio? Ok, How do I check my firmware/radio? version I am currently running?
Specifically am I reading beginning of dev posts and don't need to worry about this anymore because you wonderful devs have found a way to incorporate all this in just flashing a Rom?
Feeling a little overwhelmed coming from a Samsung device to all of this. So far so good, but confused and any help would be greatly appreciated..
Thank you in advance.
Click to expand...
Click to collapse
Radio aka baseband is almost never included in a ROM.
CID is carrier ID and every phone HTC makes has one. CID is what prevents you from installing say a UK carrier's official RUU on your At&T device.
HTC also utilizes something called SuperCID which is a carrier ID of 111111111 which allows you to install any firmware on your device. The only way at this time to get superCID is to gain S-off which is a security measure that restricts which parts of the phone software you can change.
With the HTC One, HTC changed what you have access to with an unlocked bootloader, previously, even with an unlocked bootloader you couldn't flash a kernel or a radio via recovery, now you can flash insecure kernels and HTC signed (approved) radios.
For flashing purposes, you can ignore the firmware requirements and flash the ROMs in the international section without issues.
gunnyman said:
Radio aka baseband is almost never included in a ROM.
CID is carrier ID and every phone HTC makes has one. CID is what prevents you from installing say a UK carrier's official RUU on your At&T device.
HTC also utilizes something called SuperCID which is a carrier ID of 111111111 which allows you to install any firmware on your device. The only way at this time to get superCID is to gain S-off which is a security measure that restricts which parts of the phone software you can change.
With the HTC One, HTC changed what you have access to with an unlocked bootloader, previously, even with an unlocked bootloader you couldn't flash a kernel or a radio via recovery, now you can flash insecure kernels and HTC signed (approved) radios.
For flashing purposes, you can ignore the firmware requirements and flash the ROMs in the international section without issues.
Click to expand...
Click to collapse
Ok. Thank you for that explanation. How do I check what radio/baseband I am currently using? RUU, though it can still not be changed because we have no s_off, what is it? I
Also how do I find out what CID I am?
Thank you again..
Dex954 said:
Ok. Thank you for that explanation. How do I check what radio/baseband I am currently using? RUU, though it can still not be changed because we have no s_off, what is it? I
Also how do I find out what CID I am?
Thank you again..
Click to expand...
Click to collapse
your CID if you have an AT&T HTC One is CWS_001
radio version can be found in about phone.
gunnyman said:
your CID if you have an AT&T HTC One is CWS_001
radio version can be found in about phone.
Click to expand...
Click to collapse
Ok would this be considered up to date? Why would I need to lock the bootloader again in order to update the firmware if I can just flash a Rom and it updates it for me?
Dex954 said:
Ok would this be considered up to date? Why would I need to lock the bootloader again in order to update the firmware if I can just flash a Rom and it updates it for me?
Click to expand...
Click to collapse
you are up to date, and there's no need to relock the bootloader and revert to stock for an update UNLESS HTC releases a new HBOOT (the bootloader) and the developers here will let you know if and when that's necessry
gunnyman said:
you are up to date, and there's no need to relock the bootloader and revert to stock for an update UNLESS HTC releases a new HBOOT (the bootloader) and the developers here will let you know if and when that's necessry
Click to expand...
Click to collapse
One last question as it seems you would know. Is there a thread on the s-off process and how that is coming? Or is that just background dev?
I'm sure it's being worked on by someone.

4.3 JB ruu will NOT save you after you upgrade hboot

Edited for accuracy:
For those happy folks finally moving to 4.4.2 (Verizon and Sprint most recently) please keep in mind that we do NOT yet have an ruu for 4.4.2. If you are S-ON you will NOT be able to save yourself using any 4.3 ruu if you have updated your hboot. Keep in mind an hboot can be flashed without any other part of an update so make sure you know what you are doing and what you have done to your device.
Just a public service announcement to hopefully bring people back to reality before they go modding their new 4.4.2 goodness.
Can't 4.4's hboot replace itself with the RUU's hboot,
(like usual 2 pass RUU install)?
Or did you mean for S-ON devices?
Im sure some magic can be worked for those that are s-off and can flash non encrypted. S-on folks definitely have to watch out. Overall its just best that people think before they play.
Jiggity Janx said:
Im sure some magic can be worked for those that are s-off and can flash non encrypted. S-on folks definitely have to watch out. Overall its just best that people think before they play.
Click to expand...
Click to collapse
S-off should download. Might have to test lol
Sent from my HTC6600LVW using Tapatalk
Aren't the s-off'ed and unlocked devices able to use their respective RUU's to downgrade? Example like myself I wen't from 1.11.605.4 official to the new 2.16.605.2 that if I ran in to a problem I could do the 0P3PIMG.zip from SD method or do the fastboot oem rebootRUU with the vzw.t6.0P3PIMG_1.11.605.4.zip and I was under the impression we could downgrade or upgrade as we see fit so long as we are s-off??? Isn't that how it's always been? I thought s-on users only really had to be careful since they could only upgrade due to main version issue and also not having a KitKat RUU now available if they took the update while s-on.... Some clarity would be great! Honestly though I thought the way I just worded it is how it's always been with HTC devices...
