This tread is referring to a S7-721u version in Malaysia with Gr8 bundled pre-installed.
Unfortunately, I lost my Gr8 activation code and unable to login to the device anymore after a factory reset. After some research, I have managed to flash it with the original firmware. Yes, I lost me Gr8 code, so I don't have the access to the daily subscription anymore, but I got my Huawei Mediapad back without unwanted pre-installed apps.
I am sharing this guideline so that it would be easier for people who faced the same issue like me. For people already got your Huawei Mediapad, keep your Gr8 code safe and remember where you keep it.
Prepare an microSD card with any storage size larger than 1GB.
Format microSD card.
Download Huawei official release firmware (S7-721u, Android4.3, C232B008, General).
Unzip downloaded firmware.
Delete file “au_temp.cfg” in dload folder.
Copy dload folder with UPDATA.APP in it.
Paste dload folder in your microSD card.
Power Off Huawei Mediapad. Insert microSD card.
Press Power + volume up + volume down keys together. The phone automatically enters the upgrade mode, and then begin the upgrade. Release the keys.
Once the progress bar reaches 100%, the phone will automatically restart. DONE!
What is new version C232B008 or C264B001? My tablet is on C264B001.
mugy said:
What is new version C232B008 or C264B001? My tablet is on C264B001.
Click to expand...
Click to collapse
No idea. Sorry.
Deleting the au_temp.cfg.
sunnysardine said:
This tread is referring to a S7-721u version in Malaysia with Gr8 bundled pre-installed.
Unfortunately, I lost my Gr8 activation code and unable to login to the device anymore after a factory reset. After some research, I have managed to flash it with the original firmware. Yes, I lost me Gr8 code, so I don't have the access to the daily subscription anymore, but I got my Huawei Mediapad back without unwanted pre-installed apps.
I am sharing this guideline so that it would be easier for people who faced the same issue like me. For people already got your Huawei Mediapad, keep your Gr8 code safe and remember where you keep it.
Prepare an microSD card with any storage size larger than 1GB.
Format microSD card.
Download Huawei official release firmware (S7-721u, Android4.3, C232B008, General).
Unzip downloaded firmware.
Delete file “au_temp.cfg” in dload folder.
Copy dload folder with UPDATA.APP in it.
Paste dload folder in your microSD card.
Power Off Huawei Mediapad. Insert microSD card.
Press Power + volume up + volume down keys together. The phone automatically enters the upgrade mode, and then begin the upgrade. Release the keys.
Once the progress bar reaches 100%, the phone will automatically restart. DONE!
Click to expand...
Click to collapse
How important is it to delete that file. Is that the reason why when i install the update it says "update.app is a invalid package"? Thanks mate.
Hi. I just reinstall the software, but how do I get back my e papers subscriptions?
Is there any costum rom, and i have this tablet locked on one network ,is there a solution to run other network.thanks in advance.
I did all as you said, but now my tablet is completely dead.
Thanks it worked.
Provide the download link for the firmware please?
Thx Sunnysardine, it works for me.
Just to add a bit for my experience.
The process 1 - 8 MUST be followed exactly. I tried putting the update.app w/o the load folder, it did not work
For process 10, it takes a bit of time. the Huawei logo showed up for quite long before it power up to 1st screen. after that, all well. So got to be patient a little bit
Thanks man
I followed ur instructions exactly and it works, nice
If not for this, I would have thrown away my mediapad, it totally not login-able/ unusable without Gr8 code
Thanks again!
it is work for me.. thanks for sharing
Hi there, I found a way to remove GR8 app without installing the update. I found out that due to the device cannot detect the update in my sd card.
1) turn on the Huawei media pad s7-721u, unlock the screen
2) plug in to computer/laptop windows 7,8 or windows 10
3) on the Huawei media pad screen, it will pop up usb setting, select hiSuite usb type option
4) at the andoid setting, please go to about table setting, then enable developer mode by taping 7 times at Build number
5) still at android setting, go to security, make sure your android Screen lock setting is set under Huawei unlock,the go to shortcut setting, need to set to google app and android setting app.
