I've made sure I purchased the correct replacement for my screen. Followed a guide and got it all hooked up. The phone powers on but I get a white screen.
Anyone have any guesses as to what could be causing this?
Your help would be much appreciated as I would hate buying another phone.
Incorrect ribbon cable seat.
Take it apart and make sure that both the ribbon cable on the side, and the bottom with the tiny black screws are properly seated.
Yea i have tried all of that....but I just tried tinkering with it again and i was able to get a partial picture by changing the back pressure of where the LCD ribbon plugs into the other ribbon assembly the buttons are connected to.
So I am guessing there needs to be a super secure conenction at this point. Problem is...the black latch that holds the cable from the LCD to the other ribbon is broke so i cant make it pinch the cable.
Anyone know where I can find a replacement for this other than buying a broken hemes for parts?
You need the flex cable connection, and there is a site in canada that has them.
www.cnn.cn
Yea I checked that out....I don't see it, do you?
teknics said:
You need the flex cable connection, and there is a site in canada that has them.
www.cnn.cn
Click to expand...
Click to collapse
.cn is china not canada.
Good point - ca = canada
hi
i have a htc touch plus or as they call it htc touch dual.digitizer issue it stoped responding so i bought new one fitted in and still the same problem .i think is a software problem i guess driver software for touch screen .if any one can help please
thanks
Touch Dual digitizer
Hi Saliml2
Not convinced it is a software issue. My digitizer on T-Mobile Touch Plus did the same thing. It stated behaving erratically and then stopped responding altogether. I replaced the digitizer (via eBay) and it work for a few days and then stopped again.
I have read around the internet and have tried several ROM updates etc (currently running a WM 6.5.5 found in other area of this forum) but this has not solved the problem.
It seem to be an alignment issue - i.e. screen alignment is outside the screen area, but there seems to be no way of getting it back. Could be a fault on the phone mainboard (?) but there doesn't seem to be any info around apart from sending it to HTC for repair (not viable as the phone value negates this)
My phone is still not working, I might try opening it up again and reseating the digitizer cable but have done this twice already.
Have you try change the flex cable?
I had one to, with the same problem, and after changing the flex everything was ok...
Good luck!
Hi Amokh Just to clarify, what is the flex cable? The digitizer has a cable already attached to it that plugs in to a zif connector on the mainboard - I assume that this controls the data flow for the digitizer.
Any help would be appreciated.
deepthought2471 said:
Hi Amokh Just to clarify, what is the flex cable? The digitizer has a cable already attached to it that plugs in to a zif connector on the mainboard - I assume that this controls the data flow for the digitizer.
Any help would be appreciated.
Click to expand...
Click to collapse
Maybe this is helpfull http://www.pdacenter.ru/razborka/razbor_htc_touch_dual/
Goodluck
Flex cable, i was mean the cable between the mainboard and the lcd block, you can see it in the previous link, picture 20. Have you try it to change?
hello guys how did you manage to put the digitizer cable in place mine doesn t seem to get in place do i need something to hold the connector in place???
Hello all, I would ask where I can buy spare parts for htc legend. (Power / Volume button flex cable, middle housing etc.. etc..)
Thank you very much.
Depends on what you need,if its all of the above you will probably have trouble finding them,i was lucky and got another broken legend off ebay for the parts i needed try htcrepairs.com
bonesy said:
Depends on what you need,if its all of the above you will probably have trouble finding them,i was lucky and got another broken legend off ebay for the parts i needed try htcrepairs.com
Click to expand...
Click to collapse
Thanks for the reply. I try the headste's grid, where there is the LED notification. I also try the various volume's flex cable and power. Can you help? Thanks
P.S.
I apologize if I make grammatical errors.
Please help, I miss my tablet.I had the common problem with the power thingy inside the tablet going out so i opened it to solder but did not fix.So i ordered the charging dock and waited for a month and a half.I get it today and was so excited to only plug it it and got power and charging everything is perfect,i go to swipe over on my arrow to unlock the screen and nothing!I have no touch controls on screen what so ever.But the soft keys work,they do not do me any good but they work.The home key takes me to my home page and mag glass goes to the internet.Does any body have any ideas of what could have happened or what i can do to fix this,please????
alcapone1130 said:
Does any body have any ideas of what could have happened or what i can do to fix this,please????
Click to expand...
Click to collapse
First, check for disconnected or loose cables inside the gTab.
