Related
Just wondering has anyone tried/thought about the feasibility of modding a Palm Pre touchstone charger for use in an atrix? would it be extremely difficult to do so?
thantos said:
Just wondering has anyone tried/thought about the feasibility of modding a Palm Pre touchstone charger for use in an atrix? would it be extremely difficult to do so?
Click to expand...
Click to collapse
As per post on engadget it's not so complicated
thantos said:
Just wondering has anyone tried/thought about the feasibility of modding a Palm Pre touchstone charger for use in an atrix? would it be extremely difficult to do so?
Click to expand...
Click to collapse
xboxexpert posted a tutorial for this on a nook color here . Looks easy enough and the same method should apply.
Hmmm.. interesting.. only wished someone would have tried previously to know if it'd fit inside the battery cover...
After looking at the iFixIt teardown for the Atrix I'm not thinking this would be a straight forward process.
http://www.ifixit.com/Teardown/Motorola-Atrix-4G-Teardown/4964/2
Boards aren't my strong point but it looks as though the +/- may be under the usb connector housing.
mtnecho said:
After looking at the iFixIt teardown for the Atrix I'm not thinking this would be a straight forward process.
http://www.ifixit.com/Teardown/Motorola-Atrix-4G-Teardown/4964/2
Boards aren't my strong point but it looks as though the +/- may be under the usb connector housing.
Click to expand...
Click to collapse
Need a better shot, but it looks like you can still hit the resistor between the two ground posts. Going to need some thin wire though.
I am curious to know if anyone will attempt this.
vmiku914 said:
I am curious to know if anyone will attempt this.
Click to expand...
Click to collapse
Don't think I'm going to sacrifice my Atrix to the hardware mod gods. Enjoying it too much and not terribly interested in dropping the money to replace it if it doesn't work out.
I don't know if I will be doing the mod, but these are some of the tips I would follow if i decided to. If I do it I'll post pictures..
1st:
Be sure to use the Palm Pixi's back cover with the smaller circuit board - this one.
Click to expand...
Click to collapse
2nd:
You might wanna consider buying this case since its thicker and you can dig a little bit if the circuit doesn't fit the standard battery door.
Click to expand...
Click to collapse
3rd:
In many phones the metal that keeps the memory card in place is the ground (-).
Click to expand...
Click to collapse
4th:
I'm sure there's an easy (+) pin you can solder to - so far i haven't found one, but many people cut a usb plug to fit inside the usb female socket and route the cables somehow (Watch the first video below). You have to remove the cut usb in order to use it with computer, also its quite ugly. The best, but very hard way is to solder the (+) wire directly to where the usb socket is soldered to the phone's circuit board .This I'll leave to a jewelry craftsman, I know, with lots of experience. MAKE SHURE YOU KNOW WHICH PIN IS THE POSITIVE!!! For polarity of the palm pixi's circuit boat refer to the first picture.
Click to expand...
Click to collapse
I know its a bit difficult, but... that's the way it is.
Useful links:
Galaxy S Mod.
First HD2 Mod.
Same mod but with extended battery (Not good looking)
You have probably seen this.
A lot of people forget to do this.
YOU ARE WELCOME!!!
I bought some of the pixi components and will try this out without the requirement of soldering.. I've been thinking.. is there any way to use the leads from the battery as the connection point as opposed to soldering directly to the port? Or is there a voltage regulator that I'd have to go through first...
First, you should try if it's really charging Atrix (batt's percentage going up), because it needs more current than standart phone.
But i'm thinking of modyfing my own, but with less invasive method
I wouldn't take apart my atrix again. I may have killed my first one getting my screen out. Those ribbon cables are a pain, and well, you might not need to remove the flex cables (the black flat ones), but if you do, you are most times pulling up the temp sensor too, and that thing never goes back!!
Just make sure you are good at what you do
Why not solder the the inductive piece to a chunk of mini usb cable first ? Completely non invasive and you'll be able to prove it works before you solder to the phone.