6) install HiSuite to your computer - this is the Huawei official computer device managed software tool
7) install iRoot software to your computer. careful with this installation, it full of bloatware, but don't worry it don't have a virus.
8) run the iRoot and it will root your device. It will restart your Huawei pad multiple times.
9) after it root complete, unlock your device then go to google play ( as your android unlock setting option have the google play as describe in step 5)
10) install System app remover from google play
11) open the app, go to inside the app setting, remove setting Hide core system app
12) go to the main menu of the app remover, under manager, select system app, now you can find gr8 gallery app. Removed that app then restart the device.
13) you will have multiple error in android, just reboot and the error gone. DONE
This is where you can download the firmware
[email protected]@/download/downloadCenter?downloadId=27805&version=51115&siteCode=pk
Wrong Firmware
sunnysardine said:
This tread is referring to a S7-721u version in Malaysia with Gr8 bundled pre-installed.
Unfortunately, I lost my Gr8 activation code and unable to login to the device anymore after a factory reset. After some research, I have managed to flash it with the original firmware. Yes, I lost me Gr8 code, so I don't have the access to the daily subscription anymore, but I got my Huawei Mediapad back without unwanted pre-installed apps.
I am sharing this guideline so that it would be easier for people who faced the same issue like me. For people already got your Huawei Mediapad, keep your Gr8 code safe and remember where you keep it.
Prepare an microSD card with any storage size larger than 1GB.
Format microSD card.
Download Huawei official release firmware (S7-721u, Android4.3, C232B008, General).
Unzip downloaded firmware.
Delete file “au_temp.cfg” in dload folder.
Copy dload folder with UPDATA.APP in it.
Paste dload folder in your microSD card.
Power Off Huawei Mediapad. Insert microSD card.
Press Power + volume up + volume down keys together. The phone automatically enters the upgrade mode, and then begin the upgrade. Release the keys.
Once the progress bar reaches 100%, the phone will automatically restart. DONE!
Click to expand...
Click to collapse
How can I fix the tablet after being flashed with wrong firmware?
It doesn't turn on and in QPST or QFIL it was in download mode.
I have correct firmware and its dump.
Related
Hi,
Has anyone managed to download the firmware update from Huawei's website here? I've been unable to download it for weeks now. The link seems to be down. Any mirrors?
Are you serious?
Try the search feature?
I managed to download it after trying several times. However, I keep getting a FAIL when I follow the instructions, i.e. copy the dload directory to the root of my sdcard, insert it, press and hold volume down + power button.
And from the FAIL screen, I can only reboot back into the update screen, which fails again.
1. What have I done wrong?
2. Since the battery is fixed, how can I force shutdown?
Usually that happens if the download is corrupted. Try to redownload the fw again. Btw, have you tried to remove the SD card? If the SD card with dload folder (with relevant files inside) is inserted then it would always go to the update screen.
to force shutdown hold power button for 10 seconds
Thanks. Turns out there's something wrong with my sdcard. I don't know why - they're working perfectly fine in Windows or in other phones. Anyway, I tried a 3rd card and it worked.
make sure that your card is formatted to FAT32
I am looking for a firmware for my Huawei G-610 (V100R001C00B115). I couldn't find it free of cost over the internet, can anyone help me finding it?
HamzaLV said:
I am looking for a firmware for my Huawei G-610 (V100R001C00B115). I couldn't find it free of cost over the internet, can anyone help me finding it?
Click to expand...
Click to collapse
check it here bro http://consumer.huawei.com/np/support/downloads/index.htm
STEPS FOR INSTALLATION
step One: copy a large package path UPDATA.APP to the SD card dload UPDATA.APP.
Step Two: Check the root directory of the SD card you dload UPDATA.APP.
