Tried rooting my phone, stuck on startup screen and download mode.
Didn't work so I am now trying to install stock firmware.
When in Odin3, there are different things that happen. It says "Added!!" Sometimes I get stuck at setupconnection, but other times it initializes and i get a nand write start fail.
I am using Odin3 v3.10.6
<ID:0/004> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> G925FXXU1AOCV_G925FH3G1AOC1_G925FXXU1AOCW_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Odin engine v(ID:3.1005)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> SingleDownload.
<ID:0/004> sboot.bin
<ID:0/004> NAND Write Start!!
<ID:0/004> FAIL!
<ID:0/004>
<ID:0/004> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
I also get this failure sometimes
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> G925FXXU1AOCV_G925FTEF1AOC1_G925FXXU1AOCW_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Added!!
<ID:0/004> Odin engine v(ID:3.1005)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
SM-G925F
I have already tried different USB ports, different cables
I can't restart because on the boot screen i get a "recovery is not seandroid enforcing" message.
I'm having the same issue with a non-edge S6, did you find a way to solve it? How did you solve it?
how long does it take normally to flash a rom? I'm trying to flash a stock rom from a hard brick and my odin just sits at setup connection and doesn't move and doesn't get an error either.
If it is hard bricked then nothing short of a jtag will save it.
Related
I bricked my i9100m. Please help!!
So, I was fooling around with flashing a modem in Odin and it failed. My phone ended up saying "Firmware upgrade encountered an issue. Please select recovery mode in Kies & try again." when I try to go into recovery mode.
I can get into download mode, but when I tried to flash stock firmwares each one failed. I did flash multiple different kernels too. They get rid of the message above, but then it's stuck in boot screen with a yellow triangle.
I was running the leaked 4.1.2 official rom rooted and deodexed before I bricked it. My phone is a Bell Mobility phone from Canada Model i9100M.
<ID:0/004> Removed!!
<ID:0/004> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9100MUGLD3_I9100MBMCLD3_I9100MXXLD3_HOME.tar.md5 is valid.
<OSM> I9100MUGLD3_I9100MBMCLD3_I9100MXXLD3_HOME.tar.md5 is valid.
<OSM> I9100MUGLD3_I9100MBMCLD3_I9100MXXLD3_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Odin v.3 engine (ID:4)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> boot.bin
<ID:0/004> NAND Write Start!!
<ID:0/004>
<ID:0/004> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
I don't knwo what else to try. Please help. I just want my phone to work again.
UPDATE!
I fixed it. For some reason the same process worked on my laptop and not my desktop.
T12UNK5 said:
I bricked my i9100m. Please help!!
So, I was fooling around with flashing a modem in Odin and it failed. My phone ended up saying "Firmware upgrade encountered an issue. Please select recovery mode in Kies & try again." when I try to go into recovery mode.
I can get into download mode, but when I tried to flash stock firmwares each one failed. I did flash multiple different kernels too. They get rid of the message above, but then it's stuck in boot screen with a yellow triangle.
I was running the leaked 4.1.2 official rom rooted and deodexed before I bricked it. My phone is a Bell Mobility phone from Canada Model i9100M.
<ID:0/004> Removed!!
<ID:0/004> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9100MUGLD3_I9100MBMCLD3_I9100MXXLD3_HOME.tar.md5 is valid.
<OSM> I9100MUGLD3_I9100MBMCLD3_I9100MXXLD3_HOME.tar.md5 is valid.
<OSM> I9100MUGLD3_I9100MBMCLD3_I9100MXXLD3_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Odin v.3 engine (ID:4)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> boot.bin
<ID:0/004> NAND Write Start!!
<ID:0/004>
<ID:0/004> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
I don't knwo what else to try. Please help. I just want my phone to work again.
Click to expand...
Click to collapse
Your device was never "bricked".
