Hello guys, I have a HiSense U970 with the MT6589 chipset which got hard bricked a week ago. The phone is running a stock 4.2.1 JB and rooted. The problem is that whenever I try to flash anything using SP Flash Tool it shows this error:
BROM ERROR : S_FT_ENABLE_DRAM_FAIL (4032)
[EMI] Enable DRAM failed
I am hopeful the phone isn't totally dead since it can be:
- Detected by the computer WITHOUT the battery while holding vol down
- In Device Manager, it would show MTK USB Port (ComX) under Ports when vol down is held.
This is what happens now:
- Charging does not do anything.
- Cannot boot into recovery
- Cannot be detected by MTK Droid Tools (but I think this app needs a powered up phone to be detected by its system)
- Cannot flash anything using SPFT v3.1320.0.174 and v5.1524.00
I have searched the internet for fixes and solutions but, everything that I have found leads to that error.
Here was what I had done before the problem arose.
- Installed Preloader driver
- Used the latest version of SPFT
- Formatted whole flash except bootloader as I cannot flash the cwm rom found here without formatting
- Flashed ONLY the recovery and then downloaded it.
Green circle appears and after that, it cannot boot anymore. Cannot charge. Cannot boot into recovery.
I have tried the following with no luck:
- Used SPFT v5.1524.00 and v3.1320.0.174
- Flashing only the preloader
- Flashing only the recovery
- Format whole flash
- Formatting whole flash except bootloader
- Format all + download (v5)
- Firmware upgrade + upgrade (v3)
- Using the write memory method for writing preloader
- Flashing stock preloader
- Doing a memory test
All of which goes to the error 4032.
I have also tried using different USB ports with the same results.
If it helps, I used the scatter file for MT6589 and not my own scatter file. Using my own scatter file does not do anything before I flashed the recovery rom so, I used the MT6589 scatter file instead. Also, my scatter file was different from the MT6589.
- This was the scatter file I used.
- And this is my log from MTK Droid Tools which hopefully contains the addresses for the scatter file (I accidentally replaced my own [yea i know, stupid me])
I also cannot find the same scatter file that I had created anywhere on the internet.
I am willing to supply you with anything as long as I have access to it (hoping I have the file/information you need:fingers-crossed.
I am hoping that you know or at least the very least, can guide me out of mine and others misery. Thank you. :fingers-crossed:
Related
hi.I used SP Flash Tool to flash my phone with the wrong ROM and now its DEAD.It won't turn on.it won't charge and still PC detection as Mtk Usb Port.
I have another same device.i get backup of stock ROM with Mtk Droid Tool.(i know backup files work.recovery file with scatter flashed sucsesfully when i install cwm recovery on new device)
i can format whole flash with SPFT and get green circle.
then try to download,but this errors appeared.
with SP FLASH TOOL 3.1224.01 : S_DL_GET_SETTING_FAIL (5054)
with SP FLASH TOOL 3.1304.0.119 :S_DA_DRAM_NOT_SUPORT (3004)
i see this error too : booloader doesnt exist on nand flash.please download bootloader first!
i think its bootloader problem so maybe testpoint method works.problem is i dont know which one is TP and how can i use it.
cpu : mtk6517(6577)
ram:512
android :4.0.4
http://www.apanda.com.cn/a60t/
anyone.please help
Hello!
I have a bricked phone. When I got him, he was in a state "loaded to the screensaver and stop".
I decided to flash him using recovery (carliv touch recovery 2.2). Thanks to recovery I copied all the files from phone. But all my attempts of flashing were unsuccesful - I've got the errors while recovery did an unzipping.
That because I decided to use SP FlashTool. But I've forever got the same error 5069.
I notice, that I can format my phone and download the preloader. But it's all what I can.
What I tried (what i remember):
to load without and with battery;
to put a battery after beginning of flashing;
to flash with pushed power, volume control buttons - all together and alone
to use another system, cable and computer (2 cables and computers, windows and ubuntu);
to flash different versions (from off site);
to use different versions of sp flashtool
Also I found a video, where propose to do the backup of working phone (prestigio 3400) by MTK droid tool and try to flash this.
I would be very grateful if you help me. Thanks
My phone xtouch PF73 gives me this message "decrypt error, boot failed" after i tried flashing it.
I have tried two more ROMS but with those i get the "S_NOT_ENOUGH_STORAGE(1011) error message in both SP Flash tool and WiseLink Tool"
Android version: 4.22
MTK platform : MT6572
I used
SP Flash Tool v5.1352.01
SP Flash Tool v5.1628
wise tool v4.6.0.44
How can i fix it?
hi i also have alcatel 4035D im trying to load firmware using sp tool but its giving me an error 1011, i have tried different firmwares
nyado said:
hi i also have alcatel 4035D im trying to load firmware using sp tool but its giving me an error 1011, i have tried different firmwares
Click to expand...
