Hello!!!
I've noticed it wasn't only me who are stuck with their HTC Desire 310 (an MT6582) Brick because of a faulty flash!
Since SP Flash Tools refuses to flash the phone since the phone is disconnected after 2 seconds from booting it in Meta/Preloader mode we are not able to flash it.
so Please if anyone could help us to get that phone flashed alot of people will be happy for that me 1st!
****now for everyone to know the details of the issue****
1- After flashing anything whatever it was the phone will get Hard Brick which means that Preloader or Bootloader "1st 2 data partations" is faulty.
2- Since Factory Mode is in Bootloader so you are not able to access it
3- since adb starts after bootloader phase so also u cant access it.
4- THANKFULLY we can get the phone into Preloader Mode by Removing Battery ===> connect usb ===> then hold Volume Down
5- In Preloader Mode the phone shutsdown in approxmatly 2-3 seconds getting SP Flash Tool Recognising it for 2 seconds only to give you the RED bar and an Error of S_BROM_DOWNLOAD_DA_FAIL(2004).
6- You can also get the phone into Preloader mode by Removing battery =====> connect USB =====> plug the battery back in. the phone will get into Preloader Mode for 2 seconds too then will shutdown then will get into Battery Charging mode that also don't work and will make the phone Load then Bootloop on the Splash Screen not ANDROID Bootanimation
((((IF you noticed everything happens because Preloader mode doesnt stay on more than 2 seconds))))
1- Preloader Mode connecting for 2 seconds is actually NORMAL and that's what is suppose to be as alot of people saying and it will stay in preload mode when SP Flashtool recognise it.. however that isn't happening with us, the flash tool recognise the phone "it goes from idel to RED bar means that phone disconnected" so there must be something would keep the phone from shutting down.
Please give me help i'm trying to revive my friend's phone... Thank you in advance...
Related
Hi guys, I recently purchased a Homtom HT3 for my mother, when it arrived to me I charged it and checked it out a bit just to make sure everything was fine which it was.
She collected it from me the next day and told me she'd start to use it the day after, she calls me up the next day and tells me there's some problems with it and a few people at her workplace tried to fix it for her to no avail. I pick the phone back up and I notice that everytime I power it on, it gets stuck on the "homtom" logo.
As I don't know too much about fixing phones I only took the following steps before asking for advice here; I went into recovery mode by holding up volume and power button, the android guy with the red triangle appeared so I tapped up + power button to get into the recovery(?) menu. I wiped the phone to factory settings and deleted the cache in there but it hasn't fixed the problem.
I assume I need to flash a firmware or something to potentially fix this, but I'm unable to find an official firmware from doogee/homtom's site for the HT3. I've found a firmware that I downloaded from "chinagadgetsreviews" but I'm a bit weary to try and flash with that rom because it isn't from the manufacturer. (even if I knew how to - the only experience I have is rooting my own phone but that's when I actually had access to a working phone, not one thats stuck on a boot logo).
Sorry for the long post but could anyone guide me in the right direction here? TIA
I'm not opposed to not using official firmware, I think I use cyanogen mod(?) on my own phone. I'd just like the problem fixed in the easiest way possible.
Trying to fix it myself by flashing a rom via SP flash tools but I've ran into another problem which is stopping any kind of progress - the phone isn't detected in Windows, I can't enable usb debugging because I can't get passed the boot loop, I've tried installing the ADB driver manually which didn't seem to work (just said it didn't install correctly and left me with a yellow exclamation mark) and I tried to install it automatically via ADB driver installer but it just throws up an error that the device isn't detected.
Any help would be greatly appreciated.
Hello. I bought a Homtom HT3 and next day a done an update with sp flash tool. all gone ok, but phone now wont to turn on. I contact homtom and got all drivers and room to fix it. Now i have a problem , i hit download on flash tool , take off battery + pres volume down + conect phone on usb cable. My computer detect it as USB MTK PORT sp flash tool load only the first red line but not detecting phone info, then after 1 minute i get
s_ft_da_no_response(4001) da didn't send response data to flash tool.
I changed drivers port even to MTK preloader, but i get same error.
NOTE....... All drivers and rom i got original from HOMTOM.
Thanks to all who can help me.
I can show a screenshot if need.
Same here - any solution for this problem?
Kleos89 said:
Hello. I bought a Homtom HT3 and next day a done an update with sp flash tool. all gone ok, but phone now wont to turn on. I contact homtom and got all drivers and room to fix it. Now i have a problem , i hit download on flash tool , take off battery + pres volume down + conect phone on usb cable. My computer detect it as USB MTK PORT sp flash tool load only the first red line but not detecting phone info, then after 1 minute i get
s_ft_da_no_response(4001) da didn't send response data to flash tool.
I changed drivers port even to MTK preloader, but i get same error.
NOTE....... All drivers and rom i got original from HOMTOM.
Thanks to all who can help me.
I can show a screenshot if need.
Click to expand...
Click to collapse
Hello. I bought a Homtom HT3 and next day a done an update with sp flash tool. all gone ok, but phone now wont to turn on. I contact homtom and got all drivers and room to fix it. Now i have a problem , i hit download on flash tool , take off battery + pres volume down + conect phone on usb cable. My computer detect it as USB MTK PORT sp flash tool load only the first red line but not detecting phone info, then after 1 minute i get
s_ft_da_no_response(4001) da didn't send response data to flash tool.