Next, if it isn't a HW fault like loose cables, then connect the USB cable to the gTab and run this ADB command (you will have to install and set up ADB if you haven't already done so):
Code:
C:\SOME\PATH> [B]adb shell "echo -n 1 > /sys/devices/platform/tegra_touch/calibration"[/B]
Digitizer Cable/Connection
alcapone1130 said:
Please help, I miss my tablet.I had the common problem with the power thingy inside the tablet going out so i opened it to solder but did not fix.So i ordered the charging dock and waited for a month and a half.I get it today and was so excited to only plug it it and got power and charging everything is perfect,i go to swipe over on my arrow to unlock the screen and nothing!I have no touch controls on screen what so ever.But the soft keys work,they do not do me any good but they work.The home key takes me to my home page and mag glass goes to the internet.Does any body have any ideas of what could have happened or what i can do to fix this,please????
Click to expand...
Click to collapse
The attached pdf contains photos of the digitizer/cables and their connections inside the gtab. Check for loose connection and/or broken wires on both ends.
Al
aabbondanza said:
The attached pdf contains photos of the digitizer/cables and their connections inside the gtab. Check for loose connection and/or broken wires on both ends.
Al
Click to expand...
Click to collapse
Ok,First thank you so much for helping.Ok,One of the cables you shown does have two broken wires,it is the kind of short wire with black cloth like material over it that runs unde the shiny brown plastic piece.Is there a way to fix that or rig it to get me back up and touching again?Thank you again for helping me out,and you already pinpointed my problem,now i am hoping you can fix it,lol.
Where is the break?
alcapone1130 said:
Ok,First thank you so much for helping.Ok,One of the cables you shown does have two broken wires,it is the kind of short wire with black cloth like material over it that runs unde the shiny brown plastic piece.Is there a way to fix that or rig it to get me back up and touching again?Thank you again for helping me out,and you already pinpointed my problem,now i am hoping you can fix it,lol.
Click to expand...
Click to collapse
I assume since you didn't send in under warranty for the power connector that it's no longer under warrantly!
Exactly where is the break? Close to (or at) one of the connectors? Which end (motherboard end or digitizer end) of the cable? Obviously closness to the connector makes it more difficult. I have seen a post where another use had the break pretty close to the connector & fixed it though.
Al
I totally forgot that i made a youtube video yesterday,here is the address http://www.youtube.com/watch?v=kFNRtDhr5EQ I have been so stressed out about getting my gtab back it slipped my mind.Oh, the broken end is what plugs under the silver area not under the brown area.
aabbondanza said:
I assume since you didn't send in under warranty for the power connector that it's no longer under warrantly!
Exactly where is the break? Close to (or at) one of the connectors? Which end (motherboard end or digitizer end) of the cable? Obviously closness to the connector makes it more difficult. I have seen a post where another use had the break pretty close to the connector & fixed it though.
Al
Click to expand...
Click to collapse
I totally forgot that i made a youtube video yesterday,here is the address http://www.youtube.com/watch?v=kFNRtDhr5EQ I have been so stressed out about getting my gtab back it slipped my mind.Oh, the broken end is what plugs under the silver area not under the brown area.
alcapone1130 said:
I totally forgot that i made a youtube video yesterday,here is the address http://www.youtube.com/watch?v=kFNRtDhr5EQ I have been so stressed out about getting my gtab back it slipped my mind.Oh, the broken end is what plugs under the silver area not under the brown area.
Click to expand...
Click to collapse
If you magnify the digitizer circuit (lower photo in the pdf) you will see the label for each of the lines in the cable. Assuming the lines run straight thru, it looks like the ones that broke are the power & ground to the circuit (VSS & GND). That would explain the touch screen not working at all.
Hard to tell from the video where the breakis, but it looks real close to the connector.
Your best bet may be looking for someone who has a broken digitizer (outer glass) or gTab and is selling it for parts. I looked in the Marketplace forum here on XDA & there is one non working gtablet someone is asking $55 for. I also saw another one up for bid on ebay ($40 latest bid). You my have to ask if the cable is good on them.
Not a whole lot of options for repair. As you've already experienced, the cable is small & fragile.
If the connector has removable pins then you could remove the pins, solder the wire to it & reinsert the pins, BUT from the picture it doesn't look like they are removeable.
You could solder the 2 wires to the pins coming out the back of the socket but they look too small to easily solder to.
The last option would be to rigg the cable to work. There are a couple of possibilites but I would rather you consider the other options before suggesting a repair of the cable itself. If you can, see if you can take a closeup, high res photo of the back fo the connector where the wire broke. PM me & I'll send you my email address to send it too.
Al
aabbondanza said:
If you magnify the digitizer circuit (lower photo in the pdf) you will see the label for each of the lines in the cable. Assuming the lines run straight thru, it looks like the ones that broke are the power & ground to the circuit (VSS & GND). That would explain the touch screen not working at all.
Hard to tell from the video where the breakis, but it looks real close to the connector.
Your best bet may be looking for someone who has a broken digitizer (outer glass) or gTab and is selling it for parts. I looked in the Marketplace forum here on XDA & there is one non working gtablet someone is asking $55 for. I also saw another one up for bid on ebay ($40 latest bid). You my have to ask if the cable is good on them.