Hi, I followed everything in the how to get root video on the Galaxy S4, but when I tried to flash it to the 423399 kernal (so I can eventually obtain root), it failed. No I am stuck. I can only get to the odin download screen and if I just try to boot it normally it goes to the firmware upgrade encountered an issue. Please select recovery mode in Kies & try again. When I reboot into Odin download, its connected and I load the 423399 into PDA then Start. Here's what I get.
<ID:0/004> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> SCH-I545_MD2_423399_Kernel.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Odin v.3 engine (ID:4)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Get PIT for mapping..
<ID:0/004> Removed!!
<ID:0/004> There is no PIT partition.
<OSM> All threads completed. (succeed 0 / failed 1)
I don't know why but it keeps Removing. I am no longer getting a blue load bar under the Downloading... Do not turn off target!!
I can not get into recovery mode either.
Any help would be much apprectiated!
I tried the "Unbrick method" by flashing the stock restore. Didn't work.
<ID:0/004> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> SCH-I545_MDK_562219_Stock_Restore.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Odin v.3 engine (ID:4)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Removed!!
<ID:0/004> Get PIT for mapping..
<ID:0/004> There is no PIT partition.
<OSM> All threads completed. (succeed 0 / failed 1)
PaulJ69 said:
I tried the "Unbrick method" by flashing the stock restore. Didn't work.
<ID:0/004> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> SCH-I545_MDK_562219_Stock_Restore.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Odin v.3 engine (ID:4)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Removed!!
<ID:0/004> Get PIT for mapping..
<ID:0/004> There is no PIT partition.
<OSM> All threads completed. (succeed 0 / failed 1)
Click to expand...
Click to collapse
is usb debugging turned on on the phone?
theidoctor said:
is usb debugging turned on on the phone?
Click to expand...
Click to collapse
He said he can't get his phone to load so therefore he can't enable USB debugging. I sent you some info to try and assist you. Message me back if you need anything.
So after trying a ton of different things and kept getting the same
<ID:0/004> Initialzation..
<ID:0/004> Removed!!
I figured it was something on my end removing the connection. I took out the USB cable and plugged it directly into the back of the motherboard and Bingo! it worked!
Thanks again DarkMenace for sticking it out with me!
PaulJ69 said:
So after trying a ton of different things and kept getting the same
<ID:0/004> Initialzation..
<ID:0/004> Removed!!
I figured it was something on my end removing the connection. I took out the USB cable and plugged it directly into the back of the motherboard and Bingo! it worked!
Thanks again DarkMenace for sticking it out with me!
Click to expand...
Click to collapse
Anytime.
Sent from my Rooted Verizon Samsung Galaxy S4 using xda premium
Hi everyone,
So i'm new to firmwares and stuff.
So my phone recently stuffed up by for whatever reason restarting itself and freezing on the 'samsung gt-i9300t' screen.
So i went on to download mode and tried using the firmware provided by sammobile and used it with Odin but it didnt work. here is what the message says
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9300TDUELL2_I9300TTELELL2_I9300TDUELL2_HOME.tar.m d5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> All threads completed. (succeed 0 / failed 0)
<ID:0/007> Added!!
<ID:0/007> Odin v.3 engine (ID:7)..
<ID:0/007> File analysis..
<ID:0/007> SetupConnection..
<ID:0/007> Initialzation..
<ID:0/007> Get PIT for mapping..
<ID:0/007> Firmware update start..
<ID:0/007> tz.img
<ID:0/007> NAND Write Start!!
<ID:0/007> FAIL!
<OSM> All threads completed. (succeed 0 / failed 1)
Some notes-
*recovery mode does not work, it just restarts the phone
*the phone is from the telstra company in australia
*i havent installed any roms before so it's been running on android
spaghettisauce said:
Hi everyone,
So i'm new to firmwares and stuff.
So my phone recently stuffed up by for whatever reason restarting itself and freezing on the 'samsung gt-i9300t' screen.
So i went on to download mode and tried using the firmware provided by sammobile and used it with Odin but it didnt work. here is what the message says
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9300TDUELL2_I9300TTELELL2_I9300TDUELL2_HOME.tar.m d5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> All threads completed. (succeed 0 / failed 0)
<ID:0/007> Added!!
