hi all developers i trying flash huawei Hol-T00 with spflash and it not complete flashing and the device stop ....
the computer stop detect the device and when i connected the battery it go vibration long time and still not detected from the pc
plz who to get connect any jumper can make the device to detect on the pc ??
plz help thanks for all ..
Related
I am using a lenovo p770 and today it froze... the screen was on but not responding..... so i pulled out the battery and now it doesnt even power up.... so i tried charging it and usually the indicator light glows red but now it did not... however when i pulled out the battery and continued the charging the red light came on..... and when i put the battery back in it turned off again... the phone is rooted so no warranty..... can neone help me out or at least point me in the direction of what might be wrong..... ???
i rooted the phone long time back.... abt 6 months ago and must have tried several custom roms several times.... all this while the phone was running fine.....
Thank you..
more info on the problem
Pls help...
I tried to use sp flash tools to flash the preloader....... when i connect the phone to the pc the mediatek vcom usb device is detected but as soon as sp flash tools try to write the device disconnects and i get the error that emmc not found.... i tried multiple times... i uninstalled old drivers and installed new drivers but everytime i get the same problem.... if i dont use sp flash tools then the device stays connected a little while longer but eventually disconnects within a minute....
so does the phone stand a chance of being repaired cause it gets detected at least even if its not powering up...??
I'll be trying to do the same on a completely fresh system till then ne ideas of what cld be wrong and wht cld i do to repair it would be nice.....
thank you....
Help-me I have Problem
I have a problem , when I try to Download the recovery.img , the green circle not showing , it is only an error message , under the device manager ... when I connect the phone , the computer recognize it but it is disabled after 2 second , ... and the process fails .
is there any solution for the driver disconnection ?
sir I need your help my phone k touch a 11 is fully dead even not glow screen sir am use your mathed to flashing it use sp flash tool but it not working because phone not show connection between pc Am use sp flash tool to flash it but not connected with pc and my pc drive are installed properly because others device are connected and vecome driver working properly sir my friends are flash it wrong room files then my phone is dead
after rewriting
PRELOADER and DSP_BL with another phone's.
The phone was dead, no led when connected to
usb and of course no activity on flash tool as
the usb port was not activating.
Sir phone not connected with pc so flash tool not flash my phone
hi guys.need help . I have bootloop problem with my g610. it only reboot when logo shows and I have to unplug battery.I cant use SP flash tools or other programs cause when I connect it to my pc it connect for a while and disconnect .any ideas to connect my phone to pc . by the way I tryed to connect without bat but same problem happend. (sry for my english)
help
before doing this things I'm backed up phone with mtk droid tools.
help
any suggestion?
Hello
I have an Lenovo s898t+ from aliexpress. with androdi 4.4.2 And I was trying to increase my file system root partition in phone. I use apk meteos MTK 6592, and after getting to recovery mode I did everithing like was write in other forumm that I found set factory restart. And now my phone is in something lie bootloop always showing android figure and when I try to turn it off only show
forrmating /data...
mount system/ error
and can`t get to recovery mode or if I try to connect to PC via USB without the batery inside the phone is still rebooting. I know how to flash stock rom, but cant do that becouse the phone is still connecting and disconnecting to PC.
Can somebody help please I have been searching for 4 days with no luck.
Thanks for all you answers
If your phone is a MTK device..
U can flash a new rom..
With SPflash tools..
abhinavp649 said:
If your phone is a MTK device..
U can flash a new rom..
With SPflash tools..
Click to expand...
Click to collapse
Cant get phone to stable connection to PC always reseting without battery and with baterry the bootloop shows up and did not connect to pc
u have to start the download process from SPtools before connecting your phone to PC
hopefully, it will show your phone..
some phones have a trigger to start the download..may be power button or any of volume buttons..
Some phone also required to pop in the battery to start the process..
Try any of these options..
hopefully, u will have ur phone flased with a new rom..
ingshibbby said:
Cant get phone to stable connection to PC always reseting without battery and with baterry the bootloop shows up and did not connect to pc
Click to expand...
Click to collapse
u have to start the download process from SPtools before connecting your phone to PC
hopefully, it will show your phone..
some phones have a trigger to start the download..may be power button or any of volume buttons..
Some phone also required to pop in the battery to start the process..
Try any of these options..
hopefully, u will have ur phone flased with a new rom..
Hey, I got wiko ridge 4g that was bricked, it won't turn on but the light is blinking when battery is not full when i connect him on charger. I have connected the phone with PC via USB and he recognized him as 'qhsusb_bulk', i tried to unbricked it with SRK Tool 2.0, but i can't turn on usb debbuging and i don't know if the phone is rooted or not, but i did it anyway. So i managed to delete partitions with that program, but later the phone was recognized as Unknown USB Device. So my question is : is there any other way to brick the phone back, without phone being turned on, via PC ?
Thank you very much.
muki22 said:
Hey, I got wiko ridge 4g that was bricked, it won't turn on but the light is blinking when battery is not full when i connect him on charger. I have connected the phone with PC via USB and he recognized him as 'qhsusb_bulk', i tried to unbricked it with SRK Tool 2.0, but i can't turn on usb debbuging and i don't know if the phone is rooted or not, but i did it anyway. So i managed to delete partitions with that program, but later the phone was recognized as Unknown USB Device. So my question is : is there any other way to brick the phone back, without phone being turned on, via PC ?
Thank you very much.
Click to expand...
Click to collapse
Hm, nobody answered to this ,so i keep digging out on internet,and after some searching i use the qfil app, also i downloaded original stock rom for my wiko ridge 4g, through qfil i installed that rom , the pc in one point recognized my device as 4g ridge, but then just started to showing quallcomm hs-usb diagnostic mode 9092 when it connected to PC via USB. My phone show some signs ,screen was black but it vibrating, and a assume it's turned on when i press touch screen or volume changer button he reproducing sound, but on pc he is readed like quallcomm hs-usb diagnostic mode 9092! If somebody know how to fix that problem, please answer me!