Jiggity Janx said:
Im sure some magic can be worked for those that are s-off and can flash non encrypted. S-on folks definitely have to watch out. Overall its just best that people think before they play.
Click to expand...
Click to collapse
ALL of this discussion is why I started this thread!
It is important we get to the complete truth. IMO my OP stands valid until we have confirmation otherwise.
Jiggity Janx said:
ALL of this discussion is why I started this thread!
It is important we get to the complete truth. IMO my OP stands valid until we have confirmation otherwise.
Click to expand...
Click to collapse
Last night, @waco2hot33 ran the RUU and went s-on to take the OTA...and was able to regain s-off, root, and unlocked via WeakSauce/firewater s-off...Here's how he did it
But, once you're back to s-off, and have root, no matter what hboot you have, you can run the commands from @scotty1223's thread found HERE to unlock the new hboot
End of discussion?
Yeah that's incorrect hehe... For s-on users that stands true... They need to be extremely careful until something becomes available, but speaking for the Verizon users that took the OTA and are s-off... Unlocked is NOT necessary, just as long as they are s-off they can actually downgrade back to stock 4.3 for whatever the reason may be.. i.e.: warranty, bad flash, etc etc... It's 100% always been this way for all HTC devices that are s-off... It's by far the greatest feature or perk of having an HTC device... If you don't believe me then grab the encrypted vzw.t6_1.11.605.4 RUU and run it, you will see you will have no issues downgrading. While s-on users if they attempted they would get the main version to low error, s-off bypasses that...
Jiggity Janx said:
ALL of this discussion is why I started this thread!
It is important we get to the complete truth. IMO my OP stands valid until we have confirmation otherwise.
Click to expand...
Click to collapse
Murrda said:
Yeah that's incorrect hehe... For s-on users that stands true... They need to be extremely careful until something becomes available, but speaking for the Verizon users that took the OTA and are s-off... Unlocked is NOT necessary, just as long as they are s-off they can actually downgrade back to stock 4.3 for whatever the reason may be.. i.e.: warranty, bad flash, etc etc... It's 100% always been this way for all HTC devices that are s-off... It's by far the greatest feature or perk of having an HTC device... If you don't believe me then grab the encrypted vzw.t6_1.11.605.4 RUU and run it, you will see you will have no issues downgrading. While s-on users if they attempted they would get the main version to low error, s-off bypasses that...
Click to expand...
Click to collapse
Please read my post above yours. Waco went s-on, took the update and installed it, and was able to regain s-off via the link i posted above. Therefore, one COULD root the newest update whether they are s-on or s-off.
I did something similar but why did he s-on?? Def didn't have to do that... I got the OTA and it failed 2 times so I said F it and ran the encrypted RUU just to get back to a complete stock state in case it was a boot.img or something missing issue and I remained "s-off" and "unlocked", redownloaded the OTA after booting back up and the OTA then flashed perfectly fine with booting in to KitKat and still s-off and unlocked. Only thing I had to do was fastboot TWRP back and flashed the SuperSU v1.94 and I was straight!
Did he think he needed to be s-on to take the OTA?
Vinchenzop said:
Last night, @waco2hot33 ran the RUU and went s-on to take the OTA...and was able to regain s-off, root, and unlocked via WeakSauce/firewater s-off...Here's how he did it
But, once you're back to s-off, and have root, no matter what hboot you have, you can run the commands from @scotty1223's thread found HERE to unlock the new hboot
End of discussion?
Click to expand...
Click to collapse
Murrda said:
I did something similar but why did he s-on?? Def didn't have to do that... I got the OTA and it failed 2 times so I said F it and ran the encrypted RUU just to get back to a complete stock state in case it was a boot.img or something missing issue and I remained "s-off" and "unlocked", redownloaded the OTA after booting back up and the OTA then flashed perfectly fine with booting in to KitKat and still s-off and unlocked. Only thing I had to do was fastboot TWRP back and flashed the SuperSU v1.94 and I was straight!
Did he think he needed to be s-on to take the OTA?
Click to expand...
Click to collapse
Noob moment? Tired? Acid flashback? Your guess is as good as mine, but he went s-on and was able to regain s-off via WeakSauce temp-root and firewater s-off with newest OTA/firmware. So...success? lol
I got what you are saying.. You are stating it is possible to root unlock and s-off official KitKat but what Jiggity Janx created the OP for was saying to everyone to be careful in case they soft bricked hard bricked boot looped or what have you that when on official KitKat there phone may be rendered unusable because there is no KitKat RUU.... What good is a rooted phone if you can't boot it? I was stating that if you are s-off and can at least boot to hboot that you are 100% safe and can run the Jelly Bean RUU....
Vinchenzop said:
Please read my post above yours. Waco went s-on, took the update and installed it, and was able to regain s-off via the link i posted above. Therefore, one COULD root the newest update whether they are s-on or s-off.
Click to expand...
Click to collapse
---------- Post added at 10:17 PM ---------- Previous post was at 10:15 PM ----------
But yes that is indeed good to know though, thanks for the info! Good to know s-on or off we can work with KitKat!