That was what I was considering. Unfortunate that the variances for the attrix are so tight.
mobileweasel said:
Why not solder the the inductive piece to a chunk of mini usb cable first ? Completely non invasive and you'll be able to prove it works before you solder to the phone.
Click to expand...
Click to collapse
If you're going to do that, you may as well just buy one that's already made.
I meant to do that as proof of concept. If it charger, take it apart and hide it under the battery cover.
Does anyone tried the Palm inductive charger with Atrix? Does it really work?
I just got mine in - will try it soon.
Let me ask you guys this...
1) Whats the point of all this?
Really? What is the point? The cool form factor? Bragging rights? It seems like
a big inconvenience for me, especially when you will need to take your charger somewhere.
Anyways, seems like a lot of work for just the convenience of not plugging in a mini usb cable.
Anyways, good luck and I hope you guys have fun
Perhaps you are right about it.
But whats the point in buying a lapdock or media dock when you can just get a laptop? What's the point in rooting or unlocking your phone? You could easily just leave it stock and most of the functions will work just fine.
Call it a hobby or challenge or a convenience or whatever. I made this thread merely asking for technical help. Not snide commentary that is counter productive.
Does anyone have any experience with removing a damaged charging port/flex cable? I made a thread about a week ago saying that mine was messed up and one of the wire strip on the charging slot was broken, but and didn't allow it to connect to my computer for file transfer. I talked to ATT and they said the store couldn't do anything and that I would need to call in. I don't want to take the risk of a huge charge, and found a single order part here www.etradesupply.com/oem-samsung-galaxy-note-sgh-i717-charging-port-flex-cable-ribbon.html
It is cheap, and I have e removed the back of my Note before, and removed most of this piece except for the ribbon, and which I have no idea how to. Are there any resources out there to help me with this? I don't want to mess up a new part trying to install this one.
(PS how do I start a new thread on the desktop site? I couldn't find anywhere to do it and SwiftKey isn't faster than using a real keyboard on my PC lol. I am obviously new)
Sent from my SAMSUNG-SGH-I717 using xda premium
Youtube is your friend. Watch the video and see the steps it takes. If you feel it's too much then try searching on your local Craigslist for a shop that may be able to fix it.
http://youtu.be/pD9R-YUT69Q
MrEous said:
Youtube is your friend. Watch the video and see the steps it takes. If you feel it's too much then try searching on your local Craigslist for a shop that may be able to fix it.
http://youtu.be/pD9R-YUT69Q
Click to expand...
Click to collapse
Thanks a lot! It totally slipped my mind to check out YouTube.
Sent from my SAMSUNG-SGH-I717 using xda premium
Bought 1 from ebay. Will try to do it myself when it's arrived.
Sent from my phablet ★★★Galaxy Note★★★
Good luck. I did it myself as well. It is not that difficult.
Sent from my MB860 using Tapatalk 2
Has anyone tried replacing just the digitizer on our phones? My friend's LCD is fine, it's just the glass that is cracked.
On my old HTC HD2 the digitizer was glued to the LCD, so swapping it out was pretty tough. I'm wondering if it's the same for this phone.
So it didn't charge also?
Sent from my SAMSUNG-SGH-I717 using XDA Premium HD app
Snarksneeze said:
Has anyone tried replacing just the digitizer on our phones? My friend's LCD is fine, it's just the glass that is cracked.
On my old HTC HD2 the digitizer was glued to the LCD, so swapping it out was pretty tough. I'm wondering if it's the same for this phone.
Click to expand...
Click to collapse
Yup, will be rough, it's glued.