Not a whole lot of options for repair. As you've already experienced, the cable is small & fragile.
If the connector has removable pins then you could remove the pins, solder the wire to it & reinsert the pins, BUT from the picture it doesn't look like they are removeable.
You could solder the 2 wires to the pins coming out the back of the socket but they look too small to easily solder to.
The last option would be to rigg the cable to work. There are a couple of possibilites but I would rather you consider the other options before suggesting a repair of the cable itself. If you can, see if you can take a closeup, high res photo of the back fo the connector where the wire broke. PM me & I'll send you my email address to send it too.
Al
Click to expand...
Click to collapse
Wow,Thank you so so much,Can you get me in contact with the guy with the gtab for $55.00,i will buy it and transfer the cash to him immediately,that sounds like the best bet.I will msg you a really good photo still,incase i can not get my hands on the one for sale,but if i can let him know or maybe you could let him know that i will buy it quick enough maybe i can end up with it.I would really feel better just swapping the cable out with another.I will talk back with you tomorrow and again thank you for your time and great help,i really owe you.
Marketplace & Non Working Tab Links
alcapone1130 said:
Wow,Thank you so so much,Can you get me in contact with the guy with the gtab for $55.00,i will buy it and transfer the cash to him immediately,that sounds like the best bet.I will msg you a really good photo still,incase i can not get my hands on the one for sale,but if i can let him know or maybe you could let him know that i will buy it quick enough maybe i can end up with it.I would really feel better just swapping the cable out with another.I will talk back with you tomorrow and again thank you for your time and great help,i really owe you.
Click to expand...
Click to collapse
Here are several link for you
1. XDA Marketplace http://forum.xda-developers.com/forumdisplay.php?f=1321
2. Link to "Wanting to sell" subformum where I found the non working gtab (used forum search for gtablet) http://forum.xda-developers.com/forumdisplay.php?f=476
3. Link to not working gTab http://forum.xda-developers.com/showthread.php?t=1436549&highlight=gtablet.
Take a look at this post & email him to make sure you want it.
Al
aabbondanza said:
Here are several link for you
1. XDA Marketplace http://forum.xda-developers.com/forumdisplay.php?f=1321
2. Link to "Wanting to sell" subformum where I found the non working gtab (used forum search for gtablet) http://forum.xda-developers.com/forumdisplay.php?f=476
3. Link to not working gTab http://forum.xda-developers.com/showthread.php?t=1436549&highlight=gtablet.
Take a look at this post & email him to make sure you want it.
Al
Click to expand...
Click to collapse
Its amazing what a couple of stripped bread ties will doo,lol.I took a bread tie and stripped the paper off of it,cut it to the length I needed and wrapped the remaining wire to one end and pushed the other end of the tie inside the pin hole,lol.It worked like a champ! MY Grab has been up and running for over a month,I just knocked on my coffee table,lol.Thank you for helping me out I really appreciated you trying everything to help me.I am so happy to have it back,now if I can just figure out why I keep seeing black boxes on my games when I play them I will really be doing fine.Thank you again.
Hello and Happy New Year to all members and guests in this great community.
I droped my phone very hard on the floor and i smashed the digitizer and the screen destroyed too (actually from the screen was broken the flex cable on the base of the screen).
Now of course it wouldn't turn the screen on and makes no buzz sound when i press the power button.
When i connect it to my pc through the USB cable it does nothing (i pulled out my sd card, can this be a reason?).
My question is, if i replace the screen and the digitizer it will work? or the fact that it does not connect to my pc might hide other hardware issues?
From a closer look i didn't see any cracks on the plack's surface.
Any help would be acceptable and appreciated.
Thanks
tolakos100 said:
Hello and Happy New Year to all members and guests in this great community.
I droped my phone very hard on the floor and i smashed the digitizer and the screen destroyed too (actually from the screen was broken the flex cable on the base of the screen).
Now of course it wouldn't turn the screen on and makes no buzz sound when i press the power button.
When i connect it to my pc through the USB cable it does nothing (i pulled out my sd card, can this be a reason?).
My question is, if i replace the screen and the digitizer it will work? or the fact that it does not connect to my pc might hide other hardware issues?
From a closer look i didn't see any cracks on the plack's surface.
Any help would be acceptable and appreciated.
Thanks
Click to expand...
Click to collapse
C'mon guys (and girls too of course)
I don't believe that in the bigest community of mobile technology can't anyone help me!!!
If the phone is ok, despite the cracked screen and digitizer, will it work if i connect it to my pc or not?
Thanks on any answer.
if your phone wont connect to PC or vibrate on startup, Im sorry to say that but your motherboard is damaged and replacing by new one is expensive! bad luck budy! this was my bad luck few months ago