Click to collapse
Reason:
The firmware(s) you are trying to flash to your MTK device is larger than the available space allocated for the firmware in the phone’s storage space.
Possible fix ( was not tested by me ):
Click on the Format Tab
Select/tick Format whole Flash and click the Start button before connecting your device.
Once the formatting is done, go to the Download Tab and select just the Preloader file first and flash it.
After the preloader.bin has been successfully flashed to your device, tick the rest of the firmware files and flash as well.
So basically monky, windows crapped on my boot partition trough fastboot, i dont have anymore acces to recovery or fastboot to reflash the boot partition.
I was trying to fix it trough the mighty SP Flash Tool since i have an MT6750(T) board but any tutorials ive looked up so far require an MTK DA USB device connected wich i dont see even if i unplug the batter, hold volume / whatever.
Only Preload and USB show up in devices. I tried to flash when Preload was connected but the only problem is that Preload device disconnects after a very short amount of time : SP Flash Tool doesn't have time to go in the flash state, it just goes to 100% DA wich after it errors due to the Preload diseapearing, and i can't flash while the MTK USB device is on, i don't know what can i do with it, any advice for that MT6750(T) board ?
(the errors generated by the tool were either, Preload file invalid (?) or disconnet battery and retry while holding volume down wich obv didnt work)
Gigaset GS270+
Android 8.1
Hello all good souls over here.
Could you please help me out with flashing back the original stock ROM to Mediatek MT6737M phone?
UMAX VisionBook P50 LTE, Mediatek MT6737M, 2GB RAM, 16GB internal memory.
What happened:
Before I was trying Oukitel P5 Pro ROM as well as Lineage OS and flashing with SP Flash Tool was working just perfectly.
But then I tried to flash Oukitel P5 Pro Andorid 7 stock ROM. (Oukitel P5 Pro and UMAX VisionBook P50 LTE are completely the same phones. Just different branding)
(And from now on I am not sure if I remember correctly)
When I loaded in scatter file, SP Flash Tool said something about something .... and recommended to do "Format all + Download" and I have done so.
Clicked on the Download button, flashing started instntly when I connected the phone while holding Volume - button.
Flashing stopped in maybe one second with the error which I do not remember as I closed the error window way too quickly. :-(
Later on I noticed that the preloader file is different in this Android 7 ROM then Android 6 ROM.
What is the current behavior:
When the phone is connected (with the battery inside) to the computer phone keeps connecting and disconnecting (appearing in Device manager as Mediatek USB Port) if I click Download button it starts doing "something" instantly which stops at Download DA 100% and after the while ERROR: S_FT_ENABLE_DRAM_FAIL (4032) pop up windows shows up.
The same error happens if I try to Format it and all other combinations in Download tab (Firmware upgrade, Format All + Download)
If I plug in the phone to the computer while pressing Volume - button phone will show up in the Device manager after about 20 seconds.
(Just to note - When the phone was working OK, I started flashing instantly when I plug the phone into the computer while pressing the Volume - button
So that kind of leads me that if nothing will show up in Device manager when I plug the phone to the computer while pressing Volume - button, then there might be the issue with the phone not switching into META mode? Not sure, just what I have read. But I cannot move any forward at this point.)
What I have tried:
- Correct stock ROM and Oukitel stock ROM (both Android 6 and both I was able to flash correctly and was able to boot them, until I tried Android 7 ROM)
- various SP Flash Tools 5.xxxx (and 3.xxxx too, but version 3 does not accept scatter file at all)
- USBDeview and removing all related USB devices from Windows and re-install them back again.
- Various VCOM drivers I have found on the Internet
- Flashing with SP Flash Tools on Linux (ends up with the exact same result - 4032)
- I tried shorting test point to ground on the phone main board. (The result was the same like when I plug the phone in while holding the Volume - button - Phone would not show up in Device manager for about 20 seconds)
- Tried flashing with the battery inside and outside the phone. (When the battery is outside flashing would not start, but the error about incorrect chip type will show up)
- Read many articles about this error all over the Internet
Do any of you think there is a change to bring the phone back to live? Or do you know what actually might happen to the phone? It does not seems to be completele bricked, but I cannot say in what state the phone is.
Thank you very much for your help and have a nice day.
Hi. I need this rom for this phone. I have umax p50 lte too . Please give me link if you can. Thx
@oukitel654
Look inside here:
Common SP Flash Tools error and Solutions - ROM-Provider
Common SP Flash Tools error and Solutions: Hello guys if you are facing a SP Flash tools error code issue then this page is for you where we share solutions for for almost all SP Flash tools error. Common SP Flash Tools error Code: Error 5054, 4032, 8038, 5069, 4001, 4008, 3149, 3168, 2004, 1013, …
romprovider.com