Verdict.....s-off allows full downgrade of everything via ruu. Firmware and hboot. Just tested myself.
Sent from my Nexus 7 using Tapatalk
Murrda said:
I got what you are saying.. You are stating it is possible to root unlock and s-off official KitKat but what Jiggity Janx created the OP for was saying to everyone to be careful in case they soft bricked hard bricked boot looped or what have you that when on official KitKat there phone may be rendered unusable because there is no KitKat RUU.... What good is a rooted phone if you can't boot it? I was stating that if you are s-off and can at least boot to hboot that you are 100% safe and can run the Jelly Bean RUU....
---------- Post added at 10:17 PM ---------- Previous post was at 10:15 PM ----------
But yes that is indeed good to know though, thanks for the info! Good to know s-on or off we can work with KitKat!
Click to expand...
Click to collapse
I understand and agree, but if you're s-on, the likelyhood of you bricking your device is nearly null. If you're s-off, you could likely use the 4.3 RUU and downgrade your hboot (i did this yesterday during a brain lapse after taking/applying the update).
So if you're looking if being s-off allows you to downgrade your hboot, then the answer is yes.
dottat said:
Verdict.....s-off allows full downgrade of everything via ruu. Firmware and hboot. Just tested myself.
Sent from my Nexus 7 using Tapatalk
Click to expand...
Click to collapse
And that's a second confirmations
LOL..... Thank you!!
dottat said:
Verdict.....s-off allows full downgrade of everything via ruu. Firmware and hboot. Just tested myself.
Sent from my Nexus 7 using Tapatalk
Click to expand...
Click to collapse
---------- Post added at 10:25 PM ---------- Previous post was at 10:24 PM ----------
OP and or title should be corrected so it is not misleading to some looking for answers... Maybe I'll make a thread for users as reference for all the variants
I think the intent of the op was really meant for the users who are currently s-on and running KitKat. If they run into issues they likely won't be able to root and s-off and will be screwed as there currently isn't public KitKat ruu available.
Good discussion. Please don't discuss the intent of the thread anymore.
Sent from my Nexus 7 using Tapatalk
What did that mean ~~~> Don't discuss the intent of the thread anymore
dottat said:
I think the intent of the op was really meant for the users who are currently s-on and running KitKat. If they run into issues they likely won't be able to root and s-off and will be screwed as there currently isn't public KitKat ruu available.
Good discussion. Please don't discuss the intent of the thread anymore.
Sent from my Nexus 7 using Tapatalk
Click to expand...
Click to collapse
Vinchenzop said:
Therefore, one COULD root the newest update whether they are s-on or s-off.
Click to expand...
Click to collapse
Vinchenzop said:
I understand and agree, but if you're s-on, the likelyhood of you bricking your device is nearly null.
Click to expand...
Click to collapse
IMO if you can root it you can f it up. So s-on users do have some risk and currently there is no fix for them on 4.4.2 where there was a fix for them on 4.3 (encrypted ruu).
Good to see that soff users should be good to use a lower version ruu to downgrade if needed.
I have updated and downgraded to the stock version OS and hboot. But I'm also S Off. I had to use the decrypted RUU file though....
TappEd from my HTC One Max
Check out my website for encouragement....
www.projectintercession.blogspot.com
Murrda said:
What did that mean ~~~> Don't discuss the intent of the thread anymore
Click to expand...
Click to collapse
Lol...I meant let's not lose sight of the warning here. Noobs will be confused.
Sent from my Nexus 7 using Tapatalk

[Q] HTC Evo 4g LTE Help

First of all please dont kill me if i am going about this the wrong way. I have tried to seach fourms here and all over the net and have yet to find a solution. I am rooted S-ON running jelly bean with viper as my daily driver. The problem is when i switch the phone to LTE/CDMA mode it disconnects and i have no connection but in CDMA only I have service. Please if I cant resolve this issue the device will be getting a bath. I would rather not if I can avoid it. Please if someone can help or at least point me in the right direction. thanks in advance.
tpitt268 said:
First of all please dont kill me if i am going about this the wrong way. I have tried to seach fourms here and all over the net and have yet to find a solution. I am rooted S-ON running jelly bean with viper as my daily driver. The problem is when i switch the phone to LTE/CDMA mode it disconnects and i have no connection but in CDMA only I have service. Please if I cant resolve this issue the device will be getting a bath. I would rather not if I can avoid it. Please if someone can help or at least point me in the right direction. thanks in advance.
Click to expand...
Click to collapse
Sounds like you haev the incorrect radio installed. Please consult your rom developer, or find a radio that works with your carrier and flash it.
The evo 4g forum here would be of help.
---------- Post added at 08:49 PM ---------- Previous post was at 08:49 PM ----------
oh, and considered your self killed. 360 no scope one in the chamber. jk
I have never messed with the radios and it worked at one time. Would that still be radios. I can't imagine if I have not messed with radios and it worked at one time if the radios are the problem. I could be wrong.
Post your baseband version and what rom update you are on and we can tell you if that is a potential issue.
And you said it used to work... How long ago? Have you flashed a rom update recently? Did it just stop out of nowhere?