Step Three: phone turned off, insert the SD card, while pressing the volume up button + volume down key switch button, the phone automatically enters the upgrade mode, and then begin the upgrade in Figure
Step Four: After the progress bar to go full fixed, the phone will automatically restart If you do not manually remove the battery.
sorry for late reply btw good luck!!!
Hello all,
I have bought Media pad x1 501-u, unfortunately I updated it to Kitkat from there website, then my mobile turned into chinese and no google firmwork so I cant even sync my gmail contacts using gmail, I cant update my programs using playstore. and what is worse is that there is no arabic!! its my native language and I need help! PS: my mobile is not rooted.
what is the best solution??
501U is natively a chinese device = was never meant to be sold outside China.
Standard procedure with Huawei:
Download the ROM (Either from Huawei or EMUI), unzip and copy the dload folder onto the root directory of an SD Card of at least 2GB formatted in FAT32.
Power off the X1, insert card, power on also holding volume up (if not successful hold volume up&down). You know you did it right when mister droid shows up.
Screen may blank for long periods!!
When it reboots after showing update success, remove the SD card, or it will do it again.
To get google back you will have to download several apps from the Huawei store which is available on tge homescreen. Please refer to the thread "not synching Google contacts".
mru55 said:
501U is natively a chinese device = was never meant to be sold outside China.
Standard procedure with Huawei:
Download the ROM (Either from Huawei or EMUI), unzip and copy the dload folder onto the root directory of an SD Card of at least 2GB formatted in FAT32.
Power off the X1, insert card, power on also holding volume up (if not successful hold volume up&down). You know you did it right when mister droid shows up.
Screen may blank for long periods!!
When it reboots after showing update success, remove the SD card, or it will do it again.
To get google back you will have to download several apps from the Huawei store which is available on tge homescreen. Please refer to the thread "not synching Google contacts".
Click to expand...
Click to collapse
Which ROM?? I have already download kitkat rom from their website and this what caused the problem. when i bought this device it was jelly bean and has google framework and no chinese .. and the arabic language was working.
after the kitkat update, I encountered all those problems.
[7D-501u]KitKat 4.4.2 / EMUI 3.0 / 400 DPI
http://forum.xda-developers.com/hua...-kitkat-4-4-2-emui-3-0-400-dpi-t2925015/page2
Work
eennap said:
[7D-501u]KitKat 4.4.2 / EMUI 3.0 / 400 DPI
http://forum.xda-developers.com/hua...-kitkat-4-4-2-emui-3-0-400-dpi-t2925015/page2
Work
Click to expand...
Click to collapse
I downloaded this file to my SD card. its only one file named "update" and my tablet is not recognizing it. I mean when i restart or make local update my tablet doesnt show anything. something wrong? did I miss any step?
Elnoumeno said:
I downloaded this file to my SD card. its only one file named "update" and my tablet is not recognizing it. I mean when i restart or make local update my tablet doesnt show anything. something wrong? did I miss any step?
Click to expand...
Click to collapse
Hi,
Apart from the update.app file, you also have to download the attached file (only 9xx bytes) in the below post:
http://forum.xda-developers.com/showpost.php?p=56436713&postcount=6
extract it to your root microsd card, then put the "update.app" file in the dload folder; reboot your x1 or make local update (have to manually choose the file from external sd card). After successfully upgrading, don't forget to remove your microsd card and plug to your PC to delete the update files.
Once you successfully upgrade it to this kitkat, you will not have any goggle app/framework. You have to go to Huawei App Center. search for and download Google Play and Google Play service. Then, in the same Huawei App Center, search by typing "google", you will see a large google banner on the top of the search result, tap it and you'll see a lot of google stuff. At least you have to download google sync (look at calendar icon) and another google sync (look at contact icon). Once downloaded, you will be able to sync your google contact and calendar back. You can then download other google apps from Google Playstore.
bthoven said:
Hi,
Apart from the update.app file, you also have to download the attached file (only 9xx bytes) in the below post:
http://forum.xda-developers.com/showpost.php?p=56436713&postcount=6
extract it to your root microsd card, then put the "update.app" file in the dload folder; reboot your x1 or make local update (have to manually choose the file from external sd card). After successfully upgrading, don't forget to remove your microsd card and plug to your PC to delete the update files.