Lcd and digitizer are fused on the note as well. Cheapest I seen it go for is like 250
Sent from my SAMSUNG-SGH-I717 using xda premium
gagejbond said:
Does anyone have any experience with removing a damaged charging port/flex cable? I made a thread about a week ago saying that mine was messed up and one of the wire strip on the charging slot was broken, but and didn't allow it to connect to my computer for file transfer. I talked to ATT and they said the store couldn't do anything and that I would need to call in. I don't want to take the risk of a huge charge, and found a single order part here <clipped URL because XDA won't let me quote it>
It is cheap, and I have e removed the back of my Note before, and removed most of this piece except for the ribbon, and which I have no idea how to. Are there any resources out there to help me with this? I don't want to mess up a new part trying to install this one.
(PS how do I start a new thread on the desktop site? I couldn't find anywhere to do it and SwiftKey isn't faster than using a real keyboard on my PC lol. I am obviously new)
Sent from my SAMSUNG-SGH-I717 using xda premium
Click to expand...
Click to collapse
Did you receive the part from that supplier? Was it the correct part? I ask because I need the same part for my Note. (Samsung told me that is not a part covered under warranty)
JeremyLC said:
Did you receive the part from that supplier? Was it the correct part? I ask because I need the same part for my Note. (Samsung told me that is not a part covered under warranty)
Click to expand...
Click to collapse
Just to follow up on my own post. I ordered the part, it arrived quickly, and it was DOA Waiting to hear from customer service now.
Be careful doing this I found the new part had the wrong antenna and my reception was gone afterward. Ended up replacing my phone because of that.
Sent from my SAMSUNG-SGH-I717 using xda app-developers app
I tried 3 charging ports from ebay,all from diffrent sellers and they were all DOA... Check out parts4repair, I ordered mine and 2 weeks later, my phone is fixed!
http://www.parts4repair.com/samsung-galaxy-note-i717-at-t-dock-charging-port/
I replaced mine, easy, just don't loose the screws, took about 5-10min
Sent from my SAMSUNG-SGH-I717 using xda app-developers app
endine said:
I tried 3 charging ports from ebay,all from diffrent sellers and they were all DOA... Check out parts4repair, I ordered mine and 2 weeks later, my phone is fixed!
http://www.parts4repair.com/samsung-galaxy-note-i717-at-t-dock-charging-port/
Click to expand...
Click to collapse
its took you that long to get the replacement port?
just replaced mine as well with the ebay one from ezletroniks(or something like that). $15 shipped, arrived in less than a week from California to Wisconsin.
Took around 10 minutes to replace. Charging up fine again which makes me very happy.
So it seems apparent that this is not a singular occurrence by any means, which is a little disheartening. But I just wanted to chime in and say that I'm currently on my 3rd charge port.
Fortunately, there's an awesome place a few miles away (I would trust the tech there with my life...he's fixed everything I've thrown at him thus far) that has been able to replace the part for me each time - but every damn time, it works perfect for about 2 weeks and then it goes back to the way it was before, which is always the same symptom: phone doesn't charge (or stay connected to the PC) unless I push the phone UP from back, and simultaneously push the end of the cable DOWN. And even then, sitting perfectly still, I get a sporadic connection.
Needless to say, the 2 extra OEM batteries/chargers (that you can charge just the battery with) and ADB over WiFi have become my best friends
So I'm wondering: (a) has anyone else had this problem multiple times like I have? And (B) has anyone else experienced the same thing as far as the "manual" method I have to use to keep it charging? I'm trying to, as much as possible, rule out the possibility that there's something else wrong with it
Replaced mine
Got the part, took about 15 minutes to replace. Hardest part was prying the bezel off the phone.
After replacing, putting it back together and making sure everything worked, I put the old port under a 30X loop to look at it.
on the board side, where the pins exit the plug, and go to the circuit boar, if you flex the port, I could see the pins LIFTING
off the pins on the board at the solder connection. If I had a micro solder iron & steady hand it would be a simple fix, but
since it took a 30X loop just to see it, and I don't have a micro iron, it was easier to spend less than 15 bucks, and 20 minutes
time to replace the thing :victory:
p51d007 said:
Got the part, took about 15 minutes to replace. Hardest part was prying the bezel off the phone.