Android 4.1.1
software version Viper4G 3.1.5
baseband 1.02.12.0427
please let me know if any other info is needed
Yea, that's an old radio from like almost 2 years ago. They were not known as being the most reliable for LTE stuff. If you aren't S-off then my suggestion is to relock the bootloader then RUU to the newest 4.3 (backup your storage to the PC first because I think it wipes it due to needing to repartition for the 4.3 update since the system is bigger). This has the newest radio and touchscreen firmware as well as allowing you to run newer versions of the roms you like. You'll have to redo the bootloader unlock and recovery, but it's the same process as before. If you are S-Off then you might be able to just skip the RUU and flash the firmware package only.
My hboot is 1.12.0000 I thought I read that you could flash radios with that hboot but I have not found anything to confirm this. Is that true? Would it be easier to just unroot and update or just take it all the way to S-Off and then update the radios?
Depends on what you feel more comfortable with, but I would think it would be best to do the full RUU since it's a big deal about the repartition thing. It's the reason HTC came out with the official RUU only instead of an OTA update.
Info here: http://www.androidpolice.com/2014/0...date-as-a-full-ruu-file-no-ota-update-coming/

[Q&A] AT&T Stock Backups, Recoveries, OTAs and Radio IMGs

Q&A for AT&T Stock Backups, Recoveries, OTAs and Radio IMGs
Some developers prefer that questions remain separate from their main development thread to help keep things organized. Placing your question within this thread will increase its chances of being answered by a member of the community or by the developer.
Before posting, please use the forum search and read through the discussion thread for AT&T Stock Backups, Recoveries, OTAs and Radio IMGs. If you can't find an answer, post it here, being sure to give as much information as possible (firmware version, steps to reproduce, logcat if available) so that you can get help.
Thanks for understanding and for helping to keep XDA neat and tidy!
When i resturned to stock. I only flash the stock recovery at rom. And i dont the radio. What radio does? Do i still need to flash it?
Little explanations needed !!!
Hi guys,just joined this HUGE community where you can find almost everything you need for your satisfaction:good: !
But since i`m noobie would appreciate some assistance in explaining how to unlock my M8,and install Android Revolution HD ROM !!!
I spent like 5 hours yesterday reading all kind`a info about how,where,why etc ... and the more i read,the more confused i got
Things i got to find out about my M8 = *software statusfficial* *Locked* HBoot-3.19.0.0000 Radio-1.22.30306251.27G CidNum- HTC__Y13 Version Main - 3.33.401.6
So the things i`m clearly too dumb to understand is STEPS from A-Z ,to get Android Revolution HD over Original(full with crap )ROM !?!
Would appreciate if some smart developer could explain step by step what should i do first,and what last... should i get S-off first,or should i unlock it first,or make it bootable ...as i told, i read so many info ,and got rally confused about all that process :silly:
Sorry for my bad english ,and tnx in advance for all who cared to shine some knowledge in my darkness :angel:
GruziiC said:
Things i got to find out about my M8 = *software statusfficial* *Locked* HBoot-3.19.0.0000 Radio-1.22.30306251.27G CidNum- HTC__Y13 Version Main - 3.33.401.6
Click to expand...
Click to collapse
This forum section is specifically for the AT&T version of the M8, which your phone is not.
You want to post here: http://forum.xda-developers.com/htc-one-m8/help
But all you need to do to install ARHD on your phone is unlock the bootloader via HTCDev.com, install custom recovery and flash the ROM.
---------- Post added at 10:25 AM ---------- Previous post was at 10:23 AM ----------
xtiandrey said:
When i resturned to stock. I only flash the stock recovery at rom. And i dont the radio. What radio does? Do i still need to flash it?
Click to expand...
Click to collapse
Its not clear what you are trying to do, or what your current configuration is. The radio is the software that makes your phone work on the cell network.
If you did not specifically flash the radio (s-off required) its still on some stock radio. Although it might not correspond to the software (main version or OS) version you are on, since its also not clear what software you are on.
Ok really stupid question...what does AT&T mean ...this forum is FULL with different abbreviations ,i got no clue what does half of them mean ... there should be made a topic for noobs like me with only explanation of abbreviations:fingers-crossed:
GruziiC said:
Ok really stupid question...what does AT&T mean ...this forum is FULL with different abbreviations ,i got no clue what does half of them mean ... there should be made a topic for noobs like me with only explanation of abbreviations:fingers-crossed:
Click to expand...
Click to collapse
AT&T is a carrier in the US. If you didn't know what it meant, then you shouldn't have posted here.
If you don't know an abbreviation, than look it up. There are a variety of threads that already explain what you are asking about, or just Google for it. Here is one: http://forum.xda-developers.com/showthread.php?p=52484527
It doesn't tell you what AT&T is, but it explains a great many other common acronyms and terms.
AT&T is a mobile carrier...