Once you successfully upgrade it to this kitkat, you will not have any goggle app/framework. You have to go to Huawei App Center. search for and download Google Play and Google Play service. Then, in the same Huawei App Center, search by typing "google", you will see a large google banner on the top of the search result, tap it and you'll see a lot of google stuff. At least you have to download google sync (look at calendar icon) and another google sync (look at contact icon). Once downloaded, you will be able to sync your google contact and calendar back. You can then download other google apps from Google Playstore.
Click to expand...
Click to collapse
Its working but its chinese, how can i choose another language. I am lost
when you first reboot after upgrade, the first screen with Chinese, you can actually scroll the middle part of the screen, it should have English option.
Hello XDA members.
This is my first post so any advice about posting is very welcomed. And now the problem.
I have a Huawei S8-701U tablet that is stuck at “Recovery image verify failed” error. The major problem I have is that it cannot be recognized by my windows 7 based computer in order to try all the helpful advice I found inside XDA forum. So I would be grateful if you could help me connect the tablet with pc and try your advice to resolve mu issue.
[email protected] said:
Hello XDA members.
This is my first post so any advice about posting is very welcomed. And now the problem.
I have a Huawei S8-701U tablet that is stuck at “Recovery image verify failed” error. The major problem I have is that it cannot be recognized by my windows 7 based computer in order to try all the helpful advice I found inside XDA forum. So I would be grateful if you could help me connect the tablet with pc and try your advice to resolve mu issue.
Click to expand...
Click to collapse
Hi if your device model is t1 8.0 (S8701u)download this firmware:
Huawei MediaPad T1 8.0 (S8701u)
http://download-c1.huawei.com/download/downloadCenter?downloadId=73603&version=270428&siteCode=gh
If your device model is M1 8.0 (S8701u) download this one
Huawei MediaPad M1 8.0 (S8701u)
http://huawei-firmware.com/rom/huawei-mediapad-m1-80/s8701u/1551
Follow instruction good luck
Hello again.
I copied the dloader folder as instruction sais at SD card but i cannot go into update mode with the instructions provided. I followed the" 1.2.2 SD card manually upgrade"
1.2.2 SD card manually upgrade
1) dload folder will be copied to the SD card root directory.
2) Make sure the board is turned off, insert the SD card into the card.
3) Press the volume keys cut (away from the power button key) and hold, then press the power button board to boot.
4) Continue to press and hold the volume down until the machine into the SD card upgrade interface.
5) normal upgrade, the upgrade is successful, the upgrade fails phenomenon and the same SD card automatically upgraded.
Any other sugestion please?
[email protected] said:
Hello again.
I copied the dloader folder as instruction sais at SD card but i cannot go into update mode with the instructions provided. I followed the" 1.2.2 SD card manually upgrade"
Any other sugestion please?
Click to expand...
Click to collapse
Try this , Hold just vol down and plug USB cable : ). This is for fastboot mode , so if you are able to get your device recognised extract update.app with huawei extractor tool .
Example:
https://www.youtube.com/watch?v=OKRTbv-6Kzc
Today when I saw at XDA app that I have a replay I said “ Thank God my problem is over” but nop!! A new problem appeared. I download the extractor tool but when I open the update.app file I saw that there where not all the files needed as I saw at the video example. So two possibilities exist. Neither the files are not indeed inside the .app file or my myopia has gone up and I can’t see.
Any help please??
P.S I tried to upload a screenshot from extraction tool but with now luck.
[email protected] said:
Today when I saw at XDA app that I have a replay I said “ Thank God my problem is over” but nop!! A new problem appeared. I download the extractor tool but when I open the update.app file I saw that there where not all the files needed as I saw at the video example. So two possibilities exist. Neither the files are not indeed inside the .app file or my myopia has gone up and I can’t see.
