Phone bricked + unable to connect it via usb - Android Q&A, Help & Troubleshooting

Hi, I was asked to post my help-request in this board
http://forum.xda-developers.com/general/xda-assist/phone-totally-bricked-t3248796
So, my phone is hard-bricked (doesn't boot at all) and it's no longer responding when connecting it via usb cable. I was about to flash it but couldn't complete the operation, now everything is deleted including the operation system (the ROM), the recovery mode, the preloader etc....
So what to do?
my phone is versus pioneer p1 ( a.k.a gionee pioneer p1)
Thanks.

Related

[Q] Mtk6577 Preloader dead/restarts

Here is my complete problem,
My device is Micromax a110(canvas 2) (AKA Cynus t2 or Qmobile a10) (The board is s9081).
I was in CWM and i flashed the galaxy custom rom(meant for my device) it worked nicely after due to some reasons i rebooted it on factory mode after that the device went to bootloop, the bootscreen shows and then restarts infinitely , so i decided to reflash the stock rom (Stock recovery) so that i removed the battery and connected the phone via usb, now my phone detected as MT65xx preloader and in a second it disappers instantly. i tried testpoint too it doest works ,it is not the driver problem since the device needs to be detected and stay detected for that long to install the drivers(and i do have the drivers), is there any solutions for that? any help is appreciated, thanks in advance.

[Q] Help flashing Alcatel C7 that boots automatically when plugging the USB

Hello,
During the past days I've been trying to flash my C7 with no success. When pressing power button, it turns on and displays the Alcatel logo but stays there, it does not load the OS.
I have tried to use SPtools to flash it, I have the mtk drivers installed in my PC. When I plug the switched-off phone to the computer it turns on and couple seconds after my PC detects it (I can see the preloader mtk loaded on the device manager); however, one second right after it is detected, it is disconnected as it keeps booting to show the logo and stay there. Obviously, if the phone is not detected I cannot use SPtools to flash it.
Any suggestion will be highly appreciated.
PS: I have also tried to connect to it with adb, and dump a ROM using sideload with no sucess, the PC recognizes it from the recovery but after copying the image nothing new happens on reboot.

MTK Preloader Isn't Showing Up in Device Manager for My Phone

I have a Digicel DL750. I understand that it is an Alcatel Pop C3 upgraded to a KitKat.
My phone is hard bricked. I followed the procedures to connect it to the PC whilst off and without battery. Nothing happens. No connecting sound on my PC... until I hold the power, volume up and volume down buttons.
My sister has the same phone. Hers connect whilst off and without battery. I even see the MTK Preloader in the device manager, so her phone connected successfully. For me what shows up is Alcatel Mobile Phones (COM5) and after reinstalling the driver I see MTK USB Port.
I have the Sp Flash Tool-ready files to flash unto the device.
I just need the phone to connect like it should. Can you assist me?
Is my phone dead?

[help] Lenovo S6000L bricked (?)

Some wanker had posted wrong images for boot and recovery for S6000L. And since I'm a moron, i didn't take the files apart to check them.
Installing them bricked my tablet. So essentially I have no boot or recovery images on the device and was wondering if there's any way to revive it.
Tablet freezes if i start it in normal, fastboot or recovery modes, so that's out of the picture.
However, i think that "meta mode" still works (if indication of it working is displaying lenovo logo and having "meta mode" written on the bottom of the screen)
It's getting detected on "mediatek preloader usb vcom port" for a couple of seconds when connected to the PC, which means that i might be able to use adb to push a backup into the tablet (?)
Been scouring the internet for a while with no results. Is there, by any chance, anyone who can help me out?

ZTE Nubia N1 Lite: Broken USB/Fastboot?

Hi,
I've got a Nubia N1 Lite (NX597J) to mess around with, and wanted to try modifying the ROM. I can enter developer mode and allow bootloader unlocking, adb also works. What I can't do is use USB while booting, or in the recovery menu. No fastboot or sending ROM images via adb to the recovery software. The phone doesn't connect to the computer at all (I'm using Linux, it should at least show up in dmesg). Recovery log says
Code:
musb_pullup 2498: no USB cable, don't need to turn on USB
A couple times, even though the cable is connected and works in Android proper. I've tried USB2 and 3 ports, on a hub and directly on the motherboard. It shows up as 0e8d:2000 MediaTek preloader when turned off and, very briefly, as 0e8d:2008 when booting into recovery.
Am I missing something, or is the recovery image just broken on this phone? I've tried both the EU and US firmware, which is a bit more recent.
Do I need some tool that interacts with the preloader, maybe? I have found this guy who's been messing with a phone that has the same SoC.
Have you managed to get it into recovery mode? I just get a dead android picture :/
I've accidentally broken it by flashing the US ROM but my phone is the EU version. Boots up okay but has lost the IMEI and once the screen turns off won't turn on again - unless I reboot it.
Have so far failed to re-flash with the correct EU ROM - it just fails half-way through.
No, and I'm in the same situation with the firmware.

Categories

Resources