<ID:0/007> Odin v.3 engine (ID:7)..
<ID:0/007> File analysis..
<ID:0/007> SetupConnection..
<ID:0/007> Initialzation..
<ID:0/007> Get PIT for mapping..
<ID:0/007> Firmware update start..
<ID:0/007> tz.img
<ID:0/007> NAND Write Start!!
<ID:0/007> FAIL!
<OSM> All threads completed. (succeed 0 / failed 1)
Some notes-
*recovery mode does not work, it just restarts the phone
*the phone is from the telstra company in australia
*i havent installed any roms before so it's been running on android
Click to expand...
Click to collapse
tried flashing it again and it said
<ID:0/007> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9300TDUELL2_I9300TTELELL2_I9300TDUELL2_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/007> Odin v.3 engine (ID:7)..
<ID:0/007> File analysis..
<ID:0/007> SetupConnection..
<ID:0/007> Can't open the serial(COM) port.
<OSM> All threads completed. (succeed 0 / failed 1)
spaghettisauce said:
tried flashing it again and it said
<ID:0/007> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9300TDUELL2_I9300TTELELL2_I9300TDUELL2_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/007> Odin v.3 engine (ID:7)..
<ID:0/007> File analysis..
<ID:0/007> SetupConnection..
<ID:0/007> Can't open the serial(COM) port.
<OSM> All threads completed. (succeed 0 / failed 1)
Click to expand...
Click to collapse
does usb debugging is enabled check that
then use a different odin
sangalaxy said:
does usb debugging is enabled check that
then use a different odin
Click to expand...
Click to collapse
um i downloaded the drivers for my phone but im not sure how to check if debugging is on
should i use an older version of odin then?
sangalaxy said:
does usb debugging is enabled check that
then use a different odin
Click to expand...
Click to collapse
i tried what you said and this message shows up
<ID:0/008> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9300TDUELL2_I9300TTELELL2_I9300TDUELL2_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/008> Odin v.3 engine (ID:8)..
<ID:0/008> File analysis..
<ID:0/008> SetupConnection..
<ID:0/008> Initialzation..
<ID:0/008> Get PIT for mapping..
<ID:0/008> Firmware update start..
<ID:0/008> tz.img
<ID:0/008> NAND Write Start!!
<ID:0/008>
<ID:0/008> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1
spaghettisauce said:
i tried what you said and this message shows up
<ID:0/008> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9300TDUELL2_I9300TTELELL2_I9300TDUELL2_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/008> Odin v.3 engine (ID:8)..
<ID:0/008> File analysis..
<ID:0/008> SetupConnection..
<ID:0/008> Initialzation..
<ID:0/008> Get PIT for mapping..
<ID:0/008> Firmware update start..
<ID:0/008> tz.img
<ID:0/008> NAND Write Start!!
<ID:0/008>
<ID:0/008> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1
Click to expand...
Click to collapse
debugging is on settings-applications-development check that
and try an older version of odin1.85 will be better
try and post
sangalaxy said:
debugging is on settings-applications-development check that
and try an older version of odin1.85 will be better
try and post
Click to expand...
Click to collapse
i cant get to the debug option my phone is frozen in boot screen. odin 1.85 shows-
<ID:0/007> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9300TDUELL2_I9300TTELELL2_I9300TDUELL2_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/007> Odin v.3 engine (ID:7)..
<ID:0/007> File analysis..
<ID:0/007> SetupConnection..
<ID:0/007> Initialzation..
<ID:0/007> Get PIT for mapping..
<ID:0/007> Firmware update start..
<ID:0/007> tz.img
<ID:0/007> NAND Write Start!!
<ID:0/007>
<ID:0/007> Complete(Write) operation failed.
spaghettisauce said:
i cant get to the debug option my phone is frozen in boot screen. odin 1.85 shows-
<ID:0/007> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9300TDUELL2_I9300TTELELL2_I9300TDUELL2_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/007> Odin v.3 engine (ID:7)..