I changed drivers port even to MTK preloader, but i get same error.
NOTE....... All drivers and rom i got original from HOMTOM.
Thanks to all who can help me.
I can show a screenshot if need.
Once the red line loads, try putting back the battery. Sometimes the handset needs power from the battery. I did that with my HT3: once SP Flash Tool detected my phone, I put the battery back.
hi. so my problem is that my phone does not turn on, i cant go to recovery or do hard reset. the phone react when i plug it in PC without battery, but its always connect and disconnect over and over again. i have downloaded the omap drivers and instaled it. now i have in the device manager a OMAP4430 FastBoot USB device. by the drivers was a fastboot emulator. but when i will flash rom, kernel or recovery a just get partition does not exist. can someone help me please? srry for english.
Does your phone not turn on at all when holding down the power button? If it boots up, and gets stuck on a loop or has an error message, that is different. But if it doesn't turn on at all, then your battery is dead or something is wrong with your phone's hardware. If you connect your phone to the PC (with the battery on), does it at least show a light? Or does it boot up at all when you hold the power button? If it doesn't show a light or boot up, it is not your battery, but your phone's hardware. Your phone might have been dropped or water inside it or it was microwaved? I know it sounds silly, but something happened to the phone physically. Now if you connect it to the PC and you see a light but it never boots, your device is bricked. Not accusing you, but you might have tried rooting it or writing over a partition on your phone which caused to brick. Also, try typing in fastboot devices. If it shows up a device, that means it is connected. Cheers!
No the phone does not turn on and it shows nothing, even when i put it on charger. If i connect to pc with battery after i installed the omap driver it just connect and disconnect over and over again, windows make this sound when you connect and disconnect something. I have flashed a new rom. It has worked but after some time its stoped. So i have try flashed it again but i could not get in recovery. A files was missing and after i try flashing thhe recovery its just dead. I can connect it just with the fastboot emulator because it's don't connect when i just put it on pc. I must connect it without battery wait 4 sec and then put the battery back. Than i can see in the emu my phone but not able flash anything because of partition does not exist
I was trying to install a modified ROM in redmi note 3. The rom had a modified emmc_appsboot.mbn and a modded recovery.img. I entered in sp flash tool and was flashing the rom and the app crashed or battery ran out while installing. Now the fastboot and the os were bricked. At this point when I tried to boot the MI logo was showing up for a second and then it reboots. At this point, it was showing up as a fastboot device on my pc so I tried using command fastboot reboot edl and it worked (in the black screen). now in edl mode (red light blinking when plugged in), I tried installing stock rom and again it was interrupted ( due to maybe battery issue). Now when I connect the device to pc it detects as 900e instead of 9008, whenever I press the power button it blinks red light like in edl mode ( this may also happen if the battery has no juice), I cannot charge coz its still in edl mode.
I tried Deep Flash cable, it didn't work. I then manually updated the driver from 900e to 9008, it shows up in mi flash tool but installation fails with the error cannot receive hello package.
After ****ing my device this much I went to a mi service center and they said that when they try to install software, it fails. They dunno why, I guess the battery is not enough to install the software.
Finally, They asked to replace the motherboard. since spending 5k on kenzo in october 2018 is a waste any bright minds have any idea for repair,?
ISH99 said:
I was trying to install a modified ROM in redmi note 3. The rom had a modified emmc_appsboot.mbn and a modded recovery.img. I entered in sp flash tool and was flashing the rom and the app crashed or battery ran out while installing. Now the fastboot and the os were bricked. At this point when I tried to boot the MI logo was showing up for a second and then it reboots. At this point, it was showing up as a fastboot device on my pc so I tried using command fastboot reboot edl and it worked (in the black screen). now in edl mode (red light blinking when plugged in), I tried installing stock rom and again it was interrupted ( due to maybe battery issue). Now when I connect the device to pc it detects as 900e instead of 9008, whenever I press the power button it blinks red light like in edl mode ( this may also happen if the battery has no juice), I cannot charge coz its still in edl mode.
I tried Deep Flash cable, it didn't work. I then manually updated the driver from 900e to 9008, it shows up in mi flash tool but installation fails with the error cannot receive hello package.
After ****ing my device this much I went to a mi service center and they said that when they try to install software, it fails. They dunno why, I guess the battery is not enough to install the software.
Finally, They asked to replace the motherboard. since spending 5k on kenzo in october 2018 is a waste any bright minds have any idea for repair,?
Click to expand...
Click to collapse
Remove the battery . fully charge it and put it back and do ur experiment.
first charge your phone properly and have a look your phone is in which state.
Hello Members,
The device was stuck in boot loop so i tried to flash via EDL mode. First it came to edl mode but while flashing i got some XML error. Now i tried to put the phone again in EDL mode but its not working.
I had removed the battery and and i have connected to 2 jumper pins 1 and 4 and connect the usb but the phone dont seems to come to edl mode. just flashes the MI screen and power off repeatedly.
Now i connect the phone directly with battery on and its coming as charging but surprisingly the phone got detected, the device manager shows the phone as Linux file stor gaget usb device. I tried to flash with mi flash tool and its running indefinitely saying flashing..
Help...