---------- Post added at 04:17 PM ---------- Previous post was at 04:16 PM ----------
Not an android term...just a mobile carrier network
where would i find the firmware for 4.4.4.? I tried downloading the android revolution custom rom 22.1 but i couldnt get any wifi after flashing.
didnt realize i had to update firmware(however when i received phone i was on 4.4.2 and i tried doing software update and was told up to date)
i was told go back to stock and take stock update but i never received one in the first place.
is there a way that i can flash 4.4.4. firmware now that im bootloader unlocked/rooted and s-off?
would i flash zip firmware then reflash android 22.1 or the other way around?
sorry for the noob questions but after searching for awhile i can say im honestly stuck without having to go back to 100 percent stock and hope i get an ota update
there is no att 4.4.4,if on an ATT variant,change your cid to BS_US001 and flash the 3.28.1540.5 ruu if you really want 4.4.4
nogaros4v8 said:
where would i find the firmware for 4.4.4.? I tried downloading the android revolution custom rom 22.1 but i couldnt get any wifi after flashing.
didnt realize i had to update firmware(however when i received phone i was on 4.4.2 and i tried doing software update and was told up to date)
i was told go back to stock and take stock update but i never received one in the first place.
is there a way that i can flash 4.4.4. firmware now that im bootloader unlocked/rooted and s-off?
would i flash zip firmware then reflash android 22.1 or the other way around?
sorry for the noob questions but after searching for awhile i can say im honestly stuck without having to go back to 100 percent stock and hope i get an ota update
Click to expand...
Click to collapse
nogaros4v8 said:
where would i find the firmware for 4.4.4.? I tried downloading the android revolution custom rom 22.1 but i couldnt get any wifi after flashing.
didnt realize i had to update firmware(however when i received phone i was on 4.4.2 and i tried doing software update and was told up to date)
i was told go back to stock and take stock update but i never received one in the first place.
is there a way that i can flash 4.4.4. firmware now that im bootloader unlocked/rooted and s-off?
would i flash zip firmware then reflash android 22.1 or the other way around?
Click to expand...
Click to collapse
This is discussed in a great many places. Euro firmware and instructions here: http://forum.xda-developers.com/showthread.php?t=2696282
US Dev Edition firmware here (included with WNC's ROM): http://forum.xda-developers.com/att-htc-one-m8/development/att-4-4-3-2-22-1540-3-debloated-sense-6-t2837365
Assume you are on AT&T, since this forum section is specific to the AT&T version. Note that Euro ROMs may create some network issues on AT&T (most prominent of which is LTE issues with Google services). The best combo for AT&T is WNC's ROM and the matching firmware.
Wonders_Never_Cease said:
there is no att 4.4.4,if on an ATT variant,change your cid to BS_US001 and flash the 3.28.1540.5 ruu if you really want 4.4.4
Click to expand...
Click to collapse
i guess thats where the confusion lies. Its not that i want 4.4.4. i thought i needed 4.4.4. to run the custom rom.
---------- Post added at 04:07 PM ---------- Previous post was at 04:02 PM ----------
redpoint73 said:
This is discussed in a great many places. Euro firmware and instructions here: http://forum.xda-developers.com/showthread.php?t=2696282
US Dev Edition firmware here (included with WNC's ROM): http://forum.xda-developers.com/att-htc-one-m8/development/att-4-4-3-2-22-1540-3-debloated-sense-6-t2837365
Assume you are on AT&T, since this forum section is specific to the AT&T version. Note that Euro ROMs may create some network issues on AT&T (most prominent of which is LTE issues with Google services). The best combo for AT&T is WNC's ROM and the matching firmware.
Click to expand...
Click to collapse
correct i followed those instructions and downloaded the latest firmware from that link and i still couldnt get wifi to work on the revolution 22.1 rom. i then followed the directions went s-off to try and find a firmware for me to run the rom and couldnt get anything to work.
Yes i am on att. currently 4.4.2 rooted with s-off running twrp as my customer recovery.
nogaros4v8 said:
correct i followed those instructions and downloaded the latest firmware from that link and i still couldnt get wifi to work on the revolution 22.1 rom. i then followed the directions went s-off to try and find a firmware for me to run the rom and couldnt get anything to work.
Click to expand...
Click to collapse
What did you try to flash ("couldn't get anything to work" doesn't' tell us a thing)? And what was the result?
redpoint73 said:
What did you try to flash ("couldn't get anything to work" doesn't' tell us a thing)? And what was the result?
Click to expand...
Click to collapse
your right i should be more specific. i went under the firmware section for the revolution rom and downloaded the firmware (3.32.531.2.zip). Now learning that this is euro rom and not att specific rom i guess the firmware i installed had nothing to do with att. the result didnt change. it was as if i flashed the rom without the firmware again. everything worked fine just no wifi. Before doing any of that i did a backup with twrp with just stock settings. right now im rooted and s-off. Looking into the rom you suggested and reading before i do anything. Its quite confusing this go around for me not too sure why.
appreciate everyones help though ! :good:
Backup your files [email protected] pics music etc,change cid and run the 3.28.1540.5 ruu,this is the same device(att variant) as us developer edition,will put you to latest compatable firmware and enable you to run any 4.4.4 builds out.
nogaros4v8 said:
your right i should be more specific. i went under the firmware section for the revolution rom and downloaded the firmware (3.32.531.2.zip). Now learning that this is euro rom and not att specific rom i guess the firmware i installed had nothing to do with att. the result didnt change. it was as if i flashed the rom without the firmware again. everything worked fine just no wifi. Before doing any of that i did a backup with twrp with just stock settings. right now im rooted and s-off. Looking into the rom you suggested and reading before i do anything. Its quite confusing this go around for me not too sure why.
appreciate everyones help though ! :good:
Click to expand...