<ID:0/007> File analysis..
<ID:0/007> SetupConnection..
<ID:0/007> Initialzation..
<ID:0/007> Get PIT for mapping..
<ID:0/007> Firmware update start..
<ID:0/007> tz.img
<ID:0/007> NAND Write Start!!
<ID:0/007>
<ID:0/007> Complete(Write) operation failed.
Click to expand...
Click to collapse
do you have kies running
If yes disable that
and be sure that you have the correct usb drivers or kies installed
and you can also try without battery
take out the battery and connect to pc then go into download mode
sangalaxy said:
do you have kies running
If yes disable that
and be sure that you have the correct usb drivers or kies installed
and you can also try without battery
take out the battery and connect to pc then go into download mode
Click to expand...
Click to collapse
i dont have kies and ive got the correct drivers
spaghettisauce said:
i dont have kies and ive got the correct drivers
Click to expand...
Click to collapse
the better is uninstall drivers and install kies and try connecting if you computer recognizes just fine the go with as above said without battery
sangalaxy said:
the better is uninstall drivers and install kies and try connecting if you computer recognizes just fine the go with as above said without battery
Click to expand...
Click to collapse
my phone doesnt turn on without battery
spaghettisauce said:
my phone doesnt turn on without battery
Click to expand...
Click to collapse
go into download mode after connecting to pc it will work without battery
hello,
I just try my Tab2 also to flash. I get always the flash process via odin following message:
Code:
<ID:0/004> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> GT-P5110_CWM_6.0.5.1.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Odin v.3 engine (ID:4)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Get PIT for mapping..
<ID:0/004> There is no PIT partition.
<OSM> All threads completed. (succeed 0 / failed 1)
Can anybody help me?
Greetings Coldjack
coldjack said:
hello,
I just try my Tab2 also to flash. I get always the flash process via odin following message:
Code:
<ID:0/004> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> GT-P5110_CWM_6.0.5.1.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Odin v.3 engine (ID:4)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Get PIT for mapping..
<ID:0/004> There is no PIT partition.
<OSM> All threads completed. (succeed 0 / failed 1)
Can anybody help me?
Greetings Coldjack
Click to expand...
Click to collapse
It might be the same mistake I made when flashing my phone.. I didn't run Odin as administrator in win7. After I did run it as administrator the error was gone.
But.... I also had a similar error with bad files so it could be that too.
Sent from my GT-P7510 using XDA Free mobile app
Hi, l made it as Administrator.
And there comes the error.
Greetings coldjack
Hi,
I tried to fix an old Note 10.1 GT-N8005 which is in a boot loop, it displays the Samsung Note Logo and resets forever. I can run Odin with Volume -.
I tried Odin on W10 with a stock file and Odin says it's a success (see below), but the Boot loop is still there. Odin on the tablet gives a strange information, that says INVALID RPMB DATA.
I googled around, I found that there might be a problem with the eMMC, might... I don't think so, because my wife told me, that the tablet worked ok until Samsung started an OTA Update, since the there is a boot loop. I don't think, that a Update can damage the hardware.
Any idea how to fix ist, if this error occurs and the eMMC might be ok?
<ID:0/004> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Odin engine v(ID:3.1401)..
<ID:0/004> File analysis..
<ID:0/004> Total Binary size: 1673 M
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Set PIT file..
<ID:0/004> DO NOT TURN OFF TARGET!!
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> NAND Write Start!!
<ID:0/004> SingleDownload.
<ID:0/004> sboot.bin
<ID:0/004> param.bin
<ID:0/004> tz.img
<ID:0/004> boot.img
<ID:0/004> recovery.img
<ID:0/004> system.img
<ID:0/004> cache.img
<ID:0/004> hidden.img
<ID:0/004> RQT_CLOSE !!
<ID:0/004> RES OK !!
<ID:0/004> Removed!!
<ID:0/004> Remain Port .... 0
<OSM> All threads completed. (succeed 1 / failed 0)
Click to expand...
Click to collapse