Any help please??
P.S I tried to upload a screenshot from extraction tool but with now luck.
Click to expand...
Click to collapse
Can you post on the internet like on the https://imgur.com/upload and send me link to private message .
Hello!
I tried with the files you suggested but I can not go into fast boot mode or any mode so I’m starting to believe that there is no way fix it. The only think it does when I try all button combinations is to restart nothing more. I appreciate all the help but maybe there is no way to get into it.
Great news!!!
I finally managed to install the new firmware. :laugh: After doing again and again what I've been advised
All i did was to press Vol+ and Vol - while pressing power button and voila! ! The little green robot appeared and start to install the programme. I forgot to say that i put the 'dload' folder into SD card.
Thanks for all the help!!:good::good:
I have a T9 4GB/64GB TV BOX (RK3328) TV stick, it got bricked. I searched the internet and tried many methods to recover it, but failed, please help if you know a better solution.
I used RKBatchTool to restore it, and got a blue square, but after I click "restore" button, it failed at "Prepare idb fail"
I also tried RK Android Tool, and Factory Tool my stick is loaded as "Found one MASKROM Device". I played around the tool, but every time it failed at the same reason "Prepare idb fail ".
I have no ideas, anyone please help!
Flash Info:
Manufacturer: SAMSUNG,value=00
Flash Size: 0MB
Block Size: 512KB
Page Size: 2KB
ECC Bits: 0
Access Time: 40
Flash CS: Flash
billi69 said:
I have a T9 4GB/64GB TV BOX (RK3328) TV stick, it got bricked. I searched the internet and tried many methods to recover it, but failed, please help if you know a better solution.
I used RKBatchTool to restore it, and got a blue square, but after I click "restore" button, it failed at "Prepare idb fail"
I also tried RK Android Tool, and Factory Tool my stick is loaded as "Found one MASKROM Device". I played around the tool, but every time it failed at the same reason "Prepare idb fail ".
I have no ideas, anyone please help!
Flash Info:
Manufacturer: SAMSUNG,value=00
Flash Size: 0MB
Block Size: 512KB
Page Size: 2KB
ECC Bits: 0
Access Time: 40
Flash CS: Flash
Click to expand...
Click to collapse
It sounds like a Roku stick and you did something to brick it. Unfortunately you may not be able to recover it as I've not seen any restore method
To fix this box and I have done this to 3 of them already. All of them are the 64GB 4GB ones. Good thing you crashed the onboard rom otherwise it would not start recovery. Get an SD card in 16GB or larger. Look for SD_Firmware_Tool.exe online and the file you want to put on the SDcard is the Android 9.0 PIE is 3318_9.0-TVBOX-Z4_1025.img
Once the SD card is created put it in the Android TV box. Then power on the box and the recovery will begin on its own right away. Once its done. It will tell you to remove the SD card which it will reboot itself once its out. Then it will run an Erase mode setting up the user partition which takes a min. Then it will boot. The first boot takes a few mins. As long as you see the colorful splash screen your good just wait.
Get the unit online and use the update tool to grab and install the latest 9.0 pie update. Once your done its recovered.
Now I have found the SDcard I used to recover these devices once its formatted it will not boot while inserted in the android box. I think a boot flag was set and since it can't locate the files it refuses to boot. The cheap work around is use a brand new Sdcard that was not used for recovery process.
I also noticed the Wifi and Ethernet will not work at the same time in 9.0 like it did in 8.1. The remotes works fine and Bluetooth works still. If you want Kodi latest version uninstall the KDplayer that comes with it. I recommend getting rid of the apps you do not use.
I also notice the Playstore does not install apps but if you use a computer or phone to pick your apps and tell it to install to the TV box it will work then or manually install your .APK's also works. Once the programs are installed they will update afterwards.
I have been looking for Android 10 but no luck yet.
I never ever had luck using the rockchip USB to USB cable to PC to work. It will error out no matter what. Forget going that route.