After replacing, putting it back together and making sure everything worked, I put the old port under a 30X loop to look at it.
on the board side, where the pins exit the plug, and go to the circuit boar, if you flex the port, I could see the pins LIFTING
off the pins on the board at the solder connection. If I had a micro solder iron & steady hand it would be a simple fix, but
since it took a 30X loop just to see it, and I don't have a micro iron, it was easier to spend less than 15 bucks, and 20 minutes
time to replace the thing :victory:
Click to expand...
Click to collapse
That's actually exactly what the repair shop told me was wrong with it...although I couldn't recall exactly until you said this. I'm pretty sure he's just re-soldered if each time, and never actually replaced the board.
So to a non-hardware person...is that problem due to faulty manufacturing/poor quality parts on the Samsung end? Or does that just end up happening to all devices with a MicroUSB connection as they get used?
p51d007 said:
Got the part, took about 15 minutes to replace. Hardest part was prying the bezel off the phone.
After replacing, putting it back together and making sure everything worked, I put the old port under a 30X loop to look at it.
on the board side, where the pins exit the plug, and go to the circuit boar, if you flex the port, I could see the pins LIFTING
off the pins on the board at the solder connection. If I had a micro solder iron & steady hand it would be a simple fix, but
since it took a 30X loop just to see it, and I don't have a micro iron, it was easier to spend less than 15 bucks, and 20 minutes
time to replace the thing :victory:
Click to expand...
Click to collapse
I have a couple of guesses. One picture showed the connector was loose. It looks to me that the case tabs aren't soldered in. The other thing is I have one cable where the metal part sticks so far out that the plastic never touches the phone. It like sticking a screwdriver in the socket because you can wiggle the socket up and down. I now use a cable the plastic part touches the phone and doesn't wiggle the socket very easily. Wiggling any wire will eventually break it because of metal fatigue.
Sent from my SAMSUNG-SGH-I717 using xda app-developers app
I have a issue where when i plug my charger in it doesnt do anything.. but if I bend the charger down it works fine. Do i need to bend the pin in the phone up with tweezers?
I read around where If you have this issue with the charging port then its gone. But my phone still charges fine. I dont want to go poking and bending and break something and it doesnt charge at all.
Just a little advice.
I have the rogers galaxy note I727r
Try a different cable first. They wear out and loosen quicker than the port. Do not go poking and bending or you will be replacing the usb component on the phone for sure.
Agoattamer said:
Try a different cable first. They wear out and loosen quicker than the port. Do not go poking and bending or you will be replacing the usb component on the phone for sure.
Click to expand...
Click to collapse
i tried 5 different cables and one of which is the official samsung cable... no dice.
It sounds as if you need a charge port repair .....but
Before the device goes out .....try this ....
With a very small and flat object .....you can slightly bend the outer edge of the charge port on the side that does not contain the joining seam, or break in the port ...
The slight bend will tighten the cable tip, as it slides into the port, and create a better contact patch...
But be careful !!!......as you can damage the port if you get too aggressive ....
The bend occurs on the long flat side of the device port ...opposite the port seam ....g
P.S.....Proceed at your own risk ....but it worked perfect for me ...g
Just remember, your phone is under warranty. Might just be better to let them take care of it. But if you get brave here is the part:
http://www.ebay.com/itm/New-Chargin...998?pt=LH_DefaultDomain_0&hash=item19d4f7ccbe
Not that difficult to get to either. There are a few videos on youtube for disassembly instructions.
Agoattamer said:
Just remember, your phone is under warranty. Might just be better to let them take care of it. But if you get brave here is the part:
http://www.ebay.com/itm/New-Chargin...998?pt=LH_DefaultDomain_0&hash=item19d4f7ccbe
Not that difficult to get to either. There are a few videos on youtube for disassembly instructions.