Click to collapse
nogaros4v8 said:
your right i should be more specific. i went under the firmware section for the revolution rom and downloaded the firmware (3.32.531.2.zip). Now learning that this is euro rom and not att specific rom i guess the firmware i installed had nothing to do with att. the result didnt change. it was as if i flashed the rom without the firmware again. everything worked fine just no wifi. Before doing any of that i did a backup with twrp with just stock settings. right now im rooted and s-off. Looking into the rom you suggested and reading before i do anything. Its quite confusing this go around for me not too sure why.
Click to expand...
Click to collapse
Did you flash the firmware with fastboot, following the instructions from the first link I supplied?
I think you are doing something wrong, which is probably why WNC is suggesting the RUU (which is a executable, and pretty much self-running).
Wonders_Never_Cease said:
Backup your files [email protected] pics music etc,change cid and run the 3.28.1540.5 ruu,this is the same device(att variant) as us developer edition,will put you to latest compatable firmware and enable you to run any 4.4.4 builds out.
Click to expand...
Click to collapse
just realized you wrote the rom that was suggested lol. I think im going to go that route instead. Not sure how to change a CID but i will def read up on it. i noticed your rom says it doesnt need to be changed however. thanks for the support
---------- Post added at 05:07 PM ---------- Previous post was at 04:59 PM ----------
redpoint73 said:
Did you flash the firmware with fastboot, following the instructions from the first link I supplied?
I think you are doing something wrong, which is probably why WNC is suggesting the RUU (which is a executable, and pretty much self-running).
Click to expand...
Click to collapse
yes i flashed the firmware with fastboot. i read both those posts before attempting even watched a few vids to make sure i did everything correct. However i think i am just going to go with WNC rom. i honestly had no idea there were euro roms and att specific roms. I figured everything in the att section was att specific. live and learn
nogaros4v8 said:
yes i flashed the firmware with fastboot. i read both those posts before attempting even watched a few vids to make sure i did everything correct. However i think i am just going to go with WNC rom. i honestly had no idea there were euro roms and att specific roms. I figured everything in the att section was att specific. live and learn
Click to expand...
Click to collapse
What is your current hboot and radio numbers (both are displayed in bootloader).
Also, you often have to flash the firmware zip twice in order for all the modules to install.
Connect phone to computer with fastboot in power settings turned off, open a command prompt navigate to your adb/fastboot location and run adb reboot bootloader,once phone reboots it will connect to fastbootusb ,once this is established run this command fastboot oem writecid BS_US001then run fastboot reboot-bootloader,once this is done can run the ruu from fastboot connection.
nogaros4v8 said:
just realized you wrote the rom that was suggested lol. I think im going to go that route instead. Not sure how to change a CID but i will def read up on it. i noticed your rom says it doesnt need to be changed however. thanks for the support
---------- Post added at 05:07 PM ---------- Previous post was at 04:59 PM ----------
yes i flashed the firmware with fastboot. i read both those posts before attempting even watched a few vids to make sure i did everything correct. However i think i am just going to go with WNC rom. i honestly had no idea there were euro roms and att specific roms. I figured everything in the att section was att specific. live and learn
Click to expand...
Click to collapse
redpoint73 said:
What is your current hboot and radio numbers (both are displayed in bootloader).
Also, you often have to flash the firmware zip twice in order for all the modules to install.
Click to expand...
Click to collapse
hboot- 3.19.0.000
radio 1.22.21331147a1.296
yea i read that it will fail sometimes the first time and to just run the process again.
nogaros4v8 said:
hboot- 3.19.0.000
radio 1.22.21331147a1.296
yea i read that it will fail sometimes the first time and to just run the process again.
Click to expand...
Click to collapse
The hboot and radio numbers indicate you are on the latest firmware. If you did in fact flash the firmware twice, I would be confidant the firmware is all properly installed. I would try either:
1) Flash the desired ROM again after wiping data, cache and Dalvik
2) RUU as WNC suggests
3) Try WNC's ROM with corresponding firmware

Need Help flashing 4.4.4 To AT&T HTC One M8.

I have an HTC One M8 AT&T Branded but it has 4.4.2 on it and i wanna flash viperrom 3.2.1 but it requires androids 4.4.4 software. im S-ON, 3.16 Bootloader with 1.58.502.1 Software number. Baseband Version is 1.16.21331931.LA11G_20.31A.4145.02L. im just looking to Update from 4.4.2 to 4.4.4 but i cant seem to find out how. Any help would be great.
Perfect.
Unlock your bootlooader if you haven't already, fastboot flash recovery (TWRP/PHILZ),root using the chosen custom recovery,make a backup before or after root.
Go here http://theroot.ninja/ for Sunshine
S-OFF cause that's what your going to need to update as far as 4.4.4
Orrrr just wait a few days for the ATT 4.4.4 build to be released (ETA 29th) and then youll have 4.4.4 without having to do anything.