Hello:
I have the same problem and I want to test what you comment
Where can I get the files that you comment, for example the 3318_9.0-TVBOX-Z4_1025.img?
Thanks a lot
karldry said:
Hello:
I have the same problem and I want to test what you comment
Where can I get the files that you comment, for example the 3318_9.0-TVBOX-Z4_1025.img?
Thanks a lot
Click to expand...
Click to collapse
Uploaded them to my shared Onedrive here. Grab the SD firmware tool too from my onedrive link here at
Microsoft OneDrive - Access files anywhere. Create docs with free Office Online.
Store photos and docs online. Access them from any PC, Mac or phone. Create and work together on Word, Excel or PowerPoint documents.
1drv.ms
all you gotta do is have a sdcard with nothing on it. Make it fat32 on the PC. Open the SD card firmware tool. Make sure the top field has your SD card listed.
Click Upgrade firmware option box.
Then load the firmware file by clicking the firmware button.
Then click create.
This will take awhile to write 2GB of data to an SDcard.
Once it's done. Put it on the TV box with the power off. Plug the HDMI cable in. Insert the SDcard in the TF slot.
Then power on the tv box and it will start programming process right away. Leave it be since it takes awhile to do its thing. It will tell you to remove the SD card when done. Once the SD card is removed the box will reboot on its own. You will see the message erasing which takes about 2 minutes. Then it will boot with the T9 logo screen. The first boot takes about 4 minutes to finally start up.
Once you get it online use the updater tool on the menu option. It will update the box. Keep the Sd card just incase it does brick itself. It happened once on one of my boxes. Just pop in the recovery SD card to start over again if it happens to you.
Note for some reason the SD card you use for recovery will not allow the tv box to boot if decide to use it for storage. I believe it sets a boot flag in the SD card firmware and fails when the files are gone. Not sure how to clear it. Hey they are dirt cheap anyways for a new one.
Oh and do not reinsert this sdcard after you set it up. A power cycle will start the recovery process again.
Thank you very much for your help. I try it and tell you how it went
karldry said:
Thank you very much for your help. I try it and tell you how it went
Click to expand...
Click to collapse
Did you recover it yet?
flood404 said:
Uploaded them to my shared Onedrive here. Grab the SD firmware tool too from my onedrive link here at
Microsoft OneDrive - Access files anywhere. Create docs with free Office Online.
Store photos and docs online. Access them from any PC, Mac or phone. Create and work together on Word, Excel or PowerPoint documents.
1drv.ms
all you gotta do is have a sdcard with nothing on it. Make it fat32 on the PC. Open the SD card firmware tool. Make sure the top field has your SD card listed.
Click Upgrade firmware option box.
Then load the firmware file by clicking the firmware button.
Then click create.
This will take awhile to write 2GB of data to an SDcard.
Once it's done. Put it on the TV box with the power off. Plug the HDMI cable in. Insert the SDcard in the TF slot.
Then power on the tv box and it will start programming process right away. Leave it be since it takes awhile to do its thing. It will tell you to remove the SD card when done. Once the SD card is removed the box will reboot on its own. You will see the message erasing which takes about 2 minutes. Then it will boot with the T9 logo screen. The first boot takes about 4 minutes to finally start up.
Once you get it online use the updater tool on the menu option. It will update the box. Keep the Sd card just incase it does brick itself. It happened once on one of my boxes. Just pop in the recovery SD card to start over again if it happens to you.
Note for some reason the SD card you use for recovery will not allow the tv box to boot if decide to use it for storage. I believe it sets a boot flag in the SD card firmware and fails when the files are gone. Not sure how to clear it. Hey they are dirt cheap anyways for a new one.
Oh and do not reinsert this sdcard after you set it up. A power cycle will start the recovery process again.
Click to expand...
Click to collapse
Hi, thank you for this detailed reply.
I am having the same problem with T9 (RK 3318) TV box 64GB 4GB bricked with wrong firmware when I tried to upgrade from Android 8.1 to 9.0.