Click to expand...
Click to collapse
i boughtit as a used phone.. is there a picture that you can show the outer edge?
If you contact Samsung instead of ATT your warranty should be honored still. But it would be cheaper to buy the board and fix it yourself then to pay for shipping to a samsung repair center unless you have one nearby. I have no better pictures of the usb port.
Nor do I .....
If you hold the phone while looking into the charge port ...( screen up )....
The part you slightly bend is the bottom of the charge port ...
Don't pry against the case ....just slightly bend the bottom portion up .....with a small tipped object ..
A dull knife tip works well .....g
Yeah.. two mornings ago, I woke up to a phone in it's dying throes of battery life.. having been on the charger all night.
It's been a little touchy with certain cords for the past month or so but now, it doesn't matter which of the many available charger cords I have, from brand new to the original - none of them make the phone thing to charge or connect it via USB to a computer.
It's dead Jim.
Before I begin, if there is already a thread outlining this particular problem, I apologize in advance.
Yesterday my Truesmart was in the charging cradle sitting on my desk, not realizing it, I accidentally opened a draw which pulled on the USB cable, dragging my Truesmart off of the desk and onto the floor. My truesmart fell about 2 feet and is fine, but the charging cradle will no longer charge it. I would assume that something broke in the cradle when it fell, which justifies the pathetic quality of it, although there is no visual damage on the cradle and when shaken nothing rattles around inside of the cradle.
My question is what should I do now? I am almost certain that it is the cradle that is the problem and not the Truesmart or the USB as the watch will still turn on and the USB will charge other devices. I have tried different power sources and different USBs and I only have one cradle. Is there anything I should troubleshoot in order to try and get the cradle working? Or is is possible that the problem is with the watch?
Any assistance would be greatly appreciated.
The spring contacts in the cradle may have gotten smushed in a bit by the impact. Try prying them up gently with like a needle.
Otherwise, the solders connecting the microUSB connector inside the cradle might have failed. They have been reported to be of poor quality on another owner's cradle with cold solders. Try resoldering them if probing them shows them not good connections anymore.
Thirdly, maybe your USB cable itself was damaged in the drop. Test it too.
Sent from my Nexus 5 using Tapatalk
I tried what you suggested with the needle and it didn't make any difference, they seem to be at the right position anyway.
I have a feeling it might be the solders, as it is possible that the sudden shock of the microUSB inside of the port caused something to break. Unfortunately I do not have any knowledge of soldering nor the equipment to do it. I wouldn't know how to open up the cradle without breaking it anyway.
I already tested the USB cable, it charges anything else, and I have tried other USBs with the Truesmart to make sure that it is infact the cradle.
I have sent Magan (may or may not have spelt her name right) two emails and have received no response.
Asking omate for another cradle is useless. Omate is focusing on shipping units not cradles. I know this because my cradle stopped working also. The solder on the female USB plug had failed. I took it into a local electronic repair shop and they resoldered a new plug on. They also asked me what doll or store I pitched the charger at.
I've been thinking of replacing the spring contacts with actual pogo pins. It's silly that the charger doesn't utilize them to begin with.
Sent from my GT-N5110 using Tapatalk
rhineymac said:
Asking omate for another cradle is useless. Omate is focusing on shipping units not cradles. I know this because my cradle stopped working also. The solder on the female USB plug had failed. I took it into a local electronic repair shop and they resoldered a new plug on. They also asked me what doll or store I pitched the charger at.
Click to expand...
Click to collapse
I am aware but I figured it was worth a shot since my order was missing a keychain that I was told would ship "soon".
I might look into taking it into a shop, how much did it cost you to do that? And I didn't understand your last sentence.
He mistyped "dollar store".
Apparently they have such cheap budget shops up in Canada too. I get my colored USB cables from them, they say, " Made in China" on them and generally last a couple of weeks.