Wonders_Never_Cease said:
Orrrr just wait a few days for the ATT 4.4.4 build to be released (ETA 29th) and then youll have 4.4.4 without having to do anything.
Click to expand...
Click to collapse
That's a better idea for sure.
I haven't noticed if Sunshine has an update that works with 4.4.4 yet.
Are you S-OFF ?
What are the advantages/disadvantages of S-OFF so the OP knows what he might be missing.
Do you know when the Sunshine update will be?
Yup,no [email protected],[email protected],there are plenty of posts about advantages and disadvantages...my point of view is simple,it is not needed for the novice,ive seen too many mess things due to lack of knowledge. My usage of it is for switching between att and developer ROM's to get latest updates. Outside of that I dont mess with conversions,to risky for a 6-700 device. My advice is stick to htc dev unlocked bootloader and wait for official update.
jball said:
That's a better idea for sure.
I haven't noticed if Sunshine has an update that works with 4.4.4 yet.
Are you S-OFF ?
What are the advantages/disadvantages of S-OFF so the OP knows what he might be missing.
Do you know when the Sunshine update will be?
Click to expand...
Click to collapse
Wonders_Never_Cease said:
Yup,no [email protected],[email protected],there are plenty of posts about advantages and disadvantages...my point of view is simple,it is not needed for the novice,ive seen too many mess things due to lack of knowledge. My usage of it is for switching between att and developer ROM's to get latest updates. Outside of that I dont mess with conversions,to risky for a 6-700 device. My advice is stick to htc dev unlocked bootloader and wait for official update.
Click to expand...
Click to collapse
Cool thank you
Im not S-OFF but hell ill wait for the 29th to roll around and see if i have an update. Can you link me to the info stating its around the 29th?
darkninja908 said:
Im not S-OFF but hell ill wait for the 29th to roll around and see if i have an update. Can you link me to the info stating its around the 29th?
Click to expand...
Click to collapse
I didn't Google for to long but I haven't found concrete links that state the exact date .how many times have we been promised a date and watch it pass by anyways.
May I ask if you've modified any other device before this one?
I'm not trying to push,but S-OFF might be in your future and will not halt an OTA from installing.
The version your on is easily exploitable using "Sunshine" unless you take the soon to be 4.4.4 update.
Nobody knows when Sunshine will have an update even with the team working on it as we speak.
Wont be much on Google @date,came from somewhere else. And nothing is ever "concrete" with software,especially with carrier branded software.
jball said:
I didn't Google for to long but I haven't found concrete links that state the exact date .how many times have we been promised a date and watch it pass by anyways.
May I ask if you've modified any other device before this one?
I'm not trying to push,but S-OFF might be in your future and will not halt an OTA from installing.
The version your on is easily exploitable using "Sunshine" unless you take the soon to be 4.4.4 update.
Nobody knows when Sunshine will have an update even with the team working on it as we speak.
Click to expand...
Click to collapse
jball said:
I didn't Google for to long but I haven't found concrete links that state the exact date .how many times have we been promised a date and watch it pass by anyways.
May I ask if you've modified any other device before this one?
I'm not trying to push,but S-OFF might be in your future and will not halt an OTA from installing.
The version your on is easily exploitable using "Sunshine" unless you take the soon to be 4.4.4 update.
Nobody knows when Sunshine will have an update even with the team working on it as we speak.
Click to expand...
Click to collapse
I have Rooted, and flashed multiple ROMS to my old M7 before. Nothing crazy.
I as well have the same build, unlocked bootloader, flashed custom recovery. Will I have to return to stock recovery using 1.58.502.1 RUU and to get the OTA update to 4.4.4??
I'm trying to get the latest Android Revolution ROM for 4.4.4 but realized I was in a bit of a pickle. I'd like to take the path of least resistance on this one - any advice would be super appreciated. Thanks!
pmoser16 said:
I as well have the same build, unlocked bootloader, flashed custom recovery. Will I have to return to stock recovery using 1.58.502.1 RUU and to get the OTA update to 4.4.4??
I'm trying to get the latest Android Revolution ROM for 4.4.4 but realized I was in a bit of a pickle. I'd like to take the path of least resistance on this one - any advice would be super appreciated. Thanks!
Click to expand...
Click to collapse
I'd say wait till tomorrow to see if an OTA update will roll out.
Or if you just can't wait for the ability to flash what you desire than I would go S-OFF and flash a non At&t firmware that you need to allow a smooth function of mentioned ROM.
Im restoring back to default AT&T ROM and such and will post weather the update has been pushed or not. i sure hope it has
**Update** Still no update, i got the " Current Software is up to date, You may check again in 23 Hours 59 Mintues.
darkninja908 said:
Im restoring back to default AT&T ROM and such and will post weather the update has been pushed or not. i sure hope it has
**Update** Still no update, i got the " Current Software is up to date, You may check again in 23 Hours 59 Mintues.
Click to expand...
Click to collapse
You can check as many times as you like by setting your time manually ahead and your phone/device won't know the difference.