There is nothing on it whenever I powered up this TV box.
Can I use the same method above to recover the bootup?
All of us would appreciate your advise.
Thank you.
Benny154 said:
Hi, thank you for this detailed reply.
I am having the same problem with T9 (RK 3318) TV box 64GB 4GB bricked with wrong firmware when I tried to upgrade from Android 8.1 to 9.0.
There is nothing on it whenever I powered up this TV box.
Can I use the same method above to recover the bootup?
All of us would appreciate your advise.
Thank you.
Click to expand...
Click to collapse
Yes it works. I was able to update all three of the boxes I own to the 9.0 Version. The playstore on the 9.0 sucks. Better off installing and maintaining your updates with pureAPK instead of playstore. Remember the SD card will not be useable on the T9 boxes after carrying out the update for additional storage. It can always be used to restore the boxes if something happens. I was able to use the SD card in other devices.
flood404 said:
Yes it works. I was able to update all three of the boxes I own to the 9.0 Version. The playstore on the 9.0 sucks. Better off installing and maintaining your updates with pureAPK instead of playstore. Remember the SD card will not be useable on the T9 boxes after carrying out the update for additional storage. It can always be used to restore the boxes if something happens. I was able to use the SD card in other devices.
Click to expand...
Click to collapse
Thank you for your fast reply.
I m trying to create the SD Card with img file but failed with error message (attached picture).
My TV box is made of RK3318, not RK 3328 chipset. I m trying out your method..
Do I need to short any pin to unbrick the Circuit board?
I appreciate your advice, please. Thank you.
Is that a 2Tb card? Use a 32GB one or smaller as long its 8GB to 32GB in size. There was no pin shorting needed. Just create the SDcard and put it on the TV box port and power on tv box.
flood404 said:
Is that a 2Tb card? Use a 32GB one or smaller as long its 8GB to 32GB in size. There was no pin shorting needed. Just create the SDcard and put it on the TV box port and power on tv box.
Click to expand...
Click to collapse
Thank you for your guidance.
Make sure windows is not blocking the file by right clicking on the properties of it and click unblock and apply. Also I would run the SD creation tool with admin rights.
flood404 said:
Make sure windows is not blocking the file by right clicking on the properties of it and click unblock and apply. Also I would run the SD creation tool with admin rights.
Click to expand...
Click to collapse
Hi. thks for your kind guidance.
I managed to create Bootrom Img disk using SD Card. However, my T9 TV box cannot be powered up. I suspect that the IC chip was damaged. This TV box was bricked when the vendor supplied me the wrong Img file. I realised it after I opened up the TV box cover.
Time to dump off the TV box.
Good afternoon,
I am looking for a stock version for the T9 TV Box 32GB/4GB RK3318. some months ago, I bought a TUREWELL T9, however it is not allowing to run Disney+ anymore and I am not able to upgrade the device. Hence I was hoping that the above solution would work with a stock version of Andoid.
Any help is greatly appreciated. Thanks in advance.
I can't find the image file Android 9.0 PIE is 3318_9.0-TVBOX-Z4_1025.img
Can someone post a valid link from Google drive?
maki_xda said:
I can't find the image file Android 9.0 PIE is 3318_9.0-TVBOX-Z4_1025.img
Can someone post a valid link from Google drive?
Click to expand...
Click to collapse
Google Drive: Sign-in
Access Google Drive with a Google account (for personal use) or Google Workspace account (for business use).
drive.google.com
flood404 said:
Google Drive: Sign-in
Access Google Drive with a Google account (for personal use) or Google Workspace account (for business use).
drive.google.com
Click to expand...
Click to collapse
Can't access it
maki_xda said:
Can't access it
Click to expand...
Click to collapse
I did get a unknown Gmail account wanting to access it. I did not know if it was you or not.
flood404 said:
I did get a unknown Gmail account wanting to access it. I did not know if it was you or not.
Click to expand...
Click to collapse
It was me, most likely