Sent from my Nexus 5 using Tapatalk
Have you had the back of the watch off? If so loosen all 4 screws then tighten the 2 where the charge pins are first - then tighten the other end, where the buttons and camera is, last. I had an issue where the watch would not charge after reinstalling the back. I think the internal contact pins barley contact the flexible plastic copper pads. I originally crisscrossed tightened the screws and it wouldn't charge. If I have to install the back cover again I will most likely add a thin layer of something underneath the cable pad to help close the gap and provide a more solid contact for the internal pins. I could visibly see where there was maybe 2 out of the 4 pins making adequate contact.
Oops yes I ment dollar store. It didn't cost me much. $10 but the guy told me that it wouldn't last long, which it didn't, it stopped charging my ts today. He told me that its cheap, pure and simple. I was suppose to receive a spare that I paid for. When I asked about it I was told they won't ship it until after all KS and preorders were shipped. Omates way of telling me that I'm SOL
rhineymac said:
Oops yes I ment dollar store. It didn't cost me much. $10 but the guy told me that it wouldn't last long, which it didn't, it stopped charging my ts today. He told me that its cheap, pure and simple. I was suppose to receive a spare that I paid for. When I asked about it I was told they won't ship it until after all KS and preorders were shipped. Omates way of telling me that I'm SOL
Click to expand...
Click to collapse
I realized you meant dollar store shortly after posting lol, unfortunately I have even seen nicer chargers at the dollar store. $10 isn't bad but I guess at that price it makes sense to get a new charger if possible. I love how I am fortunate to have a semi-working watch but can't even use it because I don't have a working charger. Thanks for all of your help Omate -.-
SkyHawkTech said:
Have you had the back of the watch off? If so loosen all 4 screws then tighten the 2 where the charge pins are first - then tighten the other end, where the buttons and camera is, last. I had an issue where the watch would not charge after reinstalling the back. I think the internal contact pins barley contact the flexible plastic copper pads. I originally crisscrossed tightened the screws and it wouldn't charge. If I have to install the back cover again I will most likely add a thin layer of something underneath the cable pad to help close the gap and provide a more solid contact for the internal pins. I could visibly see where there was maybe 2 out of the 4 pins making adequate contact.
Click to expand...
Click to collapse
I had the back off of the watch once, after putting it back on it worked fine up until I dropped it. The watch will turn on, it just won't charge. I will try your suggestion anyway when I have my watch around though. The assembly of the watch is disgustingly poor, there is what looks like dried glue seeping out of the SIM slot of my watch. Very lucky to have no issues with buttons or pin contact and etc.
Agent. said:
I realized you meant dollar store shortly after posting lol, unfortunately I have even seen nicer chargers at the dollar store. $10 isn't bad but I guess at that price it makes sense to get a new charger if possible. I love how I am fortunate to have a semi-working watch but can't even use it because I don't have a working charger. Thanks for all of your help Omate -.-
I had the back off of the watch once, after putting it back on it worked fine up until I dropped it. The watch will turn on, it just won't charge. I will try your suggestion anyway when I have my watch around though. The assembly of the watch is disgustingly poor, there is what looks like dried glue seeping out of the SIM slot of my watch. Very lucky to have no issues with buttons or pin contact and etc.
Click to expand...
Click to collapse
the problem ive had with the charger is the female usb port. its very loose. i wonder if we will ever see the xtra things we paid for, xtra chargers, tshirts sd cards. its bad enough that the watch is a mess, but to have a propriatiery charger is just icing on the cake. theres not way of fixing it. well there is,but it only lasted a week. the guy who fixed mine laughed at me and told me you get what u pay for. This is only partly true, the charger was $5 but isnt worth $1
You could make a charger with a dollar store USB charging cable you cut up to expose the +5 and gnd wires, then tape them to the right pins on the back of the watch, carefully.