Check as many times as you like but it will remain the same,you should get a notification when it's time
So if you don't have s-off you can't update to 4.44 Sense ROMS with AT&T? I'm on Slim Rom and sound quality stinks. I want the new Android Revolution but i've read wi-fi and such doesn't work. Clarification plz?
war eagle said:
So if you don't have s-off you can't update to 4.44 Sense ROMS with AT&T? I'm on Slim Rom and sound quality stinks. I want the new Android Revolution but i've read wi-fi and such doesn't work. Clarification plz?
Click to expand...
Click to collapse
Correct .
S-OFF allows you to change your CID witch will allow you to ruu Dev Edition 4.4.4 so everything runs smoothly
I've not looked on this thread in a while. I am S-off and unlocked and my cid is 11111111 but I have never updated firmware so that I can run a 4.4.4 rom. Is it correct that I flash a RUU (guess it's not called flashing when it comes to a RUU). How do I know which RUU to post - I found this one here: http://forum.xda-developers.com/showthread.php?t=2757462 (http://dl3.htc.com/application/RUU_...G_20.31A.4145.02L_release_368350_signed_2.exe)
Will I loose root or anything (other than wiping my data) when running the ruu.
jball said:
Correct .
S-OFF allows you to change your CID witch will allow you to ruu Dev Edition 4.4.4 so everything runs smoothly
Click to expand...
Click to collapse
karatche said:
I've not looked on this thread in a while. I am S-off and unlocked and my cid is 11111111 but I have never updated firmware so that I can run a 4.4.4 rom. Is it correct that I flash a RUU (guess it's not called flashing when it comes to a RUU). How do I know which RUU to post - I found this one here: http://forum.xda-developers.com/showthread.php?t=2757462 (http://dl3.htc.com/application/RUU_...G_20.31A.4145.02L_release_368350_signed_2.exe)
Will I loose root or anything (other than wiping my data) when running the ruu.
Click to expand...
Click to collapse
I'll just say that if it's a stock ruu than it's most likely without root and it will wipe as if it came out of the box.if its a full ruu than it will come with the updated firmware as well witch should allow you to flash 4.4.4 Roms and still run smoothly.
What I did around 5:00am this morning was restore my Dev edition backup I had along with the stock recovery so I could take the Dev edition lollipop official update and now I have lollipop firmware to use with my stock GPE 5.0.1 lollipop ROM/backup .
Sweetness
karatche said:
I've not looked on this thread in a while. I am S-off and unlocked and my cid is 11111111 but I have never updated firmware so that I can run a 4.4.4 rom. Is it correct that I flash a RUU (guess it's not called flashing when it comes to a RUU). How do I know which RUU to post - I found this one here: http://forum.xda-developers.com/showthread.php?t=2757462 (http://dl3.htc.com/application/RUU_...G_20.31A.4145.02L_release_368350_signed_2.exe)
Will I loose root or anything (other than wiping my data) when running the ruu.
Click to expand...
Click to collapse
Yes, running/flashing the 4.4.4 Dev Edition RUU will update you to that appropriate firmware. But, what you linked is not Dev Edition, its a stock AT&T RUU. And its not 4.4.4 either, its 4.4.2, which is probably where you already are.
What you want is the 3.28.1540 RUU linked here: http://forum.xda-developers.com/htc-one-m8/development/ruu-m8-developer-edition-sense-1-54-t2884777
RUU will wipe the phone, install stock ROM (meaning root will be lost) and stock recovery.
But I also think its overkill to run an RUU just to update firmware, if that is the intent. My suggestion is to just run the firmware linked in the following post (which also has great instructions for doing so): http://forum.xda-developers.com/att-htc-one-m8/development/att-4-4-3-2-22-1540-3-debloated-sense-6-t2837365
The above method shouldn't overwrite the current ROM and user data. But backup anything important before flashing firmware, just in case.
Side note, "flash" is a fairly generic term, and as the RUU flashes stock ROM among other things, the term "flash" is appropriate IMO.
So can I just load the firmware file and flash thru fastboot? Is it This one?
3.28.1540.5 Firmware only unmodified (Latest 4.4.4 Update,S-OFF REQUIRED)
http://goo.gl/tyhRRZ
redpoint73 said:
Yes, running/flashing the 4.4.4 Dev Edition RUU will update you to that appropriate firmware. But, what you linked is not Dev Edition, its a stock AT&T RUU. And its not 4.4.4 either, its 4.4.2, which is probably where you already are.
What you want is the 3.28.1540 RUU linked here: http://forum.xda-developers.com/htc-one-m8/development/ruu-m8-developer-edition-sense-1-54-t2884777
RUU will wipe the phone, install stock ROM (meaning root will be lost) and stock recovery.
But I also think its overkill to run an RUU just to update firmware, if that is the intent. My suggestion is to just run the firmware linked in the following post (which also has great instructions for doing so): http://forum.xda-developers.com/att-htc-one-m8/development/att-4-4-3-2-22-1540-3-debloated-sense-6-t2837365
The above method shouldn't overwrite the current ROM and user data. But backup anything important before flashing firmware, just in case.
Side note, "flash" is a fairly generic term, and as the RUU flashes stock ROM among other things, the term "flash" is appropriate IMO.
Click to expand...
Click to collapse

Categories

Resources