Sent from my Nexus 7 using Tapatalk
rhineymac said:
the problem ive had with the charger is the female usb port. its very loose. i wonder if we will ever see the xtra things we paid for, xtra chargers, tshirts sd cards. its bad enough that the watch is a mess, but to have a propriatiery charger is just icing on the cake. theres not way of fixing it. well there is,but it only lasted a week. the guy who fixed mine laughed at me and told me you get what u pay for. This is only partly true, the charger was $5 but isnt worth $1
Click to expand...
Click to collapse
I'm pretty sure mine is the female USB port too, as my watch was plugged in when it fell so I assume the shock of the male USB caused it to break. Your guess is as good as mine as to if they ever plan on actually fulfilling their promises, they have done a pretty crummy job thus far. The charger is absolute junk, at least if we had the charging cable they initially promised we might be able to work with it a bit more.
trent999 said:
You could make a charger with a dollar store USB charging cable you cut up to expose the +5 and gnd wires, then tape them to the right pins on the back of the watch, carefully.
Sent from my Nexus 7 using Tapatalk
Click to expand...
Click to collapse
That isn't a bad idea for a temporary fix but the fact that it even comes down to doing something like that is absurd in my opinion, the charger should have been done and ready while they were dealing with all of the other BS issues.
Well, remember that for most owners the charging cradle they received works fine. It is not that poorly designed - mostly failures reported have been due to shoddy assembly. Similarly careless assembly has been reported on the watch itself in various areas.
I got my extra charger I ordered via Kickstarter, included in the package, but have never tested it nor needed to. I also figured out a way to charge the spare battery with an Anker universal charger, just in case. That charger came free with a couple of VGNexus batteries I bought from Amazon.
You might have better luck with the USB port repair staying fixed if you support its attachment to the board, such as it is, with an application of SuperGlue prior to resoldering the connections.
Holding a cable connector in place via only the contact solders would always be a bad design though.
Sent from my Nexus 7 using Tapatalk
I've ordered the Z2 and it should be coming to my door any day now. When I realized that a magnetic charger might be a good idea to prevent wear of the microUSB port I started to look at the options available. Unfortunately the charging dock sold by Sony is too expensive in my opinion and I would like to find an off-brand alternative. I've looked through the posts on this forum and have come to understand that putting the charger in the wrong direction could be a big mistake. I'm still willing to buy just a cable but would prefer a dock to help prevent this.
My questions is does anyone have a suggestion for a dock(preferable) / cable?
I found this cable on amazon:
http://www.amazon.ca/gp/product/B00...pf_rd_t=101&pf_rd_p=1947489602&pf_rd_i=915398
PS: A lot of docks on amazon have some bad reviews and I'm wary of buying them
I was in the same boat. The Sony dock looks nice like but it was fairly expensive.
I just ordered this last week:
http://www.amazon.ca/Magnector-Perf..._1_2?s=wireless&ie=UTF8&qid=1421124799&sr=1-2
I've got genuine Sony and this one as well. Sony charger is cut more precisely, phone is held exactly as it should with no wiggle etc. But this alone doesn't justify 10 times higher price. The cheapo one does the job in the same way, I see no difference in charging speed. For example this cable is OK as well. If you don't mind waiting for delivery (it takes about 4 weeks to Europe), I can only recommend these products and Aliexpress site.
Regarding the cables with LED indicator - I've got one and even if it's interesting I don't find it useful. LED light is always on and when it reaches ~95% battery threshold it starts to flicker until fully charged, then the color changes to solid again.
Is it hard to screw up the direction of the charger? I've heard it will completely discharge the battery (It shorts the terminals?)
Also, is there a thin case that has a slot for the magnetic charging / what cases do you use if any?
Thanks for the info guys!
Theoretically the plastic around the terminals should prevent the connector from actually connecting "the wrong way" but in practice it can still happen, especially if you insist in moving and pushing the cable.
If the cable is coming out from "the middle" of the connector is easier to put it wrong (otherwise is easy to remember the cable has to go from the middle of the phone to the bottom so is much harder to make the mistake). However because the phone is so symetric you might confuse the front with the back and put it in reverse even in the docking station.
And last but not least make sure you have good warranty - it is possible that the magnet will "suck out" the connector from the phone, mine is barely hanging and is supposed to be from the batch that fixed this issue.
I have the original Sony dock as well as a third party dock. I also have a magnetic adapter for micro USB. All are working fine. Here are the links:
Third party dock - this works fine with my Z2 even though the title says Z3.
Micro USB adapter
Thanks for the reply unni_kmr, unfortunately I'm in Canada and I can't order through amazon.com easily. (Also that isn't on amazon.ca)
Anyone have input on whether I should get this dock for $15?
http://www.amazon.ca/Patec®-Magneti...=UTF8&qid=1421438530&sr=1-15&keywords=z2+case
Also, I'm looking for a case that's slim but doesn't impede the magnetic charging port. Any suggestions?
EDIT: Found this case, might try to cut a charging hole myself
http://www.amazon.ca/Xcessor-Vapour...id=1421440356&sr=8-2&keywords=z2+case+xcessor
WGuitar said:
Also, I'm looking for a case that's slim but doesn't impede the magnetic charging port. Any suggestions?
Click to expand...
Click to collapse
I don't have a case. I am using the Mocolo tempered glass on front and back. I bought it from here. Its very thin glass. Even with it on the front and back, the phone slides into the docks easily.
slow charging speed
hi there, i recently updated my Z2 , to 4.4.4 and everything is absolutely as expected but magnetic charging speed has taken a serious blow. with 4.4.2 it was as fast as normal cable charging but now with 4.4.4 it has become extremely slow , almost takes 8 minutes to charge 1%, and more than 8-9 hrs to fully charge ..
anyone else facing a similar issue .....kindly suggest solutions.:crying:
thanks
WGuitar said:
I've ordered the Z2 and it should be coming to my door any day now. When I realized that a magnetic charger might be a good idea to prevent wear of the microUSB port I started to look at the options available. Unfortunately the charging dock sold by Sony is too expensive in my opinion and I would like to find an off-brand alternative. I've looked through the posts on this forum and have come to understand that putting the charger in the wrong direction could be a big mistake. I'm still willing to buy just a cable but would prefer a dock to help prevent this.
My questions is does anyone have a suggestion for a dock(preferable) / cable?
I found this cable on amazon:
http://www.amazon.ca/gp/product/B00...pf_rd_t=101&pf_rd_p=1947489602&pf_rd_i=915398
PS: A lot of docks on amazon have some bad reviews and I'm wary of buying them
Click to expand...
Click to collapse
What do you mean by putting the charger in the wrong direction could be bad. Do you mean the magnetic charger can only work in one specific direction?
y300owner said:
What do you mean by putting the charger in the wrong direction could be bad. Do you mean the magnetic charger can only work in one specific direction?
Click to expand...
Click to collapse
Not only it can work in only one direction but even worse if you manage to make it connect in reverse it might break the phone or the battery. Yay Sony!
d210 said:
Not only it can work in only one direction but even worse if you manage to make it connect in reverse it might break the phone or the battery. Yay Sony!
Click to expand...
Click to collapse
I use a "magnetron" cable for several moths now and never had any issues with it.
It is not possible to connect it in the wrong orientation.
I'm really happy with it and would absolutely buy it again.
kuhno said:
I use a "magnetron" cable for several moths now and never had any issues with it.
It is not possible to connect it in the wrong orientation.
I'm really happy with it and would absolutely buy it again.
Click to expand...
Click to collapse
Very expensive cable though...
And if you wiggle it a bit I'm sure you can make contact with it even in reverse. I assume it is using like any other cable the normal "mechanical protection" which consists in a tiny (fraction of a mm) extra plastic on the "lower" pin